Electrical and dielectric properties of glass system NaPO3–KHSO4

Glass samples have been prepared in the NaPO₃–KHSO₄ binary system with the classical melting, casting and annealing steps. Electrical and dielectrical properties of glass samples were studied. Measurements of DC and AC conductivity and complex electrical permittivity of xNaPO₃–(100 ? x)KHSO₄ glass system were carried out at temperatures ranging from room temperature to temperature located 15 °C below glass transition temperature T_g. Results showed that changes of NaPO₃ concentration considerably affect values of observed parameters. DC conductivity of glass increases as NaPO₃ concentration grows until concentration x = 60. However, beyond this value a sharp decrease of DC conductivity was observed. In addition relaxation times showed abrupt changes at concentration x = 60, corresponding to the lowest relaxation times at the temperature 90 °C.     

Investigation of the conductivity of the lithium borosilicate glass system

The lithium borosilicate system (Li₂O)_0.4(B₂O)_(0.6x)(Si₂O₄)_0.6(1−x) with x = 0, 0.2, 0.3, 0.4, 0.6, and 0.8 was investigated using impedance spectroscopy. Impedance spectra were taken in the frequency range from 50 Hz to 1 MHz and in the temperature range from 100 to 280 °C. The ac- and dc-conductivity, relaxation frequency and activation energy of the dc-conductivity were extracted from the impedance spectra. The dc-conductivity of the investigated glass samples increases almost linearly from silica rich (x = 0) to the boron rich (x = 0.8) samples. Activation energy (E_a) was found to be 0.65 eV for high conducting sample and 0.8 eV for low conducting sample, respectively. The mixed glass-former effect was not observed on the samples studied. The effect of temperature scaling of ac-conductivity was observed, which indicates, that ionic conductivity relaxation mechanism is temperature independent for samples with x = 0, 0.2, 0.3. However, some deviations from scaling were found for the samples with higher x (x = 0.4, 0.6, 0.8).     

Growth and characterization of lead-free Ba(1−x)CaxTi(1−y)ZryO3 single crystal

A lead-free Ba_(1?x)Ca_xTi_(1?y)Zr_yO₃ (BCZT) single crystal (x=0.08, y=0.26) was grown by the Czochralski (CZ) method in a mixed flux of TiO₂ and ZrO₂. The composition of as-grown BCZT was analyzed by electron probe micro-analysis. The structure, dielectric properties and phase transition were investigated at different temperatures. The X-ray diffraction results confirmed that the structure of the as-grown BCZT crystal was cubic both at 25 °C and 500 °C. The temperature dependence of the dielectric constant and Raman spectra characterization revealed that there was a phase transition from cubic to tetragonal, which happened between 200 K and 250 K. With increasing frequency, the Curie temperature shifted towards high temperature.     

Conductivity percolation transition of Agx(Ge0.25Se0.75)100−x glasses

The ionic conductivity of several chalcogenide glasses increases abruptly with mobile ion addition from values typical of insulating materials (10⁻¹⁶–10⁻¹⁴ Ω⁻¹ cm⁻¹) to values of fast ionic conductors (10⁻⁷–10⁻¹ Ω⁻¹ cm⁻¹). This change is produced in a limited concentration range pointing to a percolation process. In a previous work [M. Kawasaki, J. Kawamura, Y. Nakamura, M. Aniya, Solid State Ionics 123 (1999) 259] the transition from semiconductor to fast ionic conductor of Ag_x(Ge_0.25Se_0.75)_100−x glasses was detected at x¹ ≅ 10 at.% in the form of a steep change in the conductivity. Ag_x(Ge_0.25Se_0.75)_100−x glasses with x ⩽ 25 at.%, prepared by a melt quenching method, are investigated by impedance spectroscopy in the frequency range 5 Hz–2 MHz at different temperatures, T, from room temperature to 363 K and by DC measurements at room temperature. The conductivity of the glasses, σ, was obtained as a function of silver concentration and temperature. For x ⩾ 10 at.% our results are in agreement with those reported by Kawasaki et al. [M. Kawasaki, J. Kawamura, Y. Nakamura, M. Aniya, Solid State Ionics 123 (1999) 259]. The percolation transition was observed in the range 7 ⩽ x ⩽ 8. The temperature dependence of the ionic conductivity follows an Arrhenius type equation σ = (σ_o/T) · exp(−E_σ/kT). The activation energy of the ionic conductivity, E_σ, and the pre-exponential term, σ_o, are calculated. The results are discussed in connection with other chalcogenide and chalcohalide systems and linked with the glass structures.     

