Infrared spectra of acetylene–water complexes: C2D2–H2O,C2D2–HDO,and C2D2–D2O

Infrared spectra of C₂D₂–water complexes are studied in the 4.1 μm region of the C₂D₂ ν₃ fundamental band using a tunable diode laser source to probe a pulsed supersonic slit jet. Relatively large vibrational red shifts (?27.7 to ?28.0 cm^?1) are observed which are more easily interpretable than for the analogous C₂H₂ vibration thanks to the absence of Fermi resonance effects for C₂D₂. Noticeable homogeneous line broadening leads to estimates of upper state predissociation lifetimes of about 0.5, 0.9 and 1.1 ns for C₂D₂–H₂O, –HDO, and –D₂O, respectively. Transitions involving K_a = 0 and 1 levels are observed for C₂D₂–HDO, but there is a puzzling absence of K_a = 1 for C₂D₂–H₂O and C₂D₂–D₂O.     

Ultrasound assisted synthesis of TiO2–WO3 heterostructures for the catalytic degradation of Tergitol (NP-9) in water

TiO₂–WO₃ heterostructures were synthesized at room temperature, ambient pressure, and short reaction time via a sonochemical approach. TEM and EDX images show that the prepared TiO₂–WO₃ heterostructures consist of globular agglomerates (∼250 nm in diameter) composed of very small (<5 nm) dense particles (WO₃) dispersed inside the globules. The observed less intense monoclinic WO₃ diffraction peak (around 2θ = 22° belonging to (0 0 1) plane) and the high intense hexagonal WO₃ diffraction peak (around 2θ = 28° belonging to (2 0 0) plane) in XRD indicate that there may be phase transition occurring due to the formation of intimate bond between TiO₂ and WO₃. In addition, the formation of such new phase was also observed from Raman spectra with a new peak at 955 cm⁻¹, which is due to the symmetric stretching of W = O terminal. The catalytic activity of TiO₂–WO₃ heterostructures was tested for the degradation of wastewater pollutant containing Tergitol (NP-9) by a process combined with ozonation and it showed two-fold degradation rate compared with ozone process alone.     

Structure twinning,electronic and photoluminescence properties of yavapaiite-type orthophosphate BaTi(PO4)2

A ternary orthophosphate BaTi(PO₄)₂ has been prepared using a high temperature molten salt method and structurally determined by single crystal X-Ray diffraction analysis. It crystallizes in yavapaiite-type structure with monoclinic space group C2/m. The structure was refined by a non-merohedral twinning model with the twin law (−0.435 1.4350 −0.564 −0.435 0 0.097 −0.099 1). Band structure calculation using the density functional theory (DFT) method indicates that BaTi(PO₄)₂ has a direct bond gap of about 3.00 eV, which is well fitted with the experimental value of 2.95 eV. The photoluminescence excitation and emission spectra, decay curve, and the color coordinates for BaTi(PO₄)₂ were investigated. It can be efficiently excited by UV light (270 nm) and presents blue–green emission (centered at 506 nm), which may be attributed to the lattice defect emission.     

Synthesis,crystal structure,spectroscopic characterization and optical properties of bis(4-acetylanilinium) tetrachlorocobalt (II)

The chemical preparation, crystal structure, spectroscopic investigations and optical features are given for a novel organic–inorganic hybrid material [C₈H₁₀NO]₂CoCl₄.The compound is crystallized in the orthorhombic space group Cmca, with the following unit cell parameters: a=19.461(2) Å, b=15.523(2) Å, c=13.7436(15) Å, and Z=8. The atomic arrangement shows an alternation of organic and inorganic layers along the b-axis. The cohesion between these entities is performed by N–H…Cl and N–H…O hydrogen bonds and π–π stacking interactions.Infrared and Raman spectra at room temperature are recorded in the 4000−400 and 4000−0 cm⁻¹ frequency regions, respectively and analyzed on the basis of literature data. This study confirms the presence of the organic cation [C₈H₁₀NO]⁺ and of the [CoCl₄]²⁻ anion. UV–vis spectroscopy results showed the indirect transition with band gap energy 2.98 eV.     

