Electron transport analysis for improvement of solid-state dye-sensitized solar cells using poly(3,4-ethylenedioxythiophene) as hole conductors

Dye-sensitized solar cells (DSCs) using solid-state hole conductor, poly(3,4-ethylenedioxythiophene) (PEDOT), were fabricated using in-situ photoelectrochemical polymerization giving short-circuit photocurrent density of 3.20 mA cm-2, open-circuit voltage of 0.77 V, and fill factor of 0.50, and the resulting overall conversion efficiency of 1.25% on average under air mass 1.5 conditions. Furthermore, the electron transport properties of the DSCs based on PEDOT (PEDOT/DSCs) were analyzed using light intensity modulation induced photocurrent and photovoltage decay (SLIM-PCV) measurements and electrochemical impedance spectroscopy (EIS) measurements, and then compared to those of the DSCs based on organic liquid electrolyte containing I-/I3- as redox couple (liquid iodide/iodine electrolyte-DSCs, iodide/DSCs for short). The effective filling of PEDOT in the mesopores of dyed TiO2 layers is an important key to achieve the respectable conversion efficiency of PEDOT/DSCs that is comparable with iodide/DSCs.     

Room temperature polymerization of poly(3,4‐ethylenedioxythiophene) as transparent counter electrodes for dye‐sensitized solar cells

Poly(3,4‐ethylenedioxythiophene) (PEDOT) counter electrode is prepared with in situ polymerization of 3,4‐ethylenedioxythiophene on a fluorine‐doped tin oxide over‐layer glass at room temperature. The cyclic voltammetry, electrochemical impedance spectroscopy, and Tafel polarization are measured to evaluate the catalytic activity of PEDOT counter electrode for I₃^?/I^? redox couple. Comparing the data with that of traditional thermal decomposed Pt counter electrode, it is found that PEDOT has higher catalytic activity than that of Pt counterpart. Power conversion efficiency of the dye‐sensitized solar cell (DSC) with PEDOT counter electrode can attain to 7.713%, a little higher than that of the cell with Pt counter electrode (7.300%). Taking the advantage of high transparency of PEDOT counter electrode, an Ag mirror is put on the back side of PEDOT counter electrode of the DSC to reflect light back for power conversion. Power conversion efficiency of the DSC with this special structure can be further enhanced to 8.359%, which mainly stems from the improved short‐circuit current density by the increased irradiated light intensity. Copyright © 2014 John Wiley & Sons, Ltd.     

High-efficiency organic dye-sensitized mesoscopic solar cells with a copper redox shuttle

Based upon the bis(2,9-dimethyl-1,10-phenanthroline)copper(I/II) electron mediator, we present an iodine-free dye-sensitized solar cell exhibiting an impressive power conversion efficiency of 7.0% at 100 mW cm(-2) air mass global (AM1.5G) conditions, which rivals that of a control cell with a conventional iodine redox couple.     

An iodine-free electrolyte based on ionic liquid polymers for all-solid-state dye-sensitized solar cells

An ionic liquid polymer, poly (1-alkyl-3-(acryloyloxy)hexylimidazolium iodide), was employed as an iodine-free electrolyte in all-solid-state dye-sensitized solar cells with an overall conversion efficiency of 5.29% under AM 1.5 simulated solar light (100 mW cm(-2)) illumination.     

Nanopatterning of mesoporous inorganic oxide films for efficient light harvesting of dye-sensitized solar cells

Nanopatterning provides facile process to well-arrayed mesoporous inorganic oxide films at low cost by using readily available pastes and elastomeric nanostamps. The fabricated nanopattern boosted the light-harvesting efficiency of dye-sensitized solar cells (DSSCs) by a light-trapping technique. The iodine-free solid-state DSSCs showed a 40 % increase in the current density and high efficiency (7.03 %).     

