Generation of broadly tunable picosecond mid-infrared laser and sensitive detection of a mid-infrared signal by parametric frequency up-conversion in MgO:LiNbO3 optical parametric amplifiers

Picosecond optical parametric generation and amplification in the near-infrared region within 1.361-1.656 μm and the mid-infrared region within 2.976-4.875 μm is constructed on the basis of bulk MgO：LiNbO 3 crystals pumped at 1.064 μm.The maximum pulse energy reaches 1.3 mJ at 1.464 μm and 0.47 mJ at 3.894 μm,corresponding to a pumpto-idler photon conversion efficiency of 25%.By seeding the hard-to-measure mid-infrared radiation as the idler in the optical parametric amplification and measuring the amplified and frequency up-converted signal in the near-infrared or even visible region,one can measure very week mid-infrared radiation with ordinary detectors,which are insensitive to mid-infrared radiation,with a very high gain.A maximum gain factor of about 7 脳 10 7 is achieved at the mid-infrared wavelength of 3.374 μm and the corresponding energy detection limit is as low as about 390 aJ per pulse.     

Laser-diode-seeded single and double stage femtosecond optical parametric amplification in the mid-infrared

Tunable mid-infrared pulses are generated with a MgO:LiNbO₃-based traveling-wave optical parametric amplifier in single and double stage operation regime pumped by a 1-kHz Ti:sapphire regenerative amplifier system. For the first time to our knowledge a pulsed laser diode is successfully used in the femtosecond regime as a compact seed source at the signal wavelength where the tunability of the generated idler pulses can be realized by tuning the seed wavelength. Almost transform limited mid-infrared pulses as short as 130 and 160 fs with pulse energies as high as 5 and 15 J are produced near 3.5 m by the single and double stage scheme, respectively. The pulse to pulse fluctuations in both cases do not exceed 2% which corresponds to the stability of the pump source.     

Cs^＋-K^＋ Exchange in Z-Cut KTiOPO4 Crystal Covered with Chromium Masking Layer

Cs^＋-K^＋ ion exchanges are performed on z-cut KTiOPO4 crystals with chromium coating covered. The temperature of ion exchange is 430℃, and the time range from 15min to 30min. The dark mode spectra of the samples are measured by the prism coupling method. The channel structures on the samples are observed by a microscope and the near field pattern of the channel waveguides are measured by the end-fire coupling method. The refractive index of the samples increases and the increments at surface are modulated due to the existence of Cr film. In the region covered by Cr film, the refractive index of the samples at the surface increases dramatically in a shallow layer. The results of energy dispersive x-ray spectra indicate that in the region covered with Cr film, Cr ions participate in the ion exchange process, and enhance the refractive index. The results may provide a possibility that achieves index enhancement and Cr doping synchronically.     

Preparation and Luminescence Characteristics of Ca3Y2（BO3）4：Eu^3＋ Phosphor

Ca3Y2 （BO3）4：Eu^3＋ phosphor is synthesized by high temperature solid-state reaction method, and the Iuminescence characteristics are investigated. The emission spectrum exhibits two strong red emissions at 613 and 621 nm corresponding to the electric dipole ^5 Do- ^7F2 transition of Eu^3＋ under 365 nm excitation, the reason is that Eu^3＋ substituting for Y^3＋ occupies the non-centrosymmetric position in the crystal structure of Ca3 Y2 （BO3）4. The excitation spectrum for 613 nm indicates that the phosphor can be effectively excited by ultraviolet （UV） （254 nm, 365nm and 400nm） and blue （470nm） light. The effect of Eu^3＋ concentration on the emission intensity of Ca3 Y2 （BO3）4 ：Eu^3＋ phosphor is measured, the result shows that the emission intensities increase with increasing Eu^3＋ concentration, then decrease. The CIE colour coordinates of Ca3Y2 （BO3）4：Eu^3＋ phosphor is （0.639, 0.357） at 15mol% Eu^3＋.     

KBe2BO3F2飞秒光参量放大中的群速匹配

提出了KBe₂BO₃F₂ （KBBF）飞秒光参量放大中三波群速完全匹配的方法.对于Ⅰ类相位匹配方式采用非共线结构及倾斜抽运光脉冲波面,对于Ⅱ类相位匹配方式采用共线结构同时倾斜抽运光和信号光脉冲波面,可实现参量带宽最大时三波群速的完全匹配,从而获得更高增益,更窄脉宽的参量光. 关键词： 群速匹配 相位匹配 脉冲波面倾斜 飞秒光参量放大     

Laser irradiation of SrTiO3 single crystals

Excimer laser irradiation (248 nm, 34 ns) of SrTiO₃(100)single crystals was studied in order to resolve the feasibility of obtaining well-defined patterned structures. Spots irradiated with a single pulse in the 0.4-1 J/cm² fluence range presented a pattern of cracks along crystallographic directions, which do not propagate beyond the borders, and no ejected material was observed on the non- irradiated areas. Arrays were patterned by translating the single crystal, and different morphologies were found depending on the width of the tracks. Tracks 10 7m wide or more developed a pattern of cracks, whereas 3 7m wide tracks did not. Artificial arrays in magnetoresistive La_2/3Sr_1/3MnO₃ thin films were prepared by using SrTiO₃(100) single-crystal substrates in which arrays had been previously patterned. The interfaces originated a substantial low-field tunnel magnetoresistance.     

