Sand consolidation with calcium phosphate-polyelectrolyte composites

A new method for the consolidation of loose sand formations has been developed. The method involves in situ precipitation of a composite calcium phosphate-polyelectrolyte salt that binds together with loose sand grains, thus resulting to their consolidation. Three different polyelectrolytes (PE) were tested, i.e., polyacrylic acid (PAA), polyallylamine hydrochloride (PAH), and polyethylenimine (PEI). The effect of PE tested on the thermodynamics and the kinetics of precipitation of calcium phosphate salts was investigated. Three types of experiments were done. Investigation of the adsorption of PE on either hydroxyapatite (Ca(5)(PO(4))(3)OH, HAP) crystals or on sand grains. Measurement of the kinetics of heterogeneous nucleation of HAP on the solid substrates and the mechanical properties of the obtained crystals in batch experiments of low and high supersaturation solutions, respectively. Evaluation of the consolidation in sand packs in order to investigate the effectiveness of the method. The crystallization rates, R(p), on HAP crystals in the presence of the PE tested were found in the order R(p)(PAA)>R(p)(PEI)>R(p)(PAH), while nucleation and crystal growth on silicate sand took place only in the absence of adsorbed PE. PAH favored strongly the consolidation process, whereas PEI and PAA resulted in the formation of poorly consolidated grain agglomerates.     

Sorption of tartrate ions to lanthanum (III)-modified calcium fluor- and hydroxyapatite

The present article details the formation of lanthanum-modified apatites and the binding process of tartrate ions with these obtained apatites. Chemical analyses, FT-IR and (31)P NMR spectroscopies, XRD powder, TGA, and TEM analyses were employed for studying the reaction between Ca(10)(PO(4))(6)(OH)(2) (HAp) or Ca(10)(PO(4))(6)(F)(2) (FAp) and LaCl(3). The reaction was found to take place mainly through partial dissolution of the apatite followed by precipitation of a new phase containing lanthanum phosphate. When La(3+) was introduced in the presence of L(+)-tartaric acid (TAH(2)), no fundamental changes were observed in the HAp or FAp structures. However, there did occur a formation of a new phase of Ca or/and La tartrate salt.     

医用CVIC/C复合材料表面仿生沉积生物活性钙磷涂层

为了在医用化学气相渗透工艺(CVI)C/C复合材料表面制备生物活性钙磷涂层,用阴极声电化学工艺处理CVIC/C复合材料,再将试样浸泡于过饱和钙磷溶液中,使其诱导钙磷晶体生长.XPS研究表明,经声电工艺处理后,CVIC/C复合材料表面发生了改性;SEM,XRD和FTIR研究表明,在过饱和钙磷溶液中,未经声电化学处理的CVIC/C复合材料不具有诱导钙磷晶体生长的功能,而改性的CVIC/C表面能够诱导钙磷晶体生长,形成片状五水磷酸八钙(OCP)涂层.同时讨论了OCP沉积的形成机理.     

A metallic cobalt electrode for the indirect potentiometric determination of calcium and magnesium in natural waters using flow injection analysis

A flow injection analysis of Ca(2+) and Mg(2+) using indirect potentiometric detection in natural waters is proposed, where Ca(2+) or Mg(2+) are injected into a buffer carrier containing phosphate, resulting in the formation of Ca(3)(PO(4))(2) or Mg(3)(PO(4))(2). The consequent reduction in free phosphate in the carrier solution is detected using a metallic cobalt wire electrode. Indirect electrode response was used and the experimental conditions affecting electrode response were optimized. Responses were linear in the concentration range 5x10(-4) to 5x10(-3) M with a detection limit of 1x10(-5) M in 20 mM phosphate buffer at pH 8.0. The relative standard derivation at 1 mM of Ca(2+) and Mg(2+) were 3.9 and 3.7% (n=10), respectively. EGTA and 8-hydroxyquinoline were used as the masking agents for Ca(2+) and Mg(2+), respectively. Concentrations of Ca(2+) and Mg(2+) in natural waters were successfully determined by the proposed method.     

