Reduction of U<Subscript>3</Subscript>O<Subscript>8</Subscript> to U by a metallic reductant,Li

Reduction of U₃O₈ was investigated for the recycling of spent oxide fuel from a commercial nuclear power plant. The possible reduction methods were proposed and compared. Based on the thermodynamic analysis, Li metal was selected as a reductant. The optimum reaction temperature for the reduction of U₃O₈ was investigated at the wider reaction temperature range. The adverse oxidation of U metal by Li₂O at 1,000 °C was experimentally verified. Ellingham diagram was constructed to investigate the extent of the uranium oxides reduction when the reaction was carried out above melting point of U metal.     

Preparation and characterization of luminescent cellulose–Y<Subscript>4</Subscript>Si<Subscript>2</Subscript>O<Subscript>7</Subscript>N<Subscript>2</Subscript>:Ce<Superscript>4+</Superscript> hybrid hydrogels

Novel luminescent bio-based hydrogels comprising cellulose and Y₄Si₂O₇N₂:Ce⁴⁺ (YC) were prepared in an alkali/urea aqueous system using epichlorohydrin as a cross-linker. The structure, characteristics and properties of the hydrogels were investigated by various techniques, including FTIR spectroscopy, wideangle X-ray diffraction, scanning electron microscopy, etc. The results showed that when the content of YC was less than 0.05 g, the YC particles were tightly embedded in the macro porous of cellulose matrix, which not only supplied cavities for YC immobilization, but also supplied the pore wall to protect the structure and character of YC. Hence, the cellulose–YC hybrid hydrogels exhibited strong cyan fluorescence under a UV lamp. However, excess of YC particles were enshrouded in the cellulose matrix resulted in smaller pores, weaker fluorescence intensity, lower swelling ratio and higher mechanical properties.     

The Role of Y<Subscript>2</Subscript>O<Subscript>3</Subscript> and MgO Additives on the Photoluminescence Properties of Si<Subscript>3</Subscript>N<Subscript>4</Subscript> Nanoparticles

The current research addressed synthesizing and studying photoluminescence studies of β-Si₃N₄ nanoparticles. The effect of MgO and Y₂O₃ as the typical additives on photoluminescence behaviour was evaluated. The β-Si₃N₄ with MgO and Y₂O₃ additive specimens were fabricated by a solid state technique (ball-milled method). The as-prepared products were characterized by X-ray diffraction technique, transmission electron microscopy, field emission scanning electron microscopy, energy dispersive X-ray spectroscopy and Raman analysis. The results showed that after ball-milled process, hexagonal β-Si₃N₄ with MgO or Y₂O₃ as the additives with the size distribution of 45–50 nm was obtained. The optical properties of the as-synthesized product were also investigated by photoluminescence and diffuse reflection spectroscopy. The obtained results confirmed that employing MgO as an additive, in comparison to the Y₂O₃, could enhance emission properties in the synthesized silicon nitride nanoparticles. The obtained results also showed that MgO–Si₃N₄ pair acted as FRET system to enhance the emission intensity of β-Si₃N₄ nanoparticles.     

Synthesis and charge-discharge performance of Li<Subscript>5</Subscript>SiN<Subscript>3</Subscript> as a cathode material of lithium secondary batteries

Li₅SiN₃ crystals are synthesized by direct reaction between Li₃N and Si₃N₄ with the molar ratio Li₃N/Si₃N₄ of 10:1. Reaction is performed at 1073 K for 1 h under a nitrogen atmosphere of 700 Torr. The lattice constant determined by the X-ray powder diffraction method is 4.718 Å. Four broad Raman peaks are observed at 196, 286, 580, and 750 cm^?1. By analogy with LiMgN, the broad peak at 580 cm^?1 with a half width of 140 cm^?1 is attributed to homogenously random distribution of Li and Si atoms. The band gap of Li₅SiN₃ is found to be a direct gap of about 2.5 eV by optical absorption and photoacoustic spectroscopy methods. Comparison with the conventional cathode materials for lithium ion batteries, this gap value is close to d-d transition energy of Mn in LiMn₂O₄ (1.63 eV or 2.00 eV) and that of Co in LiCoO₂ (2.1 eV), suggesting that Li₅SiN₃ is a possible cathode material. The 5 × 5 mm²-sized lithium secondary battery of Li₅SiN₃ cathode/propylene carbonate + LiClO₄ electrolyte/Li anode structure shows a discharge capacity of 2.4 μAh cm^?2 for a discharge current of 1.0 μA.     

