Adsorption of O, H, OH, and H2O on Ag(100)

The adsorption of H(2)O and its dissociation products, O, H, and OH, on Ag(100) has been studied using an ab initio embedding method. Results at different sites (atop, bridge, and hollow) are presented. The four-fold hollow site is found to be the most stable adsorption site for O, H, and OH, and the calculated adsorption energies are 87.1, 42.7, and 76.2 kcal mol(-1), respectively. The adsorption energy of water at the atop and bridge sites is almost identical with values of 11.1 and 12.0 kcal mol(-1), respectively. The formation of adsorbed OH species by adsorption of water on oxygen-precovered Ag(100) is predicted to be exothermic by 36 kcal mol(-1).     

Low temperature H2O and NO2 coadsorption on theta-Al2O3/NiAl(100) ultrathin films

The coadsorption of H(2)O and NO(2) molecules on a well-ordered, ultrathin theta-Al(2)O(3)/NiAl(100) film surface was studied using temperature programmed desorption (TPD), infrared reflection absorption spectroscopy (IRAS), and X-ray photoelectron spectroscopy (XPS). For H(2)O and NO(2) monolayers adsorbed separately on the theta-Al(2)O(3)/NiAl(100) surface, adsorption energies were estimated to be 44.8 and 36.6 kJ/mol, respectively. Coadsorption systems prepared by sequential deposition of NO(2) and H(2)O revealed the existence of coverage and temperature-dependent adsorption regimes where H(2)O molecules and the surface NO(x) species (NO(2)/N(2)O(4)/NO(2)(-),NO(3)(-)) form segregated and/or mixed domains. Influence of the changes in the crystallinity of solid water (amorphous vs crystalline) on the coadsorption properties of the NO(2)/H(2)O/theta-Al(2)O(3)/NiAl(100) system is also discussed.     

A DFT study of H2O dissociation on metal‐precovered Fe (100) surface

The H₂O adsorption and dissociation on the Fe (100) surface with different precovered metals are studied by density functional theory. On both kinds of metal‐precovered surface, H₂O molecules prefer adsorb on hollow sites than bridge and top sites. The impurity energy difference is proportional to the adsorption energy, but the adsorbates are not sensitive to the adsorption orientation and height relative to the surface. The Hirshfeld charge analysis shows that water molecules act as an electron donor while the surface Fe atoms act as an electron acceptor. The rotation and dissociation of H₂O molecule occur on the Co‐ and Mn‐precovered surfaces. Some H₂O molecules are dissociated into OH and H groups. The energy barriers are about 0.5 to 1.0 eV, whose are consistence with the experimental data. H₂O molecules can be dissociated more easily at the top site on Co‐precovered surface 1 than that at bridge site on Mn‐precovered surface 2 because of the lower reaction barrier. The dispersion correction effects on the energies and adsorption configurations on Co‐precovered surface 1 were calculated by OBS + PW91. The dispersion contributions can improve a bit of the bond energy of adsorbates and weaken the hydrogen bond effect between adsorption molecules a little.     

Enhanced selectivity towards O(2) and H(2) dissociation on ultrathin Cu films on Ru(0001)

The reactivity of Cu monolayer (ML) and bilayer films grown on Ru(0001) towards O(2) and H(2) has been investigated. O(2) initial sticking coefficients were determined using the King and Wells method in the incident energy range 40-450 meV, and compared to the corresponding values measured on clean Ru(0001) and Cu(111) surfaces. A relative large O(2) sticking coefficient (～0.5-0.8) was measured for 1 ML Cu and even 2 ML Cu/Ru(0001). At low incident energies, this is one order of magnitude larger than the value observed on Cu(111). In contrast, the corresponding reactivity to H(2) was near zero on both Cu monolayer and bilayer films, for incident energies up to 175 meV. Water adsorption on 2 ML Cu/Ru(0001) was found to behave quite differently than on the Ru(0001) and Cu(111) surfaces. Our study shows that Cu/Ru(0001) is a highly selective system, which presents a quite different chemical reactivity towards different species in the same range of collision energies.     

NO双分子在Cu2O(111)面吸附与解离的理论研究

采用广义梯度密度泛函理论结合周期平板模型方法, 在DNP基组下, 研究了NO双分子在三重态和单重态两种电子组态下在Cu2O(111)完整表面的吸附情况. 考虑了Cu+(NO)(NO)、Cu+(NO)(ON)及Cu+(ON)(ON)这三种构型, 计算了它们的吸附能和Mulliken电荷, 分析并预测了吸附后可能产生的物种. 结果表明, 当两个NO分子都以O端吸附在Cu2O(111)表面时即Cu+(ON)(ON)构型, N—N键长很短, 只有124.4 pm, 吸附的两个NO分子形成了二聚体形式, 这种吸附构型有利于进一步离解产生N2或N2O并形成Cu-O表面物种.     

