400nm高性能紫光LED的制作与表征(英文)

利用金属有机物化学气相沉积技术在蓝宝石衬底表面制备了带有p-AlGaN电子阻挡层的400 nm高性能紫光InGaN多量子阱发光二极管。制作了3种紫光LED,分别带有不同p-AlGaN电子阻挡层结构:Al摩尔分数为9%的p-AlGaN电子阻挡层;Al摩尔分数为11%的p-AlGaN电子阻挡层;Al摩尔分数为20%的10对p-AlGaN/GaN超晶格电子阻挡层。带有高浓度Al电子阻挡层的紫光LED的光输出功率高于低浓度Al电子阻挡层的紫光LED。带有10对p-AlGaN/GaN超晶格电子阻挡层的紫光LED的光输出功率获得了极大的提高,在20 mA注入电流时测试得到的光输出功率为21 mW。此外,该LED同时显示了在高注入电流下接近线性的I-L特性曲线和在LED芯片表面均匀的发光强度分布。     

p-AlGaN电子阻挡层Al组分对Si衬底绿光LED性能影响的研究

在Si(111)衬底上利用MOCVD方法生长了具有不同Al组分p-AlGaN电子阻挡层的绿光InGaN/GaN LED结构,并对其光电性能进行了研究.结果表明,不同Al组分样品的量子效率随电流密度的变化规律呈现多样性.在很低电流密度范围,LED量子效率随Al组分升高而下降;在较高电流密度范围,LED量子效率随Al组分升高而升高,即此时缓解了量子效率随电流密度增大而衰退的速率(即droop效应);但随着电流密度的进一步升高,反而加快了量子效率衰退的速率.这些现象解释为不同Al组分的p-AlGaN对空穴和电子 关键词： 氮化镓 p-AlGaN 绿光LED 量子效率     

新型电子阻挡层结构对蓝光InGaN发光二极管性能的提高

分别对3种不种电子阻挡层的蓝光AlGaN LED进行数值模拟研究。3种阻挡层结构分别为传统AlGaN电子阻挡层,AlGaN-GaN-AlGaN电子阻挡层和Al组分渐变的AlGaN-GaN-AlGaN电子阻挡层。此外对这对三种器件的活性区的载流子浓度、能带图、静电场和内量子效率进行比较和分析。研究结果表明,相较于传统AlGaN和AlGaN-GaN-AlGaN两种电子阻挡层的LED,具有Al组分渐变的AlGaN-GaN-AlGaN电子阻挡层结构的LED具有较高的空穴注入效率、较低的电子外溢现象和较小的静电场(活性区)。同时,具有Al组分渐变的AlGaN-GaN-AlGaN电子阻挡层结构的LED的efficiency droop现象也得到一定的缓解。     

量子阱层和垒层具有不同Al组分的270/290/330nm AlGaN基深紫外LED光电性能

为了研究AlGaN量子阱层和垒层中Al组分不同对AlGaN基深紫外发光二极管(LED)光电性能的影响,本文利用MOCVD生长、光刻和干法刻蚀工艺制备了AlGaN量子阱层和垒层具有不同Al组分的270/290/330nm深紫外LED,通过实验和数值模拟计算方法发现,量子阱层和垒层中具有低Al组分紫外LED的AlGaN材料具有较低的位错密度、较高的光输出功率和外量子效率。通过电流-电压(I-V)曲线拟合出的较大的理想因子(3.5)和能带结构图表明,AlGaN深紫外LED的电流产生是隧穿机制占据主导作用,这是因为高Al组分AlGaN量子阱中强极化场造成了有源层区域较大的能带弯曲和电势降。     

