DNP-EPR多功能谱仪中微波桥的设计与实现

在自主研制的动态核极化（Dynamic Nuclear Polarization,DNP）分子影像装置的基础上,提出了一种集DNP和电子顺磁共振（Electron Paramagnetic Resonance,EPR）于一体的多功能谱仪,并对其中的关键部件之一--微波桥进行了设计.微波桥的引入,实现了DNP微波发射机的集成化,以及在DNP谱仪基础上的EPR功能扩展.通过结构设计、电路仿真及系统测试,完成了高频谱纯度、高动态范围的微波发射机以及低噪声系数的微波检测系统的设计与制作.并通过DNP增强实验以及连续波EPR实验对微波桥的性能进行了验证.     

Analysis of the tuning and operation of reflection resonator EPR spectrometers

This paper investigates basic characteristics of the electron paramagnetic resonance (EPR) signal obtained from spectrometers employing reflection resonators. General equations are presented which reveal the phase and amplitude dependence on instrumental parameters of both components of the continuous wave (CW) EPR signal (absorption and dispersion). New phase vector diagrams derived from these general equations are presented for the analysis of the EPR response. The dependence of the phase and absolute value of the CW EPR signal on the local oscillator (LO) phase and on resonator offset and coupling is presented and analyzed. The EPR spectrometer tuning procedures for both balanced and unbalanced heterodyne receivers are analyzed in detail using the new phase diagrams. Extraneous signals at the RF input of the microwave receiver (resulting from circulator leakage and reflections in the resonator transmission line) have been taken into account and analyzed. It is shown that a final tuning condition that corresponds to an extremum of the receiver output as a function of the resonator frequency is necessary and sufficient for the acquisition of pure absorption signal. This condition is universal: it applies to all spectrometer configurations in all frequency ranges. High Frequency EPR spectrometer (130 GHz) data are used to generate experimental phase diagrams that illustrate the theoretical concepts presented in the paper. Conditions are presented under which the absorption signal can be measured with complete suppression of the dispersion, independent of the mutual frequency offset between the microwave source and the EPR sample resonator. Equations describing the approximate relationship between changes of the resonator properties (Q-factor and frequency) and paramagnetic susceptibility are derived and analyzed.     

Detection of electron paramagnetic resonance absorption using frequency modulation

A frequency modulation (FM) method was developed to measure electron paramagnetic resonance (EPR) absorption. The first-derivative spectrum of 1,1-diphenyl-2-picrylhydrazyl (DPPH) powder was measured with this FM method. Frequency modulation of up to 1.6 MHz (peak-to-peak) was achieved at a microwave carrier frequency of 1.1 GHz. This corresponds to a magnetic field modulation of 57microT (peak-to-peak) at 40.3 mT. By using a tunable microwave resonator and automatic control systems, we achieved a practical continuous-wave (CW) EPR spectrometer that incorporates the FM method. In the present experiments, the EPR signal intensity was proportional to the magnitude of frequency modulation. The background signal at the modulation frequency (1 kHz) for EPR detection was also proportional to the magnitude of frequency modulation. An automatic matching control (AMC) system reduced the amplitude of noise in microwave detection and improved the baseline stability. Distortion of the spectral lineshape was seen when the spectrometer settings were not appropriate, e.g., with a lack of the open-loop gain in automatic tuning control (ATC). FM is an alternative to field modulation when the side-effect of field modulation is detrimental for EPR detection. The present spectroscopic technique based on the FM scheme is useful for measuring the first derivative with respect to the microwave frequency in investigations of electron-spin-related phenomena.     