Bifunctional decamethylcyclohexasilanes X<Subscript>2</Subscript>Si<Subscript>6</Subscript>Me<Subscript>10</Subscript> (X = Cl,H, or OH): molecular and crystal structures and mesomorphic properties

Isomer separation of mixtures, which were prepared by chlorination followed by transformations of dodecamethylcyclohexasilane (Me₂Si)₆ into bifunctional decamethylcyclohexasilanes X₂Si₆Me₁₀ (X = Cl, H, or OH), was carried out. As a result, mixtures of the corresponding 1,3- and 1,4-derivatives were separated to obtain structural isomers, and stereoisomers, viz., cis- and trans-1,4-dihydrocyclohexasilanes, were isolated in individual form. The molecular and crystal structures of the resulting bifunctional decamethylcyclohexanes X₂Si₆Me₁₀ (X = H or OH) and decamethyl-7-oxahexasilanorbornane were established by X-ray diffraction analysis. Bifunctional cyclohexasilanes form a mesophase as a plastic crystal. The temperature range of its existence was determined. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1566–1575, July, 2005.     

Synthesis of Gd<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>FeO<Subscript>3</Subscript> perovskite-type nanopowders for adsorptive removal of MB dye from water

In the present study, nanoparticles of perovskite-type Gd_0.5Sr_0.5FeO₃ (GSFO) were fabricated by a sol–gel method. A series of analytical techniques were used to characterize the crystallinity, morphology, specific surface area and grain size of GSFO powders. The thermal decomposition process of the complex precursor was examined by means of differential thermal analysis–thermal gravimetric analysis. X-ray diffraction results showed that a single perovskite phase was completely formed after calcination at 700 °C. In addition, transmission electron microscopy images revealed that the average size of the particles is approximately 35.23 nm in diameter. The surface morphology and composition of these nanopowders were also investigated using a scanning electron microscope and an energy dispersive X-ray spectrometer. GSFO nanoparticles showed excellent adsorption efficiency towards methylene blue dye in aqueous solution. The adsorption studies were carried out at different pH values, initial dye concentrations, various adsorbent doses and contact time in batch experiments. The dye removal efficiency was found to be increased with increasing the initial pH of the dye solution, and GSFO exhibited good dye removal efficiency at a basic pH, especially at a pH of 12. Experimental results indicated that the adsorption kinetic data follow a pseudo-second-order rate for the tested dye. The isotherm evaluations revealed that the Redlich–Peterson model attained better fits to the experiment's equilibrium data than the Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich models.     

Theoretical study of isomerism of carbonand silicon-substituted aluminum clusters M<Subscript>6</Subscript>Al<Subscript>38</Subscript> and M<Subscript>12</Subscript>Al<Subscript>32</Subscript>

