Influences of Bi2O3 on microstructure and magnetic properties of MnZn ferrite

MnZn ferrites were prepared by conventional oxide ceramic process. The effects of Bi₂O₃ on microstructure and magnetic properties of MnZn ferrites were investigated by means of characterizing the fracture surface micrograph, composition of grain boundary, magnetic properties and density by scanning electron microscope (SEM), energy dispersive X-ray spectroscope (EDS), B-H analyzer and Archimedes method, respectively. The results indicate that Bi₂O₃ mainly segregates and concentrates in the grain boundary regions, promotes solid-state reaction and grain growth, reduces porosity and enhances density. Optimum addition of Bi₂O₃ increases the permeability and saturation magnetic induction, meanwhile ensures the well frequency stability of permeability.     

Effects of different sintering temperature and Nb2O5 content on structural and magnetic properties of Z-type hexaferrites

Nb-doped Z-type hexaferrites (Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁) with composition of Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁+x Nb₂O₅ (where x=0.0, 0.1, 0.2, 0.4, 0.6, 0.8, 1.2, 1.6 and 2.0 wt%) were prepared by a solid-state reaction method. The effects of different sintering temperature (T_s) and Nb₂O₅ content on the sintering behaviors, phase composing, microstructure, and magnetic properties of the samples were investigated. The results from X-ray diffraction and scanning electron microscopy show that as the amount of Nb₂O₅ additive increases, the major phase changes to Z-phase, Simultaneously, M-phase and a small amount of niobate phase appear. The Nb₂O₅ additive promotes the grain growth as reaction center at lower sintering temperature (1220 °C), but at higher temperature (1260 °C), niobate phase separated out in grain boundaries as secondary phase will restrain abnormal grain growth, so closed pores in grains are not formed. The Nb₂O₅ additive can enhance densification, improve initial permeability of hexaferrites by increasing the grain growth of hexaferrite and the displacement of ions in the sintering process due to the aberration and activation of crystal lattice, which is accompanied by the solubility of Nb⁵⁺ in the hexaferrites. A relative density of 96%, maximum initial permeability (32–33), minimum coercivity (454–455 A/m) and resonance frequency above 400 MHz were obtained for the sample with 0.8 wt% Nb₂O₅ sintered at 1260 °C for 6 h.     

Effects of Ta2O5 addition on the microstructure and temperature dependence of magnetic properties of MnZn ferrites

MnZn ferrites with the chemical formula Mn_0.68Zn_0.25Fe_2.07O₄ have been prepared by the conventional ceramic technique. Toroidal cores were sintered at 1350 °C for 4 h in N₂/O₂ atmosphere with 4% oxygen. Then the influence of Ta₂O₅ addition on the microstructure and temperature dependence of magnetic properties of MnZn ferrites was investigated by characterizing the fracture surface micrograph and measuring the magnetic properties over a temperature ranging from 25 to 120 °C. The results show that, when the Ta₂O₅ concentration is not more than 0.04wt%, the grain size has a slight increase with the increase of Ta₂O₅ concentration, the temperature of secondary maximum peak in the curve of initial permeability versus temperature and the lowest power loss shift to lower temperature. However, excessive Ta₂O₅ concentration (>0.04wt%) results in the exaggerated grain growth and porosity increase, which make the initial permeability and saturation magnetic flux density decrease and the power loss increase at room temperature. Furthermore, the temperature of secondary maximum peak in the curve of initial permeability versus temperature and the lowest power loss shift to about 100 °C.     

Effects of Li2CO3 on the sintering behavior and piezoelectric properties of Bi2O3-excess (Bi0.5Na0.5)0.94Ba0.06TiO3 ceramics

(Bi_0.5Na_0.5)_0.94Ba_0.06TiO₃ ceramics doped with Li₂CO₃ and Bi₂O₃ as sintering aids were manufactured, and their micro structural, dielectric and piezoelectric properties were investigated. All specimens could be well sintered at a low-temperature of 1080 °C. The bulk density of the specimens doped with a small amount of Li₂CO₃ was enhanced. The dielectric and piezoelectric properties of ceramics were investigated with different amounts of Li₂CO₃ substitutions. High electrical properties of d₃₃ = 167 pC/N, k_p = 0.34, P_r = 40 μC/cm² and E_c = 38 kV/cm were obtained from the specimen containing 0.1 mol% of Li₂CO₃ sintered at 1080 °C.     