Sonochemical Preparation of Micro-and Nanometer Cu2O

Cu2O particles with different morphologies and scales were prepared sonochemically on the solid-liquid interface of CuCl and water, by adjusting the reaction factors. The products were characterized by powder X-ray diffraction(XRD) and scanning electron microscopy(SEM). The formation and morphology of Cu2O crystals were influenced by high-intensity ultrasound,reaction temperature,and addition of CuCl.The results indicate that micrometer Cu2O was crystallized in cubic and octahedral shapes, whereas, nanometer Cu2O was not produced in well-shaped crystals.     

Co9S8 as a catalyst for electroreduction of O2: quantum chemistry predictions

The slab band quantum computational approach in the Vienna ab initio simulation package (VASP) is used to calculate the adsorption energies of reactants, reaction intermediates, and products in O2 reduction and in water oxidation in acid on three crystallographic surfaces of pentlandite structure Co9S8. Reversible potentials for the reaction steps involving electron and proton transfer are determined by using the energies in a linear Gibbs free energy relationship. On the basis of these results, we find that the partially OH-covered (202) surface is active toward O2 reduction and should have overpotential behavior similar to that observed for platinum electrodes. One structure in the predicted four-electron reduction mechanism is novel: S2- provides an adsorption site for O following O-O bond scission, which, unlike the case of platinum electrodes, takes place prior to the first reduction step.     

K_2O助剂对合成碳酸二甲酯用Cu-Ni/MoO_3-SiO_2催化剂吸附和反应性能的影响

用等体积浸渍法制备了MoO3 SiO2 (MoSiO)表面复合氧化物负载的Cu Ni K2 O催化剂。利用IR ,TPR ,TPD以及微反技术研究了K2 O助剂对CO2 和CH3OH在Cu Ni MoSiO催化剂表面上吸附和合成DMC(碳酸二甲酯 )反应性能的影响。结果表明 :K2 O助剂的加入 ,使CO2 在催化剂表面吸附强度增加 ,当K2 O含量达Cu Ni总量的 15 %时 ,CO2 在催化剂表面上吸附后生成K2 CO3;CH3OH在催化剂表面上的解离吸附态 (CH3O- H )的吸附强度减弱 ;CO2 和CH3OH在Cu Ni K2 O MoSiO催化剂表面反应主要产物为DMC ,H2 O ,CO和CH2 O。随着K2 O助剂的加入 ,反应转化率在 10 %之前增加 ,之后下降 ,DMC选择性稍有提高。副产物 (CO和CH2 O)的选择性下降。根据实验结果探讨了K2 O对催化剂表面活性中心的电荷分布的影响。     

Hydrogen Generation by Splitting H_2O Molecule on the Pt_6Cu Cluster

Seven reaction paths for hydrogen generation from water molecule with Pt_6Cu cluster are identified, based on the density functional theory with exchange-correlation functional in Becke's three-parameter form. The complex structures of the reactant H_2O@Pt_6Cu and the structures of the products H2+O@Pt6Cu and H+OH@Pt6Cu on various adsorption sites of Pt_6Cu cluster are optimized and the energy stability of the structures is confirmed by frequency analysis. The geometries of the transition states and the intrinsic reaction coordinate are also determined at the same theoretical level. The energy barrier for each reaction is calculated. The results demonstrate that the Pt_6Cu cluster can abstract one H atom from H_2O molecule with one step reaction by overcoming a moderate energy barrier. These findings can be helpful for understanding the mechanism to produce hydrogen from a water molecule with Pt_6Cu cluster.     

TiO2(110)面的弛豫结构及吸附O2的密度泛函研究

采用DFT/B3LYP方法研究了TiO2 ( 110 )的完整和氧缺陷表面的弛豫构型 ,并对O2 在氧缺陷表面的三种可能吸附构型进行了优化 ,计算了它们的吸附能、振动频率和重叠布居 .分析并预测了吸附后可能产生的物种 .本文的计算结果与XPS ,TPD和ELS等实验吻合     

二氧化碳和丙烯在Cu2(OEt)2/SiO2催化下超临界合成甲基丙烯酸

负载型双核金属乙氧基配合物催化剂Cu2(OEt)2／SiO2采用表面改性法制备。运用滴定、IR、DSC和超临界反应技术对催化剂的表面结构、化学吸附性质和反应性能进行了研究。结果表明：负载型双核金属乙氧基配合物Cu2(OEt)2／SiO2中Cu”与载体SiO2表面O^2-以双齿配位形式键合,存在Cu2(OEt)2双核结构;二氧化碳在催化剂表面吸附形式形成桥式和乙氧碳酸酯基物种两种吸附态,丙烯则只有一种分子吸附态;在超临界的反应条件下,二氧化碳和丙烯在Cu2(OEt)2／SiO2催化剂上可以高选择性地合成甲基丙烯酸;反应物分子共吸附于催化剂表面,同一活性基元以及羧酸根与丙烯解离吸附态的形成是反应顺利进行的关键因素。     