Solid-state dye-sensitized solar cells fabricated by coupling photoelectrochemically deposited poly(3,4-ethylenedioxythiophene) (PEDOT) with silver-paint on cathode

A PEDOT-based dye-sensitized solar cell (DSC) is successfully improved by coupling photoelectrochemically deposited PEDOT layer with an Ag paste-paint on the cathode. With a 9.3 μm thick mesoscopic nanocrystalline TiO(2) film, a maximum cell performance of 3.2% with relatively high V(oc) of around 780 mV is achieved.     

Engineering organic sensitizers for iodine-free dye-sensitized solar cells: red-shifted current response concomitant with attenuated charge recombination

With a new metal-free donor-acceptor photosensitizer featuring the 2,6-bis(thiophen-2-yl)-4,4-dihexyl-4H-cyclopenta[2,1-b:3,4-b']dithiophene-conjugated spacer and the tris(1,10-phenanthroline)cobalt(II/III) redox shuttle, we present a highly efficient iodine-free dye-sensitized solar cell displaying a power conversion efficiency of 9.4% measured at 100 mW cm(-2) simulated AM1.5 conditions.     

左旋多巴和N,N-二甲基亚砜共掺杂PEDOT:PSS作为空穴传输层的高性能p-i-n型钙钛矿太阳能电池

在p-i-n型的钙钛矿太阳能电池中,聚3, 4-乙烯二氧噻吩：聚苯乙烯磺酸盐(PEDOT:PSS)作为最常用的空穴传输层(HTL)材料之一,由于其存在着吸湿性强以及能级与钙钛矿层不匹配等缺点,限制了它的应用。基于此,本文拟采用将左旋多巴(DOPA)和N, N-二甲基亚砜(DMSO)共同掺杂于PEDOT:PSS作为HTL的简单方法制备高性能p-i-n型钙钛矿太阳能电池。研究结果表明,DOPA和DMSO共掺杂PEDOT:PSS可以有效的调节HTL的能级并提高其导电性,器件的能量转化效率由13.35%显著提高到了17.54%。进一步研究发现,相比于未掺杂或单一掺杂的PEDOT:PSS,在DOPA和DMSO共掺杂的PEDOT:PSS上更有利于生长大尺寸、高结晶度的钙钛矿晶体;同时稳态/瞬态荧光和交流阻抗测试表明器件的内部载流子分离和传输更加有效。     

Economical Pt-free catalysts for counter electrodes of dye-sensitized solar cells

Three classes (carbides, nitrides and oxides) of nanoscaled early-transition-metal catalysts have been proposed to replace the expensive Pt catalyst as counter electrodes (CEs) in dye-sensitized solar cells (DSCs). Of these catalysts, Cr(3)C(2), CrN, VC(N), VN, TiC, TiC(N), TiN, and V(2)O(3) all showed excellent catalytic activity for the reduction of I(3)(-) to I(-) in the electrolyte. Further, VC embedded in mesoporous carbon (VC-MC) was prepared through in situ synthesis. The I(3)(-)/I(-) DSC based on the VC-MC CE reached a high power conversion efficiency (PCE) of 7.63%, comparable to the photovoltaic performance of the DSC using a Pt CE (7.50%). In addition, the carbide catalysts demonstrated catalytic activity higher than that of Pt for the regeneration of a new organic redox couple of T(2)/T(-). The T(2)/T(-) DSCs using TiC and VC-MC CEs showed PCEs of 4.96 and 5.15%, much higher than that of the DSC using a Pt CE (3.66%). This work expands the list of potential CE catalysts, which can help reduce the cost of DSCs and thereby encourage their fundamental research and commercial application.     

