More line narrowing in TROSY by decoupling of long-range couplings: shift correlation and 1JNC' coupling constant measurements

Since the introduction of RDCs in high-resolution NMR studies of macromolecules, there is a growing interest in the development of accurate, and sensitive methods for determining coupling constants. Most methods for extracting these couplings are based on the measurement of the splitting between multiplet components in J-coupled spectra. However, these methods are often unreliable since undesired multiple-bond couplings can considerably broaden the multiplet components and consequently make accurate determination of their position difficult. To demonstrate one approach to this problem, G-BIRD((r)) decoupled TROSY sequences are proposed for the measurement of (1)J(NH) and (1)J(NC') coupling constants. Resolved or unresolved splittings due to remote protons are removed by a G-BIRD((r)) module employed during t(1) and as a result, spectra with narrow, well-resolved peaks are obtained from which heteronuclear one-bond couplings can be accurately measured. Moreover, introduction of a spin-state-selective alpha/beta-filter in the TROSY sequence allows the separation of the (1)J(NC') doublet components into two subspectra which contain the same number of peaks as the regular TROSY spectrum. The (1)J(NC') couplings are obtained from the displacement between the corresponding peaks in the subspectra.     

The 2D {P} Spin-Echo-Difference Constant-Time [C, H]-HMQC Experiment for Simultaneous Determination of JH3′P and JC4′P in C-Labeled Nucleic Acids and Their Protein Complexes

A two-dimensional {³¹P} spin-echo-difference constant-time [¹³C, ¹H]-HMQC experiment (2D {³¹P}-sedct-[¹³C, ¹H]-HMQC) is introduced for measurements of ³J_C4′P and ³J_H3′P scalar couplings in large ¹³C-labeled nucleic acids and in DNA–protein complexes. This experiment makes use of the fact that ¹H–¹³C multiple-quantum coherences in macromolecules relax more slowly than the corresponding ¹³C single-quantum coherences. ³J_C4′P and ³J_H3′P are related via Karplus-type functions with the phosphodiester torsion angles β and ε, respectively, and their experimental assessment therefore contributes to further improved quality of NMR solution structures. Data are presented for a uniformly ¹³C, ¹⁵N-labeled 14-base-pair DNA duplex, both free in solution and in a 17-kDa protein–DNA complex.     

Determination of Internucleotide JHN Couplings by the Modified 2D JNN-Correlated [N, H] TROSY

Recent developments in the direct observation of J couplings across hydrogen bonds in proteins and nucleic acids provide additional information for structure and function studies of these molecules by NMR spectroscopy. A J_NN-correlated [¹⁵N, ¹H] TROSY experiment proposed by Pervushin et al. (Proc. Natl. Acad. Sci. USA 95, 14147–14151, 1998) can be applied to measure ^hJ_HN in smaller nucleic acids in an E.COSY manner. However, it cannot be effectively applied to large nucleic acids, such as tRNA^Trp, since one of the peaks corresponding to a fast relaxing component will be too weak to be observed in the spectra of large molecules. In this Communication, we proposed a modified J_NN-correlated [¹⁵N, ¹H] TROSY experiment which enables direct measurement of ^hJ_HN in large nucleic acids.     

Measurement of one and two bond N–C couplings in large proteins by TROSY-based J-modulation experiments

Residual dipolar couplings (RDCs) between NC′ and NC^α atoms in polypeptide backbones of proteins contain information on the orientation of bond vectors that is complementary to that contained in NH RDCs. The ¹J_NC^α and ²J_NC^α scalar couplings between these atoms also display a Karplus relation with the backbone torsion angles and report on secondary structure. However, these N–C couplings tend to be small and they are frequently unresolvable in frequency domain spectra having the broad lines characteristic of large proteins. Here a TROSY-based J-modulated approach for the measurement of small ¹⁵N–¹³C couplings in large proteins is described. The cross-correlation interference effects inherent in TROSY methods improve resolution and signal to noise ratios for large proteins, and the use of J-modulation to encode couplings eliminates the need to remove frequency distortions from overlapping peaks during data analysis. The utility of the method is demonstrated by measurement of ¹J_NC′, ¹J_NC^α, and ²J_NC^α scalar couplings and ¹D_NC′ and ¹D_NC^α residual dipolar couplings for the myristoylated yeast ARF1·GTPγs protein bound to small lipid bicelles, a system with an effective molecule weight of 70 kDa.     

