Synthesis of small crystal polycrystalline mordenite membrane

Mordenite membrane was prepared on -Al₂O₃ tube by in situ hydrothermal synthesis with tetraethylammonium bromide (TEABr) as template agent. By the application of aging process of the parent solution, the size of mordenite crystals could be remarkably reduced from 20–30 (without aging) to 4–5 μm. The small crystal mordenite membrane had higher performance of pure gas permeation than big crystal mordenite membrane. The ideal selectivity of H₂/N₂ was 9.80, much higher than 3.82 of big crystals mordenite membrane. The membrane displayed high water-permselective performance in pervaporation (PV) test toward water/organic liquid mixtures. The highest separation factors achieved toward water/methanol, water/ethanol, water/n-propanol and water/i-propanol were 2600 (X_W=50%, T=323 K), 5500 (X_W=50%, T=343 K), 6000 (X_W=15%, T=343 K) and 6800 (X_W=50%, T=343 K), respectively.     

Silicalite-filled poly(siloxane imide) membranes for removal of VOCs from water by pervaporation

Silicalite-filled poly(siloxane imide) (PSI) membranes were prepared for the separation of volatile organic compounds (VOCs) from water via pervaporation. PSI copolymer was synthesized by polycondensation of 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) with a siloxane-containing diamine, e.g., poly(dimethylsiloxane), bis(3-aminopropyl) terminated (PSX), added with 3,3-diaminodiphenyl sulfone (DDS). 2,4,6-Triamine pyrimidine (TAP) was added into the casting solution in order to enhance the compatibility between the polymeric matrix and the filler, silicalite. The PSI membranes were characterized by SEM. The surface morphology for the membrane with the addition of TAP differs from that without TAP. The latter seems to be consisting of particles in the membrane surface. The sorption selectivity of the PSI membranes for chloroform/water solutions was investigated, and there was a highest value for it around 50 wt.% of PSX content. The pervaporation performance of the membranes was studied with the separation of chloroform/water mixture. The silicalite-filled membrane with 120 μm thickness exhibit a high total permeation flux of 280 g m⁻² h⁻¹ with separation factor of 52.2 for 1.2 wt.% of the chloroform/water mixture.     

Biosorption of heavy metals on Aspergillus fumigatus immobilized Diaion HP-2MG resin for their atomic absorption spectrometric determinations

A solid phase extraction procedure based on biosorption of copper(II), lead(II), zinc(II), iron(III), nickel(II) and cobalt(II) ions on Aspergillus fumigatus immobilized Diaion HP-2MG has been investigated. The analytical conditions including amounts of A. fumigatus, eluent type, flow rates of sample and eluent solutions were examined. Good recoveries were obtained to the spiked natural waters. The influences of the concomitant ions on the retentions of the analytes were also examined. The detection limits (3sigma, N = 11) were 0.30 μg l⁻¹ for copper, 0.32 μg l⁻¹ for iron, 0.41 μg l⁻¹ for zinc, 0.52 μg l⁻¹ for lead, 0.59 μg l⁻¹ for nickel and 0.72 μg l⁻¹ for cobalt. The relative standard deviations of the procedure were below 7%. The validation of the presented procedure is performed by the analysis of three standard reference materials (NRCC-SLRS 4 Riverine Water, SRM 1515 Apple leaves and GBW 07605 Tea). The procedure was successfully applied for the determination of analyte ions in natural waters microwave digested samples including street dust, tomato paste, black tea, etc.     

Separation of 2-butanol–water mixtures by pervaporation through PVA–NYL 66 blend membranes

Blend membranes of poly(vinyl alcohol) (PVA) and nylon 66 (NYL) were synthesized and crosslinked with glutaraldehyde (GA) and assessed for their suitability in dehydrating 2-butanol by pervaporation (PV). These blends were subjected to sorption studies to determine the extent of interaction and degree of swelling in pure liquids as well as binary mixtures. Wide-angle X-ray diffraction (WAXD) and thermal gravimetric analysis (TGA) were carried out to investigate changes in crystallinity and thermal stability, respectively. The effect of experimental parameters such as feed water concentration, permeate pressure and barrier thickness on membrane flux and selectivity was evaluated. The membranes were found to have good potential for breaking the azeotrope of 27.6 wt.% water with a flux of 3.07 kg/m² h 10 μm and selectivity of 26.5. Selectivity was found to improve with decreasing feed water concentration and increasing membrane thickness, whereas opposite trends were observed in case of flux. Higher permeate pressure caused a reduction in both flux and selectivity. These effects were clearly elucidated.     

