Optimization of DNA hybridization efficiency by pH-driven nanomechanical bending

The accessibility and binding affinity of DNA are two key parameters affecting the hybridization efficiency in surface-based biosensor technologies. Better accessibility will result in a higher hybridization efficiency. Often, mixed ssDNA and mercaptohexanol monolayers are used to increase the hybridization efficiency and accessibility of surface-bound oligonucleotides to complementary target DNA. Here, no mercaptohexanol monolayer was used. We demonstrate by differential microcantilever deflection measurements at different pH that the hybridization efficiency peaks between pH 7.5 and 8.5. At low pH 4.5, hydration and electrostatic forces led to tensile surface stress, implying the reduced accessibility of the bound ssDNA probe for hybridization. In contrast, at high pH 8.5, the steric interaction between neighboring ssDNA strands was decreased by higher electrostatic repulsive forces, bending the microcantilever away from the gold surface to provide more space for the target DNA. Cantilever deflection scales with pH-dependent surface hybridization efficiency because of high target DNA accessibility. Hence, by changing the pH, the hybridization efficiency is adjusted.     

Chemomechanics of surface stresses induced by DNA hybridization

When biomolecular reactions occur on one surface of a microcantilever beam, changes in intermolecular forces create surface stresses that bend the cantilever. While this phenomenon has been exploited to create label-free biosensors and biomolecular actuators, the mechanisms through which chemical free energy is transduced to mechanical work in such hybrid systems are not fully understood. To gain insight into these mechanisms, we use DNA hybridization as a model reaction system. We first show that the surface grafting density of single-stranded probe DNA (sspDNA) on a surface is strongly correlated to its radius of gyration in solution, which in turn depends on its persistence length and the DNA chain length. Since the persistence length depends on ionic strength, the grafting density of sspDNA can be controlled by changing a solution's ionic strength. The surface stresses produced by the reaction of complementary single-stranded target DNA (sstDNA) to sspDNA depend on the length of DNA, the grafting density, and the hybridization efficiency. We, however, observe a remarkable trend: regardless of the length and grafting density of sspDNA, the surface stress follows an exponential scaling relation with the density of hybridized sspDNA.     

Characterization of grafting density and binding efficiency of DNA and proteins on gold surfaces

The surface grafting density of biomolecules is an important factor for quantitative assays using a wide range of biological sensors. We use a fluorescent measurement technique to characterize the immobilization density of thiolated probe DNA on gold and hybridization efficiency of target DNA as a function of oligonucleotide length and salt concentration. The results indicate the dominance of osmotic and hydration forces in different regimes of salt concentration, which was used to validate previous simulations and to optimize the performance of surface-stress based microcantilever biosensors. The difference in hybridization density between complementary and mismatched target sequences was also measured to understand the response of these sensors in base-pair mismatch detection experiments. Finally, two different techniques for immobilizing proteins on gold were considered and the surface densities obtained in both cases were compared.     

Monitoring the hydration of DNA self-assembled monolayers using an extensional nanomechanical resonator

We have fabricated an ultrasensitive nanomechanical resonator based on the extensional vibration mode to weigh the adsorbed water on self-assembled monolayers of DNA as a function of the relative humidity. The water adsorption isotherms provide the number of adsorbed water molecules per nucleotide for monolayers of single stranded (ss) DNA and after hybridization with the complementary DNA strand. Our results differ from previous data obtained with bulk samples, showing the genuine behavior of these self-assembled monolayers. The hybridization cannot be inferred from the water adsorption isotherms due to the low hybridization efficiency of these highly packed monolayers. Strikingly, we efficiently detect the hybridization by measuring the thermal desorption of water at constant relativity humidity. This finding adds a new nanomechanical tool for developing a label-free nucleic acid sensor based on the interaction between water and self-assembled monolayers of nucleic acids.     

Nanomechanical actuation driven by light-induced DNA fuel

We report the reversible nanomechanical actuation of a microcantilever driven by the light irradiation-induced conformational changes of i-motif DNA chains, which are functionalized on the cantilever's surface. It is shown that light irradiation-driven nanomechanical actuation can be manipulated using DNA hybridization and/or ionic concentrations.     