Transport and magnetic properties of bulk polycrystalline (YBa2Cu3O7)1−x(Nd0.7Sr0.3MnO3)x nanocomposites

We have prepared a series of bulk polycrystalline samples with the nominal compositions (YBa₂Cu₃O₇)_1?x(Nd_0.7Sr_0.3MnO₃)_x (x = 0–1) by a conventional solid-state reaction method using the larger difference in sintering temperature of the two constituent oxides and a well conceived sintering sequence. XRD patterns show that the samples are composites consisting of YBa₂Cu₃O₇ and Nd_0.7Sr_0.3MnO₃ particles with average grain size of ～65 nm. For x ? 0.55, with increasing x, the zero-resistance superconducting transition temperature, T_C0, measured at zero magnetic field decreases and the normal state resistivity increases rapidly. The T_C0 for the sample with x ～ 0.48 is estimated to be 0 K. The M–H hysteresis loops indicate the coexistence of ferromagnetism and superconductivity in the samples. The depression of T_C0 can be attributed to the proximity effect between ferromagnetism and superconductivity.     

Giant magneto-caloric effect around room temperature at moderate low field variation in La0.7(Ca1−xSrx)0.3MnO3 perovskites

Among the perovskite manganites, a series of La_1?xCa_xMnO₃ has the largest magneto-caloric effect (MCE) (|ΔS_m|_max=3.2–6.7 J/kg K at ΔH=13.5 kOe), but the Curie temperatures, T_C, are quite low (165–270 K). The system of LaSrMnO₃ has quite high T_C but its MCE is not so large. The manganites La_0.7(Ca_1?xSr_x)_0.3MnO₃ (x=0, 0.05, 0.10, 0.15, 0.20, 0.25) have been prepared by solid state reaction technique with an expectation of large MCE at room temperature region. The samples are of single phase with orthorhombic structure. The lattice parameters as well as the volume of unit cell are continuously increased with the increase of x due to large Sr²⁺ ions substituted for smaller Ca²⁺ ions. The field-cooled (FC) and zero-field-cooled (ZFC) thermomagnetic measurements at low field and low temperatures indicate that there is a spin-glass like (or cluster glass) state occurred. The Curie temperature T_C increases continuously from 258 K (for x=0) to 293 K (for x=0.25). A large MCE of 5 J/kg K has been observed around 293 K at the magnetic field change ΔH=13.5 kOe for the sample x=0.25. The studied samples can be considered as giant magneto-caloric materials, which is an excellent candidate for magnetic refrigeration at room temperature region.     

High resolution emission spectroscopy of the E2Π–X2Σ+ transition of SrH and SrD

Emission spectra of SrH and SrD have been studied at high resolution using a Fourier transform spectrometer. The molecules have been produced in a high temperature furnace from the reaction of strontium metal vapor with H₂/D₂ in the presence of a slow flow of Ar gas. The spectra observed in the 18 000–19 500 cm^?1 region consist of the 0–0 and 1–1 bands of the E²Π–X²Σ⁺ transition of the two isotopologues. A rotational analysis of these bands has been obtained by combining the present measurements with previously available pure rotation and vibration–rotation measurements for the ground state, and improved spectroscopic constants have been obtained for the E²Π state. The present analysis provides spectroscopic constants for the E²Π state as ΔG(½) = 1166.1011(15) cm^?1, B_e = 3.805503(32) cm^?1, α_e = 0.098880(47) cm^?1, r_e = 2.1083727(89) Å for SrH, and ΔG(½) = 839.1283(23) cm^?1, B_e = 1.918564(15) cm^?1, α_e = 0.034719(23) cm^?1, r_e = 2.1121943(83) Å for SrD.     

Spectroscopic properties of Co2+: ZnAl2O4 nanocrystals in sol–gel derived glass–ceramics

Transparent glass–ceramics containing zinc–aluminum spinel (ZnAl₂O₄) nanocrystals doped with tetrahedrally coordinated Co²⁺ ions were obtained by the sol–gel method for the first time. The gels of composition SiO₂–Al₂O₃–ZnO–CoO were prepared at room temperature and heat-treated at temperature ranging 800–950 °C. When the gel samples were heated up to 900 °C, ZnAl₂O₄ nanocrystals were precipitated. Co²⁺ ions were located in tetrahedral sites in ZnAl₂O₄ nanocrystals. X-ray diffraction analysis shows that the crystallite sizes of ZnAl₂O₄ crystal become large with the heat-treatment temperature and time, and the crystallite diameter is in the range of 10–15 nm. The dependence of the absorption and emission spectra of the samples on heat-treatment temperature were presented. The difference in the luminescence between Co²⁺ doped glass–ceramic and Co²⁺ doped bulk crystal was analysed. The crystal field parameter D_q of 423 cm⁻¹ and the Racah parameters B of 773 cm⁻¹ and C of 3478.5 cm⁻¹ were calculated for tetrahedral Co²⁺ ions.     