Global Entanglement Measures and Quantum Phase Transitions in the 1D J 1? J 2 Model

We have analyzed the behavior of multipartite global entanglement and average bipartite concurrence for the sign of quantum phase transitions in the frustrated J ₁−J ₂ model by using exact diagonalization technique for a chain of 12 qubits. It is found that although the magnitude of two classes of the measures show opposite trends the absolute value of their derivatives show similar structure near critical points.     

Preparation of α-Fe2O3 nanoparticles by high-energy ball milling

α-Fe₂O₃ nanoparticles were prepared by high-energy ball milling using α-FeOOH as raw materials. The prepared samples were characterized by transmission electron microscopy (TEM), Mössbauer spectroscopy, X-ray diffraction (XRD) and differential thermal analysis–thermogravimetric analysis (DTA–TGA). The results showed that after 90 h milling α-Fe₂O₃ nanoparticles were obtained, and the particle size is about 20 nm. The mechanism of reaction during milling is supposed that the initial α-FeOOH powder turned smaller and smaller by the high-speed collision during ball milling, later these particles turned to be superparamagnetic, at last these superparamagnetic α-FeOOH particles were dehydrated and transformed into α-Fe₂O₃.     

Novel nanostructures of β-Ga2O3 synthesized by thermal evaporation

In this study, we report the novel β-Ga₂O₃ nanostructures synthesized by the thermal evaporation of Ga droplet in the presence of Au catalysts at 900 °C. The morphology and structure of the products were analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The single-crystalline β-Ga₂O₃ nanosheets have lateral dimensions up to several tens of microns. Large arrays of column-like layered crystal β-Ga₂O₃ structures that consisted of many nanosheets were formed on the Au-coated silicon substrate under the suitable vapor concentration. These novel β-Ga₂O₃ nanostructures are expected to have potential application in functional nanodevices.     

External cavity tunable diode laser spectra of the ν1 + 2ν4 stretch-bend combination bands of NH3 and NH3

The ammonia ν₁ + 2ν₄ perpendicular stretch-bend combination band has been investigated in spectra of ¹⁴NH₃ and ¹⁵NH₃ recorded in the 6400-6800 cm⁻¹ region with an external cavity tunable diode laser (ECTDL) spectrometer. For ¹⁴NH₃, new assignments were determined initially by extrapolating from published low-J jet-cooled beam results up to transitions of higher J and K. Corresponding ν₁ + 2ν₄ transitions for the ¹⁵NH₃ species were then found by identifying similar patterns of lines with a characteristic downshift of approximately 9.7 cm⁻¹. Assignments were confirmed employing ground-state combination differences. Term values, a-s inversion splittings, l-doubling energies and parameter estimates from simple single-state fits are reported for the two ammonia species.     

Growth and properties of air-processed GdBa2Cu3O7−δ superconductors with fined Gd2BaCuO5 and Gd2Ba4CuFeOy additions

We have succeeded in synthesizing a powder form of Gd₂Ba₄CuFeO_y (Gd2411) in air. GdBa₂Cu₃O_7−δ (Gd123)/Gd₂BaCuO₅ (Gd211) precursor powders added with different amounts of Gd₂Ba₄CuFeO_y (x = 0, 0.002, 0.004, 0.02) in molar ratio to Gd123 have been fabricated successfully into the form of large, single grains by the top seeded melt growth (TSMG) process. The relation between the additions amounts of Gd2411/Gd211 and critical current density (J_C) was analyzed. We found Gd2411 particles stably exist in the Gd123 matrix without degradation of superconducting properties owing to the existence of the Fe magnetic ion. The trapped field was observed to increase significantly compared with the bulk without Gd2411 additions.     

Effect of intervening structure between CuO2 sheets in heavily Fe-substituted high-Tc superconductor FeSr2YCu2O6+δ

Heavily Fe-substituted Ba₂YCu₃O_6+δ-type compound FeSr₂YCu₂O_6+δ exhibits superconductivity around 60 K, only when it is annealed in N₂ and subsequently in O₂. Cationic distribution in this compound is strongly dependent on ionic radius at the Y site, and its superconducting properties are affected by the cationic distribution. In contrast, although the compound with the substitution of fluorite-type unit for Y has cationic order, it does not exhibit superconductivity. We have analyzed the crystal structure of the compounds with the substitution of other lanthanoid elements for Y and with substitution of fluorite-type unit for Y.     