Determination of arsenic by pervaporation-flow injection hydride generation and permanganate spectrophotometric detection

A novel pervaporation-flow injection (PFI) system for the determination of As(III) in aqueous samples at μg l⁻¹ level is described. The analytical procedure involved stopping the acceptor stream and injecting acidified As(III) samples into a 0.3 M HCl stream which was mixed with a 0.14 M sodium borohydride in 0.025 M NaOH stream. The arsine generated was transported in the pervaporation unit across a semi-permeable membrane (1.5 mm thickness) into the static acceptor solution containing 1.0×10⁻⁴ M KMnO₄ in 0.1 M H₂SO₄ where it was oxidised. The acceptor stream was restarted after 6.5 min, and the decrease in permanganate absorbance at 528 nm was monitored to determine the initial concentration of As(III) in the samples. The method is characterised by a linear calibration range from 0.25 to 2000 μg l⁻¹, a detection limit of 0.18 μg l⁻¹ and a sampling frequency of 7 h⁻¹. Samples containing As(V) were pre-treated with KI and HCl prior to injection to reduce As(V) to As(III). The effects of common anionic and cationic interferences, and the elimination of some metallic interferences using -cysteine are discussed. The method was applied to the analysis of environmental waters and the results were in good agreement with hydride generation atomic absorption spectrometric data.     

Pervaporation separation of aqueous chlorophenols by a novel polyurethane urea–poly (methyl methacrylate) interpenetrating network membrane

A novel polymer membrane system consisting of interpenetrating network (IPN) of hydroxy terminated polybutadiene (HTPB) based polyurethane urea (PUU)–poly (methyl methacrylate) (PMMA) has been designed and developed as highly permselective membrane for pervaporation separation of toxic p-chlorophenol and 2,4-dichlorophenol from their dilute aqueous solutions. It was observed that 3 ppm 2,4-dichlorophenol in water could be reduced to 0.3 ppm 2,4-dichlorophenol using a PUU–PMMA IPN membrane of 28 cm² area and 150 μm thickness. This membrane has shown high selectivity towards p-chlorophenol and 2,4-dichlorophenol at very low concentration in feed. Feed concentration of p-chlorophenol was varied from 1000 to 7000 ppm and that of 2,4-dichlorophenol was varied from 3 to 4000 ppm. Fifty seven percent 2,4-dichlorophenol in permeate was obtained from 3 ppm concentration in feed compared to 87% 2,4-dichlorophenol in permeate from 1000 ppm in feed. Pervaporation studies were carried out by varying the temperature of feed, membrane thickness and PMMA content in the membrane. The results of this investigation have revealed that these membranes would be suitable for separation of chlorophenols from industrial effluents.     

On-line determination of cyanide in the presence of sulfide by flow injection with pervaporation

A pervaporation-flow injection (PFI) method is described for the analysis of cyanide in the presence of sulfide. The interfering sulfide ion in the injected sample is precipitated on-line using an acidified lead nitrate reagent solution before the donor stream enters the pervaporation cell. Using amperometric detection at a silver electrode set at −50 mV (vs Ag/AgCl), linear calibration was obtained in the range 0.02–100.0 mg l⁻¹ with a detection limit of 1.0 μg l⁻¹. Sample throughput was of the order of 12–15 h⁻¹. When the method was applied to the analysis of synthetic samples, there was no significant interference from sulfide at concentrations up to 50 mg l⁻¹. Thiocyanate did not interfere at levels up to 1000 mg l⁻¹. When applied to industrial samples containing sulfide and thiocyanate ions where the cyanide ions are predominantly complexed with various metal ions the PFI method was found to give results close to those obtained by standard distillation methods for weak acid dissociable (WAD) cyanide.     

