Preparation and characterization of polybenzimidazole membranes prepared by gelation in phosphoric acid

Phosphoric acid doped poly (2, 2′‐(m‐phenylene)‐5, 5′‐bibenzimidazole) (PBI) membranes were prepared by dissolving PBI powders in 85% phosphoric acid at 190–200°C and then promoting gelation of the PBI by cooling the solutions to ?18°C. The extent of acid doping of the PBI membranes was controlled by immersing the membrane in aqueous phosphoric acid solutions of different concentrations (acid de‐doping). The process of the acid de‐doping was faster than acid doping of membrane cast from N,N‐dimethylacetamide (DMAc). The de‐doping process caused shrinkage of the PBI membrane and thus an increase in the membrane strength due to the packing of PBI chains according to the X‐ray diffraction analysis. The tensile stress and proton conductivity of the obtained PBI membranes with different acid doping levels were measured. For a PBI (η_IV: 0.58 dL · g^?1) membrane with an acid doping level of 7.0 (molar number of doped acid per mole repeat unit of PBI), the stress at break and proton conductivity at 120°C without humidification were 2.6 MPa and 5.1 × 10^?2 S · cm^?1, respectively. These results were comparable to those of the membranes cast from PBI solutions in DMAc. Copyright © 2009 John Wiley & Sons, Ltd.     

Polybenzimidazoles tethered with N‐phenyl 1,2,4‐triazole units as polymer electrolytes for fuel cells

Polybenzimidazole (PBI) polymers tethered with N‐phenyl 1,2,4‐triazole (NPT) groups were prepared from a newly synthesized aromatic diacid, 3′‐(4‐phenyl‐4H‐1,2,4‐triazole‐3,5‐diyl) dibenzoic acid (PTDBA). The obtained polymers show superior thermal and chemical stability and good solubility in many aprotic solvents. The inherent viscosities of all polymers were around 1 dL/g. They exhibit high thermal stability with initial decomposition temperature ranging from 515 to 530 °C, high glass transition temperature ranging from 375 to 410 °C, and good mechanical properties with tensile stress in the range of 66–98 MPa and modulus 1897–2600 MPa. XRD analysis indicates that these polymers are amorphous in nature. Physicochemical properties such as water and phosphoric acid‐uptake, oxidative stability, and proton conductivity of membranes of these polymers have also been determined. The proton conductivity ranged from 4.7 × 10^?3 to 1.8 × 10^?2 S cm^?1 at 175 °C in dry conditions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2289–2303, 2009     

Synthesis and characterization of fluorine‐containing polybenzimidazole for proton conducting membranes in fuel cells

Two new kinds of fluorine‐containing polybenzimidazoles (PBI), poly(2,2′‐(tetrafluoro‐p‐phenylene)‐5,5′‐bibenzimidazole) and poly(2,2′‐tetradecafluoroheptylene‐5,5′‐bibenzimidazole), were synthesized by condensation polymerization of 3,3′‐diaminobenzidine and perfluoroterephthalic acid (or perfluoroazelaic acid), with polyphosphoric acid as solvent. Thermogravimetric analysis results show that the fluorine‐containing polymers synthesized exhibit promising thermal stability. The film‐forming properties of the fluorine‐containing polymers are improved over nonfluorinated PBI. The introduction of fluorine into the backbone of the polymers has significant positive affection on their chemical oxidation stability demonstrated by Fenton test. Compared with poly(2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole)/phosphoric acid (PA) composite membrane, the resulting fluorinated membranes with a same PA doping level exhibit better flexibility and higher proton conductivity. The maximum proton conductivity gained is 3.05 × 10^?2 S/cm at 150 °C with a PA doping level of 7. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2115–2122, 2010     

In Situ Synthesis of Polybenzimidazole on the Surface of Single Wall Carbon Nanotubes

Single wall carbon nanotube (SWNT) was carboxylated to introduce –OH, –COOH, and –NH₂ on the surfaces, which made it possible for polybenzimidazole (PBI) to be in situ synthesized. The resulting SWNT doped PBI (SWNT/PBI) was characterized by Fourier transform infrared spectroscopy thermogravimetric analysis. The conductivity of membrane casting from PBI/N,N-dimethylacetamide (DMAc) and SWNT/PBI/DMAc solution was also investigated. Owing to the incorporation of SWNT, the SWNT/PBI membranes achieve a maximum conductivity of 3.70 × 10^?4 Ω.cm^?1 at 200°C.     

