Comparison of denuder and impinger sampling for determination of gaseous toluene diisocyanate (TDI)

An air-sampling method employing denuders coated inside with a chemisorptive stationary phase has been evaluated for analysis of the hazardous gaseous 2,4 and 2,6 isomers of toluene diisocyanate (TDI). The denuder stationary phase consisted of polydimethylsiloxane (SE-30) to which dibutylamine (DBA) was added as a reagent for derivatization of TDI. The accuracy and precision of sampling by means of denuders were shown to differ only slightly from those of the established impinger method. The denuder method was, however, also shown to be suitable for long-term measurements (up to 8 h). The limit of determination (LOD) of the method, including LC-APCI-MS-MS analysis, was found to be 1.9 microg m(-3) and 1.2 microg m(-3) for 2,4- and 2,6-TDI, respectively, for short-term measurements (15 min). Significant lower LOD was obtained for long-term measurements. This is well below the Occupational Safety and Health Administration (OSHA) 8-h TWA (time-weighted average) exposure limit, which is 40 microg m(-3) for the sum of the TDI isomers. The denuder method was also found to be robust and easy to handle. The samplers can be prepared several days before sampling with no loss in performance. The contents of denuders should, on the other hand, be extracted immediately after sampling to prevent degradation of the isocyanate derivatives formed.     

The influence of hard‐segments on two‐phase structure and shape memory properties of PCL‐based segmented polyurethanes

Poly(ε‐caprolactone)‐based segmented polyurethanes (PCLUs) were prepared from poly(ε‐caprolactone) diol, diisocyanates (DI), and 1,4‐butanediol. The DIs used were 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluenediisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HDI). Differential scanning calorimetry, small‐angle X‐ray scattering, and dynamic mechanical analysis were employed to characterize the two‐phase structures of all PCLUs. It was found that HDI‐ and MDI‐based PCLUs had higher degree of microphase separation than did IPDI‐ and TDI‐based PCLUs, which was primarily due to the crystallization of HDI‐ and MDI‐based hard‐segments. As a result, the HDI‐based PCLU exhibited the highest recovery force up to 6 MPa and slowest stress relaxation with increasing temperature. Besides, it was found that the partial damage in hard‐segment domains during the sample deformation was responsible for the incomplete shape‐recovery of PCLUs after the first deformation, but the damage did not develop during the subsequent deformation. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 557–570, 2007     

Investigation of a cylindrical chemosorptive denuder for sampling and phase separation of toluene diisocyanate aerosols

A cylindrical chemosorptive denuder in series with a glass fibre filter has been evaluated for sampling toluene diisocyanate (TDI) aerosols. The sampler is designed for measuring personal exposure to diisocyanates. Several denuder coatings and derivatising reagents were investigated. Dimethylpolysiloxane (SE-30) and 5% phenyl dimethylpolysiloxane (SE-54) with either dibutylamine (DBA) or dipentylamine (DPeA) as derivatising reagents yielded the lowest vapour breakthrough (the amount (%) of the vapour that passes through the denuder), close to values predicted by theory. Immobilisation of the SE-30 denuder coating by in-situ cross-linking yielded comparable results. With an SE-30/DBA-coated denuder operating within an airflow range of 100–500 mL min^–1, the phase separation was shown to be consistent with theoretical predictions derived by use of the Gormley–Kennedy equation. This provides a means of calculating the vapour breakthrough and correcting experimentally obtained values with regard to vapour–particulate phase distribution, suggesting that the denuder can provide accurate phase-distribution measurements. The SE-30/DBA denuder can be used over a concentration range spanning nearly six orders of magnitude. Its capacity is sufficient to perform 15-min exposure measurements of a TDI aerosol with air concentrations as high as 1,700 g m^–3, 40 times higher than the Swedish occupational exposure limit (OEL). At the other end of the range, the estimated limit of detection (LOD) was less than 2 ng m^–3 for both the vapour and the aerosol phases when LC–ESI–MS–MS was used for chemical analysis.Electronic Supplementary Material Supplementary material for this article is available at     

