Differential Pulse Adsorptive Stripping Voltammetric Determination of Chlorpyrifos at a Sepiolite Modified Carbon Paste Electrode

Abstract

An adsorptive stripping voltammetric (AdSV) method for the determination of organophosphorus insecticide chlorpyrifos at a bare carbon paste electrode (CPE) and clay modified carbon paste electrode (CMCPE) was developed. A systematic study of various experimental conditions, such as the pH, accumulation variables and composition of a modifier on the adsorptive stripping response, were examined by using differential pulse voltammetry. A significant improvement was observed in the sensitivity by using the present method with CMCPE. When CMCPE was used, a linear response was obtained over the concentration range 0.0001–2.0 ppm with lower detection limit of 0.00008 ppm, at an accumulation time of 80 s. The interference from other herbicides and ions on the stripping signal of the compound was also evaluated. The described method was applied to estimate the chlorpyrifos in environmental samples.     

Adsorptive stripping behaviour of mitoxantrone on carbon paste electrodes

The electrooxidation of mitoxantrone (MXT) on carbon paste electrodes was studied using voltammetric techniques in adsorption conditions. The analyte was accumulated at the working electrode (a carbon paste electrode) under precisely controlled mass-transport conditions and stripped electrochemically in the same solution. An electrode pretreatment is proposed which shows good reproducibility of the analytical signal (0.81%). The stripping step was studied with alternating current voltammetry providing a linear response in the concentration range 5 x 10(-11) to 7 x 10(-10)M in aqueous samples. Finally, a method using the medium exchange and AC phase-selective adsorptive stripping voltammetry technique was proposed for MXT analysis in urine samples.     

Adsorptive potentiometric stripping analysis of trace tamoxifen at a glassy carbon electrode

A highly sensitive adsorptive stripping procedure for trace measurement of the anticancer drug tamoxifen is described. The method is based on controlled adsorptive accumulation of the drug at an electrochemically treated glassy carbon electrode, followed by chronopotentiometric measurement of the surface species. The chronopotentiometric operation effectively addresses the large background contribution inherent to the glassy carbon electrode to yield a detection limit of 4 x 10(-10) M after 4 min preconcentration. The adsorptive stripping response is evaluated with respect to electrode type and conditioning, accumulation potential and time, stripping current, pH, drug concentration, potential interferences, and other variables. Applicability to urine samples is illustrated.     

Electrochemical adsorptive behavior of some fluoroquinolones at carbon paste electrode.

Cyclic voltammetry and differential pulse voltammetry were used to explore the adsorption behavior of three antibacterial agents at a carbon paste electrode. The drugs were accumulated on a carbon paste electrode, and a well-defined oxidation peak was obtained in acetate buffer (pH 5.0). The adsorptive stripping response was evaluated as a function of some variables such as the scan rate, pH and accumulation time. A simple, precise, inexpensive and sensitive voltammetric method has been developed for the determination of the cited drugs (Lomefloxacin (LFX), Sparfloxacin hydrochloride (SFX), and Gatifloxacin (GFX)). A linear calibration was obtained from 2 x 10(-7) M to 4 x 10(-5) M for LFX, 2 x 10(-7) M to 6 x 10(-5) M for SFX, and GFX. The limits of detection (LOD) were 4.2 x 10(-7), 7 x 10(-7) and 6.6 x 10(-7) M, while the limits of quantification (LOQ) were 1.4 x 10(-6), 2.3 x 10(-6) and 2.2 x 10(-6) M for LFX, SFX, and GFX, respectively. The R. S. D. of five measurements at the 1 x 10(-6) M level were 0.4, 0.5 and 0.3 for LFX, SFX and GFX, respectively. The method was applied to the determination of LFX, SFX and GFX in dilute urine samples and dosage forms, and compared with the HPLC method.     

Determination of dinoseb by adsorptive stripping voltammetry using a mercury film electrode

An adsorptive stripping voltammetric method for the determination of the pesticide dinoseb (2-sec.-butyl-4,6-dinitrophenol) at the mercury film electrode is described. The deposition of the mercury film on a glassy carbon disk electrode was optimized. The temperature, at which the mercury film was deposited, was demonstrated to have a strong influence on the stripping peaks, the first one being much more intense than the second. A systematic study of the variables affecting the stripping response was carried out by differential pulse voltammetry. The results obtained have been compared with those at the HMDE; a significant improvement in the sensitivity of the method developed with the MFE was observed. Using a 300 s accumulation time, the limits of determination and detection were 3.6 × 10^–10 and 1.1 × 10^–10 mol L^–1, respectively. The effect of the presence of several herbicides on the dinoseb response was also tested. The method has been applied to the determination of the pesticide in spiked apple juice at two concentration levels: 12.0 and 1.2 g L^–1 of juice.     