Guest‐Assisted Proton Conduction in the Sulfonic Mesoporous MIL‐101 MOF

Post‐synthesis modification of MIL‐101(Cr)‐NO₂ was explored in order to decorate the organic backbone by propyl‐sulfonic groups, with the aim to incorporate mobile and acidic protons for solid‐state proton electrolyte applications. The resulting solid switched from insulating towards proton superconductive behavior under humidity, while the conductivity recorded at 363 K and 95 % relative humidity reached 4.8×10^?3 S cm^?1. Propitiously, the impregnation of the material by strong acidic molecules (H₂SO₄) further boosted the proton conductivity performances up to the remarkable σ value of 1.3×10^?1 S cm^?1 at 363 K/95 % RH, which reaches the performances of the best proton conductive MOF reported so far.     

Water‐Stable Homochiral Cluster Organic Frameworks Built by Two Kinds of Large Tetrahedral Cluster Units

Compared with metal organic frameworks (MOFs), the proton conductivity of cluster organic frameworks has been less studied. Herein, two supertetrahedral cluster organic frameworks (SCOFs) have been made that show two‐fold interpenetrated networks built by trivalent lanthanide tetrahedral clusters and monovalent cuprous T₃‐supertetrahedral clusters. The structure analysis, second harmonic generation signals, and solid‐state circular dichroism spectroscopy consistently reveal the chirality of these SCOFs. Remarkably, the water‐stable SCOFs show a high proton conductivity value of 1.4×10^?3 S cm^?1 at 80 °C and 95 % RH (relative humidity).     

Thermally Stable Super Ionic Conductor from Carbon Sphere Oxide

A highly stable proton conductor has been developed from carbon sphere oxide (CSO). Carbon sphere (CS) generated from sucrose was oxidized successfully to CSO using Hummers’ graphite oxidation technique. At room temperature and 90 % relative humidity, the proton conductivity of thin layer CSO on microsized comb electrode was found to be 8.7×10^?3 S cm^?1, which is higher than that for a similar graphene oxide (GO) sample (3.4×10^?3 S cm^?1). The activation energy (E_a) of 0.258 eV suggests that the proton is conducted through the Grotthuss mechanism. The carboxyl functional groups on the CSO surface are primarily responsible for transporting protons. In contrast to conventional carbon‐based proton conductors, in which the functional groups decompose around 80 °C, CSO has a stable morphology and functional groups with reproducible proton conductivity up to 400 °C. Even once annealed at different temperatures at high relative humidity, the proton conductivity of CSO remains almost unchanged, whereas significant change is seen with a similar GO sample. After annealing at 100 and 200 °C, the respective proton conductivity of CSO was almost the same, and was about ～50 % of the proton conductivity at room temperature. Carbon‐based solid electrolyte with such high thermal stability and reproducible proton conductivity is desired for practical applications. We expect that a CSO‐based proton conductor would be applicable for fuel cells and sensing devices operating under high temperatures.     

Synthesis of sulfonated poly(imidoaryl ether sulfone) membranes for polymer electrolyte membrane fuel cells

New sulfonated poly(imidoaryl ether sulfone) copolymers derived from sulfonated 4,4′‐dichlorodiphenyl sulfone, 4,4′‐dichlorodiphenyl sulfone, and imidoaryl biphenol were evaluated as polymer electrolyte membranes for direct methanol fuel cells. The sulfonated membranes were characterized with Fourier transform infrared spectroscopy, thermogravimetric analysis, and proton nuclear magnetic resonance spectra. The state of water in the membranes was measured with differential scanning calorimetry, and the existence of free water and bound water was discussed in terms of the sulfonation level. The 10 wt % weight loss temperatures of these copolymers were above 470 °C, indicating excellent thermooxidative stability to meet the severe criteria of harsh fuel‐cell conditions. The proton conductivities of the membranes ranged from 3.8 × 10^?2 to 5 × 10^?2 S/cm at 90 °C, depending on the degree of sulfonation. The sulfonated membranes maintained the original proton conductivity even after a boiling water test, and this indicated the excellent hydrolytic stability of the membranes. The methanol permeabilities ranged from 1.65 × 10^?8 to 5.14 × 10^?8 cm²/s and were lower than those of other conventional sulfonated ionomer membranes, particularly commercial perfluorinated sulfonated ionomer (Nafion). The properties of proton and methanol transport were discussed with respect to the state of water in the membranes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5620–5631, 2005     

Structural modification of chitosan biopolymer as a novel polyelectrolyte membrane for green power generation