Transport properties and defect analysis of La1.9Sr0.1NiO4 + δ

The oxygen flux through La_1.9Sr_0.1NiO_4 + δ has been measured as a function of oxygen activity gradient and temperature (750–1000 °C). The oxygen nonstoichiometry was determined by thermogravimetry in the temperature range of 400–1000 °C and oxygen partial pressures of 0.0002–1 atm. The total conductivity was measured over a similar range of conditions. The oxide ion partial conductivity derived from the oxygen flux data is approximately 4 orders of magnitude lower than the total, mainly p-type electronic conductivity. The defect structure was derived based on the data. Combining the oxygen flux and oxygen nonstoichiometry, the self diffusion coefficient of oxygen interstitials was evaluated.     

Effect of Y2O3 addition on the conductivity and elastic modulus of (CeO2)1 − x(YO1.5)x

The conductivity and elastic modulus of (CeO₂)_1 − x(YO_1.5)_x for x values of 0.10, 0.15, 0.20, 0.30, and 0.40 were investigated by experiments and molecular dynamics simulations. The calculated conductivity exhibited a maximum value at approximately 15 mol% Y₂O₃; this trend agreed with that of the experimental results. In order to clarify the reason for the occurrence of the maximum conductivity, the paths for the transfer of oxygen vacancies were counted. The numerical result revealed that as the content of Y₂O₃ dopant increases, the number of paths for the transfer of oxygen vacancies decreases, whereas the number of oxygen vacancies for conductivity increases. Thus, the trade-off between the increase in the number of vacancy sites and the decrease in the vacancy transfer was considered to be the reason for the maximum conductivity occurring at the Y₂O₃ dopant content of approximately 15 mol%. The calculated elastic modulus also exhibited a minimum value at approximately 20 mol% Y₂O₃, which also agreed with the experimental results. It was shown that the Y–O–Y bonding energy increased with the increasing content of Y₂O₃ dopant. Thus, the trade-off between the increase in the number of vacancy sites and that in the Y–O–Y bonding energy was considered to be the reason for the minimum elastic modulus occurring at the Y₂O₃ dopant content of approximately 20 mol%.     

Synthesis and electrical properties of In2O3(ZnO)m superlattice nanobelt

One-dimensional（ID） In₂O₃（ZnO）_m superlattice nanobelts are synthesized by a chemical vapor deposition method.The formation of the In₂O₃（ZnO）_m superlattice is verified by the high-resolution transmission electron microscopy images.The typical zigzag boundaries could be clearly observed.An additional peak at 614 cm^-1 is found in the Raman spectrum,which may correspond to the superlattice structure.The study about the electrical transport properties reveals that the In₂O₃（ZnO）_m nanobelts exhibit peculiar nonlinear I-V characteristics even under the Ohmic contact measurement condition,which are different from the Ohmic behaviors of the In-doped ZnO nanobelts.The photoelectrical measurements show the differences in the photocurrent property between them,and their transport mechanisms are also discussed.     

Polyacrylonitrile electrolytes: 1. A novel high-conductivity composite polymer electrolyte based on PAN, LiClO4 and α-Al2O3

In this work, a series of novel solid-type α-Al₂O₃-containing polyacrylonitrile (PAN)-based composite polymer electrolytes (CPE) with high conductivity and high mechanical property at room temperature has been prepared. The effect of the addition of α-Al₂O₃ on the properties of the PAN-based composite polymer electrolyte has been analyzed. The best conductivities obtained at room temperature is 5.7×10⁻⁴ S cm⁻¹ from the CPE with 7.5 wt.% α-Al₂O₃ and 0.6 LiClO₄ per PAN repeat unit. The stress–strain test result indicates that the membranes prepared possess high yield stress (73 kg cm⁻²) suitable for serving as separators in the solid-state lithium and lithium ion batteries and high yield elongation (225%) pliable to form good interface with electrodes. Also discussed are the effects of the addition of the ceramics on the interactions in the system and the possible conduction mechanism.     

Two-fold interferometric measurements of piezo-optic constants: application to β-BaB2O4 crystals

We present the interferometric technique which allows to measure piezooptical and photoelastic characteristics of crystal materials of any symmetry. The offered two-fold interferometric method enables to determine all independent non-zero piezooptic and photoelastic constants by measuring pressure induced changes of optical path. As advantage to known acoustooptical techniques this method allows to measure both the absolute magnitude and sign of photoelastic constants. In general case the determination of 36 components of piezooptic tensor needs to carry out 57 measurements on 16 samples. The corresponding relationships are derived. As an example we apply here the interferometric technique to measure the piezooptic and photoelastic constants in trigonal β-BaB₂O₄ crystals.     

