2-甲氨基-5-(2-芳氧吡啶-3-基)-1,3,4-噻二唑类化合物的合成与荧光性质研究

设计合成了一系列未见文献报道的2-甲氨基-5-(2-芳氧吡啶-3-基)-1,3,4-噻二唑衍生物,其结构均经过1HNMR,IR和元素分析表征.测定了其荧光性能,结果显示此类化合物具有较好的荧光性,其荧光发射波长在384～390nm范围,最大荧光量子产率为0.12.     

新型荧光试剂N-9-吖啶-α-氨基酸的合成及表征

新型荧光试剂N-9-吖啶-α-氨基酸的合成及表征;荧光试剂; N-吖啶-α-氨基酸; 合成;表征     

新荧光试剂5-(4′-氯-2′-羧基苯基偶氮)-4-氧代-2-硫代四氢噻唑的合成及分析应用研究

本文报道了新荧光试剂5-(4’-氯-2’-羧基苯基偶氮)-4-氧代-2-硫代四氢噻唑(CC-POST)的合成及其荧光分析应用。确证了其结构。在pH=5.0～5.4时。它与铜(Ⅱ)形成荧光螯合物。λ_(ex)/λ_(em)=310mn/408nm,检测限为0.5ng/g。用此法测定了茶叶中的痕量铜,结果满意。     

3-对甲苯基-5-(4′-硝基-2′-羧基苯偶氮)-2-硫代-4-噻唑啉酮的合成及用于铜的荧光光度测定

本文报道了新荧光试剂3-对甲苯基-5-（4’-硝基-2‘-羧基苯偶氮）-2-硫代-4-噻唑啉酮（MPNCPATTN）的合成。通过元素分析、红外光谱，核磁共振氢谱和质谱确证了其结构。在pH5．6时，它与铜（Ⅱ）形成稳定的荧光络合物，在λex／λem=308nm／403nm处产生强烈荧光，其荧光强度与铜（Ⅱ）的浓度在6．28×10－9～9．44×10-7mo1／L范围内呈线性关系，检测限为0.399μg／L的铜（Ⅱ）。测定了人发中的痕量铜，结果满意。     

6-氨基-5-氰基-3-甲基-4-(3-硝基苯)-1-苯基吡唑[3,4-b]并吡啶与人血清白蛋白结合作用的光谱特征

采用紫外光谱法和荧光光谱法研究了6-氨基-5-氰基-3-甲基-4-(3-硝基苯)-1-苯基吡唑[3,4-b]并吡啶(6A)与人血清白蛋白(HSA)的结合作用,利用同步荧光法和三维荧光法研究了6A与HSA作用前后人血清白蛋白的构象变化。观测到生理pH7.4条件下6A使HSA的紫外吸收峰增强,特征荧光峰猝灭。Stern-Volmer曲线显示,6A对HSA的荧光猝灭可能是一个单一的静态猝灭过程,并且得出18℃和37℃时的结合位点数和结合常数。根据F rster非辐射转移理论可求出6A与HSA作用距离r=3.73 nm;根据基本热力学参数ΔH、ΔS和ΔG判断6A和HSA主要通过氢键和范德华力发生相互作用。     

果糖-6-磷酸-2-激酶的色氨酸残基的研究

NBS滴定PFK-2的紫外光谱的结果表明,该酶可滴定Trp残基数为4个其中2个是活性必需的。 用295nm的紫外光激发果糖-6-磷酸-2-激酶(PFK-2),在335nm附近有较强的发射荧光。该荧光能较专一反映PFK-2的Trp基团的状态。底物果糖-6-磷酸对该荧光不影响,ATP引起荧光吸灭。最大吸灭幅度为30％左右。 采用荧光滴定方法测定ATP与酶的结合,得出解离常数(K_i)在低浓度ATP时为0.033mmol/L,高度时为0.23mmol/L。表明该结合具有负协同性。Mg~(2+)、无机磷均降低ATP与酶的K_i值而表现为激活因子;果糖-6-磷酸和果糖-2,6-二磷酸酸对K_i值不影响。ATP结合后引起了该酶构象上的较大的变化。 在ATP保护下,PFK-2对NBS的失活速度稍有增加。丙烯酰胺荧光滴定的结果是,在有无ATP时的Stern-Volmer常数(K_(SV))皆为4.0。     