Nanostructural and optical features of amorphous AlxSi0.45−xO0.55 (0 ⩽ x ⩽ 0.05) thin films prepared by RF-magnetron sputter techniques

The nanostructural, chemical, and optical features of Al_xSi_0.45−xO_0.55 (0 ⩽ x ⩽ 0.05) thin films were investigated in terms of Al concentration and post-deposition annealing conditions; the films were prepared by co-sputtering a Si main target and Al-chips, and the annealing was carried out at temperatures of 400–1100 °C. The a-Si_0.45O_0.55 films prepared without Al-chips and annealed at 800 °C contain ∼3.5 nm-sized Si nanocrystallites. The photoluminescence (PL) intensity as well as the volume fraction of Si nanocrystallites increased with increasing the concentration of Al to a certain level. In particular, the intensity of the PL spectra of the Al_0.025Si_0.425O_0.550 films which were annealed at 800 °C increased significantly at wavelengths of ∼580 nm. It is highly likely that the observed increase in the PL intensity is caused by the raise in the total volume of the ∼3.5 nm-sized nanocrystallites in the films. The addition of Al as well as the post-deposition annealing allow adjustment and control of the nanostructural and light-emission features of the a-SiO_x films.     

Glasses in the SbPO4–WO3 system

Glasses in the binary system (100 − x)SbPO₄–xWO₃ (20 ⩽ x ⩽ 60, x in mol%) have been prepared and characterized. Differential thermal analysis (DTA) shows that the glass transition temperature, T_g, increases from 412 °C, for samples containing 20 mol% of WO₃, to 481 °C observed for glass containing 60 mol%. Sample containing 40 mol% in WO₃ were observed to be the most stable against devitrification. The structural organization of the glasses has been studied by using Fourier transform infra-red (FTIR), Raman, ³¹P Magic angle spinning (MAS) and spin echo nuclear magnetic resonance (NMR) spectroscopies. Results suggest two distinct networks comprising the glass structure, one with high SbPO₄ content and the other characteristic of the highest WO₃ content samples. The glasses present photochromic properties. Colour changes are observed for samples after exposure to ultraviolet or visible laser light. XANES, at L₁ absorption edge of tungsten, suggests partial reduction from W⁶⁺ to W⁵⁺ species during the laser irradiation. The photochromic effects and the colour changes, promoted by laser excitation, are reversible and easily removed by heat for during 1 h at 150 °C. Subsequent ‘write/erase’ cycles can be done without degradation of the glasses.     

Microstructure and properties of spark plasma sintered Fe–Cr–Mo–Y–B–C bulk metallic glass

Fabrication of Fe-based amorphous alloy using spark plasma sintering (SPS) process has been reported. Fully amorphous compacts with ～95% relative density were successfully sintered at temperature about 100 °C lower than glass transition temperature (T_g: 575 °C). Formation of crystalline Fe₂₃(C, B)₆ phases within near-fully dense (～99%) amorphous matrix is observed at sintering temperatures (>550 °C) close to glass transition temperature. Microstructure evolution in sintered compacts indicated that density, degree of crystallinity, and mechanical properties can be effectively controlled by optimizing SPS parameters.     

Glassy state and structure of Sn–Sb–Se chalcogenide alloy

The effect of Sn addition on the glass transition and structure of c-Sb₂₀Se₈₀ chalcogenide alloy have been studied by X-ray diffraction and differential scanning calorimetric studies. The increase in the glass forming region and the glass transition temperature with the addition of Sn is discussed by considering the formation of [SnSe₄] tetrahedra, another type of network former, which inhibits the crystallization. The differential scanning calorimetric studies on Sn_xSb₂₀Se_80−x (8 ⩽ x ⩽ 18) glassy samples reveal a single glass transition temperature for all values of x while a single crystallization peak was obtained only for 10 ⩽ x < 12. The X-ray diffraction studies reveal that the glass crystallizes to Sb₂Se₃ and SnSe₂ phases upon annealing. The glass formation and composition dependence of glass transition temperature in the Sn–Sb–Se chalcogenide alloy could be understood by considering the topological phase transitions and a chemically ordered network model.     