三明治结构电子阻挡层中势阱深度对LED性能的影响

在LED中引入了Al0.1Ga0.9N-Al x Ga1-x N-Al0.1Ga0.9N多层电子阻挡层,并讨论结构中插入的势阱深度(即中间层Al x Ga1-x N的Al组分"x")的变化对LED性能带来的影响。研究发现,具有三明治结构电子阻挡层(EBL)的LED比传统LED具有更好的发光特性,并且其性能与电子阻挡层中的势阱深度密切相关。究其原因,一是由于电子阻挡层内部不同程度的晶格失配而引入的极化电场引起了电子阻挡层的有效势垒高度的不同;二是在于电子阻挡层中的势阱所产生的空穴聚集效应也会随着势阱深度的变化而变化。故而使得空穴注入效率和电子阻挡层对电子的限制作用在不同势阱深度的LED样品中有所不同。     

背势垒层结构对AlGaN/GaN双异质结载流子分布特性的影响

首先通过一维自洽求解薛定谔/泊松方程,研究了AlGaN/GaN双异质结构中AlGaN背势垒层Al组分和厚度对载流子分布特性的影响.其次利用低压MOCVD方法在蓝宝石衬底上生长出具有不同背势垒层的AlGaN/GaN双异质结构材料,通过汞探针CV测试验证了理论计算的正确性.理论计算和实验结果均表明,随着背势垒层Al组分的提高和厚度的增加,主沟道中的二维电子气面密度逐渐减小,寄生沟道的二维电子气密度逐渐增加;背势垒层Al组分的提高和厚度的增加能有效的增强主沟道的二维电子气限域性,但是却带来了较高的 关键词： AlGaN/GaN 双异质结构 限域性 寄生沟道     

量子垒高度对深紫外LED调制带宽的影响

AlGaN基深紫外LED由于具有高调制带宽和小芯片尺寸,在紫外光通信领域受到越来越多的关注.本研究通过改变生长AlGaN量子垒层的Al源流量,生长了三种具有不同量子垒高度的深紫外LED,研究了量子垒高度对深紫外LED光电特性和调制特性的影响.研究发现,随着量子垒高度的增加,深紫外LED的光功率出现先增加后减小的趋势,量...     

反对称n-AlGaN层对GaN基双蓝光波长发光二极管性能的影响

采用数值分析方法对在InGaN/GaN混合多量子阱活性层和n-GaN之间引入n-AlGaN层的GaN基双蓝光波长发光二极管进行模拟分析.结果发现,与传统的具有p-AlGaN电子阻挡层的双蓝光波长发光二极管相比,这种反对称n-AlGaN层能有效改善电子和空穴在混合多量子阱活性层中的分布均匀性及减少电子溢出,实现电子空穴在各个量子阱中的平衡辐射,从而减弱了双蓝光波长发光二极管的效率衰减.此外,通过改变Al组分可以提高双蓝光波长发光二极管发射光谱的稳定性:当Al组分为0.16时,双蓝光波长发光二极管的光谱在小电流下比较稳定,而Al组分为0.12时,光谱在大电流下比较稳定.     

使用AlN/GaN超晶格势垒层生长高Al组分AlGaN/GaN HEMT结构

在蓝宝石衬底上生长了以AlN/GaN超晶格准AlGaN合金作为势垒的HEMT结构材料,并与传统AlGaN合金势垒样品进行了对比.在高Al组分(≥40%)情况下,超晶格势垒样品的表面形貌明显改进,电学性能特别是2DEG面电子浓度也有所改进.对超晶格势垒生长参数进行了初步优化,使得HEMT结构薄层电阻进一步降低,最后获得了251 Ω/□的薄层电阻. 关键词： AlGaN/GaN 结构 AlN/GaN超晶格 二维电子气 高电子迁移率晶体管     