基于2，3-萘-18-冠-6单元的共轭高分子对金属离子的荧光传感器

能发射蓝绿色荧光的共轭高分子由单体1,4-二溴-2,3-萘-18-冠-6(M-2)与1,4-二乙烯基-2,5-二丁氧基苯(M-3)通过Pd催化的Heck偶联反应合成制得。通过荧光和紫外-可见光谱探讨了高分子对金属离子的响应性质,其中Hg²⁺能使高分子荧光淬灭、吸收增强,但As^Ⅲ、Pb²⁺和K⁺对高分子的荧光光谱改变很小。结果表明以2,3-萘-18-冠-6作为荧光团和识别位点的共轭高分子可作为有效识别Hg²⁺的荧光化学传感器。     

4-[2-(二甲氨基)乙氧基]-N-十八烷基-1,8-萘酰亚胺荧光染料的合成及其性能研究

以4-溴-1,8-萘酐为原料,合成脂溶性4-[2-(二甲氨基)乙氧基]-N-十八烷基-1,8-萘酰亚胺。对其进行了1H NMR和IR表征。考察了荧光染料在DMF、乙腈、丙酮、乙酸乙酯和乙醚5种溶剂中的荧光光谱和吸收光谱,发现由于溶剂效应,随溶剂极性由小到大,荧光光谱和吸收光谱的最大峰值波长逐渐红移。考察了不同金属离子和pH对荧光染料荧光光谱的影响,结果表明荧光强度随Fe3+、Zn2+、Co2+浓度增大而逐渐增强,Fe3+的影响最为显著;当pH<7时,荧光强度随着pH的降低逐渐增强;进一步考察了Fe3+、Zn2+、Co2+对吸收光谱的影响,结果发现吸收光谱均蓝移。分析认为荧光染料的光致电子转移被阻碍,实验结果表明,合成的新型荧光染料可用于溶液中金属离子和pH的检测。     

新型荧光试剂1-(8-喹啉)-3-(3,5-二溴-2-吡啶)-三氮烯的合成及其应用

将具有荧光特性的杂环8-氨基喹啉和吡啶类试剂结合,并引入三氮烯结构,合成了新型荧光试剂1-(8-喹啉)-3-(3,5-二溴-2-吡啶)-三氮烯(QBPyT)。其结构经元素分析、红外光谱、核磁共振波谱证实。研究结果表明,在pH 9.5硼酸-氢氧化钠缓冲溶液的介质存在下,该试剂在λex/λem=248nm/496nm处产生强荧光,并且能与铅(Ⅱ)形成配合物从而使荧光增强。据此建立了三氮烯测定铅(Ⅱ)的新型荧光分析法。铅的浓度在5.0×10-7～1.2×10-5 mol.L范围内与其荧光强度呈线性关系,检出限(3S/N)为9.5×10-8 mol.L。将其应用于水样中铅(Ⅱ)的测定,测得回收率在92.6%～94.0%之间,测定值的相对标准偏差(n=5)小于3.5%。     

衍生于苯并-12-冠-4的双光子荧光Fe3+探针

合成了双光子荧光探针2,5-二氰基-1,4-二[2′-(4′-苯并-12-冠-4)乙烯基]苯(1),并进行了红外、质谱及元素分析。探针1在单、双光子荧光发射中对金属离子显示了相似的选择性,双光子过程中的选择性略优于单光子过程,并对Fe3+显示出高度选择性识别。探针1对Fe3+的单、双光子荧光强度随Fe3+浓度的升高而急剧降低;单、双光子荧光滴定过程中探针对Fe3+的络合常数分别是:5.70±0.03(logK11)与4.74±0.05(logK12)、5.76±0.04(logK11)与4.81±0.07(logK12)。探针1的双光子吸收截面(δTPA)随溶剂极性增加而减小,在甲苯与乙腈中的δTPA分别是2198,1125GM,探针与Fe3+络合后其双光子吸收截面显著减小。研究结果表明,化合物1可以作为Fe3+探针应用到单光子激发荧光与双光子激发荧光检测;可以用开发单光子荧光探针的策略来设计应用于生物成像的双光子荧光探针。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。