Nanomechanical sensing of DNA sequences using piezoresistive cantilevers

A microfabricated cantilever with an internal piezoresistive component has been sensitized with thiol tethered ss-DNA strands and utilized for an in situ, label-free, highly specific, and rapid DNA detection assay. The generation of a differential surface stress onto the functionalized cantilever surface upon target recognition has allowed nanomechanical identification of 12-nucleotide complementary DNA probes with single base mismatch discrimination (sensitivity of 0.2 microM). Interestingly, utilization of an overhang extension distal to the surface enhanced the sensitivity to the 0.01 microM level. The cantilever was functionalized by inkjet printing technology. Replacing the capture probe with locked nucleic acid (LNA) resulted in a faster target probe capture kinetics compared to DNA-DNA hybridization. The capabilities of the piezoresistive cantilever indicate future ergonomic convenience via miniaturization alternative to the conventional laser-based detection method for portable on-site applications.     

Effect of salt on the hybridization of DNA by sequential immobilization of oligonucleotides at the air-water interface in the presence of ODA/DOTAP monolayers

The effect of low ionic strength on the binding of preformed DNA duplexes and the hybridization of single-stranded oligonucleotides at the air-water interface in the presence of cationic Langmuir monolayers of octadecylamine (ODA), as well as 1,2-dioleoyloxytrimethylammonium propane (DOTAP), is investigated. The complexation of the single-stranded DNA molecules and preformed duplexes with NaCl in solution with ODA/DOTAP Langmuir monolayers was followed in time by monitoring the pressure-area isotherms, wherein a very large and rapid expansion of the ODA/DOTAP monolayer was observed. In the case of sequential immobilization of complementary oligonucleotides, after addition of the complementary strand and intercalator, there was not much expansion, indicative of the fact that equilibrium had been rapidly achieved. Langmuir-Blodgett (LB) films of the ODA/DOTAP-DNA complex were formed on different substrates and characterized using quartz-crystal microgravimetry (QCM), fluorescence spectroscopy, and thermal melting studies. These measurements clearly showed that the preformed duplexes retained their native form as double helices and further, hybridization of the complementary single-stranded DNA molecules had occurred at the air-water interface, leading to the characteristic double-helical structure.     

Use of biospecific reactions for the design of high-sensitivity biosensors based on nanomechanical cantilever systems

The study of nanomechanical cantilever systems is among the priority directions in the progression of nanotechnologies. Principally new ways of designing biosensors based on nanocantilever transducers are investigated, the effect of orientation of receptor immunoglobulin molecules in the sensor layer on the formation of lateral strain during complementary binding is examined for the first time, and unique techniques for creation of selective receptor transducers based on cantilevers are developed. The unique data of this study make it possible to state that, owing to the presence of 13-thiotridecane-1,1,2-triol molecules in the probe DNA layer, the lateral strain tends to increase during hybridization of complementary molecules. Theoretical predictions and experimental data are compared, and the effect of the formation of lateral strain in polymer layers on the bending of the cantilever transducer is revealed. The nature of lateral strain arising in films of biopolymers (proteins and DNA) during complementary binding (formation of the immune complex for protein molecules and hybridization for DNA) is ascertained.     

Site-selective immobilization of gold nanoparticles functionalized with DNA oligomers

The organization of metal and semiconductor nanoparticles to form micro- and nanostructured assemblies is currently of tremendous interest. This communication reports on the utilization of DNA molecules as positioning elements for generating microstructured surface architecture from gold nanoparticles. Citrate-passivated 40 nm gold colloids were modified by chemisorptive coupling with a 5′-thiol-derivatized DNA oligomer. The nucleic acid was used as a molecular handle for the specific immobilization on solid supports, previously functionalized with capture DNA oligomers, complementary to the nanoparticle-bound DNA. As a consequence of the enormous specificity of nucleic acid hybridization, the DNA-directed immobilization (DDI) allows, to site-specifically target the hybrid nanoparticles to microlocations which contain the complementary oligomers. The site-selectivity of the surface adsorption is demonstrated by immobilizing the gold colloids on a DNA microarray on a glass cover slide. Moreover, scanning force microscopy (SFM) analysis, used to characterize the intermediate steps of the DDI on a gold substrate, provided initial insights into the specificity and efficiency of this technique. The application of the DDI to fabricate complex colloidal micro- and nanostructures is anticipated. Received: 26 July 2000/Accepted: 5 October 2000     