Fabrication of flower-shaped Bi2O3 superstructure by a facile template-free process

A novel flower-shaped Bi₂O₃ superstructure has been successfully synthesized by calcination of the precursor, which was prepared via a citric acid assisted hydrothermal process. The precursor and Bi₂O₃ were characterized with respect to morphology, crystal structure and elemental chemical state by field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). It was shown that both the precursor and Bi₂O₃ flower-shaped superstructure were constructed of numerous nanosheets while the nanosheets consisted of a great deal of nanoparticles. Furthermore, key factors for the formation of the superstructures have been proposed; a mechanism for the growth of the superstructure has been presented based on the FESEM investigation of different growth stages.     

Preparation, electronic structure, and photocatalytic properties of Bi2O2CO3 nanosheet

Bi₂O₂CO₃ nanosheet with a thickness of less than 20 nm was synthesized via hydrothermal and solvothermal process. The properties of the as-prepared nanosheet were characterized by X-ray diffraction, scanning electron microscopy, and diffuse reflectance spectra. The electronic structure was investigated using first-principle calculations. Application of the as-prepared Bi₂O₂CO₃ nanosheet in photocatalysis was also studied.     

Effect of BiFeO3 addition on Bi2O3–ZnO–Nb2O5 based ceramics

In this paper, low temperature sintering of the Bi₂(Zn_1/3Nb_2/3)₂O₇ (β-BZN) dielectric ceramics was studied with the use of BiFeO₃ as a sintering aid. The effects of BiFeO₃ contents and the sintering temperature on the phase structure, density and dielectric properties were investigated. The results showed that the sintering temperature could be decreased and the dielectric properties could be retained by the addition of BiFeO₃. The structure of BiFeO₃ doped β-BZN was still the monoclinic pyrochlore phase. The sintering temperature of BiFeO₃ doped β-BZN ceramics was reduced from 1000 °C to 920 °C. In the case of 0.15 wt.% BiFeO₃ addition, the β-BZN ceramics sintered at 920 °C exhibited good dielectric properties, which were listed as follows: ε_r = 79 and tan δ = 0.00086 at a frequency of 1 MHz. The obtained properties make this composition to be a good candidate for the LTCC application.     

Synthesis and ion conductivity of (Bi2O3)0.75(Dy2O3)0.25 ceramics with grain sizes from the nano to the micro scale

Using (Bi₂O₃)_0.75(Dy₂O₃)_0.25 nano-powder synthesized by reverse titration co-precipitation method as raw material, dense ceramics were sintered by both Spark Plasma Sintering (SPS) and pressureless sintering. According to the predominance area diagram of Bi-O binary system, the sintering conditions under SPS were optimized. (Bi₂O₃)_0.75(Dy₂O₃)_0.25 ceramics with relative density higher than 95% and an average grain size of 20 nm were sintered in only 10 min up to 500 °C. During the pressureless sintering process, the grain growth behavior of (Bi₂O₃)_0.75(Dy₂O₃)_0.25 followed a parabolic trend, expressed as D² − D₀² = Kt, and the apparent activation energy of grain growth was found to be 284 kJ mol^− 1. Dense (Bi₂O₃)_0.75(Dy₂O₃)_0.25 ceramics with different grain sizes were obtained, and the effect of grain size on ion conductivity was investigated by impedance spectroscopy. It was shown that the total ion conductivity was not affected by the grain size down to 100 nm, however lower conductivity was measured for the sample with the smallest grain size (20 nm). But, although only the δ phase was evidenced by X-ray diffraction for this sample, a closer inspection by Raman spectroscopy revealed traces of α-Bi₂O₃.     

Effects of SnO2 addition on the microstructure and magnetic properties of NiZn ferrites

The microstructure and magnetic properties of SnO₂-doped NiZn ferrites prepared by a solid-state reaction method have been investigated. Due to its low melting point (∼1127 °C), moderate SnO₂ enhanced mass transfer and sintering by forming liquid phase, which accelerated the grain growth. However, excessive SnO₂ producing much of liquid phase retarded mass transfer and sintering, leading to a decrease in grain size. The diffraction intensity of the samples doped with SnO₂ addition was stronger than that of the sample without addition. The lattice constant initially decreased up to a content of 0.10 wt% and showed an increase at higher content up to 0.50 wt%. The initial permeability (μ_i) initially increased up to a content of 0.15 wt% and showed a decrease at higher content up to 0.50 wt%; however, losses (P_L) measured at 50 kHz and 150 mT changed contrarily. Both saturation induction (B_S) and Curie temperature (T_C) decreased gradually with increasing SnO₂. Finally, the sample doped with 0.10–0.15 wt% SnO₂ showed the higher permeability and lower losses.     