Pulsed EPR imaging of nitroxides in mice

Nitroxides, unlike trityl radicals, have shorter T₂s which until now were not detectable in vivo by a time-domain pulsed Electron Paramagnetic Resonance (EPR) spectrometer at 300 MHz since their phase memory times were shorter than the spectrometer recovery times. In the current version of the time-domain EPR spectrometer with improved spectrometer recovery times, the feasibility of detecting signals from nitroxide radicals was tested. Among the nitroxides evaluated, deuterated ¹⁵N-Tempone (¹⁵N-PDT) was found to have the longest T₂. The signal intensity profile as a function of concentration of these agents was evaluated and a biphasic behavior was observed; beyond a nitroxide concentration of 1.5 mM, signal intensity was found to decrease as a result of self-broadening. Imaging experiments were carried out with ¹⁵N-PDT in solutions equilibrated with 0%, 5%, 10%, and 21% oxygen using the single point imaging (SPI) modality in EPR. The image intensity in these tubes was found to depend on the oxygen concentration which in turn influences the T₂ of ¹⁵N-PDT. In vivo experiments were demonstrated with ¹⁵N-PDT in anesthetized mice where the distribution and metabolism of ¹⁵N-PDT could be monitored. This study, for the first time shows the capability to image a cell-permeable nitroxide in mice using pulsed EPR in the SPI modality.     

在体剂量检测专用EPR数据采集与控制系统

研制了X波段在体剂量检测专用EPR谱仪的数据采集与控制系统,利用阿尔泰USB2812数据采集卡作为控制卡,在LabVIEW图形化编程开发环境中进行程序开发,实现了扫场电源的控制、微波模的显示、微波功率的控制和EPR信号的采集等功能. 数据处理程序可实现存储数据的查询、谱线基线校正和积分等基本功能,为下一步开展牙齿剂量试验研究提供了平台.     

EPR spectroscopy and imaging of TEMPO-labeled magnetite nanoparticles

The article presents results of a study of TEMPO-labeled polymer coated superparamagnetic iron(II,III) oxide nanoparticles using both Electron Paramagnetic Resonance (EPR) spectroscopy and Electron Paramagnetic Resonance imaging technique (EPRI). The X-band (9.4 GHz) EPR spectroscopy was used to investigate the behavior of TEMPO-labeled polymer coated magnetite nanoparticles in different conditions (temperature and orientation in magnetic field). The broad line, which comes from the core of Fe₃O₄ nanoparticles, shows anisotropy. This signal broadens with decreasing temperature, its intensity increases with increasing temperature and the g factor decreases with increasing temperature. The shape of the signal from nitroxide radical strongly depends on temperature. When temperature is higher than 200 K, a narrow triplet appears, but when it is lower than 200 K the signal consists of broad asymmetric lines. Analysis of the signal allowed characterization of the motion of the spin label attached to nanoparticles. Values of anisotropy parameter ɛ and rotational correlation time τ_c were calculated for TEMPO in the fast rotation regime.The ability of TEMPO-labeled PEG coated magnetite nanoparticles to diffuse within the hydrogel medium was also investigated. The EPR imaging of nanoparticles diffusion in hydrogel was made at room temperature using an EPR L-band (1 GHz) spectrometer. EPRI has been proved effective for evaluation of changes in the spatial distribution of nanoparticles in the sample.     

延长速调管使用寿命的方法

描述了一种延长EPR波谱仪中速调管使用寿命的方法.根据这种方法,只要正确地调谐微波桥的工作状态和适当地调整功率电平器的功率校正电平.即使对于已经严重老化的速调管仍然可以继续使用一段时间,维持仪器的正常运行.     

Analysis of the Movement of Line-like Samples of Variable Length along theX-Axis of a Double TE104and a Single TE102Rectangular Cavity