Resourceful synthesis of pyrazolo[1,5-a]pyrimidines under ultrasound irradiation

Pyrazolo[1,5-a]pyrimidines were synthesized via the ultrasonic sonochemical method using the cyclocondensation reaction of 4-alkoxy-1,1,1-trifluoro-3-alken-2-ones [CF₃C(O)CH = C(R)(OMe) – where R = Me, Bu, i-Bu, Ph, 4-Me–C₆H₄, 4-F–C₆H₄, 4-Cl–C₆H₄, 4-Br–C₆H₄, naphth-2-yl and biphen-4-yl] – with 3-amino-5-methyl-1H-pyrazole in the presence of EtOH for 5 min. This methodology has several advantages, for example, it is a simple procedure, it has an easy work-up, mild conditions, short reaction times (5 min) and produces satisfactory yields (61–98%).     

Preparation of carbon aerogel in ambient conditions for electrical double-layer capacitor

Carbon aerogels were prepared by polycondensation of resorcinol with formaldehyde using sodium carbonate as a catalyst in ambient conditions, and they were used as an electrode of electrical double-layer capacitor. The effect of resorcinol to catalyst ratio (R/C ratio) on volume shrinkage, BET surface area, and electrochemical property of carbon aerogels was investigated by changing R/C ratio from 50 to 2000. In order to minimize volume shrinkage, solvent exchange was performed with acetone at 50 °C for 1 day. Volume shrinkage was <2% after 2-day gelation in the absence of CO₂ supercritical drying. BET surface area was strongly dependent on R/C ratio. Carbon aerogel prepared at R/C ratio of 500 showed the highest BET surface area (706 m²/g) with average pore diameter of 10.9 nm. Electrochemical property of carbon aerogels as an electrode of electrical double-layer capacitor was investigated by cyclic voltammetry measurement. Specific capacitance of carbon aerogel prepared at R/C ratio of 500 was found to be 81 F/g in 1 M H₂SO₄ electrolyte at the scan rate of 10 mV/s.     

Structural and photoluminescence investigation on the hot-wire assisted plasma enhanced chemical vapor deposition growth silicon nanowires

High density of silicon nanowires (SiNWs) were synthesized by a hot-wire assisted plasma enhanced chemical vapor deposition technique. The structural and optical properties of the as-grown SiNWs prepared at different rf power of 40 and 80 W were analyzed in this study. The SiNWs prepared at rf power of 40 W exhibited highly crystalline structure with a high crystal volume fraction, X_C of ～82% and are surrounded by a thin layer of SiO_x. The NWs show high absorption in the high energy region (E>1.8 eV) and strong photoluminescence at 1.73 to 2.05 eV (red–orange region) with a weak shoulder at 1.65 to 1.73 eV (near IR region). An increase in rf power to 80 W reduced the X_C to ～65% and led to the formation of nanocrystalline Si structures with a crystallite size of <4 nm within the SiNWs. These NWs are covered by a mixture of uncatalyzed amorphous Si layer. The SiNWs prepared at 80 W exhibited a high optical absorption ability above 99% in the broadband range between 220 and ～1500 nm and red emission between 1.65 and 1.95 eV. The interesting light absorption and photoluminescence properties from both SiNWs are discussed in the text.     

