光纤化学传感技术研究近况

光纤化学传感器作为传感器的一个重要分支,结合了化学和光学的相关技术,将化学制膜、光纤技术以及化学分析中的分光光度法、拉曼光谱、荧光光谱、折射率检测等方法相融合,以其微型化,抗电磁干扰,传输信息量大,拥有自身参比等特点不断向前发展。简要综述了光纤化学传感技术研究近况和未来的发展趋势。重点对光纤pH化学传感器、光纤离子化学传感器和光纤气体化学传感器进行了介绍。简要分析了常见的敏感膜制备方法如化学键合法和溶胶凝胶(sol-gel)等方法。新型光纤——微结构光纤的出现为光纤化学传感器开辟了新的发展方向。由于其具有大的内表面积,结构设计灵活多样,光纤内部提供感应场所等特点,快速度成为光纤化学传感器的重要发展方向和研究热点。对微结构光纤衍生而来的新型光纤化学传感器进行了详细评述, 最后对光纤化学传感器的未来进行展望。     

一种用于变压器局部放电在线监测的光纤声发射传感器实验研究

提出了一种光纤声发射传感器并构建传感系统实现变压器局部放电在线监测,利用传感光栅体积小,重量轻,灵敏度高和抗电磁干扰的特点,将传感器置于变压器内部实现局部放电声发射信号的测量。研究了传感光栅实现声发射应力波测量的机理,声发射信号引起传感光栅反射光谱发生漂移,导致特定频点处反射光强发生变化,通过反射光强的变化实现声发射信号的测量。构建声发射传感系统实验模型并提出了一种系统性能优化策略,使系统工作在传感光栅反射光谱上升或下降沿的半峰值频点处,从而保障传感系统具有良好的线性输出特性;研究传感系统工作点稳定技术,设计信号反馈回路自动跟踪反射光谱的漂移,保证系统稳定工作在传感光栅半峰值频点处,消除温度变化对传感系统测量精度的影响。将封装好的传感器用于变压器局部放电现场检测,结果表明,光纤光栅声发射传感器与压电传感器相比具有灵敏度高、动态范围宽等优点,可以实现变压器局部放电在线监测。     

基于Mach-Zehnder干涉仪的单模光纤声波传感器的研究

光纤传感器是20世纪70年代中期发展起来的一种新型传感器.它与普通的传感器相比,具有灵敏度高、抗电磁干扰、耐腐蚀、防燃等优点,因此在温度、应力、磁场等传感领域都有着广泛的应用.本文研究的光纤声波传感器,其基础为Mach-Zehnder(M-Z)全光纤干涉仪,我们主要的工作集中在传感臂探头的制作.所研制的基于M-Z干涉仪...     

Fiber-optic, cantilever-type acoustic motion velocity hydrophone

The interaction between fluid loaded fiber-optic cantilevers and a low frequency acoustic wave is investigated as the basis for an acoustic vector sensor. The displacements of the prototype cantilevers are measured with an integrated fiber laser strain sensor. A theoretical model predicting the frequency dependent shape of acoustically driven planar and cylindrical fiber-optic cantilevers incorporating effects of fluid viscosity is presented. The model demonstrates good agreement with the measured response of two prototype cantilevers, characterized with a vibrating water column, in the regime of Re ≥ 1. The performance of each cantilever geometry is also analyzed. Factors affecting the sensor performance such as fluid viscosity, laser mode profile, and support motion are considered. The planar cantilever is shown to experience the largest acoustically induced force and hence the highest acoustic responsivity. However, the cylindrical cantilever exhibits the smoothest response in water, due to the influence of viscous fluid damping, and is capable of two axis particle velocity measurement. These cantilevers are shown to be capable of achieving acoustic resolutions approaching the lowest sea-state ocean noise.     

Development of One-dimensional Fiber-Optic Radiation Sensor for Measuring Dose Distributions of High Energy Photon Beams

The purpose of this study was to develop a method for measuring the one-dimensional dose distribution of a high-energy photon beam using a miniaturized high-resolution fiber-optic radiation sensor array. The measurements were made by thin plastic optical fibers with organic scintillating fiber sensor probes that emit the visible wavelength of light. The scintillating light is guided to a silicon photodiode array by plastic optical fibers in order to convert light output to an electrical signal. The one-dimensional spatial dependence of photon beam is measured by a one-dimensional fiberoptic sensor array in a poly(methyl methacrylate) (PMMA) phantom. It is shown that this fiber-optic radiation sensor has better spatial resolution than a conventional ionization chamber and much less time is required to measure one-dimensional dose distribution in the high radiation fields. The real-time and the high spatial resolution measurements due to the small detector volume make this system suitable for dosimetry in radiation therapy.     