Functionalization of graphene oxide with different diisocyanates and their use as a reinforcement in waterborne polyurethane composites

Abstract

To examine the reinforcing effects of isocyanated graphene oxide (NCO-GO) on a waterborne polyurethane matrix, the surface of GO was respectively modified by isophorone diisocyanate (IPDI), hexamethylene diisocyanate (HDI) and toluene diisocyanates (TDI) and then confirmed by FT-IR, Raman, TGA, XRD, TEM, AFM and SEM-EDS. The dispersity behavior between different NCO-GO and polymer was evaluated by FESEM and XRD. The nanocomposites’ chemical structure, emulsion morphology, hydrophobicity, thermal and mechanical properties were investigated by FT-IR, TEM, TGA, tensile testing machine and water contact angle test, respectively. It was shown that these properties of nanocomposites including tensile strength, initial thermal degradation and hydrophobicity were increased by the incorporation of NCO-GO, in which, particularly, the tensile stress and initial degradation temperature were respectively increased from 13.32 to 18.80?Mpa and 249 to 288?°C after the addition of TDI-GO. These superior reinforcing effects were attributed to the two-dimensional structure of NCO-GO as well as the good interfacial adhesion between the NCO-GO and WPU matrix.     

Synthesis and characterization of polyurethanes containing cholesterol and phosphatidylcholine analogous moieties

Several new polyurethanes containing cholesterol and phosphatidylcholine analogous moieties were synthesized by addition polymerization of 2-[bis(2-hydroxyethyl)methylammonio]ethyl 5-cholesten-3β-yl phosphate ( 2 ) with diisocyanates such as hexamethylene diisocyanate (HDI), 2,4-tolylene diisocyanate (TDI), 4,4′-methylenediphenyl diisocyanate (MDI) and m-xylylene diisocyanate (XDI), respectively. They were characterized by their IR and ¹H NMR spectral data and elemental analyses. Preliminary studies suggest that these polyurethanes show the viscosity behavior of common polyelectrolytes.     

Determination of gaseous toluene diisocyanate by use of solid-phase microextraction with on-fibre derivatisation

An SPME method was developed for sampling gaseous 2,4-toluene diisocyanate (2,4-TDI) involving derivatisation of the isocyanate by reacting with dibutylamine (DBA). The TDI-DBA derivative thus formed was determined by LC-MS-MS utilising atmospheric pressure chemical ionisation (APCI). As a first step, DBA was loaded onto a poly(dimethylsiloxane)/divinylbenzene (PDMS-DVB) fibre coating by direct vapour-phase extraction of a highly concentrated diethyl ether solution of DBA. The DBA-loaded fibre was then exposed to an artificially generated atmosphere of gaseous 2,4-TDI. The linearity of the method ranged from 52.8 to 3100 microg m(-3) (6.8 to 400 ppbv) with a sampling time of 60 min. The proposed method has been applied to 2,4-TDI determination in an artificially generated dynamic standard atmosphere, yielding an approximate method detection limit (MDL) of 2 microg m(-3) (0.25 ppbv). This concentration is one twentieth of the Occupational Safety and Health Administration (OSHA) 8-hour time-weighted average (TWA) exposure limit. The sampler with the PDMS-DVB-DBA coating was found to be stable and retains the required amount of DBA for at least 10 days, an important feature for sampling systems with potential in-situ applications.     