A DFT Study of CO Adsorption on the Cu2O（111） Surface with Oxygen Vacancy

First-principles calculations based on density functional theory （DFr） and the generalized gradient approximation （GGA） have been used to study the adsorption of CO molecule on the Cu2O（111） oxygen-vacancy surface. Calculations indicate that the C-O bond is weakened upon adsorption compared with that over perfect surface. In addition, with the density increase of the defective sites, the adsorption energies of the defect-CO configuration increase whereas the C-O bond nearly remains constant.     

Shape evolution and size-controllable synthesis of Cu2O octahedra and their morphology-dependent photocatalytic properties

Octahedral Cu(2)O crystals with tunable edge length were synthesized by reducing copper hydroxide with hydrazine without using any surfactant. Systematic experiments were carried out to investigate the factors which impact on the morphology and size of the products. The molar ratios of the reagents (NH(3):Cu(2+) and OH(-):Cu(2+)) determined the morphology and size of the corresponding products via affecting the coordination between NH(3) and Cu(2+). It is demonstrated that the ratio of growth rate along 111 versus 100 was varied by adjusting the molar ratio of NH(3) to Cu(2+), thus Cu(2)O crystals with different morphologies such as spheres, cubelike, and octahedra were obtained. The edge lengths of octahedra can be easily tuned from 130 to 600 nm by adjusting the molar ratio of OH(-) to Cu(2+). It is an effective and facile method for the controlled synthesis of octahedral Cu(2)O. The obtained octahedral Cu(2)O particles show improved ability on adsorption and photodegradation of methyl orange compared with cubic Cu(2)O particles.     

Computational investigation of O2 reduction and diffusion on 25% Sr-doped LaMnO3 cathodes in solid oxide fuel cells

The oxygen reduction reaction (ORR) and diffusion mechanisms on 25% Sr-doped LaMnO(3) (LSM) cathode materials as well as their kinetic behavior have been studied by using spin-polarized density functional theory (DFT) calculations. Bader charge and frequency analyses were carried out to identify the oxidation state of adsorbed oxygen species. DFT and molecular dynamics (MD) results show that the fast O(2) adsorption/reduction process via superoxide and peroxide intermediates is energetically favorable on the Mn site rather than on the Sr site. Furthermore, the higher adsorption energies on the Mn site of the (110) surface compared to those on the (100) surface imply that the former is more efficient for O(2) reduction. Significantly, we predict that oxygen vacancies enhance O(2) reduction kinetics and that the O-ion migration through the bulk is dominant over that on the surface of the LSM cathode.     

Ozone-water 1:1 complexes O3-H2O: an ab initio study

Ab initio MO calculations have been carried out for the ozone-water 1:1 complexes in order to elucidate the structures and electronic state of the complexes. The QCISD calculations indicated that three structures are obtained as stable forms of O(3)-H(2)O. The most stable structure of O(3)-H(2)O has C(s) symmetry where the central oxygen of O(3) and all atoms of H(2)O are located on the molecular C(s) plane. The dipole of H(2)O orients toward the central oxygen atom of O(3) (i.e., dipole orientation form). The other two forms are cis and trans forms of O(3)-H(2)O where all atoms are located on the molecular plane, and a hydrogen of H(2)O binds to one of the terminal oxygen atoms of O(3) by a hydrogen bond. The binding energies of O(3) to H(2)O for dipole, cis, and trans forms are calculated to be 2.39, 2.27, and 2.30 kcal/mol, respectively, at the QCISD(T)/6-311++G(3df,3pd)//QCISD/6-311++G((d,p) level. The dipole orientation form is more stable in energy than the cis and trans forms. Rotational constants for the dipole orientation form are calculated to be A = 11.897, B = 4.177, and C = 3.318 GHz which are in good agreement with the experimental values (A = 11.961, B = 4.174, and C = 3.265 GHz). The electronic states of O(3)-H(2)O were discussed on the basis of theoretical results.     