In the present study, a series of bioresource polyelectrolytes based on chitosan were synthesized and assessed for applicability in direct methanol fuel cells (DMFCs). A binary cross‐linking agent (sulfosuccinic acid/glutaraldehyde) was used for the structural modification of chitosan and membranes comprising various amounts of sulfosuccinic acid (0, 8, 12, and 16 wt% SSA/wt chitosan) were prepared. It was found that by increasing the sulfonate groups' content up to 16 wt%, proton conductivity and methanol permeability properties reach the values of 0.0452 S cm^?1 and 9.6 × 10^?7 cm² sec^?1, respectively. Based on the membrane selectivity evaluation and activation energy measurements of proton conduction, the optimum composition of cross‐linking agent was determined. The optimum composition resulted in a relatively high proton conductivity of 0.0452 S cm^?1 and a low methanol permeability of 9.6 × 10^?7 cm² sec^?1. Moreover, the optimum proton exchange membrane exhibited selectivity value of 47,100 in comparison with the corresponding value of 40,500 for Nafion® 117. The fabricated membranes showed acceptable oxidative and hydrolytic stability. Furthermore, single cell DMFC performance test revealed a power density of 17 mW cm^?2 at 30°C and 41 mW cm^?2 at 60°C in a 2 M methanol feed. Hence, prepared proton‐conducting bioresource ionomers could have promising potential in the field of green power generation as a low cost and biodegradable polyelectrolyte. Copyright © 2009 John Wiley & Sons, Ltd.     

Sulfonated polybenzimidazoles: Proton conduction and acid–base crosslinking

A series of soluble, benzimidazole‐based polymers containing sulfonic acid groups (SuPBI) has been synthesized. SuPBI membranes resist extensive swelling in water but are poor proton conductors. When blended with high ion exchange capacity (IEC) sulfonated poly(ether ether ketone) (SPEEK), a polymer that has high proton conductivity but poor mechanical integrity, ionic crosslinks form reducing the extent of swelling. The effect of sulfonation of PBI on crosslinking in these blends was gauged through comparison with nonsulfonated analogs. Sulfonic acid groups present in SuPBI compensate for acid groups involved in crosslinking, thereby increasing IEC and proton conductivity of the membrane. When water uptake and proton conductivity were compared to the IEC of blends containing either sulfonated or nonsulfonated PBI, no noticeable distinction between PBI types could be made. Comparisons were also made between these blends and pure SPEEK membranes of similar IEC. Blend membranes exhibit slightly lower maximum proton conductivity than pure SPEEK membranes (60 vs. 75 mS cm^?1) but had significantly enhanced dimensional stability upon immersion in water, especially at elevated temperature (80 °C). Elevated temperature measurements in humid environments show increased proton conductivity of the SuPBI membranes when compared with SPEEK‐only membranes of similar IEC (c.f. 55 for the blend vs. 42 mS cm^?1 for SPEEK at 80 °C, 90% relative humidity). © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3640–3650, 2010     

Highly phosphonated poly(N‐phenylacrylamide) for proton exchange membranes

A novel highly phosphonated poly(N‐phenylacrylamide) ( PDPAA ) with an ion‐exchange capacity (IEC) of 6.72 mequiv/g was synthesized by the radical polymerization of N‐[2,4‐bis(diethoxyphosphinoyl)phenyl]acrylamide ( DEPAA ), followed by the hydrolysis with trimethylsilyl bromide. Then, the crosslinked PDPAA membrane was successfully prepared by the electrophilic substitution reaction between the aromatic rings of PDPAA and the carbocation formed from hexamethoxymethylmelamine (CYMEL) as a crosslinker in the presence of methanesulfonic acid. The crosslinked PDPAA membrane had high oxidative stability against Fenton's reagent at room temperature. The proton conductivity of the crosslinked PDPAA membrane was 8.8 × 10^?2 S/cm at 95% relative humidity (RH) and 80 °C, which was comparable to Nafion 112. Under low RH, the crosslinked PDPAA membrane showed the proton conductivity of 1.9 × 10^?3 and 4.7 × 10^?5 S/cm at 50 and 30% RH, respectively. The proton conductivity of the crosslinked PDPAA membrane lied in the highest class among the reported phosphonated polymers, and, consequently, the very high local concentration of the acids of PDPAA (IEC = 6.72 mequiv/g) achieved high and effective proton conduction under high RH. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Doping phosphoric acid in polybenzimidazole membranes for high temperature proton exchange membrane fuel cells

