Electrical and mechanical properties of proton conducting SrCe0.95Yb0.05O3 − α

Yb³⁺-doped ceramic strontium cerate of exactly the composition SrCe_0.95Yb_0.05O_{3 − α} was prepared, having a relative density of 99.0 (± 0.3%). Great care was taken to obtain homogeneous, carbonate free material. Analysis are made of the X-ray powder diffraction pattern of the as-prepared dense ceramic, resulting in the orthorhombic unit cell parameters a = 6.997(2) Å, b = 12.296(3) Å, c = 8.588(2) Å, Z = 8 and d_x = 5.806(2) g cm⁻³. Bending strength values of the ceramic in non-proton and proton conducting state are found to be 177 and 194 MPa respectively. The ceramic kept under proton conducting conditions for 500 h at 300 °C to 800 °C in a N₂ flow containing 155 mbar water vapour and 245 mbar H₂, have shown to remain chemically and structurally stable. Impedance spectroscopy measurements of the bulk conductivity of the proton conducting ceramic revealed an activation energy of 53.2 kJ mol⁻¹ and a preexponential factor of 359.1 (Ω cm)⁻¹ K. In the non-proton conducting state the ceramic is mainly oxygen ion vacancy conducting, which indicates that charge compensation on substituting Yb⁺³ in SrCeO₃ takes place by oxygen ion vacancies.     

Angular distribution measurements of Li(p,α)He reaction at 140 keV proton energy using nuclear track detectors

Angular distributions of a ⁶Li(p,α) ³He reaction were measured at six angles for 140 keV proton energy using nuclear track detectors (NTDs). The measurements were carried out over 60°–160° lab. angles in 20° increments using a scattering chamber of 80° beam line of the 350 kV accelerator. A semiconductor silicon surface barrier (SSB) detector was placed at +160° and was used as a monitor. The results have shown that the CR-39 detector has excellent capabilities to distinguish 1.4–2.7 MeV α+ ³He particles from the ⁶Li(p,α) ³He reaction and 8–9.4 MeV α-particles from the ⁷Li(p,α) ⁴He reaction through their track diameters. However, it was not possible to distinguish between the 2.3 MeV ³He ions and the 1.7 MeV ⁴He ions from the ⁶Li(p,α) ³He reaction from their track diameter measurements, but it was possible to differentiate between the two, from the darker contrast of the ³He particles caused by its deeper tracks as compared to those of ⁴He.     

The harmonic force field and ground-state average structure of difluoroborane

An improved harmonic force field of difluoroborane has been calculated using the vibrational wavenumbers and quartic centrifugal distortion constants of four isotopic species. The unidentified vibrational mode ν₅ is predicted at 1049 ± 50 and 775 ± 50 cm⁻¹ for HBF₂ and DBF₂, respectively. The ground-state average structure of HBF₂ has been found to be r_z(BH) = 1.195 ± 0.003 Å; r_z(BF) = 1.315 ± 0.001 Å; (FBF) = 118.0 ± 0.1°.     

Lorentz-mikroskopie von Bloch- und Néelwänden in Ni-Fe-kristallen

We prepared thin single crystal foils of 50 Ni 50 Fe for observation in a 100 kV electron microscope. Due to its high saturation induction and low anisotropy, magnetic domain walls can be easily observed in this material. The effective anisotropy which governs the wall angles consists of crystal anisotropy and superimposed random stress anistropies so that wall angles of any magnitude are found.In accordance with theory three distinct wall types are identified for film thickness between 500 Å and 2000 Å as a function of wall angle θ: (i) the asymmetric Bloch wall for 180° θ #62; 140°, (ii) the asymmetric Néel wall for 140° #62; θ #62; θ_s, and (iii) the symmetric Néel wall for θ_s #62; θ, where θ_s is an angle which decreases with increasing film thickness.     