Movement of line-like samples with lengths from 5 to 50 mm along thex-axis of the double TE₁₀₄rectangular cavity has been analyzed. The observed dependencies of the EPR signal intensity versus sample position showed: (i) a sharp maximum for sample lengths from 5 to 20 mm; (ii) a plateau, over which the EPR signal intensity remained constant within experimental errors of 0.26–1.07%, for lengths from 30 to 40 mm; and (iii) a “sloping plateau,” which could be approximated by the linear function (correlation,r= 0.98) for sample length 50 mm. Theoretical values of the experimentally observed dependencies of the intensity versus sample position were calculated using the modified sine-squared function and the correlation between observed and theoretically predicted dependencies is very good. The experimental dependence of the EPR signal intensity versus the sample length for samples situated at the same point in the cavity was nonlinear with a maximum for the 40-mm sample. The dependence of the EPR signal intensity upon the movement of a large cylindrical sample (o.d. 4 mm and length 100 mm) along thex-axis of the cavity was similar to that found for the 50-mm sample. However, an additional oscillating signal superimposed on the sloping plateau was observed. The presence of a large sample fixed in the complementary cavity of the double TE₁₀₄cavity caused an additional deformation of the signal intensity for a 30-mm sample which was moving in the first cavity. The primary effect was that the plateau was replaced by a region in which the intensity increased linearly with sample position,r= 0.99. Each of the above phenomena may be a source of significant errors in quantitative EPR spectroscopy. Cylindrical samples to be compared should be of identical length and internal diameter. Accurate and precise positioning of each sample in the microwave cavity is essential.     

Electronically tunable surface-coil-type resonator for L-band EPR spectroscopy

The automatic frequency control (AFC) circuit in conventional electron paramagnetic resonance (EPR) spectrometers automatically tunes the microwave source to the resonance frequency of the resonator. The circuit works satisfactorily for samples stable enough that the geometric relations in the resonance structure do not change in a significant way. When EPR signals are measured during in vivo experiments with small rodents, however, the distance between the signal source and the surface-coil detector can change rapidly. When a conventional AFC circuit keeps the oscillator tuned to the resonator under those conditions, the resultant frequency change may exceed +/-5 MHz and markedly shift the position of the EPR signal. Such a shift results in unacceptable effects on the spectra, especially when the experimenter is dealing with narrow EPR lines. The animal movement also causes a mismatching of the resonator and the 50-ohm transmission line. Direct results of this mismatching are increased noise; shifts in the position of the baseline; and a high probability of overdriving the signal preamplifier with consequent loss of the EPR signal. We therefore designed, built, and tested a new surface-coil resonator using varactor diodes for tuning the resonance frequency to the fixed frequency oscillator and for capacitive matching of the resonator to the 50-ohm transmission line. The performance of the automatic matching system was tested in vivo by measuring EPR spectra of lithium phthalocyanine implanted in rats. Stability and sensitivity of the spectrometer were evaluated by measuring EPR spectra with and without the use of the automatic matching system. The overall experimental performance of the spectrometer was found to significantly improve during in vivo experiments using the automatic matching system. Excellent matching between the 50-ohm transmission line and the resonator was maintained under all experimental circumstances that were tested. This should allow us now to carry out experiments that previously were not possible.     

Egyptian limestone for gamma dosimetry: an electron paramagnetic resonance study

The electron paramagnetic resonance (EPR) properties of limestone from a certain Egyptian site were investigated in order to propose an efficient and low-cost gamma dosimeter. Radiation-induced free radicals were of one type which was produced in the limestone samples at g=2.0066 after exposure to gamma radiation (⁶⁰Co). EPR spectrum was recorded and analyzed. The microwave power saturation curve and the effect of changing modulation amplitude on peak-to- peak signal height were investigated. The response of limestone to different radiation doses (0.5–20 kGy) was studied. Except for the decrease in signal intensities during the first five hours following irradiation, over the period of two months fair stabilities of signal intensities were noticed. From the current results, it is possible to conclude that natural limestone may be a suitable material for radiation dosimetry in the range of irradiation processing.     