二阶声低通滤波光纤水听器的声压灵敏度频响特性

信号混叠是基于光纤水听器的现代声纳系统走向应用必须解决的一个关键问题.初步的实验结果已经表明,声低通滤波光纤水听器是解决信号混叠问题的一种简单且行之有效的方案.基于电一声类比理论,建立了声低屯瞬ü庀怂鞯牡推导胁瘟磕Ｐ?利用电路分析的方法对其频响特性进行了研究.结果表明,这种光纤水听器系统与典型的二阶低通滤波电路具有相似的频响特性.为了验证理论分析的正确性,设计制作了一个简单的声低通滤波光纤水听器,并在驻波罐中对其声压灵敏度频响特性进行了测试,实验结果与数值计算的结果基本吻合.该光纤水听器低频响应非常平坦,声压灵敏度约为-141 dB,测量共振频率为985 Hz,与理论值1270 Hz基本一致.共振频率处的声压灵敏度为-126.8 dB,衰减速率约为20 dB/倍频程,3000 Hz以后的灵敏度衰减幅度大于20 dB.     

Fiber-optic pH sensor based on sol-gel film immobilized with neutral red

In this study, we developed a fiber-optic pH sensor based on a sol-gel film immobilized with neutral red (NR). A solgel film was prepared by mixing tetramethylorthosilicate (TMOS), trimethoxymethylsilane (MTMS), ethanol (EtOH), distilled water (H₂O), and NR powder. Accordingly, the thin pH sol-gel film was fabricated through a sol-gel process with a dip-coating method. The thickness and diameter of the fabricated pH sol-gel film are 0.11 and 0.6 mm, respectively. We measured the optical absorbance and the light intensity with the spectra of reflected light, which change with the color variation of the pH sol-gel film in the fiber-optic sensing probe. From the experimental results, we demonstrated that the proposed fiber-optic pH sensor has good reversibility, reproducibility, and a fast response time, in which the optical properties of the NR-based pH sol-gel film change with the pH value.     

Fiber-optic reflex sensor for in-line production measurement

The paper describes experiments concerning distance measurement with fiber-optic sensor and improvement of the measurement principle. The sensor probe was well-designed with a small structure and multi-function. The novel optical fiber probe arrangement as well as the possibilities of use for complex measurement problems are explained using the measurement of an internal screw thread as an example. The experimental results show that the measurement uncertainty of the thread minor diameter can reach ±10 μm, and the stability of the measurement system is better than 0.07%.     

A fiber-optic voltage sensor based on macrobending structure

We propose and demonstrate an optical voltage sensing scheme based on a macrobending optical fiber in a ratiometric power measurement system. This novel approach to sensing has not been utilized before and has the advantage that the sensor involves simple fabrication compared to existing fiber-optic voltage sensors. To prove the feasibility of such a fiber-optic sensor, a sensor for a voltage range from 0∼100 V is demonstrated, with a resolution of 0.5 V. The sensor is robust, linear, and shows a competitive measurement resolution. The sensor can be easily scaled to suit other voltage levels and be effectively combined with optical current sensors.     

一种高稳定、高分辨率的光纤位移检测系统

介绍一种大量程、高分辨率、高稳定的光纤传感位移测量系统。该系统基于反射式强度调制机制,由光发射机、传感器、光接收机三部分组成。系统通过采用调制、解调、窄带滤波,信号支路和参考支路双通道相比测量等技术措施,来保证系统的高稳定性和高分辨率。实验还表明测量中应尽量使用朗伯特平面作为光反射面,以解决二次安装的重复性问题。     

Stabilized fiber-optic extrinsic Fabry–Perot sensor system for acoustic emission measurement

A fiber-optic Fabry–Perot (F–P) acoustic emission (AE) sensor system based on an improved double wavelength stabilization technique is described. Without stabilization, the sensor system drifts out of quadrature due to the presence of low-frequency dynamic strains. The stabilization is achieved by using a dense wavelength division multiplexer (DWDM) to generate two quadrature phase-shifted output signals. An optimum model of double wavelength stabilization is established. The filtering wavelengths of DWDM are calculated using an optimization design method. The performance of the developed sensor system was verified by two preliminary tests. One was a test on the stabilization of operating point of fiber-optic F–P sensor, and other was the detection of simulated AE signals generated by the impact and pencil lead breaking. The test results demonstrate that simulated AE signals are successfully detected using this stabilized sensor system, which solves the fade-out problem.     

Fabrication and comparison of thermochromic material-based fiber-optic sensors for monitoring the temperature of water

In this study, we explored the feasibility of developing two types of fiber-optic temperature sensors that can measure the temperature of water. One uses a thermochromic material such as Lophine, whose optical absorbance changes according to the thermal variation. The other uses a thermochromic pigment that gradually loses its own color through heat absorption. We measured the change in the intensity of the reflected light, which was due to the variation of the optical property of Lophine and pigments, with thermal variation. The relationship between the temperature of water and the output signal of the fiber-optic sensors was also determined. The fiber-optic temperature sensor using Lophine provided a relatively broad range of temperature measurement with low sensitivity, whereas the fiber-optic temperature sensor using a thermochromic pigment offered a high sensitivity in a narrow range of temperature measurement.     