Uranium determination at ppb levels by X-ray fluorescence after its preconcentration on polyurethane foam

A sensitive method based on the preconcentration of uranium on powdered polyurethane foam (PUF) has been developed to determinate this element in water samples by X-ray florescence. Uranium at ppb levels was sorbed as the salicylate complex on powdered PUF at pH 4.0. The resulting PUF was filtered through a filter paper and used for X-ray fluorescence measurements. For 50 μg/l of uranium the coefficient of variation for five measurements is 5% and the detection limit is 5.5 μg/l. The interference level of various ions and ligands was studied and optimum conditions were developed to determine uranium in reference materials, waste water, mine drainage, and sea water.     

Pervaporation performance of crosslinked polyethylene glycol membranes for deep desulfurization of FCC gasoline

An crosslinked polyethylene glycol (PEG) membrane was prepared for fluid catalytic cracking (FCC) gasoline desulfurization. Sulfur enrichment factor come to 4.75 and 3.51 for typical FCC gasoline feed with sulfur content of 238.28 and 1227.24 μg/g, respectively. Pervaporation performance of membranes kept stable within the long time run of 500 h, which indicated that crosslinked PEG membranes had the property of resisting pollution. Judging from chromatographic analysis, the membranes were more efficient for thiophene species. Effects of operation conditions including permeate pressure, feed temperature, feed flow rate and feed sulfur content level on the pervaporation performance were investigated. Permeation flux decreased with increasing permeate pressure while increased with the operating temperature increase. Sulfur enrichment factor increased firstly and decreased then when permeate pressure and temperature rose. The peak value occurred at 10.5 mm Hg and 358 K for model compounds feed (378 K for FCC gasoline feed). Arrhenius relationship existed between flux and operating temperature. Both sulfur enrichment factor and flux were shown to increase with increasing feed flow rate. Permeation flux increased while sulfur enrichment factor decreased as the feed sulfur content increased, but the influence of increasing sulfur content on pervaporation performance weakened when sulfur content come to 600 μg/g.     

A novel method for the spectrophotometric determination of nitrite in water

A rapid, simple, selective and sensitive method for the spectrophotometric determination of nitrite in water has been developed and optimum reaction conditions along with other analytical parameters have been evaluated. Nitrite reacts with barbituric acid in acidic solution to give the nitroso derivative, violuric acid. At analytical wavelength of 310 nm, Beer's law is obeyed over the concentration range 0.00–3.22 ppm of nitrite. The molar absorptivity is 15330 ± 259.7 (95%) with pooled standard deviation of 355.57 and R.S.D. of 2.32%. As well as the method is sensitive (2.99 × 10⁻³ μg NO₂ cm⁻²) and selective, it tolerates most of the potential interferents. It has been successfully applied to nitrite determination in natural waters by use of a calibration graph with determination limit of 1.66 μg NO₂ in 100 mL working solution corresponding to minimum 9.5 ppb NO₂–N in water samples. Lower concentrations of nitrite (3.0 μg NO₂/L sample) is precisely analyzed by using the method of dilution with sample, with R.S.D. of lower than 0.5%. The results were compared with standard N-(1-naphtyl)ethylenediamine dihydrochloride method and very good agreement between the data was observed. The method can easily be applied in the field.     

Application of diffusive gradient in thin films technique (DGT) to measurement of mercury in aquatic systems

The diffusive gradient in thin films (DGT) technique was investigated and used to measure mercury concentration in river water. Mercury ions are covalently bound to amide nitrogen groups of commonly used polyacrylamide, which makes this gel unsuitable as a diffusive medium. In contrast, agarose gel was found as the diffusive gel for mercury measurements. Basic performance tests of agarose DGT verified the applicability of Fick's first law for DGT measurements. Two selective resins, Chelex-100 with iminodiacetic groups and Spheron-Thiol with thiol groups were used. The measured diffusion coefficient in agarose gel was close to that in water. The concentration of mercury in Svitava river measured by DGT with Speron-Thiol resin gel was higher (0.0116 ± 0.0009 μg l⁻¹) than those obtained by Chelex-100 (0.0042 ± 0.0005 μg l⁻¹). Different capture efficiencies of two adsorbents enable to estimate fractions of mercury bonded in different complexes in the river water. The concentrations of mercury found by DGT both Chelex-100 and Speron-Thiol resin gels are much lower than that measured directly in the river water (0.088 ± 0.012 μg l⁻¹). This difference indicates that DGT concerns inorganic ions and labile species only, and that it is not able to include inert organic species and colloids.     