新型X波段多功能EPR谱仪的设计与性能

本文设计和研制了一款新型X波段多功能电子顺磁共振（electron paramagnetic resonance,EPR）谱仪,并为其开发一款新的控制和读出系统（control and readout system,CRS）来操控微波脉冲的产生和信号的采集,提高了系统的集成度和可扩展性. 该谱仪可实现常规的连续波EPR（continuous-wave EPR,cw-EPR）、脉冲EPR（pulsed EPR）和瞬态EPR（transient EPR,trEPR）实验,并装配了6~300 K的无液氦变温装置,以及兼具平行模式与垂直模式的新型双模连续波谐振腔和用于脉冲EPR及trEPR的介质腔. 针对新型EPR谱仪和新谐振腔,本文利用双模连续波、脉冲和瞬态三个不同方式的EPR实验,对其功能进行了验证.     

Direct EPR detection of transient and continuous wave signals at 2.5 GHz

Direct detection of free induction decays and electron spin echoes, and the recording of echo-detected EPR spectra and electron spin echo envelope modulation patterns at a microwave frequency of 2.5 GHz is demonstrated. This corresponds to the measurement of the transverse magnetization in the laboratory frame, rather than in the rotating frame as usually done by down-converting the signal (homodyne detection). An oscilloscope with a 6-GHz analog bandwidth, a sampling rate of 20 GigaSamples per second, and a trigger frequency of 5 GHz for the edge trigger and 750 MHz for the advanced trigger, is used in these experiments. For signal averaging a 3-GHz microwave clock divider has been developed to synchronize the oscilloscope with the frequency of the EPR signal. Moreover, direct detection of continuous wave EPR signals at 2.5 GHz is described.     

On investigation of high Tc superconductors with Electron Paramagnetic Resonance spectrometers

Following the discovery of high T_c superconductors, many researchers have applied EPR spectrometers to investigate their properties using the regular instructions to operate the spectrometer. As no substantial information was obtained it was soon practically abandoned. Investigations performed recently with the EPR technique, using a different operating method than the conventional one and the introduction of a detailed theoretical study related to the interaction of the JV with the microwave magnetic field lead to new and important results related to properties of high anisotropy superconductors indicating that the EPR spectrometer can be used to investigate properties of high anisotropy superconductors. The failures when using conventional operating method to obtain meaningful results and the method used in the present work to carry out the measurements in a proper manner are presented. Some important results obtained in investigating high anisotropy superconductors by the EPR technique are presented.     

EPR dosimeter material properties of potassium tartrate hemihydrate

The ability of potassium tartrate hemihydrate as a radiation sensitive material for electron paramagnetic resonance (EPR) dosimetry was investigated. The samples were subjected to different doses, in the range of 1–9 Gy of ⁶⁰Co gamma rays at room temperature. The EPR spectra were investigated through variation of signal intensity with respect to absorbed dose, magnetic field modulation amplitude, microwave power and time stability. The results indicate that the sensitivity of potassium tartrate hemihydrate is about 30% higher than that of alanine. However, the EPR signal is timely less stable within the first two weeks after irradiation.     

Microwave frequency modulation in CW EPR at W-band using a loop-gap resonator

Loop-gap resonator (LGR) technology has been extended to W-band (94GHz). One output of a multiarm Q-band (35GHz) EPR bridge was translated to W-band for sample irradiation by mixing with 59 GHz; similarly, the EPR signal was translated back to Q-band for detection. A cavity resonant in the cylindrical TE011 mode suitable for use with 100 kHz field modulation has also been developed. Results using microwave frequency modulation (FM) at 50 kHz as an alternative to magnetic field modulation are described. FM was accomplished by modulating a varactor coupled to the 59 GHz oscillator. A spin-label study of sensitivity was performed under conditions of overmodulation and gamma2H1(2)T1T2<1. EPR spectra were obtained, both absorption and dispersion, by lock-in detection at the fundamental modulation frequency (50 kHz), and also at the second and third harmonics (100 and 150 kHz). Source noise was deleterious in first harmonic spectra, but was very low in second and third harmonic spectra. First harmonic microwave FM was transferred to microwave modulation at second and third harmonics by the spins, thus satisfying the "transfer of modulation" principle. The loaded Q-value of the LGR with sample was 90 (i.e., a bandwidth between 3 dB points of about 1 GHz), the resonator efficiency parameter was calculated to be 9.3 G at one W incident power, and the frequency deviation was 11.3 MHz p-p, which is equivalent to a field modulation amplitude of 4 G. W-band EPR using an LGR is a favorable configuration for microwave FM experiments.     

