Comparison of media properties between hard/soft stacked composite and capping layer perpendicular recording media

The effect of soft layer thickness (t_Soft) of CoTaZr–SiO₂ and low Pt-containing CoCrPtO layers on media properties in hard/soft (H/S) stacked media is compared to media properties in conventional capping layer (CL) media. Coercivity and coercivity squareness in H/S stacked media continuously decrease with increasing t_Soft, while they increase in CL media. H/S stacked media with CoTaZr–SiO₂ layers having higher saturation magnetization and in-plane magnetic anisotropy constant exhibit stronger demagnetization effect. Compared to CL media, H/S stacked media with CoCrPtO soft layers improve signal-to-noise ratio and magnetic write width. However, the use of a relatively soft layer deteriorates adjacent track erasure and does not improve media writeability due to compensation effect between softer and harder layers to be used. These phenomena can be understood as undesirable side effects of a soft layer: higher demagnetization field and larger lattice mismatch.     

Transition from reversible to irreversible magnetic exchange-spring processes in antiferromagnetically exchange-coupled hard/soft/hard trilayer structures

The demagnetization processes of antiferromagnetically exchange-coupled hard/soft/hard trilayer structures have been studied based on the discrete one-dimensional atomic chain model and the linear partial domain-wall model. It is found that, when the magnetic anisotropy of soft layer is taken into account, the changes of the soft layer thickness and the interfacial exchange coupling strength may lead a transition of demagnetization process in soft layer from the reversible to the irreversible magnetic exchange-spring process. For the trilayer structures with very thin soft layer, the demagnetization process exhibits typical reversible exchange-spring behavior. However, as the thickness of soft layer is increased, there is a crossover point t_c, after which the process becomes irreversible. Similarly, there is also a critical interfacial exchange coupling constant A_sh^c, above which the exchange-spring process is reversible. When A_sh<A_sh^c, the irreversible exchange-spring process is achieved. The phase diagram of reversible and irreversible exchange-spring processes is mapped in the plane of the interfacial exchange coupling A_sh and soft layer thickness N_s.     

Effect of nanoparticle size on magnetic damping parameter in Co92Zr8 soft magnetic films

Co₉₂Zr₈(50 nm)/Ag(x) soft magnetic films have been prepared on Si (111) substrates by oblique sputtering at 45°. Nanoparticle size of Co₉₂Zr₈ soft magnetic films can be tuned by thickening Ag buffer layer from 9 nm to 96 nm. The static and dynamic magnetic properties show great dependence on Ag buffer layer thickness. The coercivity and effective damping parameter of Co₉₂Zr₈ films increase with thickening Ag buffer layer. The intrinsic and extrinsic parts of damping were extracted from the effective damping parameter. For x=96 nm film, the extrinsic damping parameter is 0.028, which is significantly larger than 0.004 for x=9 nm film. The origin of the enhancement of extrinsic damping can be explained by increased inhomogeneity of anisotropy. Therefore, it is an effective method to tailor magnetic damping parameter of thin magnetic films, which is desirable for high frequency application.     

The growth of soft magnetic FeNiN thin films under different experimental procedures

FeNiN thin films with good soft magnetic properties were synthesized on Si (1 0 0) substrates at 473 K by RF magnetron sputtering. The dependence of phase structure and magnetic properties on nitrogen partial pressure, nickel concentrations, film thickness and substrate temperature were systematically investigated. The phase evolution from α-(Fe,Ni)N to ξ-(Fe,Ni)₂N with increase of nitrogen partial pressure was seen. The addition of Ni caused FeNiN films to turn from BCC structure to FCC structure. Clear reproducible striped domains appeared at the film surfaces when X_Ni=19.6%, which is explained by the high enough perpendicular anisotropy and the small stress in the film. All films show smooth surfaces and good soft magnetic properties compared to corresponding FeN compounds. The magnetic properties depended dramatically on the phase structure. Optimum soft magnetic properties with H_C of <1 Oe are obtained between 5.0%?X_Ni?10.0%.     

