Degradation of poly(vinyl chloride) and nitrocellulose in XPS

Measurements have been made of the degradation rates for poly(vinyl chloride) (PVC) and nitrocellulose with cellulose acetate (NC) in x‐ray photoelectron spectroscopy. These materials form part of earlier studies published by others to evaluate instrumental degradation factors. In the earlier studies, results showed significant scatter such that the relative rates varied significantly from instrument to instrument. It is shown here that this variation could arise from different levels of adventitious electrons in the different instruments as well as different layer thicknesses exhibiting the degradation in PVC and NC. The former depends on electrodes in the system and the neutralizing parameters, whereas the latter causes the relative degradation rates to depend on the angle of emission of the detected electrons. These will have varied from laboratory to laboratory in the earlier study. The present study leads to simple recommendations for operating conditions to reduce the degradation effects observed. Copyright © 2003 John Wiley & Sons, Ltd.     

Heat capacity and thermodynamic properties of 1-hexadecanol

Three different nitrocellulose (NC) samples produced from linters were investigated. DSC studies on the NC+sym-diethyldiphenylurea (C1) mixtures were carried out. The influence of storage time on their pore structures was examined using thermoporometry. The results led to conclusion that large pores are multiples of small ones. The parameter n was used to characterize the number of C1 molecules equivalent to NC ring. Its value for short storage time was about 9 but for longer time reached the value of 3. The influence of thermal history on the phase transition and porosity of the different nitrocellulose samples was different.     

Effects of molecular weight of nitrocellulose on structure and properties of polyurethane/nitrocellulose IPNs

Semi‐interpenetrating polymer network (semi‐IPN) coatings were prepared by using castor oil‐based polyurethane (PU) and nitrocellulose (NC) with various viscosity‐average molecular weights (M_η) from 6 × 10⁴ to 42 × 10⁴, and coated on a regenerated cellulose (RC) film to obtain water‐resistant film. The PU/NC coatings and coated films, which were cured at 80°C for 5 min and 2 min, respectively, were investigated by infrared (IR) and ultraviolet (UV) spectroscopy, X‐ray diffraction, swelling test, strength test, dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The results show that the crosslink densities of the PU/NC semi‐IPNs were smaller than that of pure PU, and decreased with the decrease of M_η of nitrocellulose (NC M_η), indicating NC molecules cohered intimately with PU, and hindered the PU network formation. The physical and mechanical properties of the films coated with PU/NC coatings were significantly improved. With the increase of NC M_η, the strength and thermal stability of the coated films increased, but the pliability, water resistivity, and optical transmission decreased slowly. The PU/NC coating with low NC M_η more readily penetrated into the RC film, and reacted with cellulose, resulting in a strong interfacial bonding and dense surface caused by intimate blend of PU/NC in the coated films. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1623–1631, 1999     

Cut growth and abrasion behaviour,and morphology of natural rubber filled with MWCNT and MWCNT/carbon black

Various amounts of predispersed multi-wall carbon nanotubes (MWCNT) were mixed with natural rubber (NR), with and without carbon black (CB), for preparing MWCNT-filled NR (NC) and MWCNT/CB-filled NR (NH) vulcanizates. All NH vulcanizates contained 30 phr CB and the amount of MWCNT for both NC and NH was varied from 0 to 8 phr. Helium ion microscopy (HIM) and FE-SEM images showed that MWCNT in the NH was dispersed much better than in the NC. Additionally, the well dispersed CB and MWCNT in the NH functioned synergistically in promoting an increase in longitudinal crack growth, leading to enhancement of edge-cut tensile strength (CTS) with increasing MWCNT loading. In contrast, all NC specimens ruptured in a simple lateral direction relating to their lower CTS. Results also revealed that abrasion resistance of the NH was not significantly changed with increasing MWCNT, whereas that of the NC increased. Nevertheless, abrasion resistance of both vulcanizates showed good correlation with the average value of ridge spacing on their abraded surfaces. It was also found that tensile strength of the NH was almost unchanged when the MWCNT loading was increased because the reinforcement by CB predominates over the MWCNT. However, 100% modulus and hardness of both NC and NH increased with increasing MWCNT content.     