New ferromagnetic La3Co2TaO9 double perovskite: Structural and magnetic properties

The new double perovskite La₃Co₂TaO₉ has been prepared by a solid-state procedure. The crystal and magnetic structures have been studied from X-ray powder diffraction (XRPD) and neutron powder diffraction (NPD) data. Rietveld refinements were performed in the monoclinic space group P2₁/n. The structure consists of an ordered array of alternating B′O₆ and B″O₆ octahedra sharing corners, tilted along the three pseudocubic axes according to the Glazer notation a⁻b⁻c⁺. Rietveld refinements show that at RT the cell parameters are a=5.6005(7) Å, b=5.6931(7) Å, c=7.9429(9) Å and β=89.9539(7)°, and the refined crystallographic formula of this “double perovskite” can be written as La₂(Co)_2d(Co_1/3Ta_2/3)_2cO₆. Magnetization measurements and low-temperature NPD data show that the perovskite is a ferromagnet with T_C=72 K. At high T it follows the Curie–Weiss law with an effective magnetic moment of 3.82μ_B per Co ion which is very close to spin only Co²⁺ (HS).     

Doppler-limited dye laser excitation spectroscopy of DCF

The dye laser excitation spectrum of the vibronic transition of DCF was observed between 17 200 and 17 400 cm⁻¹ with the Doppler-limited resolution. DCF was produced by the reaction of microwave-discharged CF₄ with CD₃F. The observed spectra, which were found to be nearly free of perturbations, were assigned to 858 transitions of the K′_a − K″_a = 4−5, 3−4, 2−3, 1−2, 0−1, 1−0, 2−1, 3−2, 3−3, 2−2, 1−1, 0−0, 2−0, and 0−2 subbands, and were analyzed to determine the rotational constants and centrifugal distortion constants for both the and à states. The rotational constants of DCF thus determined were combined with those of HCF to calculate the structural parameters for this molecule: r(C---H) = 1.138 Å, r(C---F) = 1.305 Å, and HCF = 104.1° for the ground state, and r(C---H) = 1.063 Å, r(C---F) = 1.308 Å, and HCF = 123.8° for the excited à state.     

The microwave spectrum of phosphabutadiyne, H---CC---CP

A detailed rotational analysis of the microwave spectrum between 26.5 and 40 GHz of phosphaethene, CH₂=PH, has been carried out. This molecule is the simplest member of a new class of unstable molecules—the phosphaalkenes. The species can be produced by pyrolysis of (CH₃)₂PH, CH₃PH₂ and also somewhat more efficiently from Si(CH₃)₃CH₂PH₂. Full first-order centrifugal distortion analyses have been carried out for both ¹²CH₂³¹PH and ¹²CH₂³¹PD yielding: A₀ = 138 503.20(21), B₀ = 16 418.105(26), and C₀ = 14 649.084(28) MHz for ¹²CH₂³¹PH. The 1₀₁-0₀₀ μ_A lines have also been detected for ¹³CH₂PH, cis-CDHPH and trans-CHDPH. These data have enabled an accurate structure determination to be carried out which indicates: r(H_cC) = 1.09 ± 0.015 Å, (H_cCP) = 124.4 ± 0.8°; r(H_tC) = 1.09 ± 0.015 Å, (H_tCP) = 118.4 ± 1.2°; r(CP) = 1.673 ± 0.002 Å, (HCH) = 117.2 ± 1.2°; r(PH) = 1.420 ± 0.006 Å, (CPH) = 97.4 ± 0.4°. The dipole moment components have been determined as μ_A = 0.731 (2), μ_B = 0.470 (3), μ = 0.869 (3) D for CH₂PH; μ_A = 0.710 (2), μ_B = 0.509 (10), μ = 0.874 (7) D for CH₂PD.     

Surface structures of in (√3 × √3 )R30° and (5√3 × 2) phases studied by surface extended X-ray absorption fine structure spectroscopy

The local surface structures of in the ( √3 × √3) R30° and (5√3 × 2) phases have been investigated by means of polarization-dependent sulfur K-edge surface EXAFS. In the (√3 × √3 ) R30° phase, sulfur adatoms are found to occupy threefold hollow sites with a S---Ni distance of 2.13 Å and an inclination angle ω of the Sz.sbnd;Ni bonds at 44° from the surface plane. In contrast, in the (5√3 × 2) phase, it is determined that the Sz.sbnd;Ni bond is longer, 2.18 Å, more inclined, ω = 31°, and that the coordination number is not 3 but 4. These results strongly support a picture involving reconstruction of the top nickel layer to form a rectangular structure. Consideration of several models proposed for the (5√3 × 2) phase leads to one which is compatible with both the present results and results recently reported using STM.     