Oxygen vacancy in LiTiPO5 and LiTi2(PO4)3: A first-principles study

The structures of LiTiPO₅ and LiTi₂(PO₄)₃, as well as the possibility of oxygen vacancies formation in the systems are studied by first-principles calculations. It is found that oxygen vacancies can be formed in LiTiPO₅ and LiTi₂(PO₄)₃ under oxygen poor condition. The formation of oxygen vacancies introduce a defect band within their band gaps, which is expected to improve the electronic conductivity of LiTiPO₅ and LiTi₂(PO₄)₃ significantly. Meanwhile, a great concentration of oxygen vacancies may increase the discharge voltage of LiTiPO₅ and LiTi₂(PO₄)₃.     

Optical characterization of fourfold (Td)- and sixfold (Oh)-transition-metal species in MgAl2O4:Co by time-resolved spectroscopy

This work investigates the origin of novel visible photoluminescence (PL) bands observed in the spinel MgAl₂O₄:Co²⁺. Besides the well-known fourfold-coordinated Co²⁺(T_d) PL at 670 nm [N.V. Kuleshov, V.P. Mikhailov, V.G. Scherbitsky, P.V. Prokoshin and K.V. Yumashev, J. Lumin. 55 (1993) 265.], a rich structured PL band at 686 nm was also observed that we associate with uncontrolled impurities of sixfold coordinated Cr³⁺(O_h) by time-resolved spectroscopy and lifetime measurements and their variation with temperature. We also show that the lifetime of the Co²⁺(T_d) emission at 670 nm varies from τ=6.7 μs to 780 ns on passing from T=10 to 290 K. This unexpected behaviour for T_d systems is related to the excited-state crossover (⁴T₁↔²E), making the emission band to transform from a narrow-like emission from ²E at low temperature to a broad structureless band from ⁴T₁ at room temperature.     

Quasi-two-dimensional magnetism in (CnH2n+1NH3)2CuCl4 studied by electron paramagnetic resonance

The quasi-two-dimensional magnetism in the layered transition metal compound (C_nH_2n+1NH₃)₂CuCl₄ (n=10, 14) was investigated by means of electron paramagnetic resonance (EPR) and superconducting quantum interference device measurements. As a result, the high temperature magnetic phase transitions were reflected in the EPR parameters in a sensitive manner.     

Lithium ion conductive glass–ceramics with Li3Fe2(PO4)3 and YAG laser-induced local crystallization in lithium iron phosphate glasses

The glasses with the composition of 37.5Li₂O–(25 − x)Fe₂O₃–xNb₂O₅–37.5P₂O₅ (mol%) (x = 5,10,15) are prepared, and it is found that the addition of Nb₂O₅ is effective for the glass formation in the lithium iron phosphate system. The glass–ceramics consisting of Nasicon-type Li₃Fe₂(PO₄)₃ crystals with an orthorhombic structure are developed through conventional crystallization in an electric furnace, showing electrical conductivities of 3 × 10^− 6 Scm^− 1 at room temperature and the activation energies of 0.48 eV (x = 5) and 0.51 eV (x = 10) for Li⁺ ion conduction in the temperature range of 30–200 °C. A continuous wave Nd:YAG laser (wavelength: 1064 nm) with powers of 0.14–0.30 W and a scanning speed of 10 μm/s is irradiated onto the surface of the glasses, and the formation of Li₃Fe₂(PO₄)₃ crystals is confirmed from XRD analyses and micro-Raman scattering spectra. The crystallization of the precursor glasses is considered as new route for the fabrication of Li₃Fe₂(PO₄)₃ crystals being candidates for use as electrolyte materials in lithium ion secondary batteries.     

Infrared (IR) stimulated luminescence from αAl2O3:C

Infrared (IR) stimulated luminescence from α---Al₂O₃:C single crystals was investigated. The data show that the IR-stimulated luminescence curve contains at least two overlapping signals. One of the components was found to be both thermally and optically unstable whereas the second component was thermally stable and slowly decaying under constant stimulation. The slow decaying component was found to be very sensitive to radiation dose. It was found that doses smaller than 1 mGy could be measured and the luminescence could be read several times without significant depletion of the signal.