TiO2/Gd2O3纳米粉体的制备、表征及光催化活性

利用酸催化的溶胶-凝胶法制备了纯TiO₂和Gd³⁺(0.5wt%)掺杂的TiO₂纳米粉体，采用XRD、BET、XPS、紫外-可见漫反射谱(DRS)和表面光电压谱(SPS)等技术进行了表征；以亚甲基蓝(MB)的光催化降解为探针反应，评价了其光催化活性；探讨了Gd³⁺掺杂对TiO₂纳米粉体的光催化活性的影响机制。结果表明，TiO₂/Gd₂O₃纳米粒子对MB溶液的光催化活性提高到纯TiO₂的1.5倍。掺杂Gd³⁺可以强烈抑制TiO₂由锐钛矿相向金红石相的转变；阻碍TiO₂晶粒的生长；提高高温组织稳定性，改善粉体的表面织构特性；形成光生电子的浅势捕获陷阱，抑制e^-/h⁺复合，这些因素共同作用最终导致TiO₂/Gd₂O₃纳米粉体的光催化活性明显提高。XPS分析结果证实，掺杂Gd³⁺导致粉体的表面羟基含量降低。由于产生了量子尺寸效应，复合粉体的紫外吸收带边蓝移，光的吸收能力略有降低。     

碱土金属掺杂纳米TiO2催化剂的制备与光催化活性的评价

The nanometer TiO₂ were prepared by the hydrolyze-gel method and fellowed by doping alkaline-earth metals (Mg, Ca, Sr, Ba). XRD, SEM, diffuse reflection spectra were used to investigate their characteristices. The result indicates that the average particles size of the TiO₂ is about 80 nm and keep uniformity in distributing. The product was mainly anatase in 300～400 ℃ calcinations, the einstein shift of absorption spectrum was observed after doping the alkaline-earth metals. The best mole percentages of Mg, Ca, Sr and Ba are 0.5%, 1.0%, 1.5%, 1.5% respectively. Under the same reaction conditions, it is more effective to the UV-catalyed degradation reaction that the catalysts containing Mg and Ca were calcined at 300 ℃ for 1h or containing Sr and Ba were calcined at 400 ℃ for 1 h. The photocatalystic activity is considerably depondent on pH and the concentration of the oxidant. Using the sunlight to do the degradation experimental, the result also show that the doping catalysts has higher degradation efficiency than that of pure TiO₂.     

原位红外光谱法研究La/TiO2对有机污染物的光催化降解

本工作采用改进的溶胶-凝胶法和浸渍法制备了TiO₂掺杂稀土离子La³⁺的La/TiO₂光催化剂，运用XRD、N₂吸附脱附、紫外可见漫反射光谱(DRS)、表面光电压谱(SPS)等手段进行表征，同时利用原位红外技术考察了La/TiO₂样品光催化降解乙烯、丙酮、苯的气-固相光催化氧化反应，对其光催化降解有机污染物的过程进行了研究。结果表明，TiO₂经适量La³⁺掺杂后，锐钛矿晶型的含量增加，晶粒度减小，比表面积增大，禁带宽度增加，表面光电压信号增强，光生电子-空穴对有效分离；La/TiO₂样品对乙烯、丙酮、苯的光催化性能与纯TiO₂相比均有不同程度的改善，乙烯可以被光催化氧化完全矿化生成CO₂，而丙酮被光催化氧化可能生成中间产物丙酸，苯被光催化氧化可能生成中间产物苯酚和苯醌。     

掺杂Cu的TiO2纳米粒子的制备、表征及其光催化活性

采用Sol-gel法制备了纯的和掺杂不同量Cu的TiO2纳米粒子,并用TG-DTA,XRD,XPS,UV-Vis和荧光光谱对样品进行了表征,考察焙烧温度和Cu含量对TiO2纳米粒子的性质及光催化活性的影响,初步探讨了Cu的掺杂对TiO2相变的作用机制及样品荧光光谱与光催化活性的关系.结果表明,Cu2+的掺杂对TiO2的相变有很大的促进作用,并使其光谱响应范围向可见光区拓展.Cu的掺杂未引起新的荧光现象,但适量Cu的掺杂能够降低TiO2纳米粒子的荧光强度.此外,在光催化降解苯酚的实验中,于500℃处理的掺杂Cu的TiO2纳米粒子的光催化活性较高,与表征结果一致.而掺杂不同量Cu的TiO2的光催化活性顺序与样品荧光光谱强度的顺序相反,即荧光光谱强度越低,其光催化活性越高.     

N 掺杂TiO2光催化剂的制备及其可见光活性研究

A visible-light-active photocatalyst was prepared by calcination of the hydrolysis product of tetrabutyl titanate with ammonia as precipitant. The photocatalyst was characterized by X-ray diffraction (XRD), UV-Vis diffuse reflection spectra (DRS), thermal gravimetric-differential thermal analysis (TG-DTA), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM). The color of the photocatalyst was yellow and could absorb light wavelength under 550 nm as measured by DRS. The catalyst calcined at higher temperature will give lower absorbance for visible light. Structures of the sample were characterized mainly to be anatase by XRD except for the sample calcined at 700 ℃ which gave mixtures of anatase and rutile. TG-DTA results showed that temperature for anatase formation was 415 ℃. XPS results showed that doped-nitrogen was presented in the sample, they are important to show visible-light absorbency. The photocatalytic activities were evaluated using methyl orange and phenol as model pollutants, the results showed that over 90% of phenol could be degraded under visible light using N/TiO₂ as the catalyst after 4 hours reaction. Almost the same activity was found for the TiO₂ photocatalyst calcined at different temperature under sunlight but activities were different when the