The ZnO non-polar (10 0) surface: an X-ray structural investigation

We performed a structural analysis of the non-polar ZnO (10 0) surface by means of grazing incidence X-ray diffraction. The analysis was conducted on ten rods, smooth surface domains, though of small coherent width, having been obtained after several Ar⁺ sputtering–annealing cycles. The surface derived from the bulk structure exposes one ZnO dimer per unit cell, parallel to the [001] axis. All the existing models, derived from ab initio calculations or low-energy electron diffraction (LEED) analyses, consist in a surface dimer whose O and Zn atoms are shifted inwards, with the O pointing outwards with respect to Zn. Whereas the LEED studies conclude on a dimer distance greater than in the bulk, the theoretical studies agree on a dimer contracted by amounts ranging from 5.5 to 7.5%. This contraction is interpreted as a result of the strong ionicity of ZnO, and is associated with a moderate dimer rotation. The latter, however, is found between 2.3 and 11.4°. Despite the discrepancies between the models, the Zn atom is always found shifted downwards by more than 0.25 Å. This is unambiguously rejected by our data, which show that the Zn atom keeps very close to its bulk position. It is displaced downwards by ΔZ_Zn=−0.06±0.02 Å, and it moves along [001] towards O by ΔX_Zn=0.05±0.02 Å. We denote a trend for the O atom to be displaced downwards too, with a concomitant displacement towards Zn. The faint X-ray scattering of O prevents us from assessing its position with accuracy. Depending on the choice of position for Zn in the error bar range, the buckling is evaluated as between −6.5 and 3°, or between −4 and 0.5°. The dimer distance is evaluated equal to 1.90 Å, with a deviation equal either to 0.06 or 0.11 Å.     

Rotational Spectra of CH2DCCH and CH3CCD: Experimental and ab Initio Equilibrium Structures of Propyne

The ground state rotational spectra of CH₂DCCH and CH₃CCD (main species and ¹³C-substituted species) have been measured up to 470 GHz. Accurate rotational and centrifugal distortion constants have been determined. r₀, r_s, r_ε,I, and r^ρ_m, structures of propyne have been calculated. The ab initio structure has also been calculated using three different methods (SCF, MP2, and QCISD) and two basis sets (DZP and TZ2P). Offsets have been derived empirically using molecules containing structural units present in propyne and whose equilibrium structures have been determined previously. A near-equilibrium structure has been estimated to be acetylenic r(C---H) = 1.061 (1) Å, r(CC) = 1.204 (1) Å, r(C---C) = l.458 (2) Å, methyl r(C---H) = 1.089 (1) Å, and (CCH) = 110.7 (5)°.     

Magnetic order in CaMn2Sb2 studied via powder neutron diffraction

This paper reports a neutron powder diffraction study of CaMn₂Sb₂ in the temperature range of 20–300 K. Collinear long-range antiferromagnetic order of manganese ions occurs below 85 K, where a transition is observed in the dc magnetic susceptibility measured with a single crystal. Short-range magnetic order, characterized by a broad diffraction peak corresponding to a d-spacing of approximately 4 Å (2θ≈22°), is also observed above 20 K. The long-range antiferromagnetic order is indexed by the chemical unit cell, indicating a propagation vector k=(0 0 0), with a refined magnetic moment of 3.38 μ_B at 20 K. Two possible magnetic models have been identified, which differ in spin orientation for the two manganese ions with respect to the ab plane. The model with spins oriented at a 25±2° angle relative to the ab plane gives an improved fit compared to the other model in which the spins are constrained to the ab plane. Representational analysis can account for a model involving a c-axis component only by the mixing of two irreducible representations.     