TeI4掺杂量对n型Bi2Te3基烧结材料热电性能的影响

采用区熔法结合放电等离子体快速烧结(SPS)技术制备了n型Bi₂Te₃基热电材料.在300—500K的温度范围内测量了各热电性能参数，包括电导率(σ)、塞贝克系数(α)和热导率(κ)，研究了掺杂剂TeI₄的含量(质量百分比分别为0，0.05，0.08，0.10，0.13和0.15wt%)对热电性能的影响.结果表明：试样的载流子浓度(n)随TeI₄含量增加而增大，使电导率增大、塞贝克系数的绝对值先增大而后减小，从而导致品质因子(α²σ)呈先增加后降低的变化趋势；同时，由于异质离子(I^-)以及载流子对声子的散射作用增强，可显著降低其晶格热导率.烧结材料的性能优值(ZT=α²σT/κ)对应于TeI₄含量为0.08wt%有其最大值，约为0.92.此外，烧结材料的抗弯强度增加至80MPa左右，从而可以显著改善材料的可加工性以及元器件的使用可靠性. 关键词： 2Te₃')" href="#">Bi₂Te₃ 放电等离子体快速烧结 热电性能     

Effect of CaO-B2O3-SiO2 glass on the magnetic and dielectric properties of NiCuZn ferrites

NiCuZn ferrites with different contents of CaO-B₂O₃-SiO₂ glasses were synthesized by a conventional ceramic technology and sintered at 1050 °C. It was found that the addition of CaO-B₂O₃-SiO₂ influenced the magnetic and dielectric properties of the ferrites. The saturation magnetization increased at first and reached its maximum with the sample of 2 wt% CaO-B₂O₃-SiO₂, and then decreased. The initial permeability decreased with the content of CaO-B₂O₃-SiO₂ but the cut-off frequency increased. The quality factor decreased first and then increased; the maximum quality factor was obtained in the sample with 3 wt% CaO-B₂O₃-SiO₂. With increasing content of CaO-B₂O₃-SiO₂, the permittivity increased sharply. The possible reasons responsible for these changes are explained.     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

纤维状TiO2/Bi2O3光催化剂的制备及其光催化性能

以C₁₆H₃₆O₄Ti和Bi(NO₃)·5H₂O为原料,以棉花纤维为生物模板,合成了系列纤维状TiO₂/Bi₂O₃光催化剂．采用XRD、SEM、UV-Vis等测试技术对样品的相结构、形貌和吸光性能等进行了表征分析．结果表明,样品中的Bi₂O₃为单斜相和四方相共存的混晶,纤维长度达到毫米级,     

Subsolidus phase relation in the Bi_2O_3–Fe_2O_3–La_2O_3 system

Bismuth-containing semiconductor material is a hot topic in photocatalysts because of its effective absorption under the visible light.In this paper,we expect to explore a new bismuth-based photocatalyst by studying the subsolidus phase relations of the Bi2O3–Fe2O3–La2O3system.The X-ray diffraction data shows that in this ternary system the ternary compound does not exist,while seven binary compounds(including one solid solution series Bi1 xLaxO1.5with 0.167≤x≤0.339)are obtained and eight compatibility triangles are determined.     

Effects of surface-modification with Bi2O3 on the thermal stability and photoinduced charge property of nanocrystalline anatase TiO2 and its enhanced photocatalytic activity

Bi₂O₃ surface-modified TiO₂ nanoparticle has been synthesized by sol-hydrothermal processes, followed by post-treatment with an appropriate amount of bismuth nitrate solution, and also characterized by XRD, Raman, BET, TEM, FT-IR, XPS, UV-vis DRS and SPS techniques. The effects of the surface-modification with Bi₂O₃ on the thermal stability, photoinduced charge separation and photocatalytic activity for degrading rhodamine B (or phenol) under ultraviolet (or visible) irradiation are investigated in detail, along with their relationships and the activity enhancement mechanisms are also suggested. The results show that the modification with Bi₂O₃ can improve the thermal stability of the as-prepared anatase crystallites, consequently enhancing the anatase crystallinity so as to promote the photoinduced charge separation. And the modification with Bi₂O₃ also extends the optical response range. It can be concluded that the activity enhancement of surface-modified TiO₂ is mainly attributed to the increase in the photoinduced charge separation rate and to the extent of the optical response range, compared with un-modified ones. Moreover, the inhibition phase transformation mechanism related to Bi₂O₃ is suggested.     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