Phase composition,microstructure and conductivity of (85-α)VO2–15(Vanadium–Phosphate–Glass)–αCu glass–ceramics

Electric conductivity, microstructure and phase composition of (85-α)VO₂–15VPG–αCu glass–ceramics (VPG = Vanadium–Phosphate–Glass) with copper content in the interval 0 wt% ⩽ α ⩽ 15 wt% were investigated. VPG is the glass (molar %) 80V₂O₅–20P₂O₅. Only two phases: VO₂ and VPG were identified when α ⩽ 5 wt%. VO₂ crystallites, VPG and pores are observed in these ceramic microstructures. Glass forms layers 1–2 μm thick in the space between VO₂ crystallites. The copper is dissolved in VPG during glass–ceramic synthesis. It increases the electric conductivity of the glass and provides improvement of electrical bonds between VO₂ crystallites. Therefore glass–ceramics conductivity exhibits an abrupt change of approximately 100× in the vicinity of the phase transition temperature, T_t, in VO₂. A new crystalline phase appears in (85-α)VO₂–15VPG–αCu ceramics when α ∼ 6 wt%. This phase is observed as small crystallites with the sizes of 1–5 μm. The increase in such phase content, with an increase in copper content is accompanied by a decrease in the content of VO₂. Percolation along the new phase is a primary contributor to electric conductivity when α ⩾ 8 wt%. In this case the conductivity exhibits no abrupt change in the vicinity of the temperature T_t. The new phase is probably the bronze Cu_xV₂O₄. It crystallizes from a liquid phase during glass–ceramics synthesis.     

Incorporation of B2O3 in CaO-SiO2-P2O5 bioactive glass system for improving strength of low-temperature co-fired porous glass ceramics

Bioactive glass ceramics (BGCs) have different rates of biodegradation and mechanical properties depending on their chemical compositions and sintering temperatures. The present study was aimed to develop the boron-rich, phosphorus-low CaO–SiO₂–P₂O₅–B₂O₃ bioactive glasses (BG-B_x, X = 0, 10, 20) potentially for improving the mechanical properties of BGCs via low-temperature co-fired process. The B₂O₃-free BG-B₀ shrunk well at ~ 726 °C and melted at over 1050 °C, while the onset shrinking and melting temperatures of the 20 mol% B₂O₃-doped BG-B₂₀ was lowered to ~ 648 °C and ~ 952 °C, respectively. The BG-B₂₀ thermally treated at 850–950 °C was transformed into wollastonite and calcium borate, and crystallization decreased the kinetics but did not inhibit the development of hydroxyapatite on their powder and disc surface when immersed in simulated body fluid. The in vitro degradation in Tris buffer confirmed that the degradation rate markedly increased with increasing boron content in BG-B_x. The compressive strength and flexural strength of the 10% BG-B₂₀-reinforced 45S5 porous BGC sintered at 850 °C was nearly four times than that of 45S5 porous constructs. These studies suggest that the boron-rich, phosphorus-low CaO–SiO₂–P₂O₅–B₂O₃ system is a promising biomaterial and potential low temperature co-fired aid for improving the mechanical and biological properties of porous BGCs.     

Structure and electrical properties of nitrided NbN–TiN sol–gel derived films

The results of investigations of electrical conductivity and the structure of NbN–TiN thin films in a different NbN/TiN molar ratio are presented in this work. Sol–gel derived xNb₂O₅?(100?x)TiO₂ coatings (where x = 100, 90, 80, 70, 60, 50, 40, 0 mol%) were nitrided at 1200 °C to obtain NbN–TiN films. The structural transformations occurring in the films as a result of ammonolysis were studied using X-ray diffraction (XRD), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The electrical conductivity was measured with a conventional four-terminal method in the temperature range of 5–280 K. The NbN–TiN samples exhibited a negative temperature coefficient of resistivity. The positive temperature coefficient of resistivity was observed only for the x = 0 sample. The results of conductivity versus temperature may be described on the grounds of a model proposed for a weakly disordered system. The film thickness effect on the superconducting properties was studied for x = 80 and x = 100 samples. The superconducting transition was not observed in all samples, the exception was x = 80 sample, 1050 nm in thickness. It is not clear, why all x = 100 samples do not exhibit superconducting transition in resistivity measurements. It seems to be possible, that the Josephson junction formation between NbN grains could be blocked by non-superconducting phases present in these samples.     

EPR and magnetic susceptibility studies of B2O3–Bi2O3–Gd2O3 glasses

Glasses of the xGd₂O₃ · (100 − x)[B₂O₃ · Bi₂O₃] system with 0.5 ⩽ x ⩽ 10 mol% were studied by electron paramagnetic resonance (EPR) and magnetic susceptibility measurements. Data obtained show that for low gadolinium oxide contents of the samples (x ⩽ 3 mol%) the Gd³⁺ ions are randomly distributed in the host glass matrix and are present as isolated and dipole–dipole coupled species. For higher gadolinium oxide contents of the samples (x > 3 mol%) the Gd³⁺ ions appear as both isolated and antiferromagnetically coupled species. The EPR spectra of the glasses reveal resonance sites with an unexpected high crystalline field in addition to the ‘U’ spectrum, typical for Gd³⁺ ions in disordered systems. This absorption line is due to Gd³⁺ ions that replace Bi³⁺ ions from the host glass matrix and could play the network unconventional former role in the studied glasses.     