AlGaN/GaN异质结载流子面密度测量的比较与分析

对MOCVD技术在蓝宝石衬底上生长的不同Al组分AlGaN/GaN异质结进行了范德堡法Hall测量和电容-电压(C-V)测量，发现Hall测量载流子面密度值大于C-V测量值，并且随着AlGaN层Al组分的增加，两种测量值都在增加，同时它们的差值也在增加.认为产生这一结果的原因有两方面.一方面，Ni/Au肖特基金属淀积在AlGaN/GaN异质结上，改变了AlGaN势垒层的表面状态，使得一部分二维电子气(2DEG)电子被抽取到空的施主表面态中，从而减小了AlGaN/GaN异质结界面势阱中的2DEG浓度.随着势垒层Al组分的增加，AlGaN层产生了更多的表面态，从而使得更多的电子被抽取到了空的表面态中.另一方面，由于C-V测量本身精确度受到串联电阻的影响，使得测量电容小于实际电容，从而低估了载流子浓度.     

Improved color rendering of phosphor-converted white light-emitting diodes with dual-blue active layers and n-type AlGaN layer

An InGaN/GaN blue light-emitting diode (LED) structure and an InGaN/GaN blue-violet LED structure were grown sequentially on the same sapphire substrate by metal-organic chemical vapor deposition. It was found that the insertion of an n-type AlGaN layer below the dual blue-emitting active layers showed better spectral stability at the different driving current relative to the traditional p-type AlGaN electron-blocking layer. In addition, color rendering index of a Y3Al5O12:Ce3+ phosphor-converted white LED based on a dual blue-emitting chip with n-type AlGaN reached 91 at 20 mA, and Commission Internationale de L'Eclairage coordinates almost remained at the same point from 5 to 60 mA.     

Performance enhancement of an InGaN light-emitting diode with an AlGaN/InGaN superlattice electron-blocking layer

The efficiency enhancement of an InGaN light-emitting diode(LED) with an AlGaN/InGaN superlattice(SL)electron-blocking layer(EBL) is studied numerically,which involves the light-current performance curve,internal quantum efficiency electrostatic field band wavefunction,energy band diagram carrier concentration,electron current density,and radiative recombination rate.The simulation results indicate that the LED with an AlGaN/InGaN SL EBL has better optical performance than the LED with a conventional rectangular AlGaN EBL or a normal AlGaN/GaN SL EBL because of the appropriately modified energy band diagram,which is favorable for the injection of holes and confinement of electrons.Additionally,the efficiency droop of the LED with an AlGaN/InGaN SL EBL is markedly improved by reducing the polarization field in the active region.     

A dual-blue light-emitting diode based on strain-compensated InGaN-AlGaN/GaN quantum wells

A strain-compensated InGaN quantum well(QW) active region employing a tensile AlGaN barrier is analyzed.Its spectral stability and efficiency droop for a dual-blue light-emitting diode(LED) are improved compared with those of the conventional InGaN/GaN QW dual-blue LEDs based on a stacking structure of two In0.18Ga0.82N/GaN QWs and two In0.12Ga0.88N/GaN QWs on the same sapphire substrate.It is found that the optimal performance is achieved when the Al composition of the strain-compensated AlGaN layer is 0.12 in blue QW and 0.21 in blue-violet QW.The improvement performance can be attributed to the strain-compensated InGaN-AlGaN/GaN QW,which can provide a better carrier confinement and effectively reduce leakage current.     

硅衬底氮化镓基LED薄膜转移至柔性黏结层基板后其应力及发光性能变化的研究

本文将硅(Si)衬底上外延生长的氮化镓(GaN)基发光二极管(LED)薄膜转移至含有柔性黏结层的基板上, 获得了不受衬底和支撑基板束缚的LED薄膜. 利用高分辨率X射线衍射仪(HRXRD)研究了薄膜转移前后的应力变化, 同时对其光致发光(PL)光谱的特性进行了研究. 结果表明: 硅衬底GaN基LED薄膜转移至柔性基板后, GaN受到的应力会由转移前巨大的张应力变为转移后微小的压应力, InGaN/GaN量子阱受到的压应力则增大; 尽管LED薄膜室温无损转移至柔性基板其InGaN阱层的In组分不会改变, 然而按照HRXRD倒易空间图谱通用计算方法会得出平均铟组发生了变化; GaN基LED薄膜从外延片转移至柔性基板时其PL谱会发生明显红移.     