Simultaneous determination of bromide and nitrate in contaminated waters by ion chromatography using amperometry and absorbance detectors

This study describes a new ion chromatography method using a low-capacity anion exchange column with amperometric and absorbance detection for rapid and simultaneous determination of Br⁻ and NO₃⁻ in contaminated waters where one of these ions is present in excess compared to other. The use of two detectors overcomes the problem of baseline separation for Br⁻ and NO₃⁻ for accurate quantification, which was commonly encountered when using a low-capacity anion exchange column and suppressed conductivity detection mode. The method achieved accurate quantification of these two ions without requirement of baseline separation. The accuracy of 2.8% for NO₃⁻ was determined using a quality control sample obtained from UN GEMS/Water PE Study No. 6. The detection limits for Br⁻ and NO₃⁻ were 20 and 6 μg l⁻¹ (25 μl sample), respectively. Linearity of these two ions was over three orders of magnitude with a correlation coefficient >0.998. The influence of potential interfering ions was also studied followed by the determination of Br⁻ and NO₃⁻ in seawater, unsaturated zone water, soil extract and groundwater.     

Protein-adsorption-resistance and permeation property of polyethersulfone and soybean phosphatidylcholine blend ultrafiltration membranes

Novel ultrafiltration membranes were prepared by simple blending of polyethersulfone (PES) and soybean phosphatidylcholine (SPC). X-ray photoelectron spectroscopy (XPS) and water contact angle measurements indicated SPC enrichment at the membrane surfaces. The immobilization and arrangement of PC groups at surfaces rendered the membranes more hydrophilic. BSA adsorption amount decreased from 56.2 μg/cm² for SPC-free PES membrane to 2.4 μg/cm² for PES/SPC blend membrane. The fouling-resistant property of the blend membranes was improved considerably with an increase of SPC content while the pure water permeation flux decreased remarkably. Using PEG/PVP mixture instead of PEG as pore-forming agent increased pure water flux of PES/SPC blend membrane to some extent.     

Determination of chlorite in drinking water by on-line coupling of capillary isotachophoresis and capillary zone electrophoresis

An isotachophoresis (ITP)–capillary zone electrophoresis (CZE) combination was used for the determination of chlorite in drinking waters. No sample preparation is needed and no interfering by other anions in tap water was observed. The reached limits of detection with conductivity detector were 0.012–0.017 mg l⁻¹. By four-fold sample loading with a 30 μl valve, 0.005 mg l⁻¹ of chlorite was determined with R.S.D.=3.3%. The concentrations of 0.05 and 0.20 mg l⁻¹ were measured with R.S.D. of 2.2 and 2.7%, respectively. The recoveries of chlorite from drinking water were 96–106% in the range of 0.02–0.20 mg l⁻¹. The R.S.D. values of migration times (inter-day) were up to 1.3%. The time for analysis is about 15 min.     

Differential-pulse voltammetric determination of low μg l cyanide levels using EDTA, Cu(II) and a hanging mercury drop electrode