More than twenty M₆Al₃₈ isomers and several M₁₂Al₃₂ isomers of carbon- and silicon-substituted aluminum clusters with six and twelve dopant atoms of general formula M_nA_l44–n(M = C and Si, n = 6 and 12) have been studied by the density functional theory method. Calculations predict that, in the lowest-lying M₆Al₃₈, isomer, all substitutions of C atoms for Al are localized in one outer surface layer of the aluminum cage. In the course of optimization, the C atoms with a negative charge of about 1e are incorporated into positions of the intermediate layer to transform it into a 12-atom face composed of three adjacent vertex-sharing six-membered rings with short C–Al bonds. In the favorable isomer of M₆Al₃₈, the dopants are scattered as individual Si atoms located in both outer layers or in the subsurface space between the outer layers and the inner core of the cluster. Optimization of low-lying isomers with twelve starting substitutions of C and Si for Al in both outer layers has localized two preferable C₁₂Al₃₂ isomers. One of them contains three covalently bonded diatomic C₂ anions, which are combined through bridging aluminum atoms in the three-dimensional [C₆Al₇] cluster inside the severely distorted outer cage. In the second, most favorable, isomer, the dopants are distributed as isolated C anions; together with the bridging Al atoms, they form the [M₁₂Al₃₂] inner cage with an unusual dumbbell-like structure. For M₁₂Al₃₂, the aluminum cage undergoes moderate distortions. The silicon atoms remain in the outer layers and form five-membered ring subclusters [Si₅] and [Si₂Al₃] bound to the neighboring intermediate layers through elongated and weakened Si–Al bonds. Evaluation of the energies of the model exchange reactions Al₄₄ + M₆ → M₆Al₃₈ + Al₆ and Al₄₄ + 2M₆ → M₁₂Al₃₂ + 2A_l6 shows that for M= C both reaction are exothermic, whereas for M = Si the former reaction is nearly isothermal and the second reaction is endothermic and requires significant energy inputs. The differences between the equilibrium structures and the relative positions on the energy scale of the isomers of the C₆Al₃₈–Si₆Al₃₈ and C₁₂Al₃₈–Si₁₂Al₃₈ clusters are examined.     

Study of Fe-doped V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> catalyst for an enhanced NH<Subscript>3</Subscript>-SCR in diesel exhaust aftertreatment

Selective catalytic reduction (SCR) with ammonia has been considered as the most promising technology, as its effect deals with the NO_X. Novel Fe-doped V₂O₅/TiO₂ catalysts were prepared by sol–gel and impregnation methods. The effects of iron content and reaction temperature on the catalyst SCR reaction activity were explored by a test device, the results of which revealed that catalysts could exhibit the best catalytic activity when the iron mass ratio was 0.05%. It further proved that the VTiFe (0.05%) catalyst performed the best in denitration and its NO_X conversion reached 99.5% at 270 °C. The outcome of experimental procedures: Brunauer–Emmett–Teller surface area, X-ray powder diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, temperature-programmed reduction and adsorption (H₂-TPR, NH₃-TPD) techniques showed that the iron existed in the form of Fe³⁺ and Fe²⁺ and the superior catalytic performance was attributed to the highly dispersed active species, lots of surface acid sites and absorbed oxygen. The modified Fe-doped catalysts do not only have terrific SCR activities, but also a rather broad range of active temperature which also enhances the resistance to SO₂ and H₂O.     

Enhancement of the photoluminescence and long afterglow properties of Ca<Subscript>2</Subscript>MgSi<Subscript>2</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>2+</Superscript> phosphor by Dy<Superscript>3+</Superscript> co-doping

The Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺, Dy³⁺ long afterglow phosphors were synthesized under a weak reducing atmosphere by the traditional high temperature solid state reaction method. The synthesized phosphors were characterized by powder X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX) techniques. The luminescence properties were investigated using thermoluminescence (TL), photoluminescence (PL), long afterglow, mechanoluminescence (ML), and ML spectra techniques. The crystal structure of sintered phosphors was an akermanite type structure, which belongs to the tetragonal crystallography. TL properties of these phosphors were investigated, and the results were also compared. Under the ultraviolet excitation, the emission spectra of both prepared phosphors were composed of a broad band peaking at 535 nm, belonging to the broad emission band. When the Ca₂MgSi₂O₇:Eu²⁺ phosphor is co-doped with Dy³⁺, the PL, afterglow and ML intensity is strongly enhanced. The decay graph indicates that both the sintered phosphors contain fast decay and slow decay process. The ML intensities of Ca₂MgSi₂O₇:Eu²⁺ and Ca₂MgSi₂O₇:Eu²⁺, Dy³⁺ phosphors were proportionally increased with the increase of impact velocity, which suggests that this phosphor can be used as sensors to detect the stress of an object.     