Dye-sensitised solar cells with iodine-free discotic electrolytes

Discotic mesogenic molecules viz., hexahexylthiotriphenylene (HHTT) and hexahexyloxytriphenylene were applied, for the first time, as iodine-free redox electrolyte in dye-sensitised solar cells (DSSCs). The cell shows open circuit voltage (V_oc) of 0.95 V, short circuit current density (J_sc) of 0.534 mA/cm², fill factor 88.24% and overall power conversion efficiency (η) 0.45% in a typical fluorine doped tin oxide/TiO₂/N719/HHTT/Pt DSSC configuration. Scanning electron microscopy was used to study surface profile of electrolytes while electrochemical impedance spectroscopy was used to understand the electrochemical behaviour of electrolytes. The photovoltaic parameters were measured under standard conditions using Oriel solar simulator class AAA. These first results demonstrate the potential of the discotic molecules as charge transporter and mediator and show promise to be used in iodine-free DSSCs.     

向列相液晶4-氰基-4'-庚基联苯和4-氰基-4'-戊基联苯在准固态染料敏化太阳电池中的应用

将两种向列相液晶,4-氰基-4'-庚基联苯和4-氰基-4'-戊基联苯,引入到染料敏化太阳电池(DSC)用偏氟乙烯-六氟乙烯共聚物基准固态电解质中,以期提高DSC的光电转化效率.研究了液晶的引入对电解质中I-/I3-的氧化还原行为、DSC中TiO2/电解质界面的暗反应以及DSC光伏性能的影响.结果表明,尽管液晶的引入会降低电解质中I-/I3-的传输并且使得DSC中暗反应加快,但是DSC的短路电流密度却显著地提高,使DSC的光电转化效率增加.这可能是由于液晶的引入改善了DSC中的界面接触以及增加染料的光吸收引起的.     

Significant efficiency improvement of the black dye-sensitized solar cell through protonation of TiO2 films

This paper describes the influence of acid pretreatment ofTiO2 mesoporous films prior to dye sensitization on the performance of dye-sensitized solar cells based on [(C4H9)4N]3[Ru(Htcterpy)(NCS)3] (tcterpy = 4,4',4"-tricarboxy- 2,2',2"-terpyridine), the so-called black dye. The HCl pretreatment caused an increase in overall efficiency by 8%, with a major contribution from photocurrent improvement. It is speculated, from the analysis of incident photon-to-electron conversion efficiency, UV-vis absorption spectra, redox properties of the dye and TiO2, and the impedance spectra of the dye-sensitized solar cells, that photocurrent enhancement is attributed to the increases in electron injection and/or charge collection efficiency besides the improvement of light harvesting efficiency upon HCl pretreatment. Open-circuit photovoltage (V(oc)) remained almost unchanged in the case of significant positive shift of flat band potential for TiO2 upon HCl pretreatment. The suppression of electron transfer from conduction band electrons to the I3- ions in the electrolyte upon HCl pretreatment, reflected by the increased resistance at the TiO2/dye/electrolyte interface and reduced dark current, resulted in a V(oc) gain, which compensated the V(oc) loss due to the positive shift of the flat band. Using the HCl pretreatment approach, 10.5% of overall efficiency with the black dye was obtained under illumination of simulated AM 1.5 solar light (100 mW cm(-2)) using an antireflection film on the cell surface.     

Bis(4-methylthio)phenyl)amine-based hole transport materials for highly-efficient perovskite solar cells: insight into the carrier ultrafast dynamics and interfacial transport

Hole transport layers(HTLs) play a significant role in the performance of perovskite solar cells. A new class of linear smallmolecules based on bis(4-methylthio)phenyl)amine as an end group, carbon, oxygen and sulfur as the center atoms for the center unit(denoted as MT-based small-molecule), respectively, have been applied as HTL, and two of them presented the efficiency over 20% in the planar inverted perovskite solar cells(PSCs), which demonstrated a significant improvement in comparison with the widely used HTL, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(known as PEDOT:PSS), in the planar inverted architecture. The ultrafast carrier dynamics show that the excited hot carrier cooling process of MT-based small-molecule HTL samples is faster than that of PEDOT:PSS samples. The kinetic analysis of photo-bleaching peaks of femtosecond transient absorption spectra reveals that the traps at the interface between MT-based small-molecule HTLs and MAPbI_3 can be filled much quicker than that at PEDOT/MAPbI_3 interfaces. Moreover, the hole injection time from MAPbI_3 to MT-based small-molecule HTLs is around 10 times quicker than that to PEDOT:PSS. Such quick trap filling and hole extraction bring a significant enhancement in photovoltaic performances. These findings uncover the carrier transport mechanisms and illuminate a promising approach for the design of new HTLs for highly-efficient perovskite solar cells.     