Cellulose-based carbon—A potential anode material for lithium-ion battery

A series of hard carbons was produced by the carbonization of microcrystalline cellulose powder in the temperature range of 950–1100 °C. The properties of the carbons were characterized using elemental analysis, X-ray diffraction and N₂ and CO₂ adsorption. The effect of heat-treatment temperature (HTT), pyrolytic carbon (PC) coating and discharging mode on the lithium insertion/deinsertion behavior of the carbons was assessed in a coin-type half-cell with metal lithium cathode. Increasing cellulose HTT modifies mostly carbon porosity, the surface area (S_DFT) decreases from about 500 to 167 m² g⁻¹. It is associated with lowering the reversible C_rev and irreversible C_irr capacities, but without improving relatively low (0.72) 1st cycle coulombic efficiency. Applying constant current (CC)+constant voltage (CV) discharging mode instead of conventional CC enhances the reversible capacity by 15–18%. PC coating is effective in reducing C_irr by ∼20% with a little change of C_rev. The best capacity parameters, C_rev of 458 mA h g⁻¹ and C_irr of 139 mA h g⁻¹, were measured for PC coated 1000 °C carbon. The prolonged cycling of full-cell assembled with anode of the carbon and commercial cathode revealed that after initial 20 cycles the capacity decay (0.029 mA h/cycle) is comparable to that of commercial cell with graphite-based anode.     

Cathodoluminescence studies of un-doped and (Cu,Fe, and Co)-doped tin dioxide films deposited by spray pyrolysis

Un-doped and (Cu, Fe, and Co)-doped SnO₂ were studied using films deposited by spray pyrolysis. Room temperature cathodoluminescence (CL) was measured. Differences in CL spectra were observed as a function of deposition parameters (T_sub-350–550 °C), the nature and concentration of dopants (0–16 at.%), and the resulting high annealing temperature (T_an = 700–950 °C). A possible luminescence mechanism has been discussed. It was established that changes taking place in CL spectra were caused by the change of both the grain size and crystallinity (stoichiometry) of the surface layer. It was concluded that radiative recombination occurs through shallow donor levels associated with O-vacancies and trapped centers. It was assumed that in SnO₂ there are apparently three types of defects forming deep levels located at 0.8–0.9, 1.3–1.4, and ∼1.6 eV from the top of the valence band.     

Enhanced JC in air-processed GdBa2Cu3O7−δ superconductor bulk grown by the additions of nano-particles

Single domain superconductor GdBa₂Cu₃O_7?δ bulks with variable additions of (ZnO + ZrO₂ + SnO₂) nano-particles was prepared in air by using top seed melt-textured growth process. The effect of nano-particle additions on superconductivity properties has been investigated. An enhancement of the critical current J_C in low and intermediate field at 77 K and trapped field was discovered by the additions of the nano-particles. At the same time, the superconductor transition temperature, T_C, slightly decreases from 93.5 K to 91.5 K. The experimental results show that the accumulation of the nano-particle inclusions may improve J_C of the specimens.     

High-pressure dielectric studies of a novel hydrogen-bonded ferroelectric (NH4)2H2P2O6

The hydrostatic pressure effect on the dielectric properties of (NH₄)₂H₂P₂O₆ ferroelectric crystal was studied for pressures from 0.1 MPa to 360 MPa and for temperatures from 100 to 190 K. The pressure–temperature phase diagram obtained is linear with increasing pressure. The paraelectric–ferroelectric phase transition temperature decreases with increasing pressure with the pressure coefficient dT_c/dp=?5.16×10^?2 K MPa^?1. Additionally, the pressure dependences of Curie–Weiss constants for the crystal in paraelectric (C₊) and ferroelectric (C_?) phases are evaluated and discussed. The possible mechanism of paraelectric–ferroelectric phase transition is also discussed.     

Concentration influence on temperature-dependent luminescence properties of samarium substituted strontium tetraborate

The series of divalent samarium substituted strontium tetraborate (Sr_1?xSm_xB₄O₇) polycrystalline samples were prepared by the conventional solid-state reaction. The phase formation of the samples was investigated by X-ray powder diffraction measurements. The luminescence spectra and decay curves of the Sm²⁺ ions were measured. Temperature dependent Sm²⁺ luminescence properties were investigated. The f–d and ⁵D₁–⁷F_J transitions appeared at 350 K and increased with increase in the temperature while the intensity of ⁵D₀–⁷F_J transitions decreased. The emission spectra pointed out that Sm²⁺ occupies of C_2v or lower symmetry site. The photoluminescence decay times of strontium tetraborate doped with different concentrations of Sm²⁺ was investigated as a function of temperature in the range of 100–500 K. However, no obvious concentration quenching was observed.     

