Synthesis and magnetic properties of CoFe2O4 ferrite nanoparticles

CoFe₂O₄ ferrite nanoparticles were prepared by a modified chemical coprecipitation route. Structural and magnetic properties were systematically investigated. X-ray diffraction results showed that the sample was in single phase with the space group . The results of field-emission scanning electronic microscopy showed that the grains appeared spherical with diameters ranging from 20 to 30 nm. The composition determined by energy-dispersive spectroscopy was stoichiometry of CoFe₂O₄. The Curie temperature in the process of increasing temperature was slightly higher than that in the process of decreasing temperature. This can be understood by the fact that heating changed Co²⁺ ion redistribution in tetrahedral and in octahedral sites. The coercivity of the synthesized CoFe₂O₄ samples was lower than the theoretical values, which could be explained by the mono-domain structure and a transformation from ferrimagnetic to superparamagnetic state.     

Synthesis and magnetic properties of spinel CoFe2O4 nanowire arrays

Spinel CoFe₂O₄ nanowire arrays were synthesized in nanopores of anodic aluminum oxide (AAO) template using aqueous solution of cobalt and iron nitrates as precursor. The precursor was filled into the nanopores by vacuum impregnation. After heat treatment, it transformed to spinel CoFe₂O₄ nanowires. The structure, morphology and magnetic properties of the sample were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). The results indicate that the nanowire arrays are compact. And the individual nanowires have a high aspect ratio, which are about 80 nm in diameter and 10 μm in length. The nanowires are polycrystalline spinel phase. Magnetic measurements indicate that the nanowire arrays are nearly magnetic isotropic. The reason is briefly discussed. Moreover, the temperature dependence of the coercive force of the nanowire arrays was studied.     

Synthesis and magnetic properties of antiferromagnetic Co3O4 nanoparticles

Antiferromagnetic Co₃O₄ nanoparticles with diameter around 30 nm have been synthesized by a solution-based method. The phase identification by the wide-angle X-ray powder diffraction indicates that the Co₃O₄ nanoparticle has a cubic spinel structure with a lattice constant of 0.80843(2) nm. The image of field emission scanning electron microscope shows that the nanoparticles are assembled together to form nanorods. The magnetic properties of Co₃O₄ fine particles have been measured by a superconducting quantum interference device magnetometer. A deviation of the Néel temperature from the bulk is observed, which can be well described by the theory of finite-size scaling. An enhanced coercivity as well as a loop shift are observed in the field-cooled hysteresis loop. The exchange bias field decreases with increasing temperature and diminishes at the Néel temperature. The training effect and the opening of the loop reveal the existence of the spin-glass-like surface spins.     

Magnetic properties of large-area one-dimensional WO2 and MoO2 nanorods

Large-area one-dimensional (1D) monoclinic WO₂ and MoO₂ nanorods in the space group P2₁/c were synthesized by reactive thermal evaporation. The as-synthesized 1D WO₂ and MoO₂ nanorods become soft magnetic materials at 10 K, implying that structural or magnetic transitions occur. There are large differences in saturation magnetization, the coercive field, and remanence between the 1D WO₂ and MoO₂ nanorods, although both 1D nanorods have a similar shape.     

Solid state reaction synthesis of NiFe2O4 nanoparticles

Ni-ferrite (NiFe₂O₄) nanoparticles have been synthesized via a solid state reaction process. Ni and Fe bi-metallic nanoparticles in the form of Ni₃₃Fe₆₇ alloy nanopowder are first synthesized by simultaneous evaporation of the required amounts of pure Ni and Fe metals followed by rapid condensation of the evaporated metal flux into solid state by means of an inert gas, helium, using the process of inert gas condensation (IGC). In order to form the NiFe₂O₄ structure, as-synthesized samples (Ni₃₃Fe₆₇) are annealed for 12 h in ambient conditions at different annealing temperatures. Structural analyses show that NiFe₂O₄ starts to form at around 450 °C and gets progressively well defined with increasing annealing temperatures yielding particle with size ranging between 15 and 50 nm. Besides successfully forming NiFe₂O₄, NiO/Fe₃O₄ core/shell nanoparticles have also been synthesized by adjusting the annealing conditions. Three different structures, Ni₃₃Fe₆₇, NiO/Fe₃O₄, and NiFe₂O₄, obtained in this study are compared with respect to their structural and magnetic properties.     