Spatial structure and stability of Mo<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript>Si<Subscript><Emphasis Type="Italic">m</Emphasis></Subscript> nanoparticles

By means of the ab initio DMol³ method Mo _n Si _m nanoparticles and fragments of Mo₃Si and MoSi₂ crystal lattices are theoretically modeled. For both crystals a few neutral Mo₄Si₆ and Mo₆Si₆ fragments of different shapes and symmetry are considered. In each case, after cluster separation its geometry is optimized, as a result of which the geometric structure noticeably changes and its stability increases. In order to theoretically search for the spatial configurations of Mo₄Si₆ and Mo₆Si₆ nanoparticle, two approaches are used: 1) in the most stable Fe₄C₆ and Fe₆C₆ isomers found previously, iron and carbon atoms are replaced by molybdenum and silicon respectively and then the geometry is optimized to obtain new equilibrium distances and angles; 2) the search for main Mo₄Si₆ and Mo₆Si₆ configurations is performed using the binominal scheme, starting from Mo₂, MoSi, and Si₂ dimers. The nanoparticle structures are found to contain metal atom chains and isolated pairs and triples of silicon atoms. In most cases, the nanoparticle stability proves to be higher than that of the crystal clusters.     

Electrodeposition of CuGaSe<Subscript>2</Subscript> and CuGaS<Subscript>2</Subscript> thin films for photovoltaic applications

CuGaSe₂ and CuGaS₂ polycrystalline thin film absorbers were prepared by one-step electrodeposition from an aqueous electrolyte containing CuCl₂, GaCl₃ and H₂SeO₃. The pH of the solution was adjusted to 2.3 by adding HCl and KOH. Annealing improved crystallinity of CuGaSe₂ and further annealing in sulphur atmosphere was required to obtain CuGaS₂ layers. The morphology, topography, chemical composition and crystal structure of the deposited thin films were analysed by scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy and X-ray diffraction, respectively. X-Ray diffraction showed that the as-deposited CuGaSe₂ film exhibited poor crystallinity, but which improved dramatically when the layers were annealed in forming gas atmosphere for 40 min. Subsequent sulphurization of CuGaSe₂ films was performed at 400 °C for 10 min in presence of molecular sulphur and under forming gas atmosphere. The effect of sulphurization was the conversion of CuGaSe₂ into CuGaS₂. The formation of CuGaS₂ thin films was evidenced by the shift observed in the X-ray diffraction pattern and by the blue shift of the optical bandgap. The bandgap of CuGaSe₂ was found to be 1.66 eV, while for CuGaS₂ it raised up to 2.2 eV. A broad intermediate absorption band associated to Cr and centred at 1.63 eV was observed in Cr-doped CuGaS₂ films.     

Structure and lithium mobility of Li<Subscript>4</Subscript>Pt<Subscript>3</Subscript>Si

The lithium-rich silicide Li₄Pt₃Si was synthesised from the elements by high-temperature synthesis in a sealed niobium ampoule. Its structure was refined on the basis of single-crystal X-ray diffraction data: R32, a = 693.7(2), c = 1627.1(4) pm, wR2 = 0.0762, 525 F² values and 21 variables. The striking structural motifs of the Li₄Pt₃Si structure are silicon atoms with a slightly distorted trigonal prismatic platinum coordination with short Si–Pt distances (238–246 pm). Always two trigonal prisms are condensed via a common Pt₃ triangle, and these double units built up a three-dimensional network by condensation via common corners. The channels left by this prismatic network are filled by two crystallographically independent lithium sites in a 3:1 ratio. The single crystal X-ray data were fully confirmed by neutron powder diffraction and ⁷Li magic-angle spinning (MAS)–nuclear magnetic resonance (NMR) results. The two distinct lithium sites are well differentiated by their ⁷Li isotropic chemical shift and nuclear electric quadrupolar interaction parameters. MAS-NMR spectra reveal signal coalescence effects above 300 K, indicating chemical exchange between the lithium sites on the millisecond timescale. The spectra can be simulated with a simple two-site exchange model. From the resulting temperature-dependent correlation times, an activation energy of 50 kJ/mol is extracted.     