Effect of Fe doping on the room temperature ferromagnetism in chemically synthesized (In1−xFex)2O3 (0 ⩽ x ⩽ 0.07) magnetic semiconductors

Observation of room temperature ferromagnetism in Fe doped In₂O₃ samples (In_1−xFe_x)₂O₃ (0 ⩽ x ⩽ 0.07) prepared by co-precipitation technique is reported. Lattice parameter obtained from powder X software shows distinct shrinkage of the lattice constant indicating an actual incorporation of Fe ions into the In₂O₃ lattice. X-ray diffraction data measurements show that the entire sample exhibits single phase polycrystalline behavior. SEM micrographs showed the prepared powder was in the range 25–36 nm. SEM EDS mapping showed the presence of Fe and In ions in the Fe doped In₂O₃ sample. The highest remanence magnetization moment (6.624 × 10⁻⁴ emu/g) is reached in the sample with x = 0.03.     

High performance GdBa2Cu3O7−z film preparation by non-fluorine chemical solution deposition approach

Biaxially textured GdBa₂Cu₃O_7?z (GdBCO) films with T_c above 93 K have been prepared on (0 0 l) LaAlO₃ substrate by self-developed non-fluorine polymer-assisted chemical solution deposition (PA-CSD) approach. The GdBCO films show smooth and crack-free morphology. Many nanoscale particles with homogeneous distribution are observed in the GdBCO films, which have not been observed yet in the YBa₂Cu₃O_7?z (YBCO) films prepared by the same processing technique. Besides a high J_c (77 K, 0 T) of 2.28 MA/cm², the optimized GdBCO films show a better J_c–B behavior and an improved high-field J_c, compared to the YBCO films.     

Synthesis and characterization of nanocrystalline HAp powders prepared by using aloe vera plant extracted solution

Nanocrystalline hydroxyapatite (HAp) powders were synthesized by a simple method using aloe vera plant extracted solution. To obtain nanocrystalline HAp, the prepared precursor was calcined in air at 400–800 °C for 2 h. The phase composition of the calcined samples was studied by X-ray diffraction (XRD) technique. The XRD results confirmed the formation of HAp phase. With increasing calcination temperature, the crystallite of the HAp increased, showing the hexagonal structure of HAp with the lattice parameter, a, in a range of 0.9520–0.9536 nm and c of 0.6739–0.6928 nm. The particle sizes of the powder were obtained to be 43–171 nm. The optical properties of the calcined powders were characterized by Raman and FTIR spectroscopies. The Raman spectra showed a main peak of the phosphate vibration mode (ν₁(PO₄)) at ∼963 cm⁻¹ for all the calcined samples. The peaks of the phosphate carbonate and hydroxyl vibration modes were observed in the FTIR spectra for all the calcined powders. The morphology tends to change from a spherical shape to a rod-like shape with increasing calcination temperature as revealed by TEM.     

Rotational analysis of bands in the high-resolution infrared spectra of cis,cis- and trans,trans-1,4-difluorobutadiene-2-d1

Pure samples of cis,cis- and trans,trans-1,4-difluorobutadiene-2-d₁ have been synthesized, and high-resolution (0.0015 cm^?1) infrared spectra have been recorded for these nonpolar molecules in the gas phase. For the cis,cis isomer, the rotational structure in two C-type bands at 775 and 666 cm^?1 and one A-type band at 866 cm^?1 has been analyzed to yield a combined set of 2020 ground state combination differences (GSCDs). Ground state rotational constants fit to these GSCDs are A₀ = 0.4195790(4), B₀ = 0.0536508(8), and C₀ = 0.0475802(9) cm^?1. For the trans,trans isomer, three C-type bands at 856, 839, and 709 cm^?1 have been investigated to give a combined set of 1624 GSCDs. Resulting ground state rotational constants for this isomer are A₀ = 0.9390117(8), B₀ = 0.0389225(4), and C₀ = 0.0373778(3) cm^?1. Small inertial defects confirm the planarity of both isomers in the ground state. Upper state rotational constants have been determined for most of the transitions. The ground state rotational constants for the two isotopologues will contribute to the data set needed for determining semiexperimental equilibrium structures for the nonpolar isomers of 1,4-difluorobutadiene.