Preparation and ionic conductivity of transparent glass−ceramics containing a large quantity of lithium−mica

In order to crystallize a large quantity of the lithium?mica in glass?ceramics, 5.1 mass% MgF₂ was added to the starting materials of the parent glasses having chemical compositions of Li_(1+x)Mg₃AlSi_3(1+x)O_10+6.5xF₂ (x = 0.5 and 1.0). Transparent glass?ceramics, in which a large quantity of lithium?mica with particle size of <50 nm was separated, could be prepared from the MgF₂-added parent glass with x = 0.5. While the parent glass, which had a binodal phase separation structure, did not exhibit electrical conductivity, the transparent glass–ceramic was given conductivity by the formation of an interlocking structure of mica. As the separated mica formed a tighter interlocking structure, the conductivity increased and reached a value of 2.0 × 10^?3 S/cm at 600 °C. The MgF₂-added parent glass with x = 1.0 was not transparent because of coarse spinodal phase separation. The conductivity was 4.3 × 10^?4 S/cm at 600 °C but was significantly decreased by the separation of mica.     

Raman spectroscopic study of some lead phosphate glasses with tungsten ions

The structure of xWO₃ · (100 − x)[2P₂O₅ · PbO] glass system with 0 ⩽ x ⩽ 50 mol% was investigated by Raman spectroscopy. The characteristic bands of these glasses due to the stretching and bending vibrations were identified and analyzed by the increasing of WO₃ content. This fact allowed us to identify the specific structural units which appear in these glasses and thus to point out the network modifier role of tungsten oxide for low concentrations and its former role at high concentrations.     

Thermal conductivity of mixed alkali silicate glasses at low temperature

Thermal conductivity of glass is one of the fundamental properties of it. However, that has not been studied enough. That of only less than 20 compositions has been measured below the room temperature. In this study, we measured the thermal conductivity of xNa₂O · (100 ? x)SiO₂ and (33 ? y)Na₂O · yCs₂O · 67SiO₂ glasses by a transient heating method in the temperature range from about 150 K to room temperature. The conductivity of xNa₂O · (100 ? x)SiO₂ is found to decrease with the increase in alkali content. The dominant factor of this behavior is the decrease in phonon mean free path, which is due to the increase of non-bridge oxygen. Thermal conductivity of (33 ? y)Cs₂O · yNa₂O · 67SiO₂ is decreased with the increase in Cs₂O/(Na₂O + Cs₂O) ratio. The dominant factor of this behavior is the decrease of sound velocity. However, composition dependence of the phonon mean free path also affects the thermal conductivity. Phonon mean free path of 33Cs₂O · 67SiO₂ glass is longer than that of 33Na₂O · 67SiO₂ glass, and should be related to the change in distribution of structural unit in glass. In addition, phonon mean free path of mixed alkali glasses are shorter than that of single alkali glasses.     

Electrical properties of A2.6+xTi1.4−xCd(PO4)3.4−x (A = Li,K; x = 0.0–1.0) phosphate glasses

Electrical properties of A_2.6+xTi_1.4−xCd(PO₄)_3.4−x (A = Li, K; x = 0.0–1.0) phosphate glasses are investigated over a frequency range from 42 Hz to 1 MHz at different temperatures. Impedance spectroscopy is used to separate the bulk conductivity from electrode effect of electrical conductivity data. The bulk dc conductivity is Arrhenius activated, with activation energies and pre-exponential factors following the Meyer–Neldel rule. The real part of ac conductivity shows universal power law feature. The variation of dielectric constant with frequency is attributed to ion diffusion and polarization occurring in the phosphate glasses. The frequency dependent imaginary part of electric modulus M″(ω) plot shows non-Debye feature in conductivity relaxation. The Kohlrausch–Williams–Watts stretched exponential function was used to describe the modulus spectra and the stretching exponent β is found to be temperature independent. Scaling in M″(ω) shows that the electrical relaxation mechanisms are independent of temperature for given composition at different temperatures.     

