In situ derivatisation using pressurized liquid extraction to determine phenols, sterols and carboxylic acids in environmental samples and microbial biomasses

Pressurized liquid extraction was combined with in-situ derivatisation to extract polar analytes such as phenols (including chlorophenols) sterols and carboxylic acids from environmental and microbial samples. This one-step protocol uses acetic anhydride as an acetylation agent, N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) as an silylation agent, and boron trifluoride-methanol, phenyltrimethyl ammoniumhydroxide and trimethyl sulfoniumhydroxide as methylation agents. It results in faster extraction rates and better or comparable extraction efficiencies when compared to classical approaches. The addition of a silylation agent also facilitates the extraction kinetics of analytes not accessible to silylation (e.g. polycyclic aromatic hydrocarbons or alkylbenzenes). This may be attributed to a dissociative action of the agent to weaken analyte-matrix interactions.     

Multi-class determination of antimicrobials in meat by pressurized liquid extraction and liquid chromatography-tandem mass spectrometry

A multi-residue method using pressurized liquid extraction (PLE) and liquid chromatography-tandem mass spectrometry (LC-MS/MS) has been developed for determining trace levels of 31 antimicrobials, including beta-lactams, lincosamides, macrolides, quinolones, sulfonamides, tetracyclines, nitroimidazoles and trimethoprim. The extraction method required pre-homogeneization of the meat with EDTA-washed sand and subsequent one-static-cycle extraction for 10 min with 40 ml of water at 1500 psi and 70 degrees C. The effect of operation temperature, pressure, flush volume, and static cycles on PLE performance was studied. Average recoveries ranged from 75 to 99% with relative standard deviations <18%. The method was validated according to the European Union requirements (2002/657/EC). In addition to the quality parameters included in that decision, the limits of detection (LODs) and quantification (LOQs) were determined. The use of LC-MS/MS provided LODs (between 3 and 15 microg kg(-1)) and LOQs (between 10 and 50 microg kg(-1)), by far lower than half of their maximum residue limits (MRLs) (between 50 and 1200 microg kg(-1)). Confirmation of the presence of any of the studied compounds was accomplished in 1h after sample receipt. This methodology has been successfully applied to the analysis of cattle and pig tissue samples from local markets and slaughterhouses of the Valencian Community (Spain). The results showed the presence of some antimicrobials at different concentrations. Quinolones and tetracyclines were the antimicrobials most detected in cattle and pig samples, respectively. Sulfonamides were also frequently detected in both types of samples.     

Application of pressurized liquid extraction followed by gas chromatography-mass spectrometry to determine 4-nonylphenols in sediments

A time- and solvent-saving method, pressurized liquid extraction (PLE), to extract 4-nonylphenol (4-NP) in sediment was developed. The effects of various operational parameters (i.e., temperature, pressure, etc.) for the quantitative extraction of 4-NP by PLE were investigated. The analytes were then identified and quantitated by a large-volume injection GC-MS technique. The 4-NP can be completely extracted by methanol at 100 degrees C and 100 atm combined with 15 min static and then 10 min dynamic extraction steps (1 atm = 101,325 Pa). Recovery of 4-NP in spiked blank kaolin samples was 98% with 5% RSD. The degrees of recovery of 4-NP in the spiked sediment samples from a reservoir and a polluted river were 111% with 4% RSD and 106% with 5% RSD, respectively. The perfect applicability of PLE for 4-NP was determined after testing it with spiked and aged samples. The extraction efficiency of the PLE was compared with conventional Soxhlet and bath ultrasonication extraction methods using the spiked sediment samples.     

Application of pressurized fluid extraction to determine cadmium and zinc in plants

A procedure for the determination of Cd and Zn in plants is proposed. The metals are extracted by pressurized fluid extraction (PFE). Operational conditions are: pressure 1500 psi, temperature 75 °C, static time 5 min, flush volume 35%, purge time 60 s, cycles 1 and 1,2-diaminocyclohexane-N,N,N′,N′-tetraacetic acid (CDTA) 0.01 M at pH 4.5 as extracting solution. Determination of Zn is carried out by flame atomic absorption spectroscopy and depending on the concentration level, Cd content is determined by flame or electrothermal atomic absorption spectroscopy. Certified samples of Virginia tobacco leaves, tea leaves, spinach leaves, poplar leaves, a commercial spinach sample (Spinacea oleracea) and genetically modified Arabidopsis thaliana were analysed by the proposed procedure and also by microwave acid digestion and extraction with HCl-Triton X-100. Confidence intervals for Cd and Zn content obtained by the proposed procedure overlap with the certified values. The other procedures, however, provide inaccurate results for Cd. Recoveries obtained for a confidence level of 95% are 96 ± 6% and 95 ± 5% for Zn and Cd, respectively. Reproducibility of Zn by the proposed procedure is 7% (n = 8), similar to the other tests and the detection limit is 2.6 μg. For Cd reproducibility is 8.5% (n = 8), better than with HCl-Triton X-100 and similar to acid digestion, the detection limit is 3.5 ng of Cd.     