Synthesis and characterization of new calcium phenylphosphonates and 4-carboxyphenylphosphonates

Three new calcium phenylphosphonates, CaC(6)H(5)PO(3).2H(2)O, Ca(3)(C(6)H(5)PO(3)H)(2)(C(6)H(5)PO(3))(2).4H(2)O, and CaC(6)H(5)PO(3).H(2)O, and two calcium 4-carboxyphenylphosphonates, Ca(HOOCC(6)H(4)PO(3)H)(2) and Ca(3)(OOCC(6)H(4)PO(3))(2).6H(2)O, were prepared. It was found that CaC(6)H(5)PO(3).2H(2)O transformed into previously known Ca(C(6)H(5)PO(3)H)(2) via Ca(3)(C(6)H(5)PO(3)H)(2)(C(6)H(5)PO(3))(2).4H(2)O in the presence of phenylphosphonic acid, and vice versa, Ca(C(6)H(5)PO(3)H)(2) turned into CaC(6)H(5)PO(3).2H(2)O in a weak basic medium. A similar relationship was found between Ca(HOOCC(6)H(4)PO(3)H)(2) and Ca(3)(OOCC(6)H(4)PO(3))(2).6H(2)O; i.e., Ca(3)(OOCC(6)H(4)PO(3))(2).6H(2)O transformed into Ca(HOOCC(6)H(4)PO(3)H)(2) in the presence of 4-carboxyphenylphosphonic acid. On the contrary, Ca(3)(OOCC(6)H(4)PO(3))(2).6H(2)O is formed from Ca(HOOCC(6)H(4)PO(3)H)(2) in the presence of ammonium as a weak base. The structure of Ca(HOOCC(6)H(4)PO(3)H)(2) was solved from X-ray powder diffraction data by an ab initio method using a FOX program. The compound is monoclinic, space group C2/c (No. 15), a = 49.218(3) A, b = 7.7609(4) A, c = 5.4452(3) A, beta = 128.119(3) degrees , and Z = 4. Its structure is one-dimensional with [Ca(2)(HOOCC(6)H(4)PO(3)H)(4)](infinity) ribbons forming basic building blocks. The ribbons are held together by hydrogen bonds between carboxylic groups.     

胆盐与磷酸钙的相互作用

胆汁的pH条件下(pH=6～8)，应该生成无定形磷酸钙(ACP)，而在胆结石中磷酸钙通常以羟基磷灰石的形式出现.利用谱学方法研究了ACP与胆盐的作用.结果表明，胆盐以胶团的形式与ACP作用，在溶液中形成复合胶团，使其溶解度增加.不同类型胆盐与ACP的作用能力不同：脱氧胆酸钠(NaDC) > 牛磺胆酸钠(NaTC) > 胆酸钠(NaC).胆盐与ACP中结合钙的亲和能力大于结合钙的亲和能力，使ACP在胆汁的环境下容易转化为羟基磷灰石.     

电沉积磷酸钙生物活性陶瓷

在医用合金Ti6A14V基底上研究了电流密度、阴极电位和电解液温度等实验条件对磷酸钙生物陶瓷电沉积层的组成、结构和表面形貌等特性的影响，用扫描电子显微镜（SEM）、X射线衍射（XRD）、傅立叶变换红外光谱（FTIR）和感耦等离子体原子发射光谱（ICP／AES）等技术对磷酸钙陶瓷沉积层进行了表征．依据各种用酸钙盐的热力学性质，采用低温城液后处理的方法将前驱体转化为均匀单一的多孔状纯羟基历灰石沉积层．     

Syntheses, structures, and ion-exchange properties of the three-dimensional framework uranyl gallium phosphates, Cs4[(UO2)2(GaOH)2(PO4)4].H2O and Cs[UO2Ga(PO4)2