Comparison of magnetic properties in LixCoO2 and its decomposition products LiCo2O4 and Co3O4

Thermal stability of cathode material in the charged state is an important aspect for the safety of rechargeable batteries. It is well known that layered Li_xCoO₂ decomposes to a mixture of LiCoO₂ and Co₃O₄ at elevated temperatures. However, not many experimental evidences exist on intermediate phases those may form during the decomposition. Using magnetic measurements we show that it is possible to distinguish between the spinels LiCo₂O₄ and Co₃O₄ and thereby follow the decomposition of Li_xCoO₂. We characterize the magnetic behavior of thermally aged Li_xCoO₂ (x = 0.98, 0.76, 0.55) with increasing annealing time. Our results reveal the appearance of magnetic ordering in the thermally degraded products. The detailed analysis illustrates that the formation of Co₃O₄ is preceded by the formation of a meta stable LiCo₂O₄ phase.     

Low temperature fired Ni-Cu-Zn ferrite with Bi4Ti3O12

The Ni-Cu-Zn ferrites with different contents of Bi₄Ti₃O₁₂ ceramics (1-8 wt%) as sintering additives were prepared by the usual ceramic technology and sintered at 900 °C to adapt to the low temperature co-fired ceramic (LTCC) technology. The magnetic and dielectric properties of the ferrite can be effectively improved with the effect of an appropriate amount of Bi₄Ti₃O₁₂. For all samples, the ferrite sintered with 2 wt% Bi₄Ti₃O₁₂ has relatively high density (98.8%) and permeability, while the ferrite with 8 wt% Bi₄Ti₃O₁₂ has relatively good dielectric properties in a wide frequency range. The influences of Bi₄Ti₃O₁₂ addition on microstructure, magnetic and dielectric properties of the ferrite have been discussed.     

机械合金化过程对硫化铋块体热电性能的影响机理

以机械合金化法(MA)结合放电等离子烧结技术(SPS)制备了Bi₂S₃多晶块体热电材料. 研究了MA过程中干磨转速、湿磨时间和湿磨介质对Bi₂S₃多晶热电材料电传输性能的影响. 分析了样品的物相, 观察了显微组织, 测试了电传输性能和热传输性能. 研究表明, 以无水乙醇为湿磨介质时, 随着湿磨时间的延长, 出现了微量Bi₂O₃第二相, 样品的晶粒尺寸减小, 电阻率大幅增加, 功率因子下降. 以丙酮为湿磨介质时, 虽然不存在微氧化反应, 但是由于样品中存在大量孔洞, 导致功率因子降低. 425 r/min 干磨15 h后未湿磨的样品在573 K取得最大的ZT值0.25, 是目前文献报道的最高值.     

Glass additive influence on the sintering behavior, microstructure and microwave magnetic properties of Cu-Bi-Zn co-doped Co2Z ferrites

The Bi₂O₃-B₂O₃-ZnO-SiO₂ (BB35SZ) glass effects on the sintering behavior and microwave magnetic properties of Cu-Bi-Zn co-doped Co₂Z ferrites were investigated to develop low-temperature-fired ferrites. The glass wetting characteristics on the Co₂Z ferrite surface, X-ray diffractometer, scanning electron microscopy and a dilatometer were used to examine the BB35SZ glass effect on Co₂Z ferrite densification and the chemical reaction between the glass and Co₂Z ferrites. The results indicate that BB35SZ glass can be used as a sintering aid to reduce the densification temperature of Co₂Z ferrites from 1300 to 900 °C. 3(Ba_0.9Bi_0.1O)·2(Co_0.8Cu_0.2O)·12(Fe_1.975Zn_0.025O₃) ferrite with 2 wt% BB35SZ glass can be densified below 900 °C, exhibiting an initial permeability of 3.4. This process provides a promising candidate for multilayer chip magnetic devices for microwave applications.