CHHC and H–H magnetization exchange: Analysis by experimental solid-state NMR and 11-spin density-matrix simulations

A protocol is presented for correcting the effect of non-specific cross-polarization in CHHC solid-state MAS NMR experiments, thus allowing the recovery of the ¹H–¹H magnetization exchange functions from the mixing-time dependent buildup of experimental CHHC peak intensity. The presented protocol also incorporates a scaling procedure to take into account the effect of multiplicity of a CH₂ or CH₃ moiety. Experimental CHHC buildup curves are presented for l-tyrosine·HCl samples where either all or only one in 10 molecules are U–¹³C labeled. Good agreement between experiment and 11-spin SPINEVOLUTION simulation (including only isotropic ¹H chemical shifts) is demonstrated for the initial buildup (t_mix < 100 μs) of CHHC peak intensity corresponding to an intramolecular close (2.5 Å) H–H proximity. Differences in the initial CHHC buildup are observed between the one in 10 dilute and 100% samples for cases where there is a close intermolecular H–H proximity in addition to a close intramolecular H–H proximity. For the dilute sample, CHHC cross-peak intensities tended to significantly lower values for long mixing times (500 μs) as compared to the 100% sample. This difference is explained as being due to the dependence of the limiting total magnetization on the ratio N_obs/N_tot between the number of protons that are directly attached to a ¹³C nucleus and hence contribute significantly to the observed ¹³C CHHC NMR signal, and the total number of ¹H spins into the system. ¹H–¹H magnetization exchange curves extracted from CHHC spectra for the 100% l-tyrosine·HCl sample exhibit a clear sensitivity to the root sum squared dipolar coupling, with fast buildup being observed for the shortest intramolecular distances (2.5 Å) and slower, yet observable buildup for the longer intermolecular distances (up to 5 Å).     

The microwave spectrum, structure, and barrier to internal rotation of selenoacetaldehyde, CH3CHSe

The rotational spectrum of the unstable molecule selenoacetaldehyde, CH₃CHSe, has been studied by microwave spectroscopy between 26.5 and 40 GHz. Transitions have been measured for five abundant selenium isotopic variants. These measurements have, together with structural information from the related molecules CH₃CHS and CH₃CHO, allowed reliable data on the C=Se bond length (1.758 ± 0.01 Å) and the e angle (125.7 ± 0.3°) to be derived. The spectral lines show splittings due to hindered internal rotation and using these together with the derived structure, barrier heights of 1602 cal mole⁻¹ (6703 J mole⁻¹) and 1648 cal mole⁻¹ (6859 J mole⁻¹) have been determined for the ground and first torsionally excited states, respectively.     

On search and identification of tracks due to short-lived SHE nuclei in extraterrestrial crystals

The unique approach for search and unambiguous identification of short-lived (T_1/2=10³–10⁷ years) superheavy nuclei in cosmic-ray products of the recent nucleosynthesis in our Galaxy are discussed.It is based on: (a) the ability of non-conducting crystals to register and to store for many million years the tracks due to fast nuclei with atomic number Z20 (“fossil” tracks);(b) calibrations of the said crystals with accelerated heavy ions (20Z92) and on revealing the volume etchable track length (VETL) of the fast nuclei coming to rest inside crystals—both of fossil and “fresh” tracks—to determine the charge distribution of cosmic-ray nuclei tracks and(c) the so-called “four-zone” model of tracks in crystals (and also glasses) which provides not only the VETL track length dependence for 20Z92 nuclei but also demonstrates the regular annealing behavior of VETL of 20Z92 nuclei in a broad temperature interval.This approach was first applied in the early 1980s to investigate the “fossil” tracks due to 22Z92 cosmic-ray nuclei in olivine crystals from meteorites-pallasite Marjalahti and Eagle Station.The discovery of Th–U cosmic-ray nuclei tracks in 1980 was unambiguously confirmed by calibrations of the same crystals with ²³⁸U, ¹⁹⁷Au and ²⁰⁸Pb accelerated ions in the late 1980s. More than 1600 tracks due to cosmic-ray actinide nuclei were measured during the last two decades of the 20th century.Also, 11 anomalously long tracks (track length exceeds by a factor (1.6±0.1) the track length due to Th–U nuclei were measured. The detailed analysis shows that at least 5 of these tracks could not be attributed to the Th–U nuclei. It means that now we have a preliminary proof on the existence Z110 nuclei in cosmic-rays. The abundance is Z110/Th–U=(1–3)×10⁻³ in Z110 freshly formed cosmic-rays (time interval 10³–10⁷ years).The method proposed can provide the necessary and sufficient conditions for the discovery of Z110 nuclei in nature.     