The reaction of UO(2)(NO(3))(2).6H(2)O with Cs(2)CO(3) or CsCl, H(3)PO(4), and Ga(2)O(3) under mild hydrothermal conditions results in the formation of Cs(4)[(UO(2))(2)(GaOH)(2)(PO(4))(4)].H(2)O (UGaP-1) or Cs[UO(2)Ga(PO(4))(2)] (UGaP-2). The structure of UGaP-1 was solved from a twinned crystal revealing a three-dimensional framework structure consisting of one-dimensional (1)(infinity)[Ga(OH)(PO(4))(2)](4-) chains composed of corner-sharing GaO(6) octahedra and bridging PO(4) tetrahedra that extend along the c axis. The phosphate anions bind the UO(2)(2+) cations to form UO(7) pentagonal bipyramids. The UO(7) moieties edge-share to create dimers that link the gallium phosphate substructure into a three-dimensional (3)(infinity)[(UO(2))(2)(GaOH)(2)(PO(4))(4)](4-) anionic lattice that has intersecting channels running down the b and c axes. Cs(+) cations and water molecules occupy these channels. The structure of UGaP-2 is also three-dimensional and contains one-dimensional (1)(infinity)[Ga(PO(4))(2)](3-) gallium phosphate chains that extend down the a axis. These chains are formed from fused eight-membered rings of corner-sharing GaO(4) and PO(4) tetrahedra. The chains are in turn linked together into a three-dimensional (3)(infinity)[UO(2)Ga(PO(4))(2)](1-) framework by edge-sharing UO(7) dimers as occurs in UGaP-1. There are channels that run down the a and b axes through the framework. These channels contain the Cs(+) cations. Ion-exchange studies indicate that the Cs(+) cations in UGaP-1 and UGaP-2 can be exchanged for Ca(2+) and Ba(2+). Crystallographic data: UGaP-1, monoclinic, space group P2(1)/c, a = 18.872(1), b = 9.5105(7), c = 14.007(1) A, beta = 109.65(3)(o) , Z = 4 (T = 295 K); UGaP-2, triclinic, space group P, a = 7.7765(6), b = 8.5043(7), c = 8.9115(7) A, alpha = 66.642(1)(o), beta = 70.563(1)(o), gamma = 84.003(2)(o), Z = 2 (T = 193 K).     

Luminescence investigation on ultraviolet-emitting rare-earth-doped phosphors using synchrotron radiation

Three series of new ultraviolet-emitting Ca(9)Y(PO(4))(7):Ln(3+) (Ln = Ce, Gd, Pr) phosphors were synthesized, and their luminescence was investigated. Under vacuum ultraviolet excitation Ca(9)Y(PO(4))(7):Ce(3+) phosphors emit UVA light with one broad emission centered at 346 nm, on account of the 5d(1) → 4f(1) transition of Ce(3+) ions; the optimal doping concentration of these phosphors is 0.2 mol. Ca(9)Y(PO(4))(7):Gd(3+) phosphors show a strong 4f(7) → 4f(7) transition and a sharp UVB emission band at 312 nm; the optimal doping concentration of these phosphors is 0.7 mol. The PL spectra of Ca(9)Y(PO(4))(7):Pr(3+) show two broad UVC emission bands centered between 230 and 340 nm, owing to the 4f(1)5d(1) → 4f(2) transition of Pr(3+) ions; the optimal doping concentration of these phosphors is 0.2 mol. Under 172 nm excitation, we found that the luminescence intensity of the UVA-emitting Ca(9)Y(PO(4))(7):0.2Ce(3+) is 0.3675 times that of BaSi(2)O(5):0.05Pb(2+), that of the UVB-emitting Ca(9)Y(PO(4))(7):0.7Gd(3+) is 1.7 times that of YAl(3)(BO(3))(4):0.25Gd(3+), and that of the UVC-emitting Ca(9)Y(PO(4))(7):0.2Pr(3+) is 1.5 times that of LaPO(4):0.1Pr(3+). The thermal stability investigation indicated that the luminescence decay was only 9.2%, 18.2%, and 10.3% for Ca(9)Y(PO(4))(7):0.2Ce(3+), Ca(9)Y(PO(4))(7):0.7Gd(3+), and Ca(9)Y(PO(4))(7):0.2Pr(3+) at 250 °C relative to that at ambient temperature, respectively. The Ca(9)Y(PO(4))(7):Ln(3+) (Ln = Ce, Gd, Pr) phosphors exhibit high emission efficiency and excellent thermal stability.     

(CH3)2NH(CH2)2NH(CH3)2][(UO2)2F2(HPO4)2]: a new organically templated layered uranium phosphate fluoride--synthesis, structure, characterization, and ion-exchange reactions

A new organically templated layered uranium phosphate fluoride, [(CH(3))(2)NH(CH(2))(2)NH(CH(3))(2)][(UO(2))(2)F(2)(HPO(4))(2)] has been synthesized by hydrothermal reaction of UO(3), H(3)PO(4), HF, and (CH(3))(2)NCH(2)CH(2)N(CH(3))(2) at 140 degrees C. [(CH(3))(2)NH(CH(2))(2)NH(CH(3))(2)][(UO(2))(2)F(2)(HPO(4))(2)] has a layered crystal structure consisting of seven-coordinated UO(5)F(2) pentagonal bipyramids and four-coordinated HPO(4) tetrahedra. Each anionic layer containing three-, four-, and six-membered rings is separated by [(CH(3))(2)NH(CH(2))(2)NH(CH(3))(2)](2+) cations. The [(CH(3))(2)NH(CH(2))(2)NH(CH(3))(2)](2+) cations may be readily exchanged with the M(2+) ions (M = Ba, Sr and Ca) in water to give high crystalline AE(UO(2))(2)(PO(4))(2).6H(2)O (AE = Ca, Sr, Ba).     