Analysis of Metribuzin and transformation products in soil by pressurized liquid extraction and liquid chromatographic-tandem mass spectrometry

A method developed for study of metribuzin degradation in soil is presented. LC-MS-MS and electrospray ionisation was used for analysis of metribuzin and the metabolites deaminometribuzin (DA), diketometribuzin (DK) and deaminodiketometribuzin (DADK). Soil samples were extracted by pressurized liquid extraction using methanol-water (75:25) at 60 degrees C. In general, recoveries were about 75% for metribuzin, DA and DADK and their detection limit in soil was 1.25 microg/kg. Lower sensitivity was observed for DK, with detection limit at 12.5 microg/kg and recovery about 50%.     

Simultaneous determination of saponins and fatty acids in Ziziphus jujuba (Suanzaoren) by high performance liquid chromatography-evaporative light scattering detection and pressurized liquid extraction

The seed of Ziziphus jujube Mill. var. spinosa (Bunge) Hu ex H. F. Chou, Suanzaoren in Chinese, is one of commonly used Chinese medicines. Saponins and fatty oil contains several fatty acids in Suanzaoren are responsible for its therapeutic activities. In this study, a new HPLC coupled with evaporative light scattering detection (ELSD) and pressurized liquid extraction (PLE) method was developed for the simultaneous quantitative determination of 11 major components of 2 saponins and 9 fatty acids, namely jujuboside A, jujuboside B, lauric acid, myristic acid, palmitic acid, palmitoleic acid, stearic acid, oleic acid, linoleic acid, arachidic acid and docosanoic acid in Suanzaoren. Simultaneous separation of these eleven compounds was achieved on a C18 analytical column. The mobile phase consisted of (A) 0.1% aqueous acetic acid and (B) methanol with 0.1% acetic acid using a gradient elution. The drift tube temperature of ELSD was set at 75 degrees C, and nitrogen flow-rate was 1.8l/min. All calibration curves showed good linearity (r(2)>0.9955) within test ranges. This method showed good reproducibility for the quantification of these eleven components in Suanzaoren with intra- and inter-day variations of less than 3.41 and 4.37%, respectively. The validated method was successfully applied to quantify 11 investigated components in nine commercial samples of Suanzaoren.     

Determination of fat content and fatty acid composition in meat and meat products after supercritical fluid extraction

Two different relatively simple, commercially available supercritical fluid extractors (SFE), Leco and Foss-Tecator, were tested for the determination of total fat content in meat and meat products. The fatty acid composition in meat and meat products was also determined after the Foss-Tecator extraction in an aliquot of the extract. Total fat was determined by weighing after the different extraction procedures and the fatty acid composition by gas chromatography after hydrolysis and methylation of the extract. The results for total fat content agreed well with results from a standard method of Schmid, Bondzynski, and Ratzlaff, which uses conventional solvent extraction. Fatty acid composition was compared with the Bligh and Dyer extraction, and showed good agreement. The average relative difference between SFE and Bligh and Dyer of all fatty acids in the sample was <3% for acids exceeding 0.5% of total fatty acid amount. The advantages of SFE over traditional methods are a much lower consumption of hazardous organic solvents and shorter extraction times. To obtain quantitative recoveries by SFE, ethanol was added to the extraction cells before extraction.     

Comparison of soxhlet, ultrasound-assisted and pressurized liquid extraction of terpenes, fatty acids and Vitamin E from Piper gaudichaudianum Kunth

This paper describes a comparative study of extraction methods of terpenes (terpenic alcohols and phytosterols), fatty acids and Vitamin E from leaves of Piper gaudichaudianum Kunth. The analysis of extracts was done by gas chromatography with mass spectrometric detection. The identification and quantification was made by co-injections of the extract with certified standards. The use of pressurized liquid extraction (PLE; Dionex trade name: ASE, for accelerated solvent extraction) decrease significantly the total time of extraction, the amount of solvent and the manipulation of sample and solvents in comparison with soxhlet (SE) and ultrasound-assisted (USE). In addition, PLE was more effective for the extractions of terpenes (terpenic alcohols and phytosterols), fatty acids and Vitamin E.     