Trace measurements of colchicine by adsorptive stripping voltammetry

A highly sensitive voltammetric method for trace measurements of the alkaloid colchicine is described. The method is based on the controlled adsorptive accumulation of the drug at the hanging mercury drop electrode, followed by voltammetric determination of the surface species. The adsorptive stripping response is evaluated with respect to preconcentration time and potential, solution pH, voltammetric waveform and other variables. With a 10-min preconcentration, a detection limit of 1.3 x 10(-10)M is obtained. The relative standard deviation (at the 1 x 10(-7)M level) is 1.1%. Applicability to urine analysis is illustrated.     

Adsorptive stripping measurements of germanium(IV) in the presence of pyrogallol

The adsorptive stripping voltammetric determination of germanium(IV) based on the adsorptive accumulation of the germanium(IV)-pyrogallol complex on a hanging mercury drop electrode is reported. The reduction current of the adsorbed germanium complex is measured by differential-pulse cathodic stripping voltammetry. The peak potential is at -0.42 V vs. Ag AgCl (saturated KCL). The effects of various parameters (ligand concentration, supporting electrolytic composition and concentration, accumulation potential and collection time) on the response are discussed. With controlled accumulation for 3 min, the detection limit is 1.2 x 10(-9) M germanium. The relative standard deviation (at 1.2 x 10(-8) M germanium) is 3.6%. Possible interferences are evaluated. The applicability of the method to the determination of germanium(IV) in ore samples was also successfully carried out.     

Use of adsorptive square-wave anodic stripping voltammetry at carbon paste electrode for the determination of amlodipine besylate in pharmaceutical preparations

The antihypertensive drug amlodipine has been characterized voltammetrically in a carbon paste electrode by means of anodic stripping voltammetry. An adsorptive stripping method in a carbon paste electrode for trace determination of amlodipine has been described. Cyclic voltammetric studies indicated the oxidation of amlodipine besylate at the electrode surface through a single two-electron irreversible step fundamentally controlled by adsorption. A study of the variation in the peak current with solution variables such as pH, ionic strength, concentration of amlodipine, possible interference, and instrumental variables, such as preconcentration time and accumulation potential, has resulted in the optimization of the oxidation signal for analytical purposes. By anodic adsorptive anodic stripping voltammetry, the calibration plot was linear in the range 9.9 × 10^?9 ? 1.4 × 10^?7 M with a detection limit of 2 × 10^?10 M in a carbon paste electrode at pH 11.0. The procedure was successfully applied to the assay of amlodipine besylate in some commercial products in the market (Amlopres®, Amlodipine, and Norvasc®). The percentage recoveries were in agreement with those obtained by the reference method.     

Trace measurements of the antineoplastic agent methotrexate by adsorptive stripping voltammetry

An extremely sensitive voltammetric method is presented for trace measurement of the cancer chemotherapy drug methotrexate. The method is based on controlled adsorptive preconcentration of methotrexate on the hanging mercury-drop electrode, followed by voltammetric determination of the surface species. Cyclic voltammetry was used to explore the interfacial behaviour. The adsorptive stripping response was evaluated with respect to preconcentration time and potential, pH, concentration dependence, stripping mode, possible interferences, and other variables. The detection limit found was 2 x 10(-9)M (5-min preconcentration), the response was linear, and the relative standard deviation (at the 1.6 x 10(-7)M level) 2.2%. Sensitive adsorptive stripping measurements were also obtained by use of a carbon-paste disk electrode. Applicability to urine analysis is illustrated.     