Exchange bias and vertical shift in CoFe2O4 nanoparticles

Magnetic properties of core–shell cobalt ferrite nanoparticles prepared by co-precipitation route in the range 15–48 nm have been studied. It is shown that the coercivity follows non-monotonic size dependence and exhibits a peak at around 26 nm. Field-cooled magnetization exhibited both horizontal (exchange bias) and vertical shifts. The exchange bias is understood as originating at the interface between a surface region (with structural and spin disorder) and a core ferrimagnetic region. The dependence of the exchange bias and vertical shift on the particle size and cooling field is found to have significant differences. These differences are explained in the light of recent results that suggest that there is a variation of the pinning strength amongst the interface spins and the vertical shift is affected by the more strongly pinned uncompensated spins.     

Synthesis and anomalous magnetic properties of CoCr2O4 nanocrystallites with lattice distortion

Nanocrystalline Cobalt chromite (CoCr₂O₄) ceramic has been synthesized under a mild condition, rather than by a high-temperature sintering (e.g. >1673 K, in general). A shifted hysteresis loop with an exchange-bias field of 35.7 kA/m and a high coercivity of 627.9 kA/m at 4.2 K was achieved under the cooling field of 2.39×10⁶ A/m. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) results reveal that a strong lattice distortion and a large amount of surface defects exist in CoCr₂O₄ nanocrystallites (NCs). The anomalous magnetic properties, such as bias field and large coercivity, are attributed not only to the nanosize effect but also to the lattice distortion and crystal defects.     

Mössbauer studies on the superparamagnetic behavior of CoFe2O4 with a few nanometers

CoFe₂O₄ nanoparticles with a cubic spinel structure are prepared by a high-temperature thermal decomposition method. The average particle sizes are 4.6  and 5.7 nm for CoFe₂O₄ made with two kinds of solvents by TEM. Mössbauer spectra of 4.6 nm particles displayed a superparamagnetic behavior as demonstrated by a single line with zero hyperfine fields, but that of 5.7 nm particles did not at room temperature. It is considered that anisotropy energy was still more superior to thermal energy because of particle size of 5.7 nm CoFe₂O₄. Furthermore, Mössbauer spectra exhibited the typical spectrum shapes of the CoFe₂O₄ at 4.2 K. The spectrum at 4.2 K was fitted using two magnetic components of hyperfine fields _Hhf=540.4,512.6$H_{\mathrm{hf}}=540.4,512.6$ kOe and isomer shifts δ=0.40,0.30$\delta =0.40,0.30$ mm/s for 4.6 nm and _Hhf=542.7,512.8$H_{\mathrm{hf}}=542.7,512.8$ kOe and δ=0.41,0.29$\delta =0.41,0.29$ mm/s for 5.7 nm corresponding to Fe³⁺ ions at site A and site B, respectively.     

Area-selectively sputtering the RuO2 nanorods array

The RuO₂ nanorods array is grown selectively on the SiO₂-patterned sapphire (SA) wafers using reactive sputtering. The area-selectivity is attributed to an early nucleation of RuO₂ and its fast surface coverage on SA (1 0 0) and (0 1 2), in contrast to the sluggish nucleation on glassy SiO₂ in the initial sputtering period. The growth domain is explored by investigating the temperature windows at sputtering power 40, 50, and 60 W. The low-temperature bound is limited by the mobility of precursors on SiO₂ surface, which enables the precursors to depart before aggregating into a large size to smear the non-growth region. The high-temperature bound is set by the horizontal growth which enlarges the rod width and deteriorates its one-dimensional feature. The temperature window shrinks with increasing sputtering power. The X-ray photoelectron spectra indicate the as-sputtered rod surface is ruthenium rich. The X-ray diffraction analysis shows that RuO₂ growth on SA (1 0 0) and (0 1 2) follows the epitaxial relations between RuO₂ and SA crystals.     

Magnetic properties of the novel nanocomposite (Zn0.15Ni0.85Fe2O4)0.15/(SiO2)0.85 at room temperature

The value of the effective magnetic anisotropy constant of the ferrimagnetic nanoparticles Zn_0.15Ni_0.85Fe₂O₄ embedded in a SiO₂ silica matrix, determined through ferromagnetic resonance (FMR), is much higher than the magnetocrystalline anisotropy constant. The higher value of the anisotropy constant is due to the existence of surface anisotropy. However, even if the magnetic anisotropy is high, the ferrimagnetic nanoparticles with a 15% concentration, which are isolated in a SiO₂ matrix, display a superparamagnetic (SPM) behavior at room temperature and at a frequency of the magnetization field equal to 50 Hz. The FMR spectrum of the novel nanocomposite (Zn_0.15Ni_0.85Fe₂O₄)_0.15/(SiO₂)_0.85, recorded at room temperature and a frequency of 9.060 GHz, is observed at a resonance field (B_0r) of 0.2285 T, which is substantially lower than the field corresponding to free electron resonance (ESR) (0.3236 T). Apart from the line corresponding to the resonance of the nanoparticle system, the spectrum also contains an additional weaker line, identified for a resonance field of ∼0.12 T, which is appreciably lower than B_0r. This line was attributed to magnetic ions complex that is in a disordered structure in the layer that has an average thickness of 1.4 nm, this layer being situated on the surface of the Zn_0.15Ni_0.85Fe₂O₄ nanoparticles that have a mean magnetic diameter of 8.9 nm.     