Determination of airborne isocyanates as di-n-butylamine derivatives using liquid chromatography and tandem mass spectrometry

A method for the determination of isocyanates as di-n-butyl amine (DBA) derivatives using tandem mass spectrometry (MS/MS) and electrospray ionisation (ESI) is presented. Multiple-reaction monitoring (MRM) of the protonated molecular ions and corresponding deuterium-labelled d₉-DBA derivatives resulted in selective quantifications with correlation coefficients >0.998 for the DBA derivatives of isocyanic acid (ICA), methyl isocyanate (MIC), ethyl isocyanate (EIC), propyl isocyanate (PIC), phenyl isocyanate (PhI), 1,6-hexamethylene diisocyanate (HDI), 2,4-, 2,6-toluene diisocyanate (TDI), isophorone diisocyanate (IPDI), 4,4′-methylenediphenyl diisocyanate (MDI), 3-ring MDI, 4-ring MDI, HDI-isocyanurate, HDI-diisocyanurate, HDI-biuret and HDI-dibiuret. The instrumental precision for 10 repeated injections of a solution containing 0.1 μg ml⁻¹ of the studied derivatives was <2%. Performing MRM of the product ion [DBA + H]⁺ (m/z = 130) from the protonated molecular ion resulted in the lowest detection limits, down to 10 amol (for TDI). Quantification of concentrations below 10⁻⁶ of the occupational exposure limit (OEL) for TDI during 10 min of air sampling was made possible. In an effort to control the formation of alkali adducts, addition of lithium acetate to the mobile phase and monitoring of lithium adducts was evaluated. Having lithium present in the mobile phase resulted in complete domination of [M + Li]⁺ adducts, but detection limits for the studied compounds were not improved. Different deuterium-labelled derivatives as internal standards were evaluated. (1) DBA derivatives of deuterium-labelled isocyanates (d₄-HDI, d₃-2,4-TDI, d₃-2,6-TDI and d₂-MDI), (2) d₉-DBA derivatives of the corresponding isocyanates and (3) d₁₈-DBA derivatives of the corresponding isocyanates. An increase in number of deuterium in the molecule of the internal standard resulted in an increase in instrumental precision and a decrease in correlation within calibration series.     

Polyurethane cationomers. I. Structure-property relationships

Polyether polyurethane cationomers are prepared using poly (tetramethylene oxide) of molecular weight 2000 as soft segments, N-methyl-diethanolamine as chain extender, glycolic acid as quaternization agent, methyl ethyl ketone as solvent, and three different diisocyanates. The three diisocyanates are 4,4′-diphenylenemethylene diisocyanate (MDI), hexamethylene diisocyanate (HDI), and toluene diisocyanate (TDI). Properties of the films cast from solutions of the three series of ionomers are studied by infrared spectroscopy, dynamic mechanical analysis, thermogravimetric analysis, differential scanning calorimetry, wide angle x-ray diffraction, and tensile elongation testing. In the un-ionized and ionized systems, the hard segments exhibit disordered and ordered arrangements, respectively. Ionization disrupts the order and produces increased cohesion in the hard domains, which have opposing effects on the tensile elongation properties. In the MDI and TDI systems, cohesion is predominant, leading to an increased tensile strength and modulus and decreased elongation at break. But in the HDI system, the disruption of the order is predominant, leading to decreased tensile strength and only insignificant reduction in the elongation at break. In the TDI system, the tensile strength is rather low, which is attributed to the poor order in the hard domains resulting from the high content of the asymmetric 2,4-isomer of the urethane.     

Aqueous Dispersion of Polyurethane Anionomer from Aliphatic Diisocyanates and Poly(Hexamethylene Carbonate) Diol

Abstract

Water dispersible polyurethanes (PUs) were prepared from poly(hexamethylene carbonate) (PHC) diol, isophorone diisocyanates (IPDI), hexamethylene diisocyanate (HDI), and dimethylolpropionic acid (DMPA) as latent anionic sites. After neutralization of the carboxyl group from the DMPA unit with triethylamine (TEA), the PU anionomers were dispersed by adding water, following by crosslinking using triethylenetetramine (TETA). The particle size of the dispersion decreased with the content of DMPA and increased with HDI in the HDI-IPDI system, and it exhibited a minimum when the number-average molecular weight (M _n) of the prepolymer was 3000 and 4500, respectively. PUs with a higher content of hard segments from DMPA or TETA, or with a higher content of IPDI rather than HDI, had higher tensile moduli and storage moduli at room temperature. Ultimate tensile properties increased with an increase of the prepolymer molecular weight and the DMPA and HDI content.     