Polybenzimidazole (PBI) membranes were doped in phosphoric acid solutions of different concentrations at room temperature. The doping chemistry was studied using the Scatchard method. The energy distribution of the acid complexation in polymer membranes is heterogeneous, that is, there are two different types of sites in PBI for the acid doping. The protonation constants of PBI by phosphoric acid are found to be 12.7 L mol^?1 (K¹) for acid complexing sites with higher affinity, and 0.19 L mol^?1 (K²) for the sites with lower affinity. The dissociation constants for the complexing acid onto these two types of PBI sites are found to be 5.4 × 10^?4 and 3.6 × 10^?2, respectively, that is, about 10 times smaller than that of aqueous phosphoric acid in the first case but 5 times higher in the second. The proton conducting mechanism is also discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2989–2997, 2007     

Hydrogen‐Bonded Organic Frameworks (HOFs): A New Class of Porous Crystalline Proton‐Conducting Materials

Two porous hydrogen‐bonded organic frameworks (HOFs) based on arene sulfonates and guanidinium ions are reported. As a result of the presence of ionic backbones appended with protonic source, the compounds exhibit ultra‐high proton conduction values (σ) 0.75× 10^?2 S cm^?1 and 1.8×10^?2 S cm^?1 under humidified conditions. Also, they have very low activation energy values and the highest proton conductivity at ambient conditions (low humidity and at moderate temperature) among porous crystalline materials, such as metal–organic frameworks (MOFs) and covalent organic frameworks (COFs). These values are not only comparable to the conventionally used proton exchange membranes, such as Nafion used in fuel cell technologies, but is also the highest value reported in organic‐based porous architectures. Notably, this report inaugurates the usage of crystalline hydrogen‐bonded porous organic frameworks as solid‐state proton conducting materials.     

Proton Conductivities of Graphene Oxide Nanosheets: Single,Multilayer, and Modified Nanosheets

Proton conductivities of layered solid electrolytes can be improved by minimizing strain along the conduction path. It is shown that the conductivities (σ) of multilayer graphene oxide (GO) films (assembled by the drop‐cast method) are larger than those of single‐layer GO (prepared by either the drop‐cast or the Langmuir‐Blodgett (LB) method). At 60 % relative humidity (RH), the σ value increases from 1×10^?6 S cm^?1 in single‐layer GO to 1×10^?4 and 4×10^?4 S cm^?1 for 60 and 200 nm thick multilayer films, respectively. A sudden decrease in conductivity was observed for with ethylenediamine (EDA) modified GO (enGO), which is due to the blocking of epoxy groups. This experiment confirmed that the epoxide groups are the major contributor to the efficient proton transport. Because of a gradual improvement of the conduction path and an increase in the water content, σ values increase with the thickness of the multilayer films. The reported methods might be applicable to the optimization of the proton conductivity in other layered solid electrolytes.     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Polycarboxylate‐Templated Coordination Polymers: Role of Templates for Superprotonic Conductivities of up to 10−1 S cm−1

Three coordination polymers (CPs) have been synthesized based on a [Co(bpy)(H₂O)₄]²⁺ chain (bpy=4,4′‐bipyridine) by a template approach. The frameworks are neutralized by different templated polycarboxylate anions (furan di‐carboxylate (fdc) in Co‐fdc, benzene tri‐carboxylate (btc) in Co‐tri and benzene tetra‐carboxylate (btec) in Co‐tetra). These templates with different degrees of protonation and ionic carrier concentration played significant role on crystal packing as well as formation of well‐directed H‐bonded networks which made these CPs perform well in proton conduction (PC). The PC value reaches to 1.49×10^?1 S cm^?1 under 80 °C and 98 % relative humidity (R.H.) for Co‐tri, which is the highest among CPs/MOFs/COFs and is an example of conductivity in the order of 10^?1 S cm^?1. Co‐tri and Co‐tetra are excellent proton conductors at mild temperature (40 °C) and 98 % R.H. (conductivities up to 2.92×10^?2 and 1.38×10^?2 S cm^?1, respectively).     