In-line solid-phase extraction preconcentration in capillary electrophoresis-tandem mass spectrometry for the multiresidue detection of quinolones in meat by pressurized liquid extraction

We have developed and validated a CE-MS/MS method using an in-line SPE device (analyte concentrator, AC) to determine eight quinolones of veterinary use whose maximum residue levels in animal edible tissues are established by the EU Council Regulation 2377/90, i.e., danofloxacin, sarafloxacin, ciprofloxacin, marbofloxacin, enrofloxacin, difloxacin, oxolinic acid, and flumequine. Different parameters affecting the AC performance, such as its design (in this case frit-free), the kind of sorbent (Oasis MCX), sample pH, volume, and composition of the elution plug and injection time were studied. The method was validated using standard solutions obtaining LODs between 17 and 59 ng/L. Finally, a pressurized liquid extraction (PLE) method was developed to determine these antibiotics in chicken muscle samples. The whole analytical method was validated in terms of linearity (r2 >or= 0.992), recoveries (63-112%), repeatability and intermediate precision (RSD 相似文献   

Determination of antioxidants in polyolefins by pressurized liquid extraction prior to high performance liquid chromatography

The effect that a high amount of mineral filler might have on the extraction process of antioxidants from polyethylene and polypropylene was investigated. Extraction of Irganox 1010, Irganox 1076 and Irgafos 168, along with its oxidation product 2,4-di-tert-butylphenol, from freeze ground polyethylene–based (PE–based) and polypropylene–based (PP–based) mineral concentrates of 85 w/w calcium carbonate (CaCO₃) and 75 w/w talc was carried out by pressurized fluid extraction (PLE) prior to high performance liquid chromatography (HPLC). Results indicate that 85 w/w CaCO₃ did not affect the extraction process from PE or PP. For talc concentrates, additive recovery from PE and PP was considerably lower. The relation of recovery yield and mixing time was investigated for the talc concentrates and it was concluded that the presence of talc seemed to accelerate the rate of antioxidant consumption during sample processing, thus, less antioxidant was left to be extracted from the polyolefin; rather than talc has limited the extraction process. The method developed in this work has been applied to determine these compounds in several commercial samples.     

Identification of degradation products in loxoprofen sodium adhesive tapes by liquid chromatography-mass spectrometry and dynamic pressurized liquid extraction-solid-phase extraction coupled to liquid chromatography-nuclear magnetic resonance spectroscopy

Rapid and unambiguous identification of three degradation products (DP-1, DP-2 and DP-3) found in heat-stressed loxoprofen sodium adhesive tapes (Loxonin tapes) was achieved by LC-MS and dynamic pressurized liquid extraction (PLE)-solid-phase extraction (SPE) coupled to LC-NMR without complicated isolation or purification processes. The molecular formulae of the degradation products were determined by accurate mass measurements and product ion analyses and on-line hydrogen/deuterium (H/D) exchange experiments provided information about changes in the degradation of loxoprofen. To compensate for the low sensitivity of NMR, on-line dynamic PLE-SPE was employed and higher concentrations of degradation products trapped on the SPE column were afforded in a shorter time than they would be in such time-consuming sample preparations as pre-concentration after extraction. The loop-storage procedure was used in the LC-NMR analysis to allow the acquisition of the (1)H spectra of the three degradation products in one chromatographic run without affecting the peak separation and to avoid the carry-over of previously eluted DP-1 of high concentration by washing the NMR detection cell prior to the measurement of the DP-2 spectrum. Based on the resulting (1)H NMR spectra in combination with the MS results, DP-1 was successfully identified as an oxidation product having an oxodicarboxylic acid structure formed by the cleavage of the cyclopentanone ring of loxoprofen, DP-2 as a cyclopentanone ring-hydroxylated loxoprofen and DP-3 as a loxoprofen l-menthol ester.     

Solid-phase extraction and liquid chromatography--mass spectrometry for the determination of free fatty acids in shellfish

A novel analytical protocol for the determination of free fatty acids (FFAs; saturated, monounsaturated and polyunsaturated) in shellfish using electrospray ionisation and liquid chromatography-mass spectrometry (LC-MS) is described. Total lipids were extracted from four commercially important shellfish species using chloroform-methanol in a modification of the traditionally used Bligh and Dyer method. FFAs were recovered from lipidic shellfish extracts by solid-phase extraction (SPE) on an aminopropyl-silica column using a 98:2 v/v diethyl ether (DEE)-acetic acid solution. Ether extracts containing the FFAs were evaporated and reconstituted in 70:30 v/v methanol-chloroform before analysis by LC-MS. The limits of quantification (LOQs) of the method ranged from 60 to 560 microgg(-1) wet weight depending on the different FFAs determined with selected ion monitoring (SIM). Results demonstrate that LC-MS is well suited for identification and quantification of FFAs in shellfish and negates the use of sample derivatisation required in gas chromatographic analysis.     