Synthesis of comb-like polyurethanes containing hydrophilic phosphatidylcholine analogues in the main chains and hydrophobic long chain alkyl groups in the side chains

Three new amphiphilic phospholipid diols containing hydrophilic phosphatidylcholine analogues in the main chains and hydrophobic octadecyl, hexadecyl or dodecyl alkyl groups in the side chains were synthesized. The typical phospholipid diol based on an octadecyl group was further reacted with diisocyanates such as hexamethylene diisocyanate (HDI), 2,4-tolylene diisocyanate (TDI) and 4,4′-methylenediphenyl diisocyanate (MDI), respectively. Preliminary studies suggest that polyurethane based on MDI shows a viscosity behavior similar to common polyelectrolytes and exhibits a therm decomposition peak at 244°C due to the phospholipid moiety and a melting point at 218°C.     

Toughening polylactide by dynamic vulcanization with castor oil and different types of diisocyanates

Dynamic vulcanization of polylactide (PLA) with castor oil (CO) and three different diisocyanates, namely 4,4′-diphenylmethane diisocyanate (MDI), hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI), was performed to study the effect of diisocyanate type on the vulcanization process and on the morphology as well as mechanical properties of the PLA/CO-based polyurethane blends. The reactivity of the three diisocyanate followed the order of MDI > HDI > IPDI when reacting with castor oil. Interfacial compatibilization between PLA and the CO-based polyurethane occurred when the less reactive HDI and IPDI was used. Among all the blends, PLA/CO-IPDI showed the finest morphology and the best toughening efficiency. Incorporation of 20 wt% CO-IPDI increased the elongation at break and notched impact strength of PLA by 47.3 and 6.6 times, respectively. Cavitation induced matrix plastic deformation was observed as the toughening mechanism for the PLA blends with CO-based polyurethane. The effect of CO-IPDI content on the morphology and mechanical properties of PLA was studied in detail. The particle size of dispersed CO-IPDI and the elongation at break increased gradually, the tensile strength and Young's modulus decreased gradually, while the impact strength first increased and then decreased with increasing CO-IPDI content from 5 to 30 wt%. The maximum impact strength appeared for the blends with 20 wt% CO-IPDI.     

Investigation of the competitive rate of derivatization of several secondary amines with phenylisocyanate (PHI), hexamethylene-1,6-diisocyanate (HDI), 4,4'-methylenebis(phenyl isocyanate) (MDI) and toluene diisocyanate (TDI) in liquid medium

The stabilization of the isocyanate (NCO) groups during workplace sampling is necessary for their subsequent laboratory analysis. Most derivatization reagents are secondary amines. By carrying out a test in which two secondary amines are added to an isocyanate, the relative rates of these reactions can be evaluated. This evaluation is known for a monoisocyanate, phenylisocyanate (PHI), but is being developed for diisocyanates. This study deals with the relative reactivity (RR) of four diisocyanates: hexamethylene 1,6-diisocyanate (HDI), 4,4'-methylenebis(phenyl isocyanate) (MDI), and the ortho and para isomers of toluene diisocyanate (TDI) in addition to PHI, with four secondary amines: 1-(2-methoxyphenyl)piperazine (MOPIP), 9-(N-methylaminomethyl)anthracene (MAMA), 1-(9-anthracenylmethyl)piperazine (MAP), and dibutylamine (DBA). These competitive derivatization reactions are studied in three reaction solvents, namely acetonitrile, toluene, and acetonitrile doped with water (1% v/v). The results show that the order of reactivity, which doesn't change with the isocyanate as well as with the solvent used, is the following: DBA > MAP > MOPIP > MAMA. The relative difference in reactivity is a function of both the isocyanate and the solvent used. Hindered aromatic diisocyanates (TDI and MDI) show a greater difference in reactivity with the derivatization agents. These differences in reactivity are also modified by the solvent used. For example, larger differences are observed in acetonitrile than in toluene, but the introduction of water to acetonitrile, which does not affect the reaction yield, makes these differences smaller.     

