于离子液体和介孔SBA-15为支架的准固态染料敏化太阳能电池

利用介孔SBA-15作为支架材料制备了一类准固态电解质。离子电导测试表明SBA-15的引入增加了准固态电解质的电导率。通过拉曼光谱证实了聚碘离子I₃^-和I₅ ^-的存在，并且通过计算表明聚碘离子的扩散系数是I^-的两倍。经过组装优化，基于该准固态电解质的电池在AM1.5，75 mW cm^-2的光强下可得到4.3%的光电转化效率。     

吲哚方酸菁半导体在场效应晶体管中的应用

研究了2,3,3-三甲基-1-H-吲哚方酸菁的场效应性质, 通过X射线衍射证实了方酸菁分子内电荷分离结构以及分子间面面堆积模式, 并在Si/SiO₂基片上通过真空蒸镀和旋涂的方法制备了p型晶体管器件. 通过对器件性能与沟道形态的研究, 我们发现退火处理能促进方酸菁薄膜由无定形态向多晶态转变, 从而使薄膜晶体管的迁移率从10^-5 cm²?V^-1?s^-1量级提高到10^-3 cm²?V^-1?s^-1量级. 顶接触结构单晶器件获得了7.8×10^-2 cm²?V^-1?s^-1的迁移率. 未封装的方酸菁晶体管在大气中也表现出较好的稳定性.     

尿素作为造孔剂对聚乙烯支撑的PAMS聚合物电解质性能的改进

采用乳液聚合法合成聚(丙烯腈-甲基丙烯酸甲酯-苯乙烯) (P(AN-MMA-ST)或者共聚物PAMS), 并利用尿素作为造孔剂制备了聚乙烯(PE)支撑的PAMS聚合物膜(PE-PAMS-U)及凝胶聚合物电解质(GPE). 利用傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)、扫描电子显微镜(SEM)、热重(TG)分析、线性电位扫描(LSV)、电化学阻抗谱(EIS)以及充放电等方法对PAMS聚合物以及PE支撑的聚(丙烯腈-甲基丙烯酸甲酯-苯乙烯) (PE-PAMS)聚合物隔膜及凝胶聚合物电解质的性能进行了研究. 结果表明, 利用尿素作为造孔剂可以提高PE-PAMS凝胶聚合物的性能. 由于尿素的加入, 聚合物膜呈现均匀的微孔结构, 室温下的电导率从1.1×10^-3 S·cm^-1提高到2.15×10^-3 S·cm^-1. 同时, 锂电极/聚合物电解质界面上的电荷传递电阻也从480 Ω·cm²降低到 250 Ω·cm². 电化学稳定窗口为5.0 V. 电池(Li/PE支撑的GPE/LiCoO₂)的测试证明, 用尿素作为造孔剂的凝胶聚合物锂离子电池表现出优良的倍率性能和循环性能.     

离子液体C3MIBF4和C5MIBF4溶解焓的研究

在298.15 K下利用等温环境溶解反应热量计测定了离子液体C₃MIBF₄(四氟硼酸1-甲基-3-丙基咪唑)和C₅MIBF₄(四氟硼酸1-甲基-3-戊基咪唑)不同浓度水溶液的摩尔溶解焓(Δ_sH_m). 借助Pitzer电解质溶液理论, 得到了它们的标准摩尔溶解焓 和Pitzer焓参数: 和 , 并计算了表观相对摩尔焓. 根据Glasser理论计算了离子液体晶格能, 进而估算了离子液体C₅MIBF₄和C₃MIBF₄中正离子的水化焓分别为－171 kJ•mol^－1 (C₅MI^＋)和－207 kJ•mol^－1 (C₃MI^＋).     

离子液体C3MIBF4和C5MIBF4溶解焓的研究

在298.15 K下利用等温环境溶解反应热量计测定了离子液体C₃MIBF₄(四氟硼酸1-甲基-3-丙基咪唑)和C₅MIBF₄(四氟硼酸1-甲基-3-戊基咪唑)不同浓度水溶液的摩尔溶解焓(Δ_sH_m). 借助Pitzer电解质溶液理论, 得到了它们的标准摩尔溶解焓 和Pitzer焓参数: 和 , 并计算了表观相对摩尔焓. 根据Glasser理论计算了离子液体晶格能, 进而估算了离子液体C₅MIBF₄和C₃MIBF₄中正离子的水化焓分别为－171 kJ•mol^－1 (C₅MI^＋)和－207 kJ•mol^－1 (C₃MI^＋).     