The proposed method for cyanide determination at the ultratrace level by differential pulse voltammetry is based in the sensitivity enhancement obtained when both Cu(II) and EDTA are present in the background electrolyte. Comparison of the detection limits and linear dynamic ranges using the conventional borate (pH 9.75), and the proposed borate-EDTA–Cu(II) background electrolytes was carried out. Best results have been obtained with the addition of 0.5 mmol l⁻¹ EDTA and 0.02 mmol l⁻¹ of Cu(II), which allow a detection limit of 1.7 μg l⁻¹ CN⁻ (65 nmol l⁻¹ — absolute detection limit 34 ng) with a precision better than ±2% for a 40 μg l⁻¹ level. Calibration range extended from detection limit up to 100 μg l⁻¹. Cyclic voltammetry indicates that the measured cyanide peak is obtained when the electrogenerated CuCN adsorbed onto the hanging mercury drop electrode surface, is oxidised at positive going potential scan. The method has been successfully applied to various industrial waste waters such as metal-finishing waste waters, water/sand mixtures from cleaning processes of coke production, leachates from wastes obtained from electrolytic cells of aluminium production, and liquors from gold extraction industry. Results obtained by the proposed method showed good agreement with those obtained by the standard methods (ion-selective potentiometry and the spectrophotometric pyridine method).     

A multicommuted stop-flow system employing LEDs-based photometer for the sequential determination of anionic and cationic surfactants in water

It has been developed an automatic stop-flow procedure for sequential photometric determination of anionic and cationic surfactants in a same sample of water. The flow system was based on multicommutation process that was designed employing two solenoid micro-pumps and six solenoid pinch valves, which under microcomputer control carry out fluid propelling and reagent solutions handling. A homemade photometer using a photodiode as detector and two light emitting diodes (LEDs) with emission at 470 nm (blue) and 650 nm (red) as radiation sources, which was tailored to allow the determination of anionic and cationic surfactants in waters. The procedure for anionic surfactant determination was based on the substitution reaction of methyl orange (MO) by the anionic surfactant sodium dodecylbenzene sulfonate (DBS) to form an ion-pair with the cetyl pyridine chloride (CPC). Features such as a linear response ranging from 0.35 to 10.5 mg L⁻¹ DBS (R = 0.999), a detection limit of 0.06 mg L⁻¹ DBS and a relative standard deviation of 0.6% (n = 11) were achieved. For cationic surfactant determination, the procedure was based on the ternary complex formation between cationic surfactant, Fe(III) and chromazurol S (CAS) using CPC as reference standard solution. A linear response range between 0.34 and 10.2 mg L⁻¹ CPC (R = 0.999), a detection limit of 0.05 mg L⁻¹ CPC and a relative standard deviation of 0.5% (n = 11) were obtained. In both cases, the sampling throughput was 60 determinations per hour. Reagents consumption of 7.8 μg MO, 8.2 μg CPC, 37.2 μg CAS and 21.6 μg Fe(III) per determination were achieved. Analyzing river water samples and applying t-test between the results found and those obtained using reference procedures for both surfactant types provide no significant differences at 95% confidence level.     

Optimisation of sample treatment for arsenic speciation in alga samples by focussed sonication and ultrafiltration

A procedure for arsenic species fractionation in alga samples (Sargassum fulvellum, Chlorella vulgaris, Hizikia fusiformis and Laminaria digitata) by extraction is described. Several parameters were tested in order to evaluate the extraction efficiency of the process: extraction medium, nature and concentration (tris(hydroxymethyl)aminomethane, phosphoric acid, deionised water and water/methanol mixtures), extraction time and physical treatment (magnetic stirring, ultrasonic bath and ultrasonic focussed probe). The extraction yield of arsenic under the different conditions was evaluated by determining the total arsenic content in the extracts by ICP-AES. Arsenic compounds were extracted in 5 mL of water by focussed sonication for 30 s and subsequent centrifugation at 14,000 × g for 10 min. The process was repeated three times. Extraction studies show that soluble arsenic compounds account for about 65% of total arsenic.

An ultrafiltration process was used as a clean-up method for chromatographic analysis, and also allowed us to determine the extracted arsenic fraction with a molecular weight lower than 10 kDa, which accounts for about 100% for all samples analysed.

Speciation studies were carried out by HPLC–ICP-AES. Arsenic species were separated on a Hamilton PRP-X100 column with 17 mM phosphate buffer at pH 5.5 and 1.0 mL min⁻¹ flow rate. The chromatographic method allowed us to separate the species As(III), As(V), MMA and DMA in less than 13 min, with detection limits of about 20 ng of arsenic per species, for a sample injection volume of 100 μL. The chromatographic analysis allowed us to identify As(V) in Hizikia (46 ± 2 μg g⁻¹), Sargassum (38 ± 2 μg g⁻¹) and Chlorella (9 ± 1 μg g⁻¹) samples. The species DMA was also found in Chlorella alga (13 ± 1 μg g⁻¹). However, in Laminaria alga only an unknown arsenic species was detected, which eluted in the dead volume.     