阶梯AlGaN外延新型Al_(0.25)Ga_(0.75)N/GaNHEMTs击穿特性分析

为了优化AlGaN/GaN HEMTs器件表面电场,提高击穿电压,本文首次提出了一种新型阶梯AlGaN/GaN HEMTs结构.新结构利用AlGaN/GaN异质结形成的2DEG浓度随外延AlGaN层厚度降低而减小的规律,通过减薄靠近栅边缘外延的AlGaN层,使沟道2DEG浓度分区,形成栅边缘低浓度2DEG区,低的2DEG使阶梯AlGaN交界出现新的电场峰,新电场峰的出现有效降低了栅边缘的高峰电场,优化了AlGaN/GaN HEMTs器件的表面电场分布,使器件击穿电压从传统结构的446 V,提高到新结构的640 V.为了获得与实际测试结果一致的击穿曲线,本文在GaN缓冲层中设定了一定浓度的受主型缺陷,通过仿真分析验证了国际上外延GaN缓冲层时掺入受主型离子的原因,并通过仿真分析获得了与实际测试结果一致的击穿曲线.     

Dual-blue light-emitting diode based on strain-compensated InGaN-AlGaN/GaN quantum wells

Strain-compensated InGaN quantum well (QW) active region employing tensile AlGaN barrier is analyzed. Its spectral stability and efficiency droop for dual-blue light-emitting diode (LED) are improved compared with those of the conventional InGaN/GaN QW dual-blue LED based on stacking structure of two In_0.18Ga_0.82N/GaN QWs and two In_0.12Ga_0.88N/GaN QWs on the same sapphire substrate. It is found that the optimal performance is achieved when the Al composition of strain-compensated AlGaN layer is 0.12 in blue QW and 0.21 in blue-violet QW. The improvement performance can be attributed to the strain-compensated InGaN-AlGaN/GaN QW that can provide a better carrier confinement and effectively reduce leakage current.     

Enhanced carrier injection in InGaN/GaN multiple quantum wells LED with polarization-induced electron blocking barrier

In this report, we designed a light emitting diode (LED) structure in which an N-polar p-GaN layer is grown on top of Ga-polar In_0.1Ga_0.9N/GaN quantum wells (QWs) on an n-GaN layer. Numerical simulation reveals that the large polarization field at the polarity inversion interface induces a potential barrier in the conduction band, which can block electron overflow out of the QWs. Compared with a conventional LED structure with an Al_0.2Ga_0.8N electron blocking layer (EBL), the proposed LED structure shows much lower electron current leakage, higher hole injection, and a significant improvement in the internal quantum efficiency (IQE). These results suggest that the polarization induced barrier (PIB) is more effective than the AlGaN EBL in suppressing electron overflow and improving hole transport in GaN-based LEDs.     

Photoreflectance investigations of AlGaN/GaN heterostructures with a two dimensional electron gas

Undoped AlGaN/GaN heterostructures with different content and thickness of AlGaN layer are investigated by photoreflectance (PR) spectroscopy. We have observed PR resonances related to an absorption in both GaN and AlGaN layers. The character of these resonances has been analyzed, and PR lines associated with excitonic and band-to-band absorption in the GaN layer and band-to-band absorption in the AlGaN layer have been identified. The transition related to band-to-band absorption possesses characteristic Franz–Keldysh oscillations (FKOs) associated with a built-in electric field. The electric field in the AlGaN layer obtained on the basis of the analysis of FKOs has been found to be in the range of 244–341 kV/cm. The value of the field has been found to decrease with the increase in AlGaN thickness and to increase with the increase in Al concentration. The surface potential for AlGaN layers has been found to increase with the increase in Al mole fraction and has been estimated to be in the range of 1.0–1.7 eV.