Development of a Resonator with Automatic Tuning and Coupling Capability to Minimize Sample Motion Noise for in Vivo EPR Spectroscopy

EPR spectroscopy has been applied to measure free radicals in vivo; however, respiratory, cardiac, and other movements of living animals are a major source of noise and spectral distortion. Sample motions result in changes in resonator frequency, Q, and coupling. These instabilities limit the applications that can be performed and the quality of data that can be obtained. Therefore, it is of great importance to develop resonators with automatic tuning and automatic coupling capability. We report the development of automatic tuning and automatic coupling provisions for a 750-MHz transversely oriented electric field reentrant resonator using two electronically tunable high Q hyperabrupt varactor diodes and feedback loops. In both moving phantoms and living mice, these automatic coupling control and automatic tuning control provisions resulted in an 8- to 10-fold increase in signal-to-noise ratio.     

Microwave absorption studies of MgB2 superconductor

Microwave absorption studies have been carried out on MgB₂ superconductor using a standard X-band EPR spectrometer. The modulated low-field microwave absorption signals recorded for polycrystalline (grain size ∼ 10 μm) samples suggested the absence of weak-link character. The field dependent direct microwave absorption has been found to obey a ✓H dependence with two different slopes, which indicated a transition from strongly pinned lattice to flux flow regime.     

Determination of T1-spin-lattice relaxation time in a two-level system by continuous wave multiquantum electron paramagnetic resonance spectroscopy in a presence of tetrachromatic microwave irradiation

Applicability of continuous wave multiquantum EPR methods to study relaxation times at X-band is examined. Multiquantum transitions excited in a two-level system by tetrachromatic irradiation are used for these studies. The Bloch equation model is applied to simulate lineshapes of the three quantum transitions as a function of frequency difference between exciting fields. The dependence of multiquantum transition signals on relaxation times and microwave amplitude is shown. On this basis a method of deducing relaxation times from these signals is formulated. The case of a homogeneously and inhomogeneously broadened resonance line is considered. Two experimental methods are used to verify the proposed hypothesis: the X-band continuous wave multiquantum EPR with four frequencies microwave field and saturation recovery EPR. The values of T₁ obtained from CW MQ EPR and SR EPR are compared.     

Reversible Photoisomerization of β-Methyl-β-Nitrostyrene: The Role of Triethylamine

The photolysis of trans-β-nitro-βmethylstyrene in acetonitrile solution gives the cisisomer with a quantum yield of 0.8. Addition of triethylamine to the system leads to a small decrease in the photoisomerization quantum yield and the appearance of a strong EPR signal. This signal remains for several hours at the end of the irradiation. It is demonstrated that the EPR signal is associated to an intermediary produced during the triethylamine catalyzed thermal back formation of the trans isomer. This intermediary bears an unpaired electron mostly associated to the nitro group and suggest that the thermal back reaction takes place by an initial electron transfer from the amine to the nitro group, leading to a long lived zwitterionic biradical.     

Use of the Frank sequence in pulsed EPR

The Frank polyphase sequence has been applied to pulsed EPR of triarylmethyl radicals at 25 6 MHz (9.1 mT magnetic field), using 256 phase pulses. In EPR, as in NMR, use of a Frank sequence of phase steps permits pulsed FID signal acquisition with very low power microwave/RF pulses (ca. 1.5 mW in the application reported here) relative to standard pulsed EPR. A 0.2 mM aqueous solution of a triarylmethyl radical was studied using a 16 mm diameter cross-loop resonator to isolate the EPR signal detection system from the incident pulses.