Carbon ceramic electrodes modified with mixed oxides SiO<Subscript>2</Subscript>/SnO<Subscript>2</Subscript> for determination of levofloxacin

The preparation of a carbon ceramic electrode modified with SnO₂ (CCE/SnO₂) using tin dibutyl diacetate as precursor was optimized by a 2³ factorial design. The factors analyzed were catalyst (HCl), graphite/organic precursor ratio, and inorganic precursor (dibutyltin diacetate). The statistical treatment of the data showed that only the second-order interaction effect, catalyst × inorganic precursor, was significant at 95% confidence level, for the electrochemical response of the system. The obtained material was characterized by scanning electron microscopy (MEV), X-ray diffraction (XRD), RAMAN spectroscopy, XPS spectra, and voltammetric techniques. From the XPS spectra, it was confirmed the formation of the Si–O–Sn bond by the shift in the binding energy values referred to Sn 3d3/2 due to the interaction of Sn with SiOH species. The incorporation of SnO₂ provided an increment of the electrode response for levofloxacin, with Ipa = 147.0 μA for the ECC and Ipa = 228.8 μA for ECC/SnO₂, indicating that SnO₂ when incorporated into the silica network enhances the electron transfer process. Under the optimized working conditions, the peak current increased linearly with the levofloxacin concentration in the range from 6.21×10^?5 to 6.97×10^?4 mol L^?1 with quantification and detection limits of 3.80×10^?5 mol L^?1 (14.07 mg L^?1) and 1.13×10^?5 mol L^?1 (4.18 mg L^?1), respectively.     

Synthesis and study of the phosphate Cs<Subscript>2</Subscript>Mn<Subscript>0.5</Subscript>Zr<Subscript>1.5</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>

The new phosphate Cs₂Mn_0.5Zr_1.5(PO₄)₃ was synthesized for the first time and characterized by X-ray diffraction. Its crystal structure was refined in space group P2₁3, Z = 4 at 25°C (a = 10.3163(1) Å, V = 1097.93(1) ų), by the Rietveld method using the powder X-ray diffraction data. The structure is built of an octahedral-tetrahedral framework {[Mn_0.5Zr_1.5(PO₄)₃]^2?}_3∞ with cesium atoms being located in large cavities. The hydrolytic stability of the powdered phosphate containing ¹³⁷Cs radionuclide was studied. The minimum achieved ¹³⁷Cs leaching rate was 4 × 10^?8 g/cm₂ day.     

Synthesis,structures, IR spectra,and thermal characteristics of compounds of general formula Ba(M<Stack><Subscript>2/3</Subscript><Superscript>III</Superscript></Stack>U<Subscript>1/3</Subscript>)O<Subscript>3</Subscript> (M<Superscript>III</Superscript> = Sc,Y, In,Nd-Lu)

Compounds with the composition Ba(M _2/3 ^III U_1/3)O₃ (M^III = Sc, Y, In, Nd-Lu) were synthesized by high-temperature solid-state reactions. The structures of the compounds were studied by X-ray diffraction analysis, including the high-temperature method, and IR spectroscopy.     

Effect of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> addition on structure and magnetic properties of Ni<Subscript>0.5</Subscript>Zn<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanofibers

Ni_0.5Zn_0.5Fe₂O₄ nanofibers with addition of 0–5 wt% Bi₂O₃ were synthesized by calcination of the electrospun polyvinylpyrrolidone/inorganic composite nanofibers at the temperature below the melting point of Bi₂O₃. The effects of Bi₂O₃ addition on the phase structure, morphology and magnetic properties of the nanofibers were investigated by means of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy, selected area electron diffraction and vibrating sample magnetometer. It is found that the nanofiber diameter, crystallite size and magnetic parameters can be effectively tuned by simply adjusting the amount of Bi₂O₃ addition. The average diameter of Ni_0.5Zn_0.5Fe₂O₄ nanofibers doped with different contents of Bi₂O₃ ranges from 40 to 63 nm and gradually decreases with increasing Bi₂O₃ content. The addition of Bi₂O₃ does not induce the phase change and all the samples are a single-phase spinel structure. The amorphous Bi₂O₃ tends to concentrate on the nanoparticle surface and/or grain boundary and can retard the particles motion as well as the grain growth, resulting in a considerable reduction in grain size compared to the pristine sample. The specific saturation magnetization and coercivity of the nanofibers gradually decrease with the increase of Bi₂O₃ amount. Such behaviors are explained on the basis of chemical composition, surface effect, domain structure and crystal anisotropy.     