Evaluation of Optical Properties of Self-Frequency-Doubling Crystal Yb：GdYAl3（BO3）4 for Laser Applications

Yb：GdYAl3 （B03）4 （Yb：GdYAB） is investigated as a new laser crystal for potential applications in self-frequency doubling. The emission and absorption properties of Yb：GdYAB crystal are studied, and the emission decay times of the upper laser level are measured. The emission cross sections are evaluated using the absorption cross section and principle of reciprocity. The other laser performance parameters, such as the minimum inversion fraction βmin, pump saturation intensity Isat and minimum pump intensity 1rain, are also calculated. The results are discussed in the framework of requirements for an effective diode-pumped Yb^3＋ laser system. Yb：GdYAB is expected to exhibit the most useful laser properties and to be superior to Yb：YAB crystal that has been excellent self-frequency-doubling crystal at present in many key spectroscopic parameter values.     

Ti:Sapphire-pumped femtosecond optical parametric oscillators based on KTiOPO4 and RTiOAsO4

The design, configuration and operation of Ti:Sapphire-laser-pumped femtosecond Optical Parametric Oscillators (OPOs) using KTP and RTA are described. The results presented include configurations capable of producing transform-limited pulses shorter than 40 fs and operating with pump powers as low as 50 mW. Tunability within the 1–3 µn spectral region is demonstrated using pump-tuning alone.     

Generation of broadly tunable picosecond mid-infrared laser and sensitive detection of a mid-infrared signal by parametric frequency up-conversion in MgO:LiNbO₃ optical parametric amplifiers

Picosecond optical parametric generation and amplification in the near-infrared region within 1.361-1.656 μm and the mid-infrared region within 2.976-4.875 μm is constructed on the basis of bulk MgO:LiNbO 3 crystals pumped at 1.064 μm.The maximum pulse energy reaches 1.3 mJ at 1.464 μm and 0.47 mJ at 3.894 μm,corresponding to a pumpto-idler photon conversion efficiency of 25%.By seeding the hard-to-measure mid-infrared radiation as the idler in the optical parametric amplification and measuring the amplified and frequency up-converted signal in the near-infrared or even visible region,one can measure very week mid-infrared radiation with ordinary detectors,which are insensitive to mid-infrared radiation,with a very high gain.A maximum gain factor of about 7 × 10 7 is achieved at the mid-infrared wavelength of 3.374 μm and the corresponding energy detection limit is as low as about 390 aJ per pulse.     

Narrow-linewidth BaGa4Se7 optical parametric oscillator

The linewidth of the BaGa₄Se₇(BGSe) optical parametric oscillator(OPO) was narrowed for the first time, to the best of our knowledge, by inserting a Fabry–Perot(FP) etalon into an L-shaped cavity. When a 15 mm long BGSe(56.3°, 0°) was pumped by a 1064 nm laser, the peak wavelength was ～3529 nm, and the linewidth was 4.53 nm(3.64 cm^-1) under type I phase matching. After inserting a 350 μm thick FP etalon, the linewidth was decreased to 1.27–2.05 nm. When the tilt ...     

超短中红外参量放大过程的时空走离特性

计算了MgO:LiNbO3晶体中,共线与非共线相位匹配光参量放大产生超短中红外激光脉冲过程中的相位匹配曲线、有效非线性系数以及时间和空间走离情况。结果表明,采用非共线相位匹配方式,可以实现三波间群速度匹配;在抑制了泵浦光与信号光之间的空间走离的同时加大了泵浦光与闲频光之间的空间走离,但这种影响可以忽略;同时非共线角的引入使相位匹配角增大,提高了有效非线性系数。因此,非共线角的引入在不影响空间走离的情况下,有效补偿超短中红外参量放大过程中的时间走离,有利于参量放大转换效率的提高。     

超短中红外参量放大过程的时空走离特性

 计算了MgO:LiNbO₃晶体中，共线与非共线相位匹配光参量放大产生超短中红外激光脉冲过程中的相位匹配曲线、有效非线性系数以及时间和空间走离情况。结果表明，采用非共线相位匹配方式，可以实现三波间群速度匹配；在抑制了泵浦光与信号光之间的空间走离的同时加大了泵浦光与闲频光之间的空间走离，但这种影响可以忽略；同时非共线角的引入使相位匹配角增大，提高了有效非线性系数。因此，非共线角的引入在不影响空间走离的情况下，有效补偿超短中红外参量放大过程中的时间走离，有利于参量放大转换效率的提高。     

High repetition rate mid-infrared generation with singly resonant optical parametric oscillator using multi-grating periodically poled MgO:LiNbO3