Probing DNA hybridization in thiolipid monolayers by means of impedance spectroscopy

A composite monolayer consisting of a thiolipid and a nucleic acid probe (1), acts as a microenvironment for probing hybridization with the complementary strand (2) by means of impedance spectroscopy. The impedance measurements indicate a significant decrease in the resistance at the electrode surface upon the formation of the (1)/(2) duplex. The impedance measurements were performed in the absence of any amplifying label or added redox label. In order to characterize the electrodes surface and to follow the immobilization processes kinetics, surface plasmon resonance measurements were performed.     

Electrochemical Quantitative Analysis of Nucleic Acids Using β‐Cyclodextrin Modified Gold Electrode

We present an electrochemical biosensor for the analysis of nucleic acids upon hybridization on the β‐cyclodextrin (β‐CD)‐modified gold electrode. The strategy is based on the following: The 5’‐ferrocene‐labeled single stranded capture probe DNA (5’‐fc‐ss‐DNA) was incorporated into the cavity of thiolated β‐CD which was immobilized on the surface of gold electrode. After hybridization of complementary target DNA, hybridized double stranded DNA (ds‐DNA) was released from the cavity of β‐CD. The difference of electrochemical properties on the modified gold electrode was characterized by cyclic voltametry and surface plasmon resonance. We successfully applied this method to the investigation of the sensor responses due to hybridization on various concentrations of applied target DNA. As a result, the label‐free electrochemical DNA sensor can detect the target DNA with a detection limit of 1.08 nM. Finally, our method does not require either hybridization indicators or other signalling molecules such as DNA intercalaters which most of electrochemical hybridization detection systems require.     

Mechano-transduction of DNA hybridization and dopamine oxidation through electrodeposited chitosan network

While microcantilevers offer exciting opportunities for mechano-detection, they often suffer from limitations in either sensitivity or selectivity. To address these limitations, we electrodeposited a chitosan film onto a cantilever surface and mechano-transduced detection events through the chitosan network. Our first demonstration was the detection of nucleic acid hybridization. In this instance, we electrodeposited the chitosan film onto the cantilever, biofunctionalized the film with oligonucleotide probe, and detected target DNA hybridization by cantilever bending in solution (static mode) or resonant frequency shifts in air (dynamic mode). In both detection modes, we observed a two-order of magnitude increase in sensitivity compared to values reported in literature for DNA immobilized on self-assembled monolayers. In our second demonstration, we coupled electrochemical and mechanical modes to selectively detect the neurotransmitter dopamine. A chitosan-coated cantilever was biased to electrochemically oxidize dopamine solution. Dopamine's oxidation products react with the chitosan film and create a tensile stress of approximately 1.7 MPa, causing substantial cantilever bending. A control experiment was performed with ascorbic acid solution. It was shown that the electrochemical oxidation of ascorbic acid does not lead to reactions with chitosan and does not change cantilever bending. These results suggest that chitosan can confer increased sensitivity and selectivity to microcantilever sensors.     

杂交及切断过程的QCM实时检测研究(英文)

采用自组装技术,将 5′端标记有巯基的 20-merODN(oligo 1)以金 硫键形式牢固结合在 7. 995MHz的AT-切石英晶体的镀金表面,然后由石英晶体微天平实时检测了与碱基序列互补的 10 merODN (oligo 2)和 8 merODN(oligo 3)的杂交,同时还研究了稀土金属铈离子在温和条件下对DNA的水解切断作用.结果表明:应用QCM方法可能实时检测DNA的固定和杂交,Ce(IV)能随机切断单链DNA;但不能切断杂交形成的双链DNA,因此可利用杂交保护的方法对单链DNA实行定位切断.     