用CdSe/ZnS量子点提高体异质结有机太阳电池的效率

通过掺杂吸收光谱在可见光波段的量子点可提高聚合物对可见光的吸收,因此掺杂CdSe/ZnS核-壳结构量子点(CQDs)能提高聚(3-己基噻吩):[6,6]-苯基-C61-丁酸甲酯(P3HT:PCBM)体异质结太阳电池的能量转换效率.本文研究了CdSe/ZnS量子点在P3HT:PCBM中的不同掺杂比例及其表面配体对太阳电池光伏性能的影响,优化器件ITO(氧化铟锡)/PEDOT:PSS(聚(3,4-乙撑二氧噻吩:聚苯乙烯磺酸)/P3HT:PCBM:(CdSe/ZnS)/Al的能量转换效率达到了3.99%,与相同条件下没有掺杂量子点的参考器件ITO/PEDOT:PSS/P3HT:PCBM/Al相比,其能量转换效率提高了45.1%.     

Molecular engineering of organic sensitizers for dye-sensitized solar cell applications

Novel unsymmetrical organic sensitizers comprising donor, electron-conducting, and anchoring groups were engineered at a molecular level and synthesized for sensitization of mesoscopic titanium dioxide injection solar cells. The unsymmetrical organic sensitizers 3-(5-(4-(diphenylamino)styryl)thiophen-2-yl)-2-cyanoacrylic acid (D5), 3-(5-bis(4-(diphenylamino)styryl)thiophen-2-yl)-2-cyanoacrylic acid (D7), 5-(4-(bis(4-methoxyphenylamino)styryl)thiophen-2-yl)-2-cyanoacrylic acid (D9), and 3-(5-bis(4,4'-dimethoxydiphenylamino)styryl)thiophen-2-yl)-2-cyanoacrylic acid (D11) anchored onto TiO2 and were tested in dye-sensitized solar cell with a volatile electrolyte. The monochromatic incident photon-to-current conversion efficiency of these sensitizers is above 80%, and D11-sensitized solar cells yield a short-circuit photocurrent density of 13.90 +/- 0.2 mA/cm(2), an open-circuit voltage of 740 +/- 10 mV, and a fill factor of 0.70 +/- 0.02, corresponding to an overall conversion efficiency of 7.20% under standard AM 1.5 sun light. Detailed investigations of these sensitizers reveal that the long electron lifetime is responsible for differences in observed open-circuit potential of the cell. As an alternative to liquid electrolyte cells, a solid-state organic hole transporter is used in combination with the D9 sensitizer, which exhibited an efficiency of 3.25%. Density functional theory/time-dependent density functional theory calculations have been employed to gain insight into the electronic structure and excited states of the investigated species.     

Oxoammonium enabled secondary doping of hole transporting material PEDOT:PSS for high-performance organic solar cells

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate(PEDOT:PSS) is one of the most widely used hole transporting materials in organic solar cells(OSCs). Multiple strategies have been adopted to improve the conductivity of PEDOT:PSS, however,effective strategy that can optimize the conductivity, work function, and surface energy simultaneously to reach a better energy alignment and interface contact is rare. Here, we demonstrate that oxoammonium salts(TEMPO~+X~-) with different counterions can act as facile and novel dopants to realize secondary doping of PEDOT:PSS. The effective charge transfer process achieved between TEMPO~+X~- and PEDOT:PSS results in enhanced carrier density and improved conductivity of PEDOT:PSS. Moreover,different counterions of TEMPO~+X~- can tune the work function and surface energy of PEDOT:PSS, enabling improved device performances. The resulting device with PM6:Y6 as the active layer shows a high power conversion efficiency(PCE) over 16%.Moreover, this doping strategy can also be applied to other conjugated polymers such as poly(3-hexylthiophene). This work provides a promising strategy to tune the properties of conjugated polymers through doping, thus effectively boosting the performance of organic solar cells.     