Quantification of terbutaline in pharmaceutical formulation and human serum by adsorptive stripping voltammetry at a glassy carbon electrode

The electrochemical oxidative behavior of terbutaline at the glassy carbon electrode was studied in a series of the Britton-Robinson buffer of pH 2--11. Cyclic and square-wave voltammograms of terbutaline at the pH values 相似文献   

Stripping Voltammetry of Cerium(IIl) with a Chemically Modified Carbon Paste Electrode Containing Functionalized Nanoporous Silica Gel

This research introduces the design of an adsorptive stripping voltammetric method for the cerium(III) determination at a carbon paste electrode, chemically modified with dipyridyl‐functionalized nanoporous silica gel (DPNSG‐CPE). The electroanalytical procedure comprised two steps: the Ce(III) chemical accumulation at ?200 mV followed by the electrochemical detection of the Ce(III)/dipyridyl complex, using anodic stripping voltammetry. The factors, influencing the adsorptive stripping performance, were optimized including the modifier quantity in the paste, the electrolyte concentrations, the solution pH and the accumulation potential or time. The resulting electrode demonstrated a linear response over a wide range of Ce(III) concentration (1.0–28 ng mL^?1). The precision for seven determinations of 4 and 10 ng mL^?1 Ce(III) was 3.2% and 2.5% (relative standard deviation), respectively. The prepared electrode was used for the cerium determination in real samples and very good recovery results were obtained.     

Voltammetric measurement of haloperidol following adsorptive accumulation at glassy-carbon electrodes

A sensitive stripping voltammetric method is reported for trace measurement of the psychotherapeutic drug haloperidol. The method is based on adsorptive preconcentration of haloperidol on the glassy-carbon electrode in an open circuit, followed by medium exchange and voltammetric determination of surface species. Cyclic voltammetry was used to explore the adsorptive behaviour and the results obtained suggest that the adsorption of haloperidol corresponds to the Frumkin-type isotherm. The adsorptive stripping response was evaluated with respect to stripping mode, electrolyte. pH, preconcentration time, concentration dependence, possible interference and other variables. The detection limit was 1.3 x 10(-9)M (10 min preconcentration) and the response was linear. The relative standard deviation (at the 1.3 x 10(-6)M level) was 2.3%. Applicability to a patient's urine sample is illustrated.     

Differential pulse anodic stripping voltammetric determination of lead(II) with a 1,4-bis(prop-2'-enyloxy)-9,10-anthraquinone modified carbon paste electrode

A sensitive and selective method for the determination of lead(II) with a 1,4-bis(prop-2'-enyloxy)-9,10-anthraquinone (AQ) modified carbon paste electrode has been developed. The method is based on non-electrolytic preconcentration via complex formation with modifier, followed by an accumulation period with a negative potential (-1.5 V), and then by a proper anodic stripping. The analytical performance was evaluated with respect to the quantity of modifier in the paste, concentration of electrolyte solution, preconcentration time, lead(II) concentration, and other variables. A linear calibration graph was obtained in the concentration range 2.00x10(-9)-1.06x10(-5) M Pb(II) (n=21, r=0.9999) with 30 s preconcentration time. The detection limit was found to be 1x10(-9) M. For eight preconcentration/determination cycles, the differential pulse voltammetric response was reproduced with 5.0 and 3.7% relative standard deviations at 2.00x10(-8) and 2.00x10(-6) M Pb(II), respectively. Rapid and convenient renewal of electrode surface allows the use of a single modified electrode surface in multiple analytical determinations over several weeks. Many coexisting metal ions had little or no effect on the determination of lead(II). The developed method was applied to lead determination in waste waters.     

Trace measurement of dipyridamole by adsorptive stripping voltammetry

A sensitive adsorptive stripping voltammetric method for trace measurement of dipyridamole in alkaline solution is described. The method is based on the adsorptive accumulation of the drug at the hanging mercury drop electrode, followed by linear sweep voltammetric determination. The response is evaluated with respect to percentage of ethanol, preconcentration time and potential, and concentration of NaOH. The detection limit of 1.0 x 10(-9)M is obtained under optimized conditions with a 5-min preconcentration. Applicability to injection, tablets and urine analysis is illustrated.     

Determination of aluminium in tree samples by cathodic adsorptive stripping voltammetry

This paper presents a method of determination of aluminium in tree samples (wood, leaves, roots) based on the cathodic adsorptive stripping voltammetry. Al(III) complexed with alizarin S was determined by ASV method using a hanging mercury drop electrode. Optimal conditions were found to be: accumulation time 30-90 s, accumulation potential - 0.70 V versus SCE, supporting electrolyte 0.1 M ammonia-ammonium chloride buffer at pH 8.2 and concentration of alizarin 1 x 10(-5) M. The response of the system, a linear current-concentration relationship was observed up to 8 x 10(-6) M. The developed method has been tested by analysing international reference materials (BCR 62 Olive leaves and BCR 101 spruce needles).     