Direct selective detection of genomic DNA from coliform using a fiber optic biosensor

Fiber optic biosensors operated in a total internal reflection format were prepared based on covalent immobilization of 25mer lacZ single-stranded nucleic acid probe. Genomic DNA from Escherichia coli was extracted and then sheared by sonication to prepare fragments of approximately 300mer length. Other targets included a 25mer fully complementary lacZ sequence, 100mer polymerase chain reaction (PCR) products containing the lacZ sequence at various locations, and non-complementary DNA including genomic samples from salmon sperm. Non-selective adsorption of non-complementary oligonucleotides (ncDNA) was found to occur at a significantly faster rate than hybridization of complementary oligomers (cDNA) in all cases. The presence of ncDNA oligonucleotides did not inhibit selective interactions between immobilized DNA and cDNA in solution. The presence of high concentrations of non-complementary genomic DNA had little effect on extent or speed of hybridization of complementary oligonucleotides. Detection of genomic fragments containing the lacZ sequence was possible in as little as 20 s by observation of the steady-state fluorescence intensity increase or by time-dependent rate of fluorescence intensity changes.     

A low-cost surface plasmon resonance instrument based on detection of resonance excitation wavelength

A laboratory-made surface plasmon resonance (SPR) instrument based on the detection of resonance excitation wavelength has been successfully fabricated. The performance and workability of the SPR instrument was demonstrated as a DNA biosensor. Biotinylated single-stranded oligonucleotides (ssDNA) were chemically immobilized on a gold-film surface of the SPR instrument as a DNA probe for the detection of its fully complementary, half-complementary and non-complementary ssDNA. The immobilization of the ssDNA probe was done by avidin-biotin linkage. The ssDNA used were 12-mer oligonucleotides. The sensing mechanism was based on the shift in resonance wavelength of an excitation light beam as the target ssDNA hybridized with the ssDNA on the gold-film surface. The linear dynamic ranges of the DNA biosensor for fully complementary and half-complementary ssDNA are 0.04-1.2 pM and 0.08-1.1 pM, respectively. The DNA biosensor showed higher sensitivity to fully complementary ssDNA than to half-complementary ssDNA. But no shift of resonance wavelength to the non-complementary ssDNA was observed.     

Determining the folding and unfolding rate constants of nucleic acids by biosensor. Application to telomere G-quadruplex

Nucleic acid molecules may fold into secondary structures, and the formation of such structures is involved in many biological processes and technical applications. The folding and unfolding rate constants define the kinetics of conformation interconversion and the stability of these structures and is important in realizing their functions. We developed a method to determine these kinetic parameters using an optical biosensor based on surface plasmon resonance. The folding and unfolding of a nucleic acid is coupled with a hybridization reaction by immobilization of the target nucleic acid on a sensor chip surface and injection of a complementary probe nucleic acid over the sensor chip surface. By monitoring the time course of duplex formation, both the folding and unfolding rate constants for the target nucleic acid and the association and dissociation rate constants for the target-probe duplex can all be derived from the same measurement. We applied this method to determine the folding and unfolding rate constants of the G-quadruplex of human telomere sequence (TTAGGG)(4) and its association and dissociation rate constants with the complementary strand (CCCTAA)(4). The results show that both the folding and unfolding occur on the time scale of minutes at physiological concentration of K(+). We speculate that this property might be important for telomere elongation. A complete set of the kinetic parameters for both of the structures allows us to study the competition between the formation of the quadruplex and the duplex. Calculations indicate that the formation of both the quadruplex and the duplex is strand concentration-dependent, and the quadruplex can be efficiently formed at low strand concentration. This property may provide the basis for the formation of the quadruplex in vivo in the presence of a complementary strand.     