Proton‐Conducting Magnetic Coordination Polymers

Three isostructural lanthanide‐based two‐ dimensional coordination polymers (CPs) {[Ln₂(L)₃(H₂O)₂]_n ? 2n CH₃OH) ? 2n H₂O} (Ln=Gd³⁺ ( 1 ), Tb³⁺ ( 2 ), Dy³⁺ ( 3 ); H₂L=cyclobutane‐1,1‐dicarboxylic acid) were synthesized by using a low molecular weight dicarboxylate ligand and characterized. Single‐crystal structure analysis showed that in complexes 1 – 3 lanthanide centers are connected by μ₃‐bridging cyclobutanedicarboxylate ligands along the c axis to form a rod‐shaped infinite 1D coordination chain, which is further linked with nearby chains by μ₄‐connected cyclobutanedicarboxylate ligands to form 2D CPs in the bc plane. Viewing the packing of the complexes down the b axis reveals that the lattice methanol molecules are located in the interlayer space between the adjacent 2D layers and form H‐bonds with lattice and coordinated water molecules to form 1D chains. Magnetic properties of complexes 1 – 3 were thoroughly investigated. Complex 1 exhibits dominant ferromagnetic interaction between two nearby gadolinium centers and also acts as a cryogenic magnetic refrigerant having a significant magnetic entropy change of ?ΔS_m=32.8 J kg^?1 K^?1 for ΔH=7 T at 4 K (calculated from isothermal magnetization data). Complex 3 shows slow relaxation of magnetization below 10 K. Impedance analysis revealed that the complexes show humidity‐dependent proton conductivity (σ=1.5×10^?5 S cm^?1 for 1 , σ=2.07×10^?4 S cm^?1 for 2 , and σ=1.1×10^?3 S cm^?1 for 3 ) at elevated temperature (>75 °C). They retain the conductivity for up to 10 h at high temperature and high humidity. Furthermore, the proton conductivity results were correlated with the number of water molecules from the water‐vapor adsorption measurements. Water‐vapor adsorption studies showed hysteretic and two‐step water vapor adsorption (182000 μL g^?1 for 1 , 184000 μL g^?1 for 2 , and 1874000 μL g^?1 for 3 ) in the experimental pressure range. Simulation of water‐vapor adsorption by the Monte Carlo method (for 1 ) confirmed the high density of adsorbed water molecules, preferentially in the interlayer space between the 2D layers.     

Enhancing proton conductivity of proton exchange membrane with SPES nanofibers containing porous organic cage

Effective proton conducting sites and establishing proton channels are two critical factors in developing high‐performance proton exchange membranes. This study first establishes a strategy in designing effective proton conducting channels for Nafion by using solution blowing of sulfonated polyethersulfone (SPES) nanofibers containing CC3, which is an emerging porous organic cage that possesses the advantages of dissolvable organic solvents and high proton conduction from its interconnected three‐dimensional pore structure. Our strategy results in SPES nanofiber networks with CC3 uniformly involved in and composite membranes with Nafion‐filled interfiber voids. Benefiting from such structural features, the composite membrane exhibits high proton conductivity (0.315 S cm^?1 at 80°C and 100% RH), low methanol permeability (0.69 × 10^?7 cm² S^?1), excellent water absorption, thermal and dimensional stability, and single‐cell performance. This study provides not only a valuable reference for the application of CC3 but also a new idea for establishment of proton transfer channels.     

Superprotonic Conductivity of a UiO‐66 Framework Functionalized with Sulfonic Acid Groups by Facile Postsynthetic Oxidation

Facile postsynthetic oxidation of the thiol‐laced UiO‐66‐type framework UiO‐66(SH)₂ enabled the generation of UiO‐66(SO₃H)₂ with sulfonic acid groups covalently linked to the backbone of the system. The oxidized material exhibited a superprotonic conductivity of 8.4×10^?2 S cm^?1 at 80 °C and 90 % relative humidity, and long‐term stability of the conductivity was observed. This level of conductivity exceeds that of any proton‐conducting MOF reported to date and is equivalent to the conductivity of the most effective known electrolyte, Nafion.     

Structural Diversity in Multinuclear PdII Assemblies that Show Low‐Humidity Proton Conduction

Systematic investigation on synergetic effects of geometry, length, denticity, and asymmetry of donors was performed through the formation of a series of uncommon Pd^II aggregates by employing the donor in a multicomponent self‐assembly of a cis‐blocked 90° Pd^II acceptor and a tetratopic donor. Some of these assemblies represent the first examples of these types of structures, and their formation is not anticipated by only taking the geometry of the donor and the acceptor building units into account. Analysis of the crystal packing of the X‐ray structure revealed several H bonds between the counteranions (NO₃^?) and water molecules (O?H???O?N). Moreover, H‐bonded 3D‐networks of water are present in the molecular pockets, which show water‐adsorption properties with some variation in water affinity. Interestingly, these complexes exhibit proton conductivity (1.87×10^?5–6.52×10^?4 Scm^?1) at 296 K and low relative humidity (ca. 46 %) with activation energies of 0.29–0.46 eV. Moreover, the conductivities further increase with the enhancement of humidity. The ability of these assemblies to exhibit proton‐conducting properties under low‐humidity conditions makes these materials highly appealing as electrolytes in batteries and in fuel‐cell applications.