Determination of Salbutamol in Pharmaceutical and Serum Samples by Adsorptive Stripping Voltammetry on a Carbon Paste Electrode Modified by Iron Titanate Nanopowders

This study introduces a fast and direct electrochemical method for the determination of salbutamol using an iron titanate nanopowder‐modified carbon paste electrode. The electrochemical behavior of salbutamol was studied by differential pulse adsorptive stripping voltammetry. Factors affecting the performance of the adsorptive stripping such as the modifier percent, the electrolyte pH and accumulation time and potential were optimized. The resulting electrode exhibited a linear response in the range of 0.2–25 nM of salbutamol with a detection limit of 90 pM. The proposed method was successfully applied to determine salbutamol in pharmaceutical formulations and human blood plasma.     

Adsorptive stripping voltammetric measurements of trace levels of uranium following chelation with mordant blue 9

The chelate of uranium with the azo dye Mordant Blue 9 is shown to be adsorbed and then reduced on the hanging mercury drop electrode. These properties have been exploited in developing a highly sensitive stripping voltammetric procedure for trace determination of uranium. With controlled adsorptive accumulation for 5 min, a detection limit near 2 x 10(-10)M uranium is obtained. Cyclic voltammetry has been used to characterize the interfacial and redox behaviour. The effect of various operational parameters on the stripping response is discussed. Experimental conditions include use of 1 x 10(-6)M Mordant Blue 9 in 0.05M acetate buffer (pH 6.5), an accumulation potential of -0.43 V, and a linear potential scan. The response is linear up to 1.2 x 10(-7)M uranium, and the relative standard deviation at 4.2 x 10(-8)M is 3.2%. The effects of possible interferences from organic surfactants or metal ions have been investigated.     

Carbon paste electrode for trace zirconium(IV) determination by adsorption voltammetry.

A very sensitive and selective procedure was developed for trace measurement of zirconium based on the cathodic adsorptive stripping voltammetry of the zirconium-alizarin red S(ARS) complex at a carbon paste electrode (CPE). The 2nd-order derivative linear scan voltammograms of the zirconium-ARS complex were recorded by a model JP-303 polarographic analyzer from 0.0 to -1.0 V (vs. SCE). Optimal analytical conditions were found to be: an acetic acid (0.1 mol l(-1))-potassium biphthalate (0.08 mol l(-1)) buffer solution (pH 4.8) containing 4.0 x 10-6 mol l(-1) ARS; accumulation potential, 0.0 V; accumulation time, 180 or 90 s; rest time, 10 s; scan rate, 250 mV s(-1). The results showed that the complex can be adsorbed on the surface of the CPE, yielding one peak at -0.51 V, corresponding to the reduction of ARS in the complex at the electrode. The detection limit was found to be 1.0 x 10(-10) mol l(-1) (S/N = 3) for 240 s accumulation. The linear range was 2.0 x 10(-10)-4.0 x 10(-7) mol l(-1). The developed method was applied to the determination of trace zirconium in the ore samples with satisfactory results.     

茜素修饰碳糊电极吸附伏安法测定痕量铜

报道了采用茜素修饰碳糊电极测定痕量铜的阳极溶出伏安法。在浓度为0 .1 mol/L 的 HAc- Na Ac缓冲溶液 (p H4.5)中 ,于 +0 .1 0 V处富集 ,- 0 .30 V还原后再进行阳极化扫描 ,于 - 0 .0 5V处获得一灵敏的铜的溶出峰 ,二次导数峰电流与铜浓度在 1 .6× 1 0 -9mol/L～ 4.7× 1 0 -7mol/L范围内呈线性关系 ,检出限达 8.0× 1 0 -10 mol/L。同时 ,对电极反应机理进行了讨论。方法应用于锌合金中铜的测定。     

A highly sensitive method for determination of paracetamol by adsorptive stripping voltammetry using a carbon paste electrode modified with nanogold and glutamic acid

A reliable and simple sensor was fabricated by modifying a carbon paste electrode with nanosized gold particles and poly (glutamic acid) for determination of paracetamol (PAR). The modified electrode exhibited an effective catalytic response to the oxidation and reduction of PAR with good reproducibility and stability. The determination was carried out by differential pulse adsorptive stripping voltammetry after a 30 s accumulation time with an open circuit potential and under stirring. The calibration curve is linear in the range from 0.05 to 70 μM of PAR (with a correlation coefficient of 0.9990), and the sensitivity is 1.51 μA·μM^-1. The modified electrode was used to detect PAR in commercial tablets.