Diisocyanate route as a convenient method for the preparation of novel optically active poly(amide-imide)s based on N-trimellitylimido-S-valine

A new class of optically active poly(amide-imide)s based on an α-amino acid was synthesized via direct polycondensation reaction of different diisocyanates with a chiral diacid monomer. The step-growth polymerization reactions of N-trimellitylimido-S-valine (TISV) (1) with 4,4′-methylene-bis(4-phenylisocyanate) (MDI) (2) was performed under microwave irradiation, as well as solution polymerization under graduate heating and reflux conditions. The optimized polymerization conditions for each method were performed with tolylene-2,4-diisocyanate (TDI) (3), hexamethylene diisocyanate (HDI) (4), and isophorone diisocyanate (IPDI) (5) to produce optically active poly(amide-imide)s via diisocyanate route. The resulting polymers have inherent viscosities in the range of 0.02-1.10 dL/g. Decomposition temperatures for 5% weight loss (T₅) occurred above 300 °C (by TGA) in nitrogen atmospheres. These polymers are optically active, thermally stable and soluble in amide-type solvents. Some structural characterization and physical properties of this new optically active poly(amide-imide)s are reported.     

Tailor-made crosslinkers for high performance PUR coatings – hyperbranched polyisocyanates

The introduction of S elf- C rosslinking I socyanates ( SCI ) as AB₂-building blocks makes it possible to synthesize hydroxyl- or isocyanate-group terminated dendrimers. Furthermore, inherent reactivity differences of non equivalent NCO-groups of specific diisocyanates (such as isophorone diisocyanate [IPDI] or toluylene diisocyanate [TDI]) can be used to build up hyperbranched polyurethane structures in a one pot synthesis without the need of arduous protection/deprotection steps. This synthetic approach allows the construction of tailor-made hyperbranched molecular architectures which are end-functionalized with either hydroxyl or isocyanate groups. These products were then tested as crosslinkers in 2-component coating formulations where they displayed better hardness than any other aliphatic isocyanate raw material.     

UV-curable poly(ethylene glycol)–based polyurethane acrylate hydrogel

Poly(ethylene glycol) (PEG) with molecular weight (M_n) of 1000, 2000, 3000, and 4000 g/mol, four types of diisocyanate [hexamethylene diisocyanate (HDI), 4,4′-dicyclohexylmethane diisocyanate (H₁₂MDI), isophorone diisocyanate (IPDI), and toluene diisocyanate (TDI)], two types of comonomers [acrylamide (AAm) and acrylic acid (AAc)] that comprised up to 60% of the total solid were used to prepare UV-curable PEG–based polyurethane (PU) acrylate hydrogel. The gels were evaluated in terms of mechanical properties, water content as a function of immersion time and pH, and X-ray diffraction profiles of dry and swollen films. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2703–2709, 1999     

Poly(amide-imide)-Silica Gel Hybrids: Synthesis and Characterization

Several poly(amide-imide)-silica gel hybrids containing metal salts were prepared by the sol-gel reaction. Poly(amide-imide)s were prepared by low temperature polycondensation reaction of trimellitic anhydride (TMA) and diisocyanates [isophorone diisocyanate (IPDI), toluene diisocyanate (TDI), hexamethylene diisocyanate (HDI), and 4,4′-methylenebis(phenyl isocyanate) (MDI). The inherent viscosities of the poly(amide-imide)s obtained ranged from 0.39–0.69 dL/g in DMAc. The hydrolysis and condensation reaction of tetramethoxysilane (TMOS) to form a silica gel network was affected in DMAc containing 5% LiCl, CaCl₂ or ZnCl₂ during the formation of poly(amide-imide)s. Films could be cast from DMAc solution and gradual evaporation of the solvent afforded pale yellow to amber colored hybrids in which the salts were dispersed at the molecular level. About 30–60% polymer was incorporated in the hybrids. Pyrolysis of the polymer silica gel hybrid samples at 600°C resulted in the formation of porous silica. Pore size and surface area studies on representative porous silica gels, SiG–4, SiG–5, and SiG–8, obtained upon the pyrolysis of the corresponding hybrids HPAI-4, HPAI-5 and HPAI-8, indicated that the silica gels were mesoporous in nature and had narrow pore size distribution (pore radius = 1.8 nm) with a surface area of 371 m²/g, 335 m²/g and 300 m²/g, respectively. The bottle shaped pores exhibited a pore volume of 0.227 cm³/g, 0.314 cm³/g and 0.280 cm³/g, respectively. Computer simulation modeling studies indicated that the poly(amide-imide) chains were not coiled and there was no agglomeration of the chains.     