Determination of phenols in water by on-line solid-phase disk extraction and liquid chromatography with electrochemical detection

Poly(styrene-divinylbenzene) (PS-DVB) membrane extraction disks were used as sorbents for the on-line solid phase extraction of 13 phenols (nitro and chlorophenols) in river and tap waters. Determination was performed by liquid chromatography with electrochemical detection (LC-ED). An acetate buffer-acetonitrile-methanol mixture as mobile phase and amperometric detection at +1100 mV were used. High water volumes, up to 250 ml, can be preconcentrated without loss of phenols (recoveries between 80% and 100%) except for the more polar ones. Moreover, detection limits between 0.01 and 0.1 μg l⁻¹ in tap water and between 0.1 and 1.0 μg⁻¹ in river water were obtained. The method has been applied to the analysis of two river water samples.     

Synthesis, structure, and fluorescence of two cadmium(II)-citrate coordination polymers with different coordination architectures

Two novel Cd(II)-citrate complexes were obtained with different metal/ligand ratios through hydrothermal method. Their structures were determined by single-crystal X-ray diffraction analysis. Although their topological structures are both 2-D layer network assemblies, both central Cd(II) ions and Hcit³⁻ ligands display completely different coordination modes. In polymeric complex 1, Hcit³⁻ serves as a μ₁₀-bridged and central Cd(II) ions adopt 6- and 8-coordinated configurations. In contrast, a μ₉-bridged and 6- and 7-coordinated environments between Cd(II) and Hcit³⁻ are established in the polymeric complex 2. Two Complexes remain stable up to approximately 300 °C. The complex 1 exhibits strong fluorescent emission band at 450 nm (λ=346 nm) as well as complex 2 exhibits strong fluorescent emission band at 430 (λ=346 nm).     

Trace analysis of chlorobenzenes in water samples using headspace solvent microextraction and gas chromatography/electron capture detection

In the present work, a rapid method for the extraction and determination of chlorobenzenes (CBs) such as monochlorobenzene, 1,2-dichlorobenzene, 1,3-dichlorobenzene, 1,4-dichlorobenzene, 1,2,3-trichlorobenzene and 1,2,4-trichlorobenzene in water samples using the headspace solvent microextraction (HSME) and gas chromatography/electron capture detector (ECD) has been described. A microdrop of the dodecane containing monobromobenzene (internal standard) was used as extracting solvent in this investigation. The analytes were extracted by suspending a 2.5 μl extraction drop directly from the tip of a microsyringe fixed above an extraction vial with a septum in a way that the needle passed through the septum and the needle tip appeared above the surface of the solution. After the extraction was finished, the drop was retracted back into the needle and injected directly into a GC column. Optimization of experimental conditions such as nature of the extracting solvent, microdrop and sample temperatures, stirring rate, microdrop and sample volumes, the ionic strength and extraction time were investigated. The optimized conditions were as follows: dodecane as the extracting solvent, the extraction temperature, 45 °C; the sodium chloride concentration, 2 M; the extraction time, 5.0 min; the stirring rate, 500 rpm; the drop volume, 2.5 μl; the sample volume, 7 ml; the microsyringe needle temperature, 0.0 °C. The limit of detection (LOD) ranged from 0.1 μg/l (for 1,3-dichlorobenzene) to 3.0 μg/l (for 1,4-dichlorobenzene) and linear range of 0.5–3.0 μg/l for 1,2-dichlorobenzene, 1,3-dichlorobenzene and from 5.0 to 20.0 μg/l for monochlorobenzene and from 5.0 to 30 μg/l for 1,4-dichlorobenzene. The relative standard deviations (R.S.D.) for most of CBs at the 5 μg/l level were below 10%. The optimized procedure was successfully applied to the extraction and determination of CBs in different water samples.