Exchange coupled magnetic nanocomposites of Sm(Co1−xFex)5 / Fe3O4 with core/shell structure

Magnetic nanocomposites of Sm(Co_1−xFe_x)₅/Fe₃O₄ (x≈0.1) with the core/shell type structure were successfully fabricated using a two-step polyol process, where as-prepared SmCo_5(1−x) nanoparticles were used as seeds for the ferrite coating. The core/shell composites are quite stable in air and show a typical hysteric behavior of single component, yielding an enhanced coercivity of 2.2 kOe with a saturated magnetization of 130 emu/g at 5 T. The magnetization data clearly reveal the presence of effective exchange coupling between the hard-magnetic Sm(Co_1−xFe_x)₅ core and soft-magnetic Fe₃O₄ shell, suggestive of a single-phase structure rather than a distinctive two-phase one.     

Static susceptibility and heat capacity studies on V3O7·H2O7 nanobelts

V₃O₇·H₂O nanobelts were prepared by a hydrothermal method at 190 °C using V₂O₅·nH₂O gel and H₂C₂O₄·2H₂O as starting agents. The obtained nanobelts have diameters ranging from 40 to 70 nm with lengths up to several micrometers. Measurements of the static magnetic susceptibility and the specific heat show a discontinuous phase transition at around T=145 K, which separates two regions of paramagnetic behavior.     

Scalable synthesis of Sb(III)Sb(V)O4 nanorods from Sb2O5 powder via solvothermal processing

Scalable Sb(III)Sb(V)O₄ nanorods from Sb₂O₅ powder were prepared using solvothermal route. XRD and HRTEM demonstrate that the nanorods are single-crystal orthorhombic-Sb₂O₄ phase with several micrometers long and 200-300 nm diameter size. XPS result further shows that the antimony cations in the nanorods are composed of three valence and five valence antimony ions. The emission of the nanorods appears around 450 nm wavelength. The formation mechanism of the Sb(III)Sb(V)O₄ nanorods was discussed in detail.     

Fabrication and magnetic properties of Fe3O4 nanowire arrays in different diameters

Fe₃O₄ nanowire arrays with different diameters of D=50, 100, 150 and 200 nm were prepared in anodic aluminum oxide (AAO) templates by an electrodeposition method followed by heat-treating processes. A vibrating sample magnetometer (VSM) and a Quantum Design SQUID MPMS magnetometer were used to investigate the magnetic properties. At room temperature the nanowire arrays change from superparamagnetism to ferromagnetism as the diameter increases from 50 to 200 nm. The zero-field-cooled (ZFC) and field-cooled (FC) magnetization measurements show that the blocking temperature T_B increases with the diameter of nanowire. The ZFC curves of D=50 nm nanowire arrays under different applied fields (H) were measured and a power relationship between T_B and H were found. The temperature dependence of coercivity below T_B was also investigated. Mössbauer spectra and micromagnetic simulation were used to study the micro-magnetic structure of nanowire arrays and the static distribution of magnetic moments of D=200 nm nanowire arrays was investigated. The unique magnetic behaviors were interpreted by the competition of the demagnetization energy of quasi-one-dimensional nanostructures and the magnetocrystalline anisotropy energy of particles in nanowires.     

Surface characterization of the Zn-Ni-Al2O3 nanocomposite coating fabricated under ultrasound condition

Zn-Ni-Al₂O₃ nanocomposite coating, which was fabricated by eletrodeposition technique with the aid of ultrasound, was investigated by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis and X-ray photoelectron spectroscopy (XPS). The results reveal that 7.2 wt.% nano-alumina particles uniformly dispersed in the matrix of the composite coating. The XPS analyses demonstrate that the outermost layer of Zn-Ni-Al₂O₃ coating was composed of nano-alumina and Zn(OH)₂, while the transition layer between the outermost layer and the Zn-Ni matrix consisted of nano-alumina, metallic Zn, ZnO and metallic Ni. In order to investigate the influences of ultrasonic agitation and the incorporation of nano-alumina on the composition and surface structure of Zn-Ni matrix, the comparison studies of Zn-Ni-Al₂O₃ nanocomposite coating with Zn-Ni coatings fabricated with and without ultrasound were conducted. The results indicate that ultrasonic agitation resulted in a decrease of Ni content in the Zn-Ni matrix and an increase of the thickness of surface oxide layer; while the incorporation of nano-α-Al₂O₃ increased the Ni content in the Zn-Ni matrix.     