Surface modification of calcium hydroxyapatite with pyrophosphoric acid

The surface of synthetic colloidal calcium hydroxyapatite (Ca(10)(PO(4))(6)(OH)(2); CaHap) was treated with pyrophosphoric acid (H(4)P(2)O(7); PP) in acetone and the materials were characterized by XRD, thermal analysis, N(2) adsorption, TEM, and FTIR. No remarkable change in XRD patterns or in particle morphology by the modification was observed. The additional amount of PO(4) of CaHap was increased with an increase in PP concentration. The Ca/P molar ratio of CaHap was decreased from 1.62 to 1.35 by the modification. IR results indicated that the PP reacts with surface P-OH groups of CaHap to form additional surface P-OH groups as follows: surface P-OH+H(4)P(2)O(7)--> surface P-O-PO(OH)(2) + H(3)PO(4). When the modified CaHap with Ca/P molar ratio less than 1.50 was treated at 850 degrees C in air, the materials transformed into beta-Ca(3)(PO(4))(2).     

Surface properties of various powdered hydroxyapatites

Electrophoretic mobilities of various synthetic and semisynthetic hydroxyapatites (Ca10(PO4)6(OH)2, HAP) suspended in aqueous solutions have been measured as a function of pH and calcium concentration. The studied powders differ in particle size, crystallinity degree and surface contamination (carbonate). When equilibrated in mineral acids or bases, a large plateau of negative mobility is observed in the pH range 5-8, with increasing negative values at higher pH. Only in the case of the sample composed of nanoparticles, positive mobility obtains at pH < 8.9. When Ca2+ is added, positive mobility values are observed for all samples, and a bell-shaped profile results as a function of pH. Two possible models are explored to describe the results: the Nernstian approach, which assumes solubility equilibrium and surface potentials determined by the three potential-determining ions (Ca2+, PO3-4, and OH-), and the surface complexation approach, based on the idea of negligible phase transfer of structural phosphate. The Nernstian model is inadequate, whereas a very simple surface complexation model based on the equations Ca5(PO4)+3 = Ca4(PO4)-3 + Ca2+,Ca4(PO4)-3 + H+ = Ca4(PO4)2(PO4H),Ca5(PO4)+3 + OH- = Ca5(PO4)3(OH),coupled with a very simple electrical double layer, model suffices to reproduce the bell-shaped profile of the mobility as a function of pH in the presence of added calcium salts. The results also show that the sample composed of nanoparticles exchanges ions more easily with the solution, without reaching the solubility equilibrium in the explored timespans. In the presence of soluble phosphate salts, it is postulated that the same surface ensembles define the surface charge, with participation of phosphate as described by the equation Ca5(PO4)+3 + PO3-4 = Ca4(PO4)-3.HAP is just one member of a family of calcium phosphates with different (Ca)/(P) ratios. Electrophoretic mobilities of another member, tricalcium diphosphate, Ca3(PO4)2, were also measured and shown to be described by the same basic model. Comparison with previous literature data shows that the negative plateau in the mobility is a general feature of many HAP samples at low Ca2+, again in agreement with the surface complexation model. FTIR data demonstrates that surface phosphate indeed undergoes protonation, as postulated in the model.     