The microwave spectrum of 1-phosphabut-3-ene-1-yne, CH2=CHCP

The new molecule 1-phosphabut-3-ene-1-yne, CH₂=CHCP, produced by pyrolyzing prop-1-ene-3-phosphorus dichloride, CH₂=CHCH₂PCl₂, was detected by microwave spectroscopy. The analysis of the rotational transitions indicates that the molecule is planar with constants: A₀ = 46 694(24), B₀ = 2807.7100(21), and C₀ = 2645.8356(21) MHz. These rotational constants indicate that the structure of the vinyl group is essentially the same as that in CH₂=CHCN and CH₂=CHCCH; r(C---C) = 1.432 Å and (C=C---C) = 123.9°. The dipole moment parameters are μ_A = 1.181(2), μ_B = 0.074(1), and μ = 1.183(2) D. The vibrational satellite spectra for the C---CP bending modes indicate that ν₁₁(a′) = 184 ± 30 cm⁻¹ and ν₁₅(a″) = 263 ± 30 cm⁻¹.     

Investigation by EELS and TRIM simulation method of the interaction of Ar and N ions with the InP compound

In this study, the EELS results revealed the great sensitivity of InP compound submitted to Ar⁺ or N⁺ ions at low energy. The preliminary treatment of InP by the Ar⁺ ions was useful as part of the cleaning process of the surface. Further argon ions bombardment on cleaned InP led however to breaking of chemical bonds In–P, with desorption of phosphorus atoms and appearance of In metal distributed on InP. The damaged InP by Ar⁺ ions, constituted the diphase (In; InP) system of depth of about 30 Å, involving a superficial roughness. The In metal proportion on such a system was determined by a calculation method based on the experimental EELS spectra of pure In and InP.We submitted the heated and no heated system (In; InP) to nitrogen ions bombardment. The nitrogen reacted with the In metal to compensate the phosphorus vacancies so that InN species were formed. The heating of (In; InP) system at 450 °C, allowed the surface reconstruction with elimination of defects due to the structure and the roughness. The temperature also caused the coalescence of In metal towards the surface. Because of the physical stability of the interface of heated (In; InP) system, the nitrogen reacted with the outmost layers of In metal to form a homogeneous layer of InN of thickness estimated at 20 Å. We associated to the EELS the TRIM (Transport and Range of Ions in Matter) simulation method in order to show the mechanism of interaction Ar⁺ or N⁺ ions-InP and determine the disturbed depth as a function of the energy. The EELS alone was not able to give us with accuracy the disturbed depth of the target by these ions.     

Carbon-13 and Fluorine-19 NMR Spectroscopy of the Supramolecular Solid p-tert-Butylcalix[4]arene ·α,α,α-trifluorotoluene

The supramolecular 1 : 1 host–guest inclusion compound, p-tert-butylcalix[4]arene ·α,α,α-trifluorotoluene, 1, is characterized by ¹⁹F and ¹³C solid-state NMR spectroscopy. Whereas the ¹³C NMR spectra are easily interpreted in the context of earlier work on similar host–guest compounds, the ¹⁹F NMR spectra of solid 1 are, initially, more difficult to understand. The ¹⁹F{¹H} NMR spectrum obtained under cross-polarization and magic-angle spinning conditions shows a single isotropic resonance with a significant spinning sideband manifold. The static ¹⁹F{¹H} CP NMR spectrum consists of a powder pattern dominated by the contributions of the anisotropic chemical shift and the homonuclear dipolar interactions. The ¹⁹F MREV-8 experiment, which minimizes the ¹⁹F–¹⁹F dipolar contribution, helps to identify the chemical shift contribution as an axial lineshape. The full static ¹⁹F{¹H} CP NMR spectrum is analysed using subspectral analysis and subsequently simulated as a function of the ¹⁹F–¹⁹F internuclear distance (D_FF = 2.25 ± 0.01 Å) of the rapidly rotating CF₃ group without including contributions from additional libration motions and the anisotropy in the scalar tensor. The shielding span is found to be 56 ppm. The width of the centerband in the ¹⁹F{¹H} sample-spinning CP NMR spectrum is very sensitive to the angle between the rotor and the magnetic field. Compound 1 is thus an attractive standard for setting the magic angle for NMR probes containing a fluorine channel with a proton-decoupling facility.     