Structural and magnetic properties of Co1−xZnxFe2O4 nanoparticles by co-precipitation method

Co_1−xZn_xFe₂O₄ nanoparticles were prepared by co-precipitation method with x varying from 0 to 1.0. The powder samples were characterized by X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and Fourier transform infrared spectroscopy (FTIR). The average crystallite sizes of the particles were determined from XRD. X-ray analysis showed that the samples were cubic spinel. The average crystallite size (D_aveXR) of the particles precipitated was found to vary from 6.92 to 12.02 nm decreasing with the increase in zinc substitution. The lattice constant (a_o) increased with the increase in zinc substitution. The specific saturation magnetization (M_S) of the particles was measured at room temperature. The magnetic parameters such as M_S, H_c, and M_r were found to decrease with the increase in zinc substitution. FTIR spectra of the Co_1−xZn_xFe₂O₄ with x varying from 0 to 1.0 in the range 400–4000 cm⁻¹ were reported. The spinel structure and the crystalline water adsorption of Co_1−xZn_xFe₂O₄ nanoparticles were studied by using FTIR.     

Morphology and magnetic properties of Co0.8Fe2.2O4 films prepared by the chemical solution deposition

Co_0.8Fe_2.2O₄ ferrite thin films have been prepared on Si(0 0 1) substrates by the chemical solution deposition. Structural characteristics indicate all films are single phase with spinel structure and the space group and the mean grain size increases from 8 to 30 nm with the increase of annealing temperature. The magnetic properties of Co_0.8Fe_2.2O₄ thin films are highly dependent on annealing temperature. The sample annealed at 800 °C possesses high saturation magnetization, moderate coercivity and squareness ratio, making it a promising application candidate in high-density record and magneto-optical materials.     

Temperature dependence of magnetic properties of NiFe2O4 nanoparticles embeded in SiO2 matrix

Spinel ferrite NiFe₂O₄ nanoparticles (?25 nm) in SiO₂ matrix were prepared by sol–gel method. The phase and average crystallite size of the samples were determined by X-ray diffraction method and the particle size distributions were studied by a transmission electron microscope. Magnetic properties of the samples were investigated with different ferrite particle sizes and at various temperatures down to 10 K. Superparamagnetic properties were observed at room temperature when the particle size is less than 10 nm.In superparamagnetic state, the field dependence of magnetization follows Langevin function which was originally developed for paramagnetism. The effective anisotropy constant K_eff is found to increase significantly with the decrease in particle volume and an order of magnitude higher than that of the bulk samples when the particle size is below 5 nm due to the dominance of surface anisotropy. In case of nanosized systems, the effect of size reduction on the law of approach to saturation has also been studied in detail.     

Growth of high-density Ru- and RuO2-composite nanodots on atomic-layer-deposited Al2O3 film

Growth of Ru- and RuO₂-composite (ROC) nanodots on atomic-layer-deposited Al₂O₃ film has been studied for the first time using ion-beam sputtering followed by post-deposition annealing (PDA). X-ray photoelectron spectroscopy analyses reveal that RuO₂ and Ru co-exist before annealing, and around 10% RuO₂ is reduced to metallic Ru after PDA at 900 °C for 15 s. Scanning electron microscopy measurements show that well-defined spherical ROC nanodots are not formed till the PDA temperature is raised to 900 °C. The mean diameter of the nanodots enlarges with increasing PDA temperature whereas the nanodot density decreases, which is attributed to coalescence process between adjacent nanodots. It is further illustrated that the resulting nanodot size and density are weakly dependent on the annealing time, but are markedly influenced by the decomposition of RuO₂. In this article, the ROC nanodots with a high density of 1.6 × 10¹¹ cm⁻², a mean diameter of 20 nm with a standard deviation of 3.0 nm have been achieved for the PDA at 900 °C for 15 s, which is promising for flash memory application.     

Anomalous ferromagnetic behavior of CuO nanorods synthesized via hydrothermal method

Copper monoxide (CuO) nanorods of 30-40 nm in diameter and 100-200 nm in length were successfully synthesized using a hydrothermal reaction method in the presence of sodium citrate. On the basis of the morphology observation and X-ray diffraction patterns of the samples, a possible growth mechanism of the CuO nanorods was proposed. The magnetic properties of CuO nanorods were studied using a SQUID magnetometer and a vibrating sample magnetometer. It was interesting to note that the as-synthesized CuO nanorods showed an anomalous ferromagnetic behavior. The coercive force (H_c) for the CuO nanorods at and were estimated to be 331.39 and 175.88 Oe, respectively. The anomalous ferromagnetic behavior of the as-synthesized CuO nanorods was discussed in terms of the effect of the peculiar morphology.