Preparation of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by mechanical alloying and annealing for sensitizing C-modified TiO<Subscript>2</Subscript> and acquirement of efficient photocatalyst

ZnFe₂O₄ nanoparticles sensitized by C-modified TiO₂ hybrids (ZnFe₂O₄–TiO₂/C) were successfully prepared by a feasible method. The ZnFe₂O₄ nanoparticles were prepared by mechanical alloying and annealing. The residual organic compounds in the synthetic process of TiO₂ were selected as the carbon source. The as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, transmission electron microscopy, X-ray photoelectron spectroscopy, ultraviolet–visible light diffuse reflectance spectroscopy (UV–Vis) and N₂ adsorption–desorption analysis. The photocatalytic activity of the photocatalysts was measured by degradation of methyl orange under ultraviolet (UV) light and simulated solar irradiation, respectively. The results show that the carbon did not enter the TiO₂ lattice but adhered to the surface of TiO₂. The photocatalytic activity of the as-prepared C-modified TiO₂ (TiO₂/C) improved both under UV and simulated solar light irradiation, but the improvement was not dramatic. Introduction of ZnFe₂O₄ into the TiO₂/C could enhance the absorption spectrum range. The ZnFe₂O₄–TiO₂/C hybrids exhibited a higher photocatalytic activity both than that of the pure TiO₂ and TiO₂/C under either UV or simulated solar light irradiation. The complex synergistic effect plays an important role in improving the photocatalytic performance of ZnFe₂O₄–TiO₂/C composites. The optimum photocatalytic performance was obtained from the ZnFe₂O₄(0.8 wt%)–TiO₂/C sample.     

Crystallization kinetics and thermal stability of an amorphous Fe<Subscript>77</Subscript>C<Subscript>5</Subscript>B<Subscript>4</Subscript>Al<Subscript>2</Subscript>GaP<Subscript>9</Subscript>Si<Subscript>2</Subscript> bulk metallic glass

The thermal stability, kinetics and glass forming ability of an Fe₇₇C₅B₄Al₂GaP₉Si₂ bulk amorphous alloy have been studied by differential scanning calorimetry. The activation energy, frequency factor and rate constant corresponding to the multiple crystallization steps were determined by the Kissinger method. X-ray diffraction and transmission electron microscopy studies revealed that the crystallization starts with the primary precipitation of α-Fe from the amorphous matrix. The kinetics of nucleation of the α-Fe nanoparticles was investigated by two different methods, i.e. isothermal annealing and continuous heating after partial annealing.     

A study of the electronic structure of polyvinylsiloxane (CH<Superscript>2</Superscript>CHSiO<Subscript>1.5</Subscript>)<Subscript><Emphasis Type="Italic">n</Emphasis></Subscript> by X-ray photoelectron spectroscopy and quantum chemical modeling in the DFT approximation

The electronic structure of polyvinylsiloxane polymeric chains (Si₂O₃(CHCH₂)₂)_n is studied by X-ray photoelectron spectroscopy and quantum chemistry in the DFT approximation. The binding energy of C and O ls electrons occupying inequivalent positions in the polymer coincides within the experimental accuracy. The binding energies for C and O (284.9 eV and 532.4 eV) and for Si2p-electrons (102.7 eV) well agree with the values for related compounds. The experimental data for the binding energy are reproduced in HF and DFT calculations only with the extended 6–311**(d) basis set. The highest occupied levels of the polymer are fy orbitals of vinyl groups