用WAXD和SAXS研究新型聚醚－聚酯－聚脲浇铸型弹性体的形态

用ＷＡＸＤ和ＳＡＸＳ研究了一种新型的聚醚－聚酯－聚脲浇铸型弹性体的形态结构．ＷＡＸＤ的结果表明：用三种不同的二异氰酸酯,其硬段中的结晶度依次是ＨＤＩ＞ＭＤＩ＞ＴＤＩ．对于ＨＤＩ和ＭＤＩ混合合成的体系、由于与“Ｐｏｌａｍｉｎｅ”的反应速度不同,形成三相体系．ＳＡＸＳ的结果表明：增加“Ｐｏｌａｍｉｎｅ”分子量,有利于软、硬段的微相分离．对于不同的二异氰酸酯,相分离度依次是ＨＤＩ＞ＭＤＩ＞ＴＤＩ．     

用WAXD和SAXS研究新型聚醚－聚酯－聚脲浇铸型弹性体的形态

 用ＷＡＸＤ和ＳＡＸＳ研究了一种新型的聚醚－聚酯－聚脲浇铸型弹性体的形态结构．ＷＡＸＤ的结果表明：用三种不同的二异氰酸酯,其硬段中的结晶度依次是ＨＤＩ＞ＭＤＩ＞ＴＤＩ．对于ＨＤＩ和ＭＤＩ混合合成的体系、由于与“Ｐｏｌａｍｉｎｅ”的反应速度不同,形成三相体系．ＳＡＸＳ的结果表明：增加“Ｐｏｌａｍｉｎｅ”分子量,有利于软、硬段的微相分离．对于不同的二异氰酸酯,相分离度依次是ＨＤＩ＞ＭＤＩ＞ＴＤＩ．     

Unsaturated poly(ester-imide)s from hydroxy-terminated polybutadiene, dianhydride and diisocyanate

Hydroxy terminated polybutadiene has been used for the first time in the synthesis of poly(ester-imide)s [P(E-I)s]. Anhydride terminated polyester prepolymers were prepared by the reaction of two different polyols--polytetramethyleneoxide glycol (PTMG) of molecular weight 1000 and hydroxy terminated polybutadiene (HTPB) of molecular weight 2500--and different dianhydrides--pyromellitic dianhydride (PMDA), benzophenonetetracarboxylic dianhydride (BTDA) and 4,4^′-(hexafluoroiso-propylidene)diphthalic anhydride (HFDA). The prepolymers were then reacted with different diisocyanates--80:20 mixture of 2,4- and 2,6-tolylene diisocyanate (TDI), 1,6-hexamethylene diisocyanate (HDI), isophorone diisocyanate (IPDI) and 4,4^′-methylene bis(phenylisocyanate) (MDI) resulting in P(E-I)s. The P(E-I)s were characterised by FT-IR, FT-NMR, GPC, TGA, DSC and for static and dynamic mechanical properties. The polymers based on PTMG showed two distinct melting points and behave as thermoplastic elastomers. The thermal stability and mechanical properties of P(E-I)s based on HTPB were substantially higher than those based on PTMG.     