聚合时间对染料敏化太阳能电池中聚苯胺对电极结构和性能的影响

采用恒电压方法, 以掺杂氟的SnO₂ (FTO)导电玻璃为基底, 采用不同的聚合时间制备SO₄^2?掺杂的聚苯胺对电极(PANI CEs). 利用扫描电子显微镜(SEM)、紫外-可见(UV-Vis)吸收光谱、循环伏安法(CV)和电化学阻抗谱(EIS)等技术详细研究了聚合时间对PANI CEs的表面形貌、结构(如掺杂度、共轭性、氧化态等)和对I^?/I^3?的催化活性的影响. SEM结果表明PANI在FTO上的生长分两个阶段. 适当增加聚合时间可以增加PANI CEs的比表面积, 为催化I^?/I^3?反应提供更多的活性位点, 同时聚苯胺链的共轭性、半氧化态聚苯胺(EB)结构的含量和对阴离子SO₄^2?的掺杂度会随着增加, 进而PANI 的导电率也逐渐增大. 然而, 聚合时间过长会引起薄膜厚度的增加和氧化结构的过多, 使PANI CEs的导电率降低, 电子在PANI 薄膜中的传输阻抗增加, 进而影响其对I^?/I^3?的催化性能. 聚合时间为300 s 时制备出的PANI 薄膜作为染料敏化太阳能电池(DSSCs)对电极和以D149 为染料时, 获得的最高电池光电转换效率为5.30%, 可达到基于Pt 对电极电池效率的88%. 因此, 通过电化学方法制备的PANI CEs有望代替贵金属Pt CEs用于DSSCs中.     

P(VdF-HFP)-基离子液体复合聚合物电解质的阴极稳定性及热稳定性

以聚偏氟乙烯-六氟丙烯P(VdF-HFP)聚合物为基体, 制备了含离子液体1-甲基-3-乙基咪唑六氟磷酸盐(EMIPF6)、用于锂离子电池的离子液体复合聚合物电解质[P(VdF-HFP)/LiPF₆/EMIPF₆/EC(碳酸乙烯酯)-PC(碳酸丙烯酯)]. 采用热重分析法以及燃烧实验测试了复合聚合物电解质的热稳定性. 离子电导率测试表明, 离子液体的存在显著改善了复合聚合物电解质的离子传输; 循环伏安测试表明, 添加剂EC和PC的加入提高了复合电解质的阴极稳定性, 制得的离子液体复合聚合物电解质在0.3-4.3 V 电压范围内稳定存在. Li₄Ti₅O₁₂ 和LiCoO₂为电极材料、P(VdF-HFP)/LiPF₆/EMIPF₆/EC-PC 为电解质的半电池表现出优良的循环性能, 0.1C充放电倍率下, Li/LiCoO₂和Li/Li₄Ti₅O₁₂半电池的可逆容量分别为130和144 mAh·g^-1. 但EC、PC在一定程度上降低了离子液体复合聚合物电解质的热稳定性.     

一种可高温运行的离子液体电解质燃料电池

本文采用N-甲基咪唑为原料通过溴盐的中间步骤合成了1-乙基-3甲基咪唑磷酸二氢盐([Emim]H₂PO₄)离子液体。首先利用元素分析和核磁共振确定了其组成,并测量了该离子液体的粘度和电导性能,然后使用多孔的聚偏氟乙烯作为支撑制备了离子液体电解质复合膜,120 ℃时通过交流阻抗测得其电导率为2.7×10^-2 S·cm^-1。最后将该复合膜组装在单电池中测试了不同温度下的性能,常压下120 ℃时可获得0.85 mW·cm^-2的功率密度,结果表明该复合膜的质子传导可以完全不依赖水,从而能够实现高温操作。     

一种新型有机硅离子液体电解液在超级电容中的应用

设计合成了一种新型有机硅室温离子液体(SiN1IL), 并对其化学结构和电化学窗口进行表征, 通过与具有高介电常数的丙烯碳酸酯(PC)/低粘度的乙腈(AN)匹配组成电解液, 其离子电导率达到商业实际应用的要求(19.6 mS·cm^-1). 对以活性炭(AC)为对称电极的超级电容器的电化学性能测试表明, SiN1IL 基电解液与活性炭有很好的界面相容性, 其高倍率充放电、阻抗性能优于商用四乙基四氟硼酸铵(Et₄NBF₄)/PC 电解液, 在电流密度为1000 mA·g^-1的条件下, 工作电压为2.7 V, 其比电容为108 F·g^-1.     

