Improving the hydrophilic and antifouling properties of poly(vinyl chloride) membranes by atom transfer radical polymerization grafting of poly(ionic liquid) brushes

In this study, poly(1‐butyl‐3‐vinylimidazolium bromide) (PBVIm‐Br) was grafted onto the poly(vinyl chloride) (PVC) membrane surface via a 2‐step atom transfer radical polymerization (ATRP) reaction. Poly(2‐hydroxyethylmethacrylate) (PHEMA) was grafted onto the membrane surface by aqueous ATRP reaction; then, BVIm‐Br was introduced onto the surface of the PHEMA‐modified PVC membrane through traditional ATRP reaction. The analysis of surface chemistry confirmed the successful grafting of PHEMA and PBVIm‐Br on PVC membrane surface, and the grafting density (GD) of PBVIm‐Br gradually increased as the grafting time was prolonged. The modified membrane exhibited a positive charge and significantly enhanced surface hydrophilicity. The static water contact angle of the membrane surface decreased from 92.3° to 51.6° as the GD of the PBVIm‐Br brushes increased. Filtration experiments indicated that the water flux of the modified membrane increased with increasing GD, and their recovered fluxes were more than twice than the original. In addition, the total fouling ratio of the membranes decreased from 89% in M0 to 67% in M5, and most of the fouling was reversible as the GD of PBVIm‐Br brushes increased. These results indicated that the positive charged poly(ionic liquid) brushes featuring hydrophilic properties would have potential applications in membrane separation.     

Phase separation and crystallinity in proton conducting membranes of styrene grafted and sulfonated poly(vinylidene fluoride)

A series of proton exchange membranes have been prepared by the preirradiation grafting method. Styrene was grafted onto a matrix of poly(vinylidene fluoride) (PVDF) after electron beam irradiation. Part of the samples was crosslinked with divinylbenzene (DVB) or bis(vinylphenyl)ethane (BVPE). Subsequent sulfonation gave membranes grafted with poly(styrene sulfonic acid) and marked PVDF‐g‐PSSA. It was found that the intrinsic crystallinity of the matrix decreased in both the grafting and the sulfonation reaction in all the membranes. The graft penetration and the ion conductivity are influenced strongly by the crosslinker. The ion conductivity is considerably lower in crosslinked membranes than in noncrosslinked ones. Generally, the mechanical strength decreases with crosslinking. The membranes show a regular phase separated structure in which the sulfonated grafts are incorporated in the amorphous parts of the matrix polymer. The phase separated domains are small, of the order of magnitude of 100–250 nm. These were resolved on transmission electron micrographs and on atomic force images but could not be resolved with microprobe Raman spectroscopy. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1741–1753, 1999     

Multiblock copolymers of poly(2,5‐benzophenone) and disulfonated poly(arylene ether sulfone) for proton‐exchange membranes. I. Synthesis and characterization

Nanophase‐separated, hydrophilic–hydrophobic multiblock copolymers are promising proton‐exchange‐membrane materials because of their ability to form various morphological structures that enhance transport. A series of poly(2,5‐benzophenone)‐activated, telechelic aryl fluoride oligomers with different block molecular weights were successfully synthesized by the Ni(0)‐catalyzed coupling of 2,5‐dichlorobenzophenone and the end‐capping agent 4‐chloro‐4′‐fluorobenzophenone. These telechelic oligomers (hydrophobic) were then copolymerized with phenoxide‐terminated, disulfonated poly(arylene ether sulfone)s (hydrophilic) by nucleophilic, aromatic substitution to form hydrophilic–hydrophobic multiblock copolymers. High‐molecular‐weight multiblock copolymers with number‐average block lengths ranging from 3000 to 10,000 g/mol were successfully synthesized. Two separate glass‐transition temperatures were observed via differential scanning calorimetry in the transparent multiblock copolymer films when each block length was longer than 6000 g/mol. Tapping‐mode atomic force microscopy also showed clear nanophase separation between the hydrophilic and hydrophobic domains and the influence of the block length as it increased from 6000 to 10,000 g/mol. Transparent and creasable films were solvent‐cast and exhibited moderate proton conductivity and low water uptake. These copolymers are promising candidates for high‐temperature proton‐exchange membranes in fuel cells, which will be reported separately in part II of this series. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 284–294, 2007     

Surface grafting on poly(ethylene terephthalate) track‐etched microporous membrane by activation with trifluorotriazine: Application to the biofunctionalization with GRGDS peptide