一种确定光纤传感器中3×3耦合器输出信号相位差的新算法

本文提出了一种基于Bessel函数展开,在频域内精确确定光纤传感器3×3耦合器输出信号相位差的算法。在Mach-Zehnder干涉仪原理的基础上,通过建立3~3耦合器输出信号的数学模型和利用耦合器输出光功率的Bessel展开,完成了算法的理论推导,并且在实验室中进行了声学实验。数据处理结果表明,该算法能够较精确地确定3×3耦合器输出信号的相位差,且相位差与调制频率无关,与理论相符。     

Low-Temperature Radiometric Measurements Using a Silver Halide Optical Fiber and Infrared Optical Devices

In this study, we measured an infrared radiation which is transferred by a silver halide optical fiber from a heat source using a radiometer system for low-temperature measurements. To increase the amount of infrared radiation through the silver halide optical fiber and to the pyroelectric sensor, infrared optical devices used were an infrared focusing lens and a collimator. The relationship between the temperatures of a heat source and the measured radiometer signals were determined. The measurable temperature range of a fiber-optic temperature sensor using a pyroelectric sensor was from 298 to 333 K. It is expected that a noncontact low-temperature sensor using an infrared optical fiber can be developed for medical and industrial usages based on the results of this study.     

Quasi-distributed strain sensing with white-light interferometry: a novel approach

An optical fiber ring is used to generate multiple reference waves in a multiplexed fiber-optic Michelson-type sensor array. The array consists of N sensing segments connected in series along a single optical fiber path and is interrogated with a white-light interferometric technique. Experimental results with a two-sensor array are presented.     

光纤菲佐传感器频分复用网络解调方法研究

为了减小光纤菲佐传感器间的串扰,提高传感器网络的复用能力,提出了基于Pisarenko正弦波恢复法的光纤菲佐应变传感器频分复用网络光谱解调方案。在多光束干涉原理的基础上,建立了基于Pisarenko正弦波恢复方法的传感器频分复用解调模型,并对2个光纤菲佐传感器的串扰进行了实验研究。快速傅里叶变换能够达到应变精度好于±10με的传感器间最小腔长差约为500μm,而该方法可以把最小腔长差缩短至100μm左右。这意味着系统的复用能力提高了大约5倍。因此,该方法是一种串扰小、复用能力强的解调方法,在大容量准分布式传感网络中具有极大的潜在应用价值。     

Study of fiber-optic current sensing based on degree of polarization measurement

A novel fiber-optic current sensing scheme is proposed by converting the Faraday rotation to the optical signal's degree of polarization (DOP) change. In this scheme, the lightwave passes through a fiber resonant cavity multiply and experiences Faraday rotation simultaneously. Its main merit is immunity from the environment disturbance to the fiber used in ordinary Faraday rotation sensor. Brief theoretical analysis and simulation are given to show its basic characteristics. Experimental results are demonstrated and the feasibility of the proposed method is also shown.     

光纤Fizeau干涉仪的声发射检测研究

验证了一种基于光纤Fizeau干涉仪的声发射传感器,可用于固体表面传播的超声波的检测.这种传感器的特点是能够精确地检测由固体表面传播的超声波产生的微弱振动.当超声波信号通过光纤传感器到达探测器时,干涉仪的输出光强度受到了超声信号的调制.通过检测干涉仪的输出光强度并利用Fourier变换,测得了超声信号的振幅和频率.对传感系统的相位调制特性进行了仿真,并对实验结果进行了分析.     

Fundamental Properties of 10 Gbit/s Coherent Optical Code Division Multiplexing: Experiment

Coherent optical code division multiplexing is a novel method using the phase of optical pulse as the bipolar code for future fiber-optic communication networks. Some optical bipolar codes with a repetition frequency over 10 GHz are generated experimentally and their fundamental properties are elucidated. The key features of the method, auto- and cross-correlation of these codes, are shown experimentally and compared with the theoretical results. Interference between two optical narrow pulses with high repetition frequency is investigated experimentally under various conditions of optical phase and wavelength as the basis of the method. A guaranty of realization of the technique is shown.     

四阶声低通滤波光纤水听器的声压灵敏度频响特性

对四阶声低通滤波光纤水听器的声压灵敏度频响特性进行了详细的理论和实验研究.在已有的低频集中参量模型中引入了一个机械声阻,用于描述系统的机械损耗,从而得到了改进的声学等效电路.相位频响特性对于光纤水听器的阵列应用非常重要,关系到阵列的波束形成效果,进而影响系统定位、识别与跟踪目标的能力,因此在分析幅度频响特性的同时研究了相位频响特性.仿真分析了各主要参量对声压传递函数的影响,得到了一些对声低通滤波光纤水听器设计具有重要指导意义的结论.实测声压灵敏度频响曲线与仿真结果基本一致,较好地验证了理论分析的正确性.四 关键词： 光纤传感器 光纤水听器 声压灵敏度 低通滤波器