基于新型交联聚合物电解质的准固态染料敏化太阳能电池

采用柠檬酸(CA)交联聚乙二醇(oligo-PEG, 平均分子量M_w=200, 400, 1000, 2000), 合成具有可生物降解性能的聚柠檬酸-乙二醇(PCE)交联聚酯, 并以此为基体材料制备得到准固态的三维交联型PCE/LiI/I₂聚合物电解质. 采用红外吸收光谱(IR)、核磁共振氢谱(¹H-NMR)、扫描电镜(SEM)和Raman光谱分别对PCE基体的分子结构、聚合物电解质的微观形貌以及导电离子对的存在形式进行表征; 通过线性扫描伏安法(LSV)研究了聚合物电解质的离子扩散系数、电导率以及电池的输出电流-电压(I-V)性能. 结果表明, PEG的分子量影响PCE基体膜的微观形貌及其吸液性能, 从而影响聚合物电解质的离子导电性能及电池的光电性能: 随着PEG分子量M_w从200, 400, 1000增大到2000, PCE基体膜的结构变得疏松, 吸液率增加, 吸液溶胀后的基体中I-3的跃迁活化能降低, 导致电解质的电导率和电池的短路光电流密度随之增加; 在60 mW·cm^-2的入射光强下, 四种电解质对应电池的光电转化效率依次为3.26%、3.34%、4.26%和4.89%.     

Boron-incorporated Sulfonated polysulfone/polyphosphoric acid electrolytes for supercapacitor application

In the present work, boron-doped multicomponent gel polymer electrolytes composed of host polymer, sulfonated polysulfone (SPSU) and the additives; ionic liquid, 1-ethyl-3-methyl-imidazolium tetrafluoroborate (IL), H₃BO₃, polyphosphoric acid (PPA) were prepared. Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) techniques were used to characterize the sulfonated polysulfone-based electrolytes. Ion conductivity of these gel electrolytes were studied by dielectric impedance analyzer within the temperature from ?20 to 100°C. The ionic conductivity of the SPSU-5IL-1PPA and SPSU-5IL-1H₃BO₃-1PPA were measured as 4.8 × 10^?3 and 9 × 10^?4 S cm^?1, respectively. Supercapacitor having activated carbon-based composite electrode and electrolyte was constructed with the configuration: Al/C/electrolyte/C/Al. The electrochemical properties and ion transfer characteristics of the supercapacitor were investigated by the cyclic voltammetry (CV). Galvanostatic charge—discharge experiments exhibited good electrochemical reversibility and produced a specific capacitance value of 120 F g^?1 at 1 A g^?1. The symmetric supercapacitor system was retained almost 85% of its initial activity after 1000 cycle.     

侧链型磺化聚芳醚酮/磺化聚乙烯醇复合型直接甲醇燃料电池用质子交换膜

通过溶液共混法制备了不同磺化聚乙烯醇(SPVA)含量的侧链型磺化聚芳醚酮/磺化聚乙烯醇(S-SPAEK/SPVA)复合膜. 应用红外光谱(FTIR)对复合膜进行了表征, 扫描电镜(SEM)显示SPVA均匀分布在复合膜中. 通过对复合膜的性能测试发现该系列复合膜具有良好的热性能、较高的吸水率和保水能力. SPVA中的羟基能有效地阻碍甲醇的透过, 甲醇渗透系数从S-SPAEK/SPVA5 复合膜的7.9×10^-7 cm²·s^-1降低到S-SPAEK/SPVA30的1.3×10^-7 cm²·s^-1, 比S-SPAEK膜的11.5×10^-7 cm²·s^-1降低了一个数量级. SPVA的引入增加了亲水基团数量, 增加了复合膜的吸水和保水能力, 有利于质子按照“Vehicle”机理和“Grotthuss”机理进行传递, 柔软的SPVA链段与S-SPAEK侧链聚集成亲水相区, 形成连续的质子传输通道, 提高了复合膜的质子传导率. 在25 和80℃ 时, S-SPAEK/SPVA30 复合膜的质子传导率分别达到了0.071 和0.095 S·cm^-1. 可见,S-SPAEK/SPVA复合膜有望在直接甲醇燃料电池中得到应用.     

Low glass transition temperature polymer electrolyte prepared from ionic liquid grafted polyethylene oxide

In this contribution, we report a new type of poly (ionic liquids) prepared by imidazolium ionic liquids directly grafting onto polyethylene oxide backbone. Different molecular weights of poly (ionic liquids) are obtained with a low glass transition temperature up to ?14 °C. The materials as polymer electrolyte achieve a high conductivity around 10^?5 S cm^?1 at 30 °C and close to 10^?3 S cm^?1 at 90 °C. High viscosity up to 4000 Pa s at room temperature would minimize the electrolytes leaking in electrochemical devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2104–2110     

染料敏化纳米薄膜太阳电池中离子液体基电解质的研究进展

综述了离子液体基电解质在染料敏化纳米薄膜太阳电池中的研究及应用进展，详细论述了多种离子液体基电解质系统对染料敏化纳米薄膜太阳电池性能的影响，并比较了这些系统的优缺点. 根据胶凝剂的不同分别论述了离子液体基电解质的固化及其对电池性能的影响. 评述了离子液体基电解质在大面积电池中的应用，并对离子液体基电解质未来发展方向进行了展望.     