N Chemical Shift Tensor Magnitude and Orientation in the Molecular Frame of Uracil Determined via MAS NMR

The potential of heteronuclear MAS NMR spectroscopy for the characterization of ¹⁵N chemical shift (CS) tensors in multiply labeled systems has been illustrated, in one of the first studies of this type, by a measurement of the chemical shift tensor magnitude and orientation in the molecular frame for the two ¹⁵N sites of uracil. Employing polycrystalline samples of ¹⁵N₂ and 2-¹³C,¹⁵N₂-labeled uracil, we have measured, via ¹⁵N–¹³C REDOR and ¹⁵N–¹H dipolar-shift experiments, the polar and azimuthal angles (θ, ψ) of orientation of the ¹⁵N–¹³C and ¹⁵N–¹H dipolar vectors in the ¹⁵N CS tensor frame. The (θ_NC, ψ_NC) angles are determined to be (92 ± 10°, 100 ± 5°) and (132 ± 3°, 88 ± 10°) for the N1 and N3 sites, respectively. Similarly, (θ_NH, ψ_NH) are found to be (15 ± 5°, −80 ± 10°) and (15 ± 5°, 90 ± 10°) for the N1 and N3 sites, respectively. These results obtained based only on MAS NMR measurements have been compared with the data reported in the literature.     

Detection and Characterization of Boric Acid and Borate Ion Binding to Cytochrome c Using Multiple Quantum Filtered NMR

The application of multiple quantum filtered (MQF) NMR to the identification and characterization of the binding of ligands containing quadrupolar nuclei to proteins is demonstrated. Using relaxation times measured by MQF NMR multiple binding of boric acid and borate ion to ferri and ferrocytochrome c was detected. Borate ion was found to have two different binding sites. One of them was in slow exchange, k_diss = 20 ± 3 s⁻¹ at 5°C and D₂O solution, in agreement with previous findings by ¹H NMR (G. Taler et al., 1998, Inorg. Chim. Acta 273, 388–392). The triple quantum relaxation of the borate in this site was found to be governed by dipolar interaction corresponding to an average B–H distance of 2.06 ± 0.07 Å. Other, fast exchanging sites for borate and boric acid could be detected only by MQF NMR. The binding equilibrium constants at these sites at pH 9.7 were found to be 1800 ± 200 M⁻¹ and 2.6 ± 1.5 M⁻¹ for the borate ion and boric acid, respectively. Thus, detection of binding by MQF NMR proved to be sensitive to fast exchanging ligands as well as to very weak binding that could not be detected using conventional methods.     

The microwave spectrum, structure, chlorine nuclear quadrupole coupling constants, dipole moment, and centrifugal distortion constants of dichlorosilane

The microwave spectra of three isotopic species of dichlorosilane, SiH₂Cl₂, in its ground vibrational state, have been measured in the frequency region 8–40 GHz. The spectra have yielded values for the rotational constants, centrifugal distortion constants, and chlorine nuclear quadrupole coupling constants, as well as the molecular dipole moment, 1.13 ± 0.02 D. The molecule has C_2v symmetry, and the bond lengths and angles r(Si---Cl=2.033±Å, r(Si---H)=1.480±0.015Å, (Cl---Si---Cl)=109°43′±20±, (H---Si---H)=111°18′±40′ The centrifugal distortion constants have been compared with those calculated using a published force field.