Comparison of two gas–liquid chromatograph columns for the analysis of fatty acids in ruminant meat

Two gas–liquid chromatograph capillary columns for the analysis of fatty acids (FA) in ruminant fat are compared. Those columns are the CP-Sil 88 of 100 m long with a highly polar stationary phase and the Omegawax 250 of 30 m long with a stationary phase of intermediate polarity. Fatty acid methyl ester (FAME) patterns of branched-chain, cis and trans octadecenoate isomers, as well as conjugated and non-conjugated 18:2 and 18:3 isomers are fairly different between columns, even though most of the FAME could be separated on either column. However, the CP-Sil 88 showed better resolution of 18:1 isomers than Omegawax 250. The analysis of 96 samples of ruminant meat fat in both chromatographic systems showed that averages obtained for total FA content and for most of the individual FA did not differ between columns. Moreover, regression analysis of Omegawax and CP-Sil 88 data is highly correlated. Quantitative differences between chromatographic systems were detected for samples containing more than 66 mg fatty acids per gram of muscle dry matter.     

FT-midIR determination of fatty acid profiles, including trans fatty acids, in bakery products after focused microwave-assisted Soxhlet extraction

A study of the feasibility of Fourier transform medium infrared spectroscopy (FT-midIR) for analytical determination of fatty acid profiles, including trans fatty acids, is presented. The training and validation sets—75% (102 samples) and 25% (36 samples) of the samples once the spectral outliers have been removed—to develop FT-midIR general equations, were built with samples from 140 commercial and home-made bakery products. The concentration of the analytes in the samples used for this study is within the typical range found in these kinds of products. Both sets were independent; thus, the validation set was only used for testing the equations. The criterion used for the selection of the validation set was samples with the highest number of neighbours and the most separation between them (H<0.6). Partial least squares regression and cross validation were used for multivariate calibration. The FT-midIR method does not require post-extraction manipulation and gives information about the fatty acid profile in two min. The 14:0, 16:0, 18:0, 18:1 and 18:2 fatty acids can be determined with excellent precision and other fatty acids with good precision according to the Shenk criteria, R ²≥0.90, SEP=1–1.5 SEL and R ²=0.70-0.89, SEP=2–3 SEL, respectively. The results obtained with the proposed method were compared with those provided by the conventional method based on GC-MS. At 95% significance level, the differences between the values obtained for the different fatty acids were within the experimental error. Electronic Supplementary Material Supplementary material is available for this article at and is accessible for authorized users.     

Separation of resin acids from fatty acids in relation to environmental studies.

Kraft mills pulping coniferous wood species discharge to their receiving waters effluents containing mixed resin and fatty acids. To study the fish-toxic properties of these fractions it is desirable to be able to separate them without causing double bond isomerizations in the acid-labile resin acid fraction. A method is described using toluenesulphonic acid as catalyst under very mild conditions and four examples of its application are given. It was not possible to separate tall oil samples without a low degree of resin acid isomerization.     

Stable carbon isotope ratios of methyl-branched fatty acids are different to those of straight-chain fatty acids in dairy products

Methyl-branched fatty acids (MBFAs) are the dominant form of fatty acid found in many bacteria. They are also found at low levels in a range of foodstuffs, where their presence has been linked to bacterial sources. In this study we evaluated the potential of compound-specific isotope analysis to obtain insights into the stable carbon isotope ratios (δ¹³C values in ‰) of individual MBFAs and to compare them to the stable carbon isotope ratios of straight-chain fatty acids in food. Due to their low abundance in foodstuffs, the MBFAs were enriched prior to gas chromatography coupled to isotope ratio mass spectrometric (GC–IRMS) analysis. After transesterification, urea complexation was used to suppress the 16:0 and 18:0 methyl esters that were dominant in the samples. Following that, silver-ion high performance liquid chromatography was used to separate the saturated from the unsaturated fatty acids. The resulting solutions of saturated fatty acids obtained from suet, goat’s milk, butter, and human milk were studied by GC–IRMS. The δ¹³C values of fatty acids with 12–17 carbons ranged from −25.4‰ to −37.6‰. In all samples, MBFAs were most depleted in carbon-13, followed by the odd-chain fatty acids 15:0 and 17:0. 14:0 and 16:0 contained the highest proportions of carbon-13. The results from this study illustrate that MBFAs have distinctive δ¹³C values and must originate from other sources and/or from very different substrates. These measurements support the initial hypothesis that δ¹³C values can be used to attribute MBFAs to particular sources.     