Improved Interfacial Contact for Pyramidal Texturing of Silicon Heterojunction Solar Cells

Reducing the surface reflectivity of silicon substrates is essential for preparing high-performance Si-based solar cells. We synthesized pyramid-nanowire-structured Si (Si-PNWs) anti-reflection substrates, which have excellent light-trapping ability (<4% reflectance). Furthermore, diethyl phthalate (DEP), a water-insoluble phthalic acid ester, was applied to optimize the Si-PNWs/PEDOT:PSS interface; the photoelectric conversion efficiency of heterojunction solar cells was shown to increase from 9.82% to 13.48%. We performed a detailed examination of the shape and optical characteristics of Si-PNWs, as well as associated photoelectric performance tests, to investigate the origin of performance improvements in Si-PNWs/PEDOT:PSS heterojunction solar cells (HSCs).     

添加剂对染料敏化太阳电池电解质性能的影响

以N-甲基咪唑、苯并咪唑、叔丁基吡啶和离子液体1-甲基-3-乙基咪唑三氟乙酸盐(EMITA)作为染料敏化太阳电池(DSCs)电解质溶液中的添加剂, 使用超微电极通过循环伏安法研究其对液体电解质中I-3和I-氧化还原行为的影响, 通过电化学阻抗谱研究了上述四种添加剂对Pt电极电解质界面的影响. 结果表明, 添加剂EMITA的加入使I-3在电解质中的扩散系数减小, Pt电极电解质界面上的界面传输电阻Rct增大, 电解质的电阻降低; 光伏性能测试表明, EMITA的添加提高了DSCs的开路电压和填充因子, 其DSCs的光电转换效率达到了5.72%.     

TTA as a potential hole transport layer for application in conventional polymer solar cells

Hole transport layers(HTLs) play a vital role in organic solar cells(OSCs). In this work, a derivative of tetrathiafulvalene with four carboxyl groups TTA was introduced as a novel HTL to fabricate OSC with high performance. Displaying a better energy level match between HTL and active layers, the TTA based devices show a peak power conversion efficiency of 9.09%, which is comparable to the devices based on PEDOT:PSS. The favorable surface morphology recorded via atomic force microscopy, low series loss and charge recombination indicated by electrochemical impedance spectroscopy, synchronously verify the potential of TTA for application in OSCs as a valid kind of HTLs.     

Interfacial Engineering of CdO–CdSe 3D Microarchitectures with in situ Photopolymerized PEDOT for an Enhanced Photovoltaic Performance

In the present work, porous 3D CdO‐microstructured electrode obtained by pyrolysis of 3D CdCO₃ microstructures is self‐sensitized with CdSe using an ion exchange reaction. After sensitization, an interfacial treatment of the CdO–CdSe interface is performed by depositing a thin film of PEDOT using a photoinduce polymerization route. The microstructured electrode before and after interfacial treatment is characterized using field‐emission scanning microscope, energy dispersive X‐ray analyzer, contact angle measurement, UV–Visible absorption spectrophotometer and X‐ray photoelectron spectrometer. After constructing a liquid junction solar cell with a Pt counter electrode, the photovoltaic performance and interfacial charge transfer kinetics across the CdO–CdSe interface before and after PEDOT treatment are investigated. The results exhibit an improved interfacial charge‐transfer resistance after the PEDOT treatment, which leads to enhance the short‐circuit current by 15.81% and the power conversion efficiency by 19.82%.