UV cross-linking of unmodified DNA on glass surfaces

The performance of DNA microarrays strongly depends on their surface properties. Furthermore, the immobilization method of the capture molecules is of importance for the efficiency of the microarray in terms of sensitivity and specificity. This work describes the immobilization of single-stranded capture oligonucleotides by UV cross-linking on silanated (amino and epoxy) glass surfaces. Thereby we used amino (NH₂) and poly thymine/poly cytosine modifications of the capture sequences as well as unmodified capture molecules. The results were compared to UV cross-linking of the same DNA oligonucleotides on unmodified glass surfaces. Immobilization and hybridization efficiency was demonstrated by fluorescence and enzyme-induced deposition of silver nanoparticles. We found out that single-stranded DNA molecules do not require a special modification to immobilize them by UV cross-linking on epoxy- or amino-modified glass surfaces. However, higher binding rates can be achieved when using amino-modified oligonucleotides on an epoxy surface. The limit of detection for the used settings was 5 pM.     

Amplified surface plasmon resonance based DNA biosensors, aptasensors, and Hg2+ sensors using hemin/G-quadruplexes and Au nanoparticles

Thiolated nucleic acid hairpin nanostructures that include in their stem region a "caged" G-quadruplex sequence, and in their single-stranded loop region oligonucleotide recognition sequences for DNA, adenosine monophosphate (AMP), or Hg(2+) ions were linked to bare Au surfaces or to Au nanoparticles (NPs) linked to Au surfaces. The opening of the hairpin nanostructures associated with the bare Au surface by the complementary target DNA, AMP substrate, or Hg(2+) ions, in the presence of hemin, led to the self-assembly of hemin/G-quadruplexes on the surface. The resulting dielectric changes on the surface exhibited shifts in the surface plasmon resonance (SPR) spectra, thus providing a readout signal for the recognition events. A similar opening of the hairpin nanostructures, immobilized on the Au NPs associated with the Au surface, by the DNA, AMP, or Hg(2+) led to an ultrasensitive SPR-amplified detection of the respective analytes. The amplification originated from the coupling between the localized surface plasmon associated with the NPs and the surface plasmon wave, an effect that cooperatively amplifies the SPR shifts that result from the formation of the hemin/G-quadruplexes. The different sensing platforms reveal impressive sensitivities and selectivities toward the target analytes.     

Specific molecule localization in microchannel laminar flow and its application for non-immobilized-probe analysis

Microfluidic systems enable superior control of fluidics. We have developed a novel size-separation method utilizing secondary flow within a microchannel. Using confocal fluorescence microscopy and computer simulation, we confirmed that separation occurred as a result of specific molecular localization in the curving part of the microchannel. Maximum separation efficiency was achieved by optimizing microchannel design and flow rate for individual separation targets. In addition, more effective separation was achieved by use of plural microchannel curves. This method was used for sequence-selective DNA sensing. Double-stranded DNA formed by hybridization between target DNA and a complementary probe had different elution profiles from those of the single-stranded non-complementary sequence. Moreover, the response depends on the length of the DNA molecules. This method does not require immobilization of either probe or target DNA, because all reactions occurred in the solution phase. Such features may reduce experimental error and the difference between data from different operators.     

Influences of non-selective interactions of nucleic acids on response rates of nucleic acid fiber optic biosensors

The immobilization of oligonucleotides to solid surfaces can provide a platform of chemistry that is suitable for the development of biosensor and microarray technologies. Experiments were performed using a fiber optic nucleic acid biosensor based on total internal reflection fluorescence to examine the effects of the presence of non-complementary DNA on the detection of hybridization of complementary target DNA. The work has focused on the rates and extent of hybridization in the presence and absence of non-selective adsorption using fluorescein-labeled DNA. A stop-flow system of 137 microL volume permitted rapid introduction and mixing of each sample. Response times measured were on the order of seconds to minutes. Non-selective adsorption of non-complementary oligonucleotides (ncDNA) was found to occur at a significantly faster rate than hybridization of complementary oligomers (cDNA) in all cases. The presence of ncDNA oligonucleotides did not inhibit selective interactions between immobilized DNA and cDNA in solution. The presence of high concentrations of non-complementary genomic DNA had little effect on the extent of hybridization of complementary oligonucleotides, but actually reduced the response times of sensors to cDNA oligonucleotides.