A high repetition rate mid-infrared singly resonant optical parametric oscillator (OPO) using MgO-doped multi-grating periodically poled LiNbO₃ (MgO:PPLN) is demonstrated. A 1064 nm Q-switched Nd:YVO₄ laser at 10 kHz repetition rate and pulse width of 17.8 ns was used to pump the OPO. The period of the quasi-phase matched (QPM) grating in the multi-grating MgO:PPLN chip varied from 25.5 to 31.5 μm in steps of 0.5 μm. This corresponds to the generation of a signal beam from 1.37 to 1.64 μm and an idler beam from 3.0 to 4.8 μm, respectively. A maximum signal power of 250 mW and idler power of 140 mW has been obtained with an input pump beam of power 1.92 W, for a grating period of 30.5 μm. A maximum optic-optic conversion efficiency of 20% and 7.4% in the idler has been observed. It has been observed that the output power increases as the period of the grating increases.     

High-power, continuous-wave, mid-infrared optical parametric oscillator based on MgO:sPPLT

We report a stable, high-power, cw, mid-IR optical parametric oscillator using MgO-doped stoichiometric periodically poled LiTaO? (MgO:sPPLT) pumped by a Yb fiber laser at 1064 nm. The singly resonant oscillator (SRO), based on a 30 mm long crystal, is tunable over 430 nm from 3032 to 3462 nm and can generate as much as 5.5 W of mid-IR output power, with >4 W of over 60% of the tuning range and under reduced thermal effects, enabling room temperature operation. Idler power scaling measurements at ~3.3 μm are compared with an MgO-doped periodically poled LiNbO? cw SRO, confirming that MgO:sPPLT is an attractive material for multiwatt mid-IR generation. The idler output at 3299 nm exhibits a peak-to-peak power stability better than 12.8% over 5 h and frequency stability of ~1 GHz, while operating close to room temperature, and has a linewidth of ~0.2 nm, limited by the resolution of the wavemeter. The corresponding signal linewidth at 1570 nm is ~21 MHz.     

Growth and optical properties of Cr~（3＋）-doped CdWO_4 single crystals

A high-quality Cr 3+:CdWO4 single crystal at a size of approximatelyΦ25×80 mm is grown using the Bridgman method with CdO,WO3,and Cr2O3 as raw materials and their molar ratio of 100:100:0.5.The temperature gradient of solid-liquid interface at growth is approximately 50?C/cm and the growth rate is 0.05 mm/h.The X-ray diffraction(XRD),absorption,excitation,and emission spectra of different parts of the as-grown and O2-annealed crystals are investigated.Two strong broad optical absorption bands of about 472 and 708 nm are observed,and they are associated with the transitions 4 A2→ 4 T1 and 4 A2→ 4 T2.The weak 4 T2→ 2 E transition(the R-line)at 632 nm is also observed.The crystal-field parameter Dq and the Racah parameters B and C are estimated to be 1 412.4,776.8,and 3 427.6 cm? 1,respectively,according to the absorption spectra and crystal-splitting theory.A broadband fluorescence at about 1 000 nm due to 4 T2→ 4 A2 transition is produced by exciting the samples at 675 nm.After being annealed in an O2 atmosphere,the crystals become more transparent,while the effective light absorption of Cr 3+ ions is evidently enhanced and the emission intensity is also strengthened due to the reduction of oxygen vacancies in the CdWO4 crystal after annealing.     

Mid-infrared,wide-tunable,continuous-wave Nd:YVO4/PPMgLN intracavity optical parametric oscillator

We obtain a continuous-wave (CW) Nd:YVO₄/PPMgLN intracavity singly resonant optical parametric oscillator (ISRO). The threshold value of the CW-ISRO system is only 2.8 W at 808 nm. When the pump power is 5.5 W, an idle laser output power of 410 mW, and a signal laser output power of 345 mW have been achieved. By changing the grating periods of the domain structure on the PPMgLN wafer, we enable a wide-tunable mid-infrared spectrum of 2.95–4.16 μm and near-infrared spectrum of 1.43–1.66 μm.     

Band structure and optical spectra of RbNH4SO4 crystals

First-principal density functional theory (DFT) calculations of the band structure, density of states and dielectric functions ε(E) of the rubidium ammonium sulfate (RAS) crystal, RbNH₄SO₄, in the orthorhombic phase Pnma have been carried out using the CASTEP code. Valence electron bands of the crystal are flat in k-space, that responds to the relatively great effective mass, m*?5m_e. The top valence band of the crystal has been found to be the most flat, what might be an evidence of a weak chemical bonding of the sulfate complexes (SO₄) in the crystal and therefore for the predisposition to structural instability and phase transitions. The characteristic feature is that two top valence bands are originated almost entirely from p-electrons of oxygen. The bottom part of the conduction band is formed mainly by the hydrogen atoms, the higher parts of this band—by a mixed set of chemical elements and orbital moments. The calculated refractive indices in the range of crystal's transparency agree satisfactorily with the experiment considering that the infrared absorption is not taken into account in calculations.