Determination of tetracycline antibiotics in fatty food samples by selective pressurized liquid extraction coupled with high‐performance liquid chromatography and tandem mass spectrometry

For the determination of trace residues of tetracycline antibiotics in fatty food samples, selective pressurized liquid extraction coupled with high‐performance liquid chromatography and tandem mass spectrometry was applied in this study. Copper(II) isonicotinate was first used as online cleanup adsorbent in the selective pressurized liquid extraction process. The adsorbent to sample ratio, extraction temperature, extraction time, and recycle times, etc. were optimized. The tetracyclines in food samples of pork, chicken meat, and clam meat were detected by liquid chromatography with tandem mass spectrometry. Tetracycline was found at levels of 0.32 and 0.53 μg/g and oxytetracycline was found at 0.14 and 0.21 μg/g in chicken meat and clam meat, respectively, while chlorotetracycline and deoxytetracycline were below the detection limit. The detection limit (S/N = 3) for these four tetracyclines were from 0.2 to 3.3 ng/g, the recoveries were from 75.8 to 110.5%, and relative standard deviations were from 5.5 to 13.6%. Copper(II) isonicotinate showed a higher purification capacity than other cleanup adsorbents for extraction of antibiotics in fatty food and the recovery showed predominance compared with a pressurized liquid extraction method without adsorbent. The study demonstrated that copper(II) isonicotinate would be a promising cleanup adsorbent in pressurized liquid extraction for the analysis of trace organic pollutants in complicated samples.     

Simultaneous analysis of select pharmaceuticals and personal care products in fish tissue using pressurized liquid extraction combined with silica gel cleanup

Analytical improvements were developed and validated for measuring select personal care products (PCPs) and two pharmaceuticals in fish tissue. The method was validated using fortified fillet tissue for twelve PCPs including fragrance materials, alkylphenols, photo initiators, and triclosan as well as two pharmaceuticals including carbamazepine (anti-seizure) and diazepam (anti-convulsant). The analytical method utilized pressurized liquid extraction (PLE) combined with silica gel cleanup, gel permeation chromatography, and gas chromatography ion-trap tandem mass spectrometry. Silica gel cleanup was combined with the PLE to produce one automated extraction/cleanup technique. This analytical improvement served to reduce the incurred cost, time, and loss of potential target analytes associated with independent cleanup steps. The combined extraction/cleanup technique resulted in an average increase of 10% in analyte recoveries. Average triplicate recoveries and relative standard deviations for the entire method, using 2.5 g of fish fillet tissue, were 92 ± 9% (recoveries ranged from 64 to 131%). The sensitivity of the analytical methods was improved by optimizing the resonant collision induced dissociation energy to the hundredths place (0.01 V). Improvements in ion production range from 24 to 122% for six of the 12 PCPs. Statistically derived method detection limits (MDLs) were also lowered on average by a factor of 8 and ranged from 1.2 to 38 ng/g wet weight. MDLs for carbamazepine and diazepam were 18 and 3.7 ng/g wet weight, respectively. Galaxolide and tonalide were measured in an environmental sample at concentrations of 81 and 5.5 ng/g wet weight, respectively.     

Confirmatory and quantitative analysis of fatty acid esters of hydroxy fatty acids in serum by solid phase extraction coupled to liquid chromatography tandem mass spectrometry

A novel class of endogenous mammalian lipids endowed with antidiabetic and anti-inflammatory properties has been recently discovered. These are fatty acid esters of hydroxy fatty acids (FAHFAs) formed by condensation between a hydroxy fatty acid and a fatty acid. FAHFAs are present in human serum and tissues at low nanomolar concentrations. Therefore, high sensitivity and selectivity profiling analysis of these compounds in clinical samples is demanded. An automated qualitative and quantitative method based on on-line coupling between solid phase extraction and liquid chromatography–tandem mass spectrometry has been here developed for determination of FAHFAs in serum with the required sensitivity and selectivity. Matrix effects were evaluated by preparation of calibration models in serum and methanol. Recovery factors ranged between 73.8 and 100% in serum. The within-day variability ranged from 7.1 to 13.8%, and the between-days variability varied from 9.3 to 21.6%, which are quite acceptable values taking into account the low concentration levels at which the target analytes are found. The method has been applied to a cohort of human serum samples to estimate the concentrations profiles as a function of the glycaemic state and obesity. Statistical analysis revealed three FAHFAs with levels significantly different depending on the glycaemic state or the body mass index. This automated method could be implemented in high-throughput analysis with minimum user assistance.