CO和CH3O在Cu2O(111)表面吸附特性及共吸附的理论研究

基于密度泛函理论, 采用广义梯度近似方法结合周期平板模型, 对Cu₂O(111)非极性表面上CO和CH₃O的吸附和共吸附进行了系统的研究. 计算了CO以4种吸附模式和CH₃O以O端在Cu₂O(111)表面上的吸附, 通过对不同吸附位置的吸附能、几何构型参数和Mulliken电荷的计算和比较发现, Cu₂O(111)表面上配位未饱和铜离子(Cu_CUS)为CO的活性吸附位; 配位饱和铜离子(Cu_CSA)为CH₃O的活性吸附位. CO和CH₃O吸附于Cu₂O(111)表面后, 表面弛豫现象明显改善. CO和CH₃O与Cu₂O(111)表面能够形成共吸附体系, CO和CH₃O之间的相互作用力达到75.89 kJ/mol, 为典型的化学作用, 有助于促进CO和CH₃O反应形成表面物种CH₃OCO, 计算结果与实验事实一致.     

Properties of ternary insulating systems: the electronic structure of MgSO4.H2O

Structural and electronic properties of (100)-oriented MgSO(4) and MgSO(4).H(2)O surfaces and the adsorption of water on the latter were investigated theoretically with a combination of ab initio and semiempirical methods. Ab initio electronic structure calculations were based on a density functional theory (DFT)-Hartree-Fock (HF) hybrid approach. The semiempirical method MSINDO was used for the determination of the local adsorption geometry of the water molecule. With the hybrid method good agreement was obtained with the experimental band gap of 7.4 eV determined with electron energy loss spectroscopy of polycrystalline MgSO(4).H(2)O samples under ultrahigh vacuum conditions. The valence bands of the (100) surfaces of both MgSO(4) and MgSO(4).H(2)O are formed mainly by the O2p levels, whereas the S2p states contribute to the lower part of the conduction band. The preferred adsorption site of water at MgSO(4).H(2)O (100) is above a surface Mg atom. The water molecule is stabilized by two additional hydrogen bonds with surface atoms. Only small differences between the electronic structure of MgSO(4).H(2)O and MgSO(4) were observed. Also, the molecular adsorption of water on the MgSO(4).H(2)O surface leads to only small shifts of the electronic energy levels.     

水煤气变换反应的微观动力学分析──Cu基催化剂上H_2S中毒失活原因的 Monte Carlo 模拟研究

用ＢＯＣＭＰ方法及ＭｏｎｔｅＣａｒｌｏ模拟技术，对Ｈ２Ｓ导致Ｃｕ基催化剂失活的原因进行了计算分析。研究结果表明，当原料气中存在Ｈ２Ｓ时，ＷＧＳ反应的活化能明显高于无Ｈ２Ｓ时的活化能，随着表面Ｈ２Ｓ浓度的增大（θ＝０，０．１０，０．２５），反应的活化能也逐渐变大（其大小比为１∶１．３４∶３．３），究其原因可归结为Ｈ２Ｓ的存在使得反应物分子的吸附热减小，从而使Ｈ２Ｏ的解离吸附（ＷＧＳ反应的速控步骤）活化能增大。     

DFT Simulations of Water Adsorption and Activation on Low‐Index α‐Ga2O3 Surfaces

Density functional theory (DFT) calculations are used to explore water adsorption and activation on different α‐Ga₂O₃ surfaces, namely (001), (100), (110), and (012). The geometries and binding energies of molecular and dissociative adsorption are studied as a function of coverage. The simulations reveal that dissociative water adsorption on all the studied low‐index surfaces are thermodynamically favorable. Analysis of surface energies suggests that the most preferentially exposed surface is (012). The contribution of surface relaxation to the respective surface energies is significant. Calculations of electron local density of states indicate that the electron‐energy band gaps for the four investigated surfaces appears to be less related to the difference in coordinative unsaturation of the surface atoms, but rather to changes in the ionicity of the surface chemical bonds. The electrochemical computation is used to investigate the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) on α‐Ga₂O₃ surfaces. Our results indicate that the (100) and (110) surfaces, which have low stability, are the most favorable ones for HER and OER, respectively.     

Selective growth of Au nanoparticles on (111) facets of Cu2O microcrystals with an enhanced electrocatalytic property

The selective growth of Au nanoparticles on (111) facets of truncated octahedral and cuboctahedral Cu(2)O crystals has been achieved by exploiting the differences in the standard potential between AuCl(4)(-)/Au and Cu(2+)/Cu(2)O pairs and in surface energies between (111) and (100) planes. The density and size of Au nanoparticles can be controlled by tuning the concentration of the gold precursor. Truncated octahedral Cu(2)O-Au nanocomposites have a 10 times higher electrochemically catalytic activity toward H(2)O(2) reduction than do pure Cu(2)O crystals. The enhanced catalysis may be derived from the polarization of Au NPs at the interface, which makes Cu(2)O more active for H(2)O(2) reduction.