Preparation and recording characteristics of granular-type perpendicular magnetic recording media with thin intermediate layer

Granular-type media with thin Ru intermediate layer were prepared on a highly oriented high-B_s FeCo soft underlayer (SUL). A CoPt–TiO₂ recording layer on a Ru intermediate layer of only 2 nm had high-crystal orientation, high H_c of 6.5 kOe, and a high squareness ratio (SQ) of 0.99. The magnetic property of the SUL was also good. The recording performance was measured for the media with different Ru intermediate thicknesses by using a single-pole-type (SPT) head. The media had large reproduced output even for the Ru intermediate layer thickness of 2 nm.     

Analysis of the magnetic losses in iron-based soft magnetic composites with MgO insulation produced by sol-gel method

This work investigated the magnetic losses of heat treated iron-based soft magnetic composites with a thin MgO insulating layer produced by sol-gel method. The samples were characterized by energy dispersive X-ray spectroscopy, X-ray analysis and Fourier transform infrared spectroscopy. The results show that the surface of the powders contains a thin layer of MgO insulation. The loss results indicate that the hysteresis part for both the core loss and total loss factor was approximately the same for the MgO-insulated compacts and conventional SOMALOY^TM samples with phosphate insulation after annealing at 600 °C. But the MgO-insulated compacts exhibited significantly lower eddy current contribution of both core loss and total loss factor with respect to SOMALOY^TM samples after annealing. Also the contribution of eddy current in the iron particles for MgO insulated compacts (k_p=0.91) was noticeably higher than this contribution for SOMALOY^TM samples (k_p=0.18) after annealing due to the higher electrical resistivity of the MgO-insulated compacts.     

Effects of soft layer softness on the magnetic properties of perpendicular exchange-coupled nanocomposite films

The anisotropy of the soft layer in the Co_100−xPt_x/Co₇₁Pt₂₉ (x=0, 7 and 17) perpendicular exchange-coupled composite (ECC) films was varied by changing the Pt content. The effects of soft layer softness (thickness and anisotropy) on the coercivity and magnetization reversal mechanisms of ECC were studied. Results showed that both remanence ratio (M_r/M_s) and coercivity of the ECC films reduced with an increase in soft layer thickness. However, the rate of coercivity reduction reduced when soft layer anisotropy was increased simultaneously. This was confirmed by the following facts. For the ECC with Co soft layer, the magnetization reversal mechanism within the ECC grains changed from coherent rotation to domain wall motion when soft layer thickness was changed from 2 to 15 nm. The impact of soft layer thickness on the magnetization reversals of the ECC grains reduced with an increase in soft layer anisotropy. On the other hand, the change of soft layer easy axis direction could possibly change the reversal mechanism of the ECC grains. The above experimental results showed that the coercivity of ECC film was controlled by the reversal mechanism inside the ECC grains.     

3D and 1D micromagnetic calculation for hard/soft bilayers with in-plane easy axes

Macroscopic hysteresis loops and microscopic magnetic moment distributions have been determined by three-dimensional (3D) as well as one-dimensional (1D) micromagnetic models for exchange-coupled Nd₂Fe₁₄B/α–Fe bilayers and carefully compared with each other. It is found that the results obtained from the two methods are consistent with each other, where the nucleation and coercive fields decrease monotonically as the soft layer thickness L^s increases whilst the largest maximum energy products (roughly 600 kJ/m³) occur at L^s=5 nm. Moreover, the calculated angular distributions in the thickness direction for the magnetic moments are similar. Nevertheless, the calculated critical fields and energy products by 3D OOMMF are systematically smaller than those given by the 1D model, mainly due to the local demagnetization fields, which are taken into account in the 3D calculation and ignored in the 1D calculation. It is demonstrated by the 3D calculation that the large demagnetization fields in the corners of the soft layers reduce the nucleation fields and thus facilitate the magnetic reversal. Such an effect enhances as L^s increases. When L^s=20 nm, the differences between the coercivity is as large as 30%, while the nucleation fields obtained by the two methods have opposite signs.     

Influence of quenching rate on the structural, soft magnetic and magnetoimpedance properties of melt-spun Co69Fe7Si14B10 alloy

Melt-spun ribbons of Co₆₉Fe₇Si₁₄B₁₀ alloy have been prepared at different wheel speeds viz. 47, 34 and 17 m/s and investigated for structural and magnetic properties. Degree of amorphicity in the as-spun ribbons is found to increase with wheel speed. Amorphous phase crystallizes in two stages producing Co₂Si, Co₂B and CoSi phases on annealing. Increase in wheel speed improves soft magnetic and magnetoimpedance properties due to decrease in perpendicular anisotropy which is associated with stripe domain formation. On annealing soft magnetic properties and magnetoimpedance deteriorate due to the formation of crystalline phases.     