A comparative study of the metastable equilibrium solubility behavior of high-crystallinity and low-crystallinity carbonated apatites using pH and solution strontium as independent variables

Using solution strontium and pH as independent variables, the metastable equilibrium solubility (MES) behavior of two carbonated apatite (CAP) samples has been examined, a high-crystallinity CAP (properties expected to be similar to dental enamel) and a low-crystallinity CAP (properties expected to be similar to bone mineral). CAP samples were prepared by precipitation/digestion: (CAP A: high-crystallinity, 1.3 wt% CO3, synthesized at 85 degrees C; CAP B: low-crystallinity, 6.4 wt% CO3, synthesized at 50 degrees C). Baseline MES distributions were determined in a series of 0.1 M acetate buffers containing only calcium and phosphate (no strontium) over a broad range of solution conditions. To assess the influence of strontium, MES profiles were determined in a similar fashion with 20, 40, 60, and 80% of the solution calcium being replaced on an equal molar basis by solution strontium. To determine the correct function governing CAP dissolution, ion activity products (IAPs) were calculated from the compositions of buffer solutions based on the hydroxyapatite template (Ca(10-n)Sr(n)(PO4)6(OH)2 (n = 0-10)) and the calcium/hydroxide deficient hydroxyapatite template (Ca(9-n)Sr(n)(HPO4)(PO4)5OH (n = 0-9)). Findings: (a) for CAP A, at high solution strontium/calcium ratios, the MES profiles were essentially superimposable when the solution IAPs were calculated using the stoichiometry of Ca6Sr4(PO4)6(OH)2 and for CAP B by a stoichiometry of Ca7Sr2(HPO4)(PO4)5OH; (b) for CAP A, at low strontium/calcium ratios, the stoichiometry yielding MES data superpositioning was found to be that of hydroxyapatite and for CAP B, that of calcium/hydroxide deficient hydroxyapatite. When other stoichiometries were assumed, good superpositioning of the data was not possible.     

Sol-Gel Derived Calcium Phosphate Coatings for Biomedical Applications

Hydroxyapatite (HA) coatings have received considerable attention because they exhibit bone bonding capabilities. Unfortunately the common forms of coating production result in cracking and degradation of HA due to the thickness of the coatings and the elevated temperatures employed. This study demonstrates the production of sub-micron, crack-free calcium phosphate coatings on quartz glass substrates using a sol-gel dip-coating technique and firing temperatures below 1000°C.Coatings fired at 1000°C comprised a mixture of hydroxyapatite (HA) and tricalcium phosphate (TCP). XPS analysis of the coating surface showed that the Ca/P ratio lay in the range 1.5–1.67, and that there was a contribution from carbon in the form of carbonate.It is proposed that the sol-gel coatings comprising a resorbable (TCP) and an insoluble (HA) phase have potential benefits in certain implant applications.     

脉冲电化学驱动壳聚糖原位调控制备羟基磷灰石/银复合涂层

采用脉冲电化学驱动壳聚糖原位调控制备了具有抗菌性的羟基磷灰石/银纳米复合涂层.考察了电解液中银离子浓度、钙磷盐浓度等对复合涂层的形貌及成分的影响.探讨了壳聚糖调控羟基磷灰石和银纳米粒子的形成机理,发现在本研究的较佳实验条件为电位-1.3 V,Ag~+浓度为0.06 g·L~(-1),Ca~(2+)浓度为5 mmol·L~(-1).在此基础上对复合涂层的生物活性、生理稳定性能、抗菌性能进行分析.结果表明:复合涂层呈纳米球状,由羟基磷灰石、银、壳聚糖三相组成,并且表面有一层壳聚糖覆盖.银纳米粒子和羟基磷灰石纳米粒子在复合涂层中均匀分布.将复合涂层浸泡在SCPS溶液中37°C浸泡矿化10天后,在复合涂层表面生产细针状排列整齐的羟基磷灰石,且在(002)晶面25.8°处发生显著择优生长,表明复合涂层在快速矿化液中能诱导磷灰石生成,生物活性好.将复合涂层浸泡在37°C PBS溶液中考察其生理稳定性,壳聚糖对复合涂层中Ca~(2+)和Ag~+实现双重离子释放,且降低了离子释放速度,涂层具有良好的生理稳定性.抗菌实验表明复合涂层对大肠杆菌和金黄色葡萄球菌抗菌率达到99%以上,抗菌能力强.     

Controlled synthesis of hydroxyapatite-supported palladium complexes as highly efficient heterogeneous catalysts

Achieving precise control of active species on solid surfaces is one of the most important goals in the development of highly functionalized heterogeneous catalysts. The treatment of hydroxyapatites with PdCl(2)(PhCN)(2) gives two new types of hydroxyapatite-bound Pd complexes. Using the stoichiometric hydroxyapatite, Ca(10)(PO(4))(6)(OH)(2), we found that monomeric PdCl(2) species can be grafted on its surface, which are easily transformed into Pd(0) particles with narrow size distribution in the presence of alcohols. Such metallic Pd species can effectively promote alcohol oxidation using molecular oxygen and are shown to give a remarkably high TON of up to 236 000. Another monomeric Pd(II) phosphate complex can be generated at a Ca-deficient site of the nonstoichiometric hydroxyapatite, Ca(9)(HPO(4))(PO(4))(5)(OH), affording a catalyst with Pd(II) structure and high activity for the Heck and Suzuki reactions. To the best of our knowledge, the PdHAP are one of the most active heterogeneous catalysts for both alcohol oxidation under an atmospheric O(2)() pressure and the Heck reaction reported to date. These Pd catalysts are recyclable in the above organic reactions. Our approach to catalyst preparation based on the control of Ca/P ratios of hydroxyapatites represents a particularly attractive method for the nanoscale design of catalysts.     

A red-emitting Ca8MgLa(PO4)7:Ce3+,Mn2+ phosphor for UV-based white LEDs application

Ca(8)MgLa(PO(4))(7):Ce(3+),Mn(2+) phosphors have been prepared by a conventional solid state reaction under a weak reductive atmosphere. The crystal structure and photoluminescent properties were investigated. It was found that the red emission at 640nm originated from the (4)T(1)((4)G)→(6)A(1)((6)S) transition of Mn(2+) increases dramatically by a factor of 6.4 with the optimum Ce(3+) co-doping. The energy transfer from Ce(3+) to Mn(2+) was proposed to be resonance-type via an electric dipole-dipole mechanism and the energy transfer efficiency was also calculated by the relative emission intensity. With the broadband ultraviolet (UV) absorption of Ce(3+) and the suitable color coordinates, Ca(8)MgLa(PO(4))(7):Ce(3+),Mn(2+) phosphors might be a promising candidate as red phosphors in the field of UV-based white light-emitting diodes.     

Temperature driven morphological changes of chemically precipitated hydroxyapatite nanoparticles

Hydroxyapatite (HA) is synthesized by a wet chemical route using calcium hydroxide and ortho-phosphoric acid at various temperatures (40, 80, and 100 degrees C). X-ray diffraction of the precipitate particles revealed HA as the predominant phase (>99%) with a small amount of beta-tricalcium phosphate. Fourier transform infrared spectroscopy indicated the presence of carbonate substitution, which decreased with increasing temperature. Transmission electron microscopy observations revealed needle-shaped particles with a high aspect ratio at 40 degrees C, which changed to spheroidal when the precipitation temperature was increased to 100 degrees C. The changes in the morphology with temperature were analyzed taking into account the driving force for the HA precipitation and the supersaturation level of Ca2+ and PO4(3-) ions with respect to HA. The analysis indicated that the supersaturation level of the reactants, especially the concentration of Ca2+ ions, played a predominant role on the precipitate morphology for this classical acid-base reaction.     

新表面化学处理用于Ti6Al4V合金表面仿生磷酸钙涂层的制备

报道了一种新的非腐蚀性表面化学处理用于Ti6Al4V合金表面仿生磷酸钙涂层的制备. 将Ti6Al4V合金从浸入的过饱和磷酸钙溶液中拉出, 在空气中挥干表面附着的过饱和润湿膜, 在Ti6Al4V表面生成磷酸钙晶体, 且其表面覆盖率随处理次数增加而增加, 直至表面完全被覆盖. 再将磷酸钙晶体覆盖的Ti6Al4V浸入过饱和溶液后, 表面的磷酸钙晶体迅速生长成为均匀的磷酸钙涂层. 该表面化学处理的机理可能为一个挥发表面结晶过程, 其优点在于润湿膜干燥为表面成核提供驱动力, 因此无需采用表面腐蚀性处理或不稳定的高过饱和溶液处理.     

Electrophoretic deposition of calcium phosphates from non-aqueous media

Electrophoretic deposition of ultrafine calcium phosphates from non-aqueous suspensions onto metallic substrates was attempted in order to obtain coatings with varying porosities. Aging effects were studied by measuring changes in the electrophoretic deposition behavior of the calcium phosphate particles in the non-aqueous suspensions. It was observed that the surfaces of the calcium phosphates develop significant electrostatic charge during aging in order to enable the formation of a dense and uniform deposit. The addition of surface charge conditioners such as HCl was found to have a similar effect. Dispersion conditions were varied to obtain coatings of the desired green densities, which were sintered to different microporosities.