Zur Bestimmung von freien, monomeren Toluylendiisocyanaten und Hexamethylendiisocyanat in Polyurethan(=PUR)-Anstrichstoffen

ZusammenfassungZusammenfassung Es wird über 4 Analysenmethoden zur Bestimmung von kleinen Konzentrationen freier, monomerer Isocyanate [(2,4-,2,6-Toluylendiisocyanat (TDI) und 1,6-Hexamethylendiisocyanat (HDI)] in Polyurethan-Anstrichstoffen berichtet.TDI-Bestimmungen. Colorimetrisch Nach Verseifung der Isocyanate mit Eisessig/Schwefelsäure zu polymeren und monomeren Aminen und Abtrennung der ersteren durch Fällung werden die (monomeren) 2,4,-2,6-Toluylendiamine mit p-Toluyldiazoniumchlorid zu Farbstoffen gekuppelt, deren Extinktionen in einem Photometer bei 470 nm gemessen werden. — Gas-chromatographisch: Die in Benzol gelöste Substanz wird auf einer Säule von 4% Silicongummi SE-30 auf Chromosorb G, AW/DMCS getrennt. Als innerer Standard dient Phenanthren.HDI-Bestimmungen. Dünnschicht-chromatographisch Die Isocyanate werden in benzolischer Lösung mit den aliphatischen Aminogruppen von N-Methyl-N-[4-aminobenzyl]-amin zu Harnstoffen umgesetzt. Nach Trennung an Kieselgel werden die aromatischen Aminogruppen der Derivate diazotiert und mit N-1-Naphthyläthylendiamin zu Azofarbstoffen gekuppelt. Auswertung der HDI-Flecke durch Vergleich mit den Flecken von Standardlösungen. — Destillations-Infrarotspektroskopische Methode: Die Destillation erfolgt nach der ASTM-Methode D 2615-67 T [1]. Im Destillat wird das HDI infrarotspektroskopisch bestimmt: Meßbande 2265 cm^–1.Parallelbestimmungen der TDI- bzw. HDI-Gehalte nach diesen Alternativ-Verfahren ergeben weitgehende Übereinstimmung der Ergebnisse, beim TDI zusätzlich auch mit denen der ASTM-Methode D 2615-67 T.

---

On the determination of free monomeric toluylene diisocyanates and hexamethylene diisocyanate in polyurethane (=PUR) paints

On the Determination of Free Monomerie Toluylene Diisoeyanates and Hexamethylene Diisoeyanate in Polyurethane (= PUR) Paints. Four analytical methods are described for the determination of small concentrations of free monomeric isocyanates [2,4-,2,6-toluylene diisocyanate (TDI), and 1,6-hexamethylene diisocyanate (HDI)] in polyurethane paints.Determination of TDI. Colorimetrically The isocyanates are saponified with glacial acetic acid-sulphuric acid to the polymeric and monomeric amines. The polymeric amines are separated by precipitation and the monomeric amines are coupled with p-toluenediazonium chloride to dyestuffs and their absorbancies are measured by means of a photometer at 470 nm. — GC: The substance is dissolved in benzene and separated on a column of 4% silicone rubber SE-30 on Chromosorb G, AW/DMCS. Phenanthrene is serving as an internal standard.Determination of HDI. TLC The isocyanates are reacted in benzene solution with N-methyl-N-[4-amino-benzyl]-amine to the ureas. After separation on silica gel the aromatic amino-groups of the derivatives are diazotized and coupled with N-[1-naphthyl]-ethylenediamine to the azo dyes. Evaluation of the HDI-spots is performed by comparing with the spots of standard solutions. — Distillation and IR-spectroscopy: The distillation is carried out according to the ASTM-method D 2615-67 T [1]. HDI is determined IR-spectro-scopically in the distillate at 2265 cm^–1.Parallel determinations of the contents of TDI or HDI according to this alternative treatment show a far-reaching agreement of the results. Also the ASTM-method D 2616-67 T is furnishing agreeing results for TDI.

---

---

Für die gewissenhafte Durchführung der Versuche danken wir unseren Mitarbeitern H. Köller, W. Liermann und J. Langohr.