Effect of Nb addition on the structure and soft magnetic properties of melt-spun Co69Fe7Si14B10 alloy

Melt-spun ribbons of Co₆₉Fe₇Si_14−xNb_xB₁₀ alloys with x=0, 2 and 4 have been prepared and characterized for structure and soft magnetic properties. Ribbons with x=0 and x=2 are found to be completely amorphous whereas the ribbon with x=4 contains irregular shaped faulted Co₂Si orthorhombic phase with grain size of about 100 nm. Nb addition is found to decrease the degree of amorphicity and induce perpendicular anisotropy, deteriorating the soft magnetic and magnetoimpedance properties.     

Acoustic soft modes of Nb3Sn in high magnetic fields

In single crystal Nb₃Sn the effect of a magnetic field upon the soft sound velocity v_s (110, 1$\text{1}$0) was measured at different temperatures above the structural phase transition point. The observed quadratic variation with field is in accordance with theory. But the magnitude of the field dependence is much smaller than expected and can only be explained by existing theories if the magnetic moment of the electron would vary by as much as a factor of two within an energy interval of some 100 K.     

Resonant soft X-ray scattering studies of multiferroic YMn2O5

We performed soft X-ray resonant scattering at the MnL _2,3- and OK edges of YMn₂O₅. While the resonant intensity at the Mn L _2,3 edges reflects the magnetic order parameter, the resonant scattering at the O K edge is found to be directly related to the macroscopic ferroelectric polarization. The latter observation reveals the important role of the spin-dependent Mn-O hybridization for the multiferroicity of YMn₂O₅. We present details about how to obtain correct energy dependent lineshapes and discuss the origin of the resonant intensity at the O K edge.     

Advanced granular-type perpendicular recording media

We introduce our recent experimental results for three blocked layers for currently used perpendicular recording media; a recording layer (RL: for recording), a soft magnetic underlayer (SUL: magnetic flux path in writing), and a nonmagnetic intermediate layer (NMIL: underlayer of RL and separation layer between RL and SUL). For the NMIL, uniaxial crystallographic symmetry is an essential requirement for suppression of variant growth of magnetic grains in granular-type RL. From this view point, AlN with wurtzite structure and materials with pseudo-hcp structure, which means fcc structure with stacking faults, were found to be effective. For the SUL, disordered hcp CoIr with negative K_u were found to well suppress both spike noise and track erasure due to a wide distribution of magnetic flux under the return yoke in writing and formation of a Neel wall instead of a Bloch wall in the SUL. For the RL, positive-/negative-K_u stacked media with incoherent switching mode was found to be effective in order to solve the recent write-ability problem for high K_u RL material with high thermal stability. Applying all these items, an advanced medium concept with the stacking structure of “CoPtCr-oxide/CoIr-oxide/CoIr/pseudo-hcp nonmagnetic layer/substrate” is very promising from the view point of (1) switching field reduction of a RL with high K_u material, (2) conventional amorphous SUL free, and (3) conventional NMIL free.     

Direct lepton production by soft virtual bremsstrahlung

Internal conversion of soft virtual bremsstrahlung, calculated in an essentially model independent infrared limit, yields numerous low mass-low energy lepton pairs. The resulting single lepton spectra rise sharply towards p_T = 0 for large angles θ_cm and towards x = 0 for θ_cm = 0°. The ratio $\text{e}\text{π}$ for p_T ? 400 MeV/c exhibits roughly the experimentally observed properties.     