A two‐step wet chemistry protocol has been developed for the surface derivatization of poly(ethylene terephthalate) (PET) track‐etched membrane used as cell culturing support, that is, (a) activation by trifluorotriazine (1 M in acetonitrile (ACN), 30 °C, 3 h); (b) coupling to amine‐terminated molecules, namely 3,5‐bis(trifluoromethyl)benzylamine ((F)Tag), (L)‐4,5‐[³H]‐lysine, and Gly‐Arg‐Gly‐Asp‐Ser (GRGDS) pentapeptide (10^?3 M in PB‐ACN, 1:1 (v/v), 20 °C, 17 h). The grafting rates determined by X‐ray photoelectron spectroscopy, from the F/C and N/C atomic ratios, are in the range of 100–140 pmol/cm² (apparent surface), whereas the liquid scintillation counting assays give higher values (180–230 pmol/cm²) corresponding to the open surface reactivity. PET‐g‐(F)Tag is reasonably stable under two usual sterilization conditions of biomaterials, that is, steam heating at 121 °C and γ‐irradiation at 25 kGy. On the other hand, PET‐g‐GRGDS is found to be stable only under ionization radiation (84% of remaining peptide molecules), but damaged in a large extent by the autoclave treatment (23% of remaining peptide molecules). The surfaces of the sterilized PET and PET‐g‐GRGDS samples have been characterized by water contact angle measurement and by atomic force microscopy analysis in air and under water. Comparatively to the corresponding nonsterilized surfaces, γ‐irradiated surfaces are slightly more hydrophilic and also slightly more rough and jagged. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 195–208, 2010     

Improvement of pore geometry and performances of poly(ethylene terephthalate) track membranes by a protective layer method using plasma-induced graft polymerization of 1H,1H,2H-perfluoro-1-octene monomer

The process of geometrical modification of pores in poly(ethylene terephthalate) track-etched membranes (TM) by use of plasma deposition of a fluorine-containing polymer protective layer on one membrane surface and alkali etching of the other surface has been studied in order to produce membranes with improved performance characteristics. Samples of membranes with conical pores have been obtained which have better filtration efficiency compared with initial TM with cylindric pores. Plasma polymerization of 1H,1H,2H-perfluoro-1-octene at the membrane surface was used to produce the protective layer resistant to alkali solutions. The occurrence of plasma modification and changing of pore geometry have been verified by X-ray photoelectron spectroscopy and scanning electron microscopy studies. The filtration efficiency and selectivity of the modified membranes have been studied.     

An effective cross-linking of polymer layer on monodisperse, poly(maleic anhydride-styrene)-modified colloidal silica particles and properties of the composite

Summary  The cross-linkings of the surface polymer layer on mono disperse, poly(maleic anhydride-styrene)-modified silica particles by the reaction with diisocyanate were studied. The extent of cross-linking was estimated by the weight decrease by immersing the particles in the buffer solution of pH 2.0, 4.0 and 9.0 at a room temperature for 24 h. The reaction of the polymer-modified silica with 1,6-diisocyanatohexane afforded relatively stable composite particles which lost less than 5 wt% of the polymer in aqueous solution in the pH range 2.0–9.0. The diisocyanate was a preferable cross-linker to 2,4-diisocyanatotoluene in terms of stability in acidic or basic aqueous solution. The flexibility of the cross-linker molecule possibly plays an important role in the cross-linking reaction. The carboxyl and amino groups were formed by treating the cross-linked composite particles with diluted HCl solution; 5–6 and 0.5–1.1 μmol g^-1, respectively. The cross-linked composite particles exhibited the characteristic property of ζ-potential, −44 to −47 mV and −102 to −107 mV in a neutral aqueous solution and ethanol, respectively. Received: 26 May 1997 Accepted: 4 August 1997     

Synthesis of dual‐functional poly(6‐azidohexylmethacrylate) brushes by a RAFT agent carrying carboxylic acid end groups

Novel types of dual‐functional surface‐attached polymer brushes were developed by interface‐mediated reversible addition‐fragmentation chain transfer (RAFT) polymerization of 6‐azidohexylmethacrylate using the surface‐immobilized RAFT agent and the free initiator. The interface‐mediated RAFT polymerization produced silicon substrate coated with dual‐functional (azido groups from monomer and carboxylic acid groups from RAFT agent) poly(6‐azidohexylmethacrylate) [poly (AHMA)] with a grafting density as high as 0.59 chains/nm². Dual‐functional polymer brushes can represent an attractive chemical platform to deliberately introduce other molecular units at specific sites. The azido groups of the poly(AHMA) brushes can be modified with alkyl groups via click reaction, known for their DNA hybridization, while the carboxylic acid end groups can be reacted with amine groups via amide reaction, known for their antifouling properties. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1696–1706