Structural investigations of nitrided Nb2O5 and Nb2O5–SiO2 sol–gel derived films

Sol–gel derived xNb₂O₅–(100 ? x)SiO₂ films (where x = 100, 80, 60, 50, 40, 20, 0 mol%) were nitrided at various temperatures (800 °C, 900 °C, 1000 °C, 1100 °C and 1200 °C). The structural transformations occurring in the films as a result of ammonolysis were studied using X-ray diffraction (XRD), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The XRD results have shown that the temperatures below 1100 °C were too low to obtain a pure NbN phase in the samples. The AFM observations indicate that the formation of the NbN phase and the size of NbN grains are related to the silica content in the layer. NbN grains become more regular and larger as the niobium content increases. The maximum grain size of about 100 nm was observed for x = 100. Preparation of the Nb₂O₅–SiO₂ sol–gel derived layers and the subsequent nitridation is a promising method of inducing crystalline NbN in amorphous matrices. It follows from the XPS results that a small amount of Nb₂O₅ remains in the films after nitridation at 1200 °C and that nitrogen reacted not only with Nb₂O₅ but also with SiO₂.     

Undoped and calcium doped borate glass system for thermoluminescent dosimeter

Borate glasses present an absorption coefficient very close to that of human tissue. This fact makes some borates ideal materials to develop medical and environmental dosimeters. Glass compositions with calcium tetraborate (CaB₄O₇) and calcium metaborate (CaB₂O₄), such as the xCaB₄O₇ − (100−x)CaB₂O₄ system (0 ⩽ x ⩽ 100 wt%) were obtained by the traditional melting/quenching method. A phenomenon widely known as the ‘boron anomaly’ was observed in our thermal analysis measurements, as indicated by the increase of T_g and the appearance of a maximum value in the composition with 40 wt% of CaB₂O₄. The Dy doped and Li co-doped 80CaB₄O₇–20CaB₂O₄ (wt%) glass samples were studied by the thermoluminescence technique. The addition of Dy improved the signal sensitivity in about three times with respect to the undoped glass sample. The addition of Li as a co-dopant in this glass caused a shift to a lower temperature of about 20 °C in the main glow peak. The structural analysis of the 80CaB₄O₇–20CaB₂O₄ (wt%) undoped and doped samples were studied through infrared absorption. We have noted an increase in the coordination number of the boron atoms from 3 to 4, i.e., the conversion of the BO₃ triangular structural units into BO₄ tetrahedra.     

Structural relaxation and glass transition behavior of novel (Ti33Zr33Hf33)50(Ni50Cu50)40Al10 alloy developed by equiatomic substitution

A series of glass forming alloys (Ti₃₃Zr₃₃Hf₃₃)_100−x−y(Ni₅₀Cu₅₀)_xAl_y (x = 20–70 at.% and y = 0–30 at.%) have been developed by equiatomic substitution of similar elements. Of these alloys (Ti₃₃Zr₃₃Hf₃₃)₅₀(Ni₅₀Cu₅₀)₄₀Al₁₀ was chosen in this study to investigate the structural relaxation and glass transition behavior. The as-quenched (Ti₃₃Zr₃₃Hf₃₃)₅₀(Ni₅₀Cu₅₀)₄₀Al₁₀ alloy was fully amorphous and had a wide supercooled liquid region ΔT = T_x(503 °C) − T_g(433 °C) = 70 °C, where T_g and T_x are the glass transition and crystallization temperatures, respectively. Low temperature pre-heat treatments of the (Ti₃₃Zr₃₃Hf₃₃)₅₀(Ni₅₀Cu₅₀)₄₀Al₁₀ alloy for 10 min at 310 °C, 370 °C and 390 °C caused structural relaxation accompanied by the formation of very fine scale lattice ordering. After these heat treatments, the glass transition became hard to observe in the (Ti₃₃Zr₃₃Hf₃₃)₅₀(Ni₅₀Cu₅₀)₄₀Al₁₀ alloy. Increasing the pre-heat treatment temperatures and holding times caused the glass transition to become more clearly detectable with increasing endothermic heat release.     

Influence of europium ions on structure and crystallization properties of bismuth borate glasses and glass ceramics

Glasses of the xEu₂O₃ · (100?x)[2Bi₂O₃ · B₂O₃] system with 0 ? x ? 25 mol% have been characterized by X-ray diffraction and FTIR spectroscopy measurements. Melting at 1100 °C and the rapid cooling at room temperature permitted us to obtain glass samples. In order to improve the local order and to develop crystalline phases, the glass samples were kept at 625 °C for 24 h. After heat treatment two crystalline phases were put into evidence. One of the crystalline phases was observed for the host glass matrix, the x = 0 mol% sample, and belongs to the cubic system. The second one was observed for the x = 25 mol% sample and was find to be orthorhombic with two unit cell parameters very close to each other. For the samples with 0 < x < 25 mol% there is a mixture of the two mentioned phases. FTIR spectroscopy data suggest that both Bi₂O₃ and B₂O₃ play the glass network former role while the europium ions play the network modifier role in the studied glasses.