Synthetic Co50Pt50/Ru/CoFe hard–soft trilayer in spin valves

The influence of deposition power and seedlayer on the properties of hard magnet Co₅₀Pt₅₀ was studied. Co₅₀Pt₅₀(/Co₉₀Fe₁₀)/Ru/Co₉₀Fe₁₀ trilayer was used as pining/pinned layer in spin valves. The influences of different hard layer, soft layer and free layer on exchange bias, interlayer coupling, and magnetoresistance (MR) ratio were studied. Weak antiferromagnetic interlayer coupling was obtained by adjusting the thickness of hard and soft layers. MR of a spin valve with structure Cr2/CoFe0.5/CoPt4/CoFe0.5/Ru0.8/CoFe2.2/Cu2.05/CoFe2.6/Cu1.1/Ta1 reached 10.68% (unit in nm), which is comparable to those of IrMn-based synthetic spin valves. The increment of the coercivity of the free layer is mainly due to the static magnetic interaction between the hard layer and the free layer.     

Electrochemical formation of intermediate layer for Co/Pd multilayered media

Pd nanocluster seeds were formed on a soft magnetic underlayer (SUL) using an electrochemical substitution reaction, and were utilized as an intermediate layer for a Co/Pd multilayered ([Co/Pd]_n) perpendicular magnetic recording medium. A CoNiFeB film prepared with electroless deposition was used as SUL, which was immersed into a PdCl₂ solution for the formation of Pd seeds. The Pd seeds were found to effectively reduce the size of magnetic domains in the [Co/Pd]_n film deposited on them. The optimization of the concentration of the PdCl₂ solution and the use of the pretreatment process with a SnCl₂ solution were effective to obtain the smooth SUL surface with fine Pd seeds as small as 5 nm. The 20 nm-thick [Co/Pd]_n film deposited on the optimized Pd seeds/CoNiFeB SUL exhibited a high coercivity of 7.8 kOe and a small magnetic domain size of 69 nm. These results indicated that the combination of the Pd seeds and the electroless-deposited SUL was desirable in terms of the improvement not only in the magnetic properties of [Co/Pd]_n media but also in the mass productivity of the underlayer.     

Excellent soft magnetic properties realized in FeCoN thin films

FeCoN soft magnetic thin films are prepared by using the reactive direct-current magnetron sputtering technique. It is found that the addition of N₂ can reduce the coercivity of the FeCoN film, and excellent soft magnetic properties can be obtained when the ratio of N₂ flow to total gas flow is 10%. The influences of texture, grain size, and stress on the magnetic properties and the high-frequency behaviors of the films are also discussed.     

Exchange coupling and remanence enhancement in nanocomposite Nd–Fe–B/FeCo multilayer films

Nd–Fe–B-type hard phase single layer films and nanocomposite Nd₂₈Fe₆₆B₆/Fe₅₀Co₅₀ multilayer films with Mo underlayers and overlayers have been fabricated on Si substrates by rf sputtering. The hysteresis loops of all films indicated simple single loops for fixed Nd–Fe–B layer thickness (10 nm) and different FeCo layer thickness (d_FeCo=1–50 nm). The remanence of these films is found to increase with increasing d_FeCo and the coercivity decrease with increasing d_FeCo. It is shown that high remanence is achieved in the nanocomposite multilayer films consisting of the hard magnetic Nd–Fe–B-type phase and soft magnetic phase FeCo with 20 nm?d_FeCo?3 nm. The sample of maximum energy product is 27 MG Oe for d_FeCo=5 nm at room temperature. The enhancement of the remanence and energy products in nanocomposite multilayer films is attributed to the exchange coupling between the magnetically soft and hard phases.     

Effect of the soft layer thickness on magnetization reversal process of exchange-spring nanomagnet patterns

A systematic study of the magnetization reversal behavior in the regular arrangement of L1₀-FePt based exchange-spring nanomagnets with different thicknesses of the Co soft magnetic layer is presented. The magnetic property of the hard magnet is compared to two tuned exchange-spring magnets: its systems of 20 nm L1₀-FePt/3 nm, and 7 nm Co. In particular, we focus on the switching field distribution. The exchange coupling showed narrower SFD, in spite of the decoupled part switches earlier. The magnetization switching mechanism of exchange-spring nanomagnets patterns has been revealed with a first-order reversal curves technique and the switching field distribution. Further, the microscopic results using magnetic force microscopy show that the spin rotation of the non-interacting part in the thicker soft layered exchange-spring magnet. The part influences the magnetization reversal process. According to the experimental results, exchange coupling strength can be tuned by the thickness of the soft magnetic layer.