The effects of polymer gel electrolyte composition on performance of quasi-solid-state dye-sensitized solar cells

Polymer gel electrolytes based on poly(acrylic acid)-poly(ethylene glycol) (PAA–PEG) hybrid have been prepared and applied to developed quasi-solid-state dye-sensitized solar cells (DSCs). PAA–PEG hybrid was synthesized by polymerization reaction. Quasi-solid-state DSCs were fabricated with synthesized PAA–PEG electrolyte. The effects of alkali iodides LiI, KI, and I₂ concentrations on liquid electrolyte absorbency and ionic conductivity of PAA–PEG were investigated. The evolution of the solar cell parameters with polymer gel electrolyte compositions was revealed. DSCs based on PAA–PEG with optimized KI/I₂ concentrations showed better performances than those with optimized LiI/I₂ concentrations. The electrochemical impedance spectroscopy technique was employed to examine the electron lifetime in the TiO₂ electrode and quantify charge transfer resistances at the TiO₂/dye/electrolyte interface and the counter electrode in the solar cells based on the PAA–PEG hybrid gels. A maximum conversion efficiency of 4.96% was obtained for DSCs using KI based quasi-solid electrolyte under 100 mW cm⁻². Our work suggests that KI can be the promising alkali metal iodide for improving the performance of PAA–PEG hybrid gel DSCs.     

High ionic conductivity of all-solid polymer electrolytes based on polyorganophosphazenes

A series of all-solid polymer electrolytes were prepared by cross-linking new designed poly(organophosphazene) macromonomers. The ionic conductivities of these all-solid, dimensional steady polymer electrolytes were reported. The temperature dependence of ionic conductivity of the all-solid polymer electrolytes suggested that the ionic transport is correlated with the segmental motion of the polymer. The relationship between lithium salts content and ionic conductivity was discussed and investigated by Infrared spectrum. Furthermore, the polarity of the host materials was thought to be a key to the ionic conductivity of polymer electrolyte. The all-solid polymer electrolytes based on these poly(organophosphazenes) showed ionic conductivity of 10⁻⁴ S cm⁻¹ at room temperature.     

离子液体在多孔碳电极上的电化学性能

制备了数种离子液体及离子液体有机溶液电解质,用线性电位扫描法测试了它们的电化学窗口;并通过循环伏安、交流阻抗、电势阶跃等电化学方法,对它们在多孔碳电极中的电化学性能进行了研究.实验结果表明:溶剂对1-乙基-3-甲基咪唑类离子液体有机溶液电解质的电化学窗口有较大的影响.离子液体及离子液体有机溶液电解质在多孔碳电极上的电化学性能与其电导率密切相关,电导率越大,充电时间常数越小,比容量越大;但比容量降低的倍率远小于电导率降低的倍率.     

Characterization and properties of ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes

Gel polymer electrolytes containing 1-ethyl-3-methylimidazolium-bis (trifluoromethyl-sulfnyl)imide (EMITFSI) ionic liquid were prepared for lithium ion batteries by solution casting method. Thermal and electrochemical properties have been determined for the gel polymer electrolytes. Proper addition of EMITFSI to the P(VdF-HFP)-LiTFSI polymer electrolyte improves the ionic conductivity and electrochemical window to 2.11 × 10⁻³ S cm⁻¹ (30 °C) and 4.6 V. In combination of the prepared ternary P(VdF-HFP)-LiTFSI-EMITFSI ionic liquid polymer electrolytes, Li₄Ti₅O₁₂ anode exhibited two extra voltage plateaus around 1.1 V and 2.3 V except the typical voltage plateau around 1.6 V by possible side reaction between ionic liquid and polymer. LiFePO₄ cathode exhibited high capacity above 140 mA h g⁻¹ and retention of 93.1% due to the suppressed polarization effect caused by enhanced ion transport properties. The high temperature of 80 °C didn't have significant impact on the cycling performance.     

Synthesis and performance of proton conducting chitosan/NH4Cl electrolyte

The polymer electrolytes based on chitosan and ammonium chloride were prepared by solution casting technique and the properties were studied. The addition of ammonium chloride results in: (1) the enhancement of the amorphous nature of the polymer electrolytes; (2) the shift of the absorption bands of amino group at 1566 cm^?1 and the carbonyl group at 1640 cm^?1 towards lower wave number, and the appearance of a new absorption band at 1759 cm^?1; (3) a decrease of the glass transition temperature. The 20 wt % ammonium chloride doped polymer electrolyte has the best room temperature electric property, the lowest activation energy and the highest ionic conductivity. Placing the as‐prepared polymer electrolyte in a dryer is adverse for the sample's moisture content, and results in higher activation energy and lower ionic conductivity. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 260–266, 2010