超级铝热剂的制备、表征及其燃烧催化作用

用纳米铝粉和纳米氧化铅、纳米氧化铜和纳米三氧化二铋为原料,采用超声分散复合的方法,制备了纳米超级铝热剂Al/PbO、Al/CuO和Al/Bi₂O₃。采用X射线粉末衍射(XRD)、扫描电镜及能谱分析(SEM-EDS)和红外光谱(IR)对原料和产物的物相、组成、形貌和结构进行分析表征;运用差示扫描量热仪(DSC)评估三种超级铝热剂与双基推进剂主要组分的相容性;研究了3种超级铝热剂对双基推进剂燃烧性能的影响。结果表明,Al/PbO、Al/CuO和Al/Bi₂O₃与推进剂主要组分硝化棉(NC)、硝化棉/硝化甘油(NC/NG)混合物和吉纳(DINA)的相容性均良好,而与黑索今(RDX)和1,3-二甲基-1,3-二苯基脲(C₂)相对较为敏感;含三种纳米超级铝热剂的双基推进剂表现出优异的燃烧性能。     

Influence of tailored CuO and Al/CuO nanothermites on the thermocatalytic degradation of nitrocellulose and combustion performance of AP/HTPB composite propellant

Cellulose - Al/CuO nanothermites have displayed unique catalytic activities in accelerating the thermolysis of nitrocellulose (NC) and combustion characteristics of AP/HTPB propellant depending on...     

Studies on kinetics and mechanism of initial thermal decomposition of nitrocellulose

The thermal decomposition of nitrocellulose (NC) 12.1% N, has been studied with regard to kinetics, mechanism, morphology and the gaseous products thereof, using thermogravimetry (TG), differential thermal analysis (DTA), IR spectroscopy, differential scanning calorimetry (DSC) and hot stage microscopy. The kinetics of the initial stage of thermolysis ofNC in condensed state has been investigated by isothermal high temperature infrared spectroscopy (IR). The decomposition ofNC in KBr matrix in the temperature range of 142–151°C shows rapid decrease in O?NO₂ band intensity, suggesting that the decomposition of NC occurs by the rupture of O?NO₂ bond. The energy of activation for this process has been determined with the help of Avrami-Erofe'ev equation (n=1) and is ≈188.35 kJ·mol^?1. Further, the IR spectra of the decomposition products in the initial stage of thermal decomposition ofNC, indicates the presence of mainly NO₂ gas and aldehyde.     

Performance evaluation of the different nano-enhanced polysulfone membranes via membrane distillation for produced water desalination in Sert Basin-Libya

A Polysulfone-Polyethylene glycol (PS/PEG) flat sheet membrane was prepared by phase inversion technique. Dimethyl Formamide (DMF) was utilized as a solvent and deionized water was utilized as the coagulant. Polyethylene glycol (PEG) of a various dose of PEG 2000 was utilized as the polymeric improvers and as a pore-forming agent in the casting mixture. The single-walled carbon nanotube (SWCNTs), multi-walled carbon nanotube (MWCNTs), aluminum oxide (Al₂O₃) and copper oxide (CuO) nanoparticles (NPs) were utilized to improve the PS/PEG membrane performances. The characterizations of the neat PS, PS/PEG, PS/PEG/Al2O3 (M1) PS-PEG/CuO (M2), PS-PEG/SWCNTs (M3) and PS/PEG/MWCNTs (M14) nanocomposite (NC) modified membranes were acquired via Fourier-transform infrared analysis (FTIR), water contact angle estimation (WCA), scanning electron microscope (SEM), dynamic mechanical analyzer (DMA) and thermogravimetric analysis (TGA). Enhanced Direct contact membrane distillation (EDCMD) unit was used for estimating the efficiency of the performance of the synthesized NC membranes via 60 °C feed synthetic water and/or saline oil field produced water samples containing salinities 123,14 mg/L. Adjusting the operational procedures and water characteristics confirmed a high salt rejection of 99.99% by the synthesized NC membranes. The maximum permeate flux achieved in the order of SWCNTs (20.91) > Al₂O₃ (19.92) > CuO (18.92) > MWCNT (18.20) (L/m².h) with adjusted concentration of 0.5, 0.75, 0.75, 0.1 wt% compared with PS weight, i.e. 16%. The optimum operational circumstances comprised feed and permeate temperatures 60 °C and 20 °C, respectively. The achieved flux was 5.97 L/m².h, using brine oil field produced water, via PS/PEG/SWCNTs membrane with 0.5 wt% of SWCNTs. Moreover, the membrane indicated sustaining performance stability in the 480 min continuous desalination testing, showing that the synthesized PS/PEG/SWCNTs NC modified membrane may be of magnificent potential to be activated in EDCMD procedure for water desalination.     

Selective Hg2+ sensor performance based various carbon‐nanofillers into CuO‐PMMA nanocomposites

Ternary nanocomposites (NCs) containing copper oxide (CuO)/poly(methyl methacrylate)/various carbon‐based nanofillers have been successfully prepared as thin films by an ex situ method as a selective Hg⁺² sensor. The structural, morphological, and electrochemical properties of the NCs were identified by all common characterization tools. The FT‐IR curves of these NCs proved the efficiency of CuO mixed with single‐walled CNTs (CuO/SWCNTs), multi‐walled CNTs (CuO/MWCNTs), or graphene (CuO/G) nanoparticles in the PMMA polymer matrix. The mixed nanofillers significantly improved the properties of the PMMA film. The thermal characteristics of the pure PMMA polymer matrix were highly developed by adding nanofillers in the form of NCs. The maximum composite degradation temperature (CDT_max) values were comparable for all the NCs and were in the range of 345 to 406°C. For fabrication, the CuO‐PMMA‐SWCNT, CuO‐PMMA‐MWCNT, and CuO‐PMMA‐GNCs were coated onto a glassy carbon electrode (GCE) to form a tiny layer with orderly thickness using a conductive 5% Nafion chemical binder. During the electrochemical investigation, it was found that CuO‐PMMA‐SWCNT had the maximum response toward Hg²⁺ ions compared to the other nanofillers in a buffer medium (phosphate type). To calibrate the Hg²⁺ ionic sensor, the data were plotted against Hg²⁺ ion concentration and the proposed sensor showed linearity over a wide range of concentrations (0.1‐0.01 mM), which is called the linear dynamic range (LDR). The analytical parameters, such as sensitivity (1.70 × 102 μAμM^‐1 cm^?2), detection limit (55.76 ± 2.79 pM), and limit of quantification (185.87 pM) were calculated from the calibration curve. Moreover, it showed good reproducibility, fast response time, good linearity, large LDR, and good stability. The CuO‐PMMA‐SWCNT NC‐modified GCE offers a new route to fabricate novel heavy metal ionic sensors, which might be used in green environment and health development applications.     

Investigation of the curing kinetics of polyurethane/nitrocellulose blends through FT-IR measurements

Polyester (HTPS) based polyurethane (PU) elastomers were currently established to be effective binders for high-energy composites with improved performances. Conventional PU binders are mostly non-energetic materials, and consequently reduce the energy performance significantly. Nitrocellulose (NC), is an energetic polymer widely used as an ingredient in propellants, explosives, fireworks, and gas generators, it may be introduced in PU-based compositions to overcome their performance drawback. Kinetic parameters must be specified in order to build PU binders with the most convenient and appropriate features. Therefore, the cure kinetics of polyester based polyurethane binder systems were investigated by Fourier transform infrared spectroscopy (FT-IR) isothermal method. The polyester prepolymer (Desmophen^® 1200) was cured with hexamethylene diisocyanate (HDI: Desmodur^® N100) at various molar ratios (R_[NCO]/[OH] = 0.6, 1, 1.25, and 1.5) and under different isothermal conditions (T = 60°C, 80°C, 100°C, and 120°C). In addition, the effect of the addition of nitrocellulose on the kinetics of polymerization of PU was investigated. The progression of the reaction was followed based on the decrease of the peak intensity of –NCO group at 2271 cm⁻¹ as a function of the reaction time. The curing kinetic model and the apparent activation energy (E_α) were determined by the use of Kamal autocatalytic model and Friedman isoconversional method, respectively.     

DSC studies on long-term properties of nitrocellulose and SYM-diphenylurea system

Long-term investigations of the phase structure and pore structure of nitrocellulose and sym-diethyldiphenylurea (C1) mixtures were conducted for samples with C1 mass fractions w _C1=0.5, 0.6 and 0.8. The distribution of pore sizes and the composition of the nitrocellulose matrix were determined based on the melting enthalpy of C1. The three kinds of pores was observed with the characteristic size of about 7, 14 and 28 nm. Long-term storage of mixtures caused an increase in size of the smallest pores and a decrease of C1 concentration in the nitrocellulose matrix. The mechanism of changes in pore sizes is presented in term of multi-sheet model of NC fiber. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermochemistry of the binary system nitrocellulose+2,4-dinitrotoluene

Melting enthalpy and mixing enthalpy of binary system 2,4-dinitrotoluene and nitrocellulose were determined by DSC method. The maximum value of mixing enthalpy was H _max ^M=1.38 kJ mol⁻¹ for molar fraction x _w24DNT = 0.501. The Flory-Huggins parameter (c) was estimated. The solubility curves and glass transition temperatures were predicted and compared with the experimental results. The measurements were performed for the samples with different times of storage at room temperature. The analysis of melting peaks for the mixture leads to the conclusion that for the long periods of storage the melting of 2,4-dinitrotoluene takes place in the confined spaces (pores) and unconfined space (bulk). The crystallization and melting is observed during the short time of storage in mixtures with low nitrocellulose content and in the case of mixtures with a large amount of NC the glass transition is additionally observed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis,characterization and kinetic computations of fullerene (C60)–CuO on the mechanism decomposition of ammonium perchlorate

CuO, C₆₀–CuO, and Al/C₆₀–CuO nanostructures were synthesized and characterized by scanning electron microscope (SEM)/energy dispersive spectrometer (EDS), X-ray diffraction (XRD) and fourier transform infrared spectroscopy (FTIR). differential scanning calorimetry (DSC)/thermogravimetric analysis (TGA) measurements were performed to study the influence of these additives on ammonium percolate (AP) thermal decomposition. From the comparison of DSC and TGA plots, the catalytic effect of CuO and C₆₀–CuO has been clearly noticed in which the lower temperature decomposition of AP was decreased from 331 °C to 315 °C, 310 °C, and 303 °C (in the presence of CuO, C₆₀–CuO, and Al/C₆₀–CuO, respectively) and the HTD was dropped from 430 °C (pure AP) to 352 °C, 335 °C, and 317 °C (for the compounds AP/CuO, AP/C₆₀–CuO, and AP/Al/C₆₀–CuO, respectively). The kinetics of the samples were investigated by isoconversional models and compared with an iterative procedure. The results of pure AP indicated a complex decomposition process involving three decomposition steps with specific reaction mechanism. The nanocatalysts incorporated in the AP have clearly affected its decomposition process in which the reaction mechanism and the number of stages were changed.     

不同方法制备的CeO2载体对CuO/CeO2催化剂水煤气变换活性和稳定性的影响

分别采用沉淀法(A), 水热法(B)和柠檬酸溶胶-凝胶法(C)制备了三种CeO2材料, 并以其为载体采用沉积-沉淀法制备了CuO/CeO2催化剂. 运用N2物理吸附、粉末X射线衍射(PXRD)、原位粉末X射线衍射(in situ PXRD)、氢气-程序升温还原(H2-TPR)和循环伏安法(CV)等技术对其进行了表征, 考察了不同方法制备的CeO2载体对CuO/CeO2水煤气变换(WGS)催化剂的结构、氧化-还原性能、催化活性和稳定性的影响. 结果表明, 它们的催化活性和稳定性顺序都是CuO/CeO2-A>CuO/CeO2-B>CuO/CeO2-C. 联系表征结果, CuO/CeO2催化剂的活性与催化剂中CuO的颗粒度、CuO的微观应力和中等大小且与二氧化铈相互作用的CuO的数量等有关, 而这些因素很大程度上受CeO2载体本身的热稳定性的影响. 根据CV中扫描次数的增加, Cu2+←→Cu0氧化还原峰面积减小, 推断CuO/CeO2催化剂在一定条件下氧化还原是不可逆的, 这可能是其在反应气氛下经受温度循环之后活性降低的原因.     

Fruit waste (Pulp) decorated CuO NFs as promising platform for enhanced catalytic response and its peroxidase mimics evaluation

Herein, we report for the first time, an eco-compatible hydrothermal route for the synthesis of carbon enriched mesoporous material (CuO NFs@MP) using fruit waste (Pulp) obtained from Citrus limetta’s (Mausambi) decorated irregular shaped CuO nanoflakes (NFs). The CuO NFs@MP nanocomposite was fully characterized through several spectroscopic-cum-analytical techniques such as TEM and XPS, which further confirmed the presence of CuO NFs. CuO NFs@MP could serve as an excellent catalyst for N-Arylation reaction and also paves promising peroxidase mimic activity. The preliminary results indicated that CuO NFs@MP shows the catalytic advantage of higher yields, shorter reaction time and greener conditions. Simultaneously, the oxidation of colorless TMB with H₂O₂ into blue-green colored ox-TMB was also observed in 60 s with CuO NFs@MP. The present nanocomposite is easy to synthesize, economical, retrievable and a reusable catalyst for synthesizing a varied range of N-Arylated products and could also mimic peroxidase without significant loss of activity.     

Preparation of copper oxide nanosheets by pulsed laser ablation in liquid for anticancer,antioxidant, and antibacterial activities

In this work, the preparation of copper oxide (CuO) nanosheets by laser ablation in water was demonstrated. The optical, structural, stability, and morphological properties of CuO nanosheets were investigated using UV–Vis spectrophotometer, X-ray diffraction (XRD), scanning electron microscope (SEM), and zeta potential (ZP). The XRD results confirm the formation of crystalline (CuO) with a monoclinic phase. The optical energy gap of CuO nanosheets was found to be 2.2 eV at 300 k. The average thickness of the synthesized copper oxide nanosheets is 25 nm. Energy dispersive X-ray result confirms the formation of stoichiometric CuO. The zeta potential result confirms the synthesized CuO colloid is stable. Gram-positive bacteria are found to be more susceptible to CuO nanosheets than Gram-negative bacteria. The synthesized copper oxidenanosheets are tested for antibacterial activity against Gram (+ve) and Gram (-ve) bacteria stains. The results suggest that CuO NPS can give hydrogen atoms and remove the unstable electron from DPPH at a rate of 200 μg/ml than 12.50 μg/ml. The results demonstrate that the copper oxide nanosheets have an effective antioxidant. Furthermore, according to a cytotoxicity assay, when cancer cells are incubated with copper oxide nanosheets, they are unable to grow well. copper oxide nanosheets can induce apoptosis and suppress pancreatic cell proliferation.     

Significantly enhanced electromagnetic interference shielding effectiveness of montmorillonite nanoclay and copper oxide nanoparticles based polyvinylchloride nanocomposites

In the present study, montmorillonite (MMT) nanoclay and copper oxide (CuO) nanoparticles (NPs) reinforced polyvinylchloride (PVC) based flexible nanocomposite films were prepared via solvent casting technique. Using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Scanning electron microscopy (SEM) and thermo-gravimetric analysis (TGA), the structural, morphological and thermal properties of PVC/MMT/CuO nanocomposite films with various loadings of CuO NPs and MMT were investigated. These studies suggested that by the addition of dual nanofillers in the polymer matrix some structural modifications occurred owing to the homogenous dispersion of MMT and CuO NPs within the PVC matrix. The TGA results reveal that the addition of CuO NPs and MMT considerably improved the thermal stability of the nanocomposites. The EMI shielding effectiveness (SE) of nanocomposites was examined in the X-band (8–12 GHz) and Ku-band (12–18 GHz) frequency regions. The EMI SE values were found to be −30 dB (X-band) and −35 dB (Ku-band) for nanocomposites containing 0.3 wt% of CuO NPs and 4.7 wt% of MMT respectively while the shielding was found to be absorption dominant. These results emphasize that PVC/MMT/CuO nanocomposite films can be used as a potential EMI shielding material.     

Ranolazine-functionalized CuO NPs: efficient homogeneous and heterogeneous catalysts for reduction of 4-nitrophenol

In the present study copper oxide nanoparticles (CuO NPs) were synthesized using a hydrothermal method with ranolazine as a shape-directing agent. Ranolazine-functionalized CuO NPs were characterized by various analytical techniques such as scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD). The SEM pattern confirmed the morphology of ranolazine-functionalized CuO NPs with well-defined rice-like structures. FTIR spectroscopy confirmed the interaction between CuO NPs and ranolazine. The XRD analysis indicated that the structure of ranolazine-functionalized CuO NPs was monoclinic crystalline and the size ranged between 9 and 18 nm with an average particle size of 12 nm. The smaller size range of CuO NPs gave a large surface area that enhanced the efficiency of these catalysts employed for the reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) in the H ₂ O system. In homogeneous catalysis, results showed that 50 μL of CuO NPs was required in the presence of NaBH4 for 99% reduction of 4-NP in 240 s. On the other hand, for heterogeneous catalysis, 0.5 mg of CuO NPs was used in the presence of NaBH4 for 99% catalytic reduction of 4-NP to 4-AP in 320 s. The rate of reaction for homogeneous catalysis and heterogeneous catalysis was determined from the plots of In(Ct /C0) of 4-NP versus time (s), which showed good linearity with values of 1.3 × 10 ^-2 and 8.8 × 10 ^-3 s ^-1 . respectively. The high-quality catalytic efficiency, good reusability, nontoxic nature, and low cost are favorable properties of the synthesized CuO NPs for use as efficient catalysts for reduction of 4-AP to 4-NP in both homogeneous and heterogeneous media.     

Thermal characteristics of ammonium nitrate, carbon, and copper(II) oxide mixtures

Ammonium nitrate (AN) has been extensively used as an oxidizer in energetic compositions, and is a promising compound as a propellant and gas generator. It is well-known that metal oxides help to address some of the disadvantages of AN, such as low stability and a low burning rate in these applications. In order to investigate the effects of copper(II) oxide (CuO) on the thermal decompostion of AN mixtures, the thermal characteristics of AN, carbon, and CuO mixtures were measured using simultaneous differential scanning calorimetry and thermogravimetry–differential thermal analysis connected with infrared spectroscopy and mass spectrometry. As a combustible material, activated carbon (AC), and carbon black (CB) were used in this study. In the TG–DTA results for AN/AC/CuO and AN/CB/CuO mixtures in an open cell, an exotherm was observed at approximately 210 and 230 °C, respectively. In addition, the IR and mass spectra of the gases produced from the AN/AC/CuO and AN/CB/CuO mixtures indicated the presence of CO₂. Notably, the effect of CuO addition on the oxidation of the AN/AC/CuO mixture was different from that on the AN/CB/CuO mixture; the oxidation of AC shifted to a lower temperature, while the oxidation of CB shifted to a higher temperature. These results suggest that the effect of CuO on the oxidation of different types of carbon depends on the chemical reactivity of the carbon, which is derived from its physical properties.     

One-pot synthesis of CuO/TiO2 nanocomposites for improved photocatalytic hydrogenation of 4-nitrophenol to 4-aminophenol under direct sunlight

The excellent photocatalytic hydrogenation of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) with NaBH₄ in the aqueous medium is still a big challenge. Herein, we report a facile one-pot evaporation-induced self-assembly (EISA) method to synthesize a series of CuO/TiO₂ nanocomposites. The as-synthesized CuO/TiO₂ photocatalysts exhibit remarkable catalytic activity under direct sunlight in selective hydrogenation of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) due to the synergistic interaction of guest copper nanoparticles with host titanium dioxide (TiO₂) species. Especially, 5 wt% CuO/TiO₂ nanocomposite revealed superior reaction rate constant (k) value (0.306 min⁻¹) when compared to 3 wt% CuO/TiO₂ (0.192 min⁻¹) and 7 wt% CuO/TiO₂ (0.240 min⁻¹). Moreover, several characterization techniques (XRD, TEM, N₂ adsorption–desorption isotherm, DRS, and XPS) were executed to deeply investigate the effect of copper content on the bulk and interfacial properties of the catalysts. The characterization results proved that the superior photocatalytic hydrogenation over 5 wt% CuO/TiO₂ catalyst can be ascribed to moderate CuO loading as well as even dispersion of CuO species on the surface of active TiO₂ host, which can largely improve the light absorption ability within visible light region. Besides, the 5 wt% CuO/TiO₂ catalyst exhibits remarkable recyclability and durability, retaining its superior activity (above 95%) up to several repeating cycles, proving its practical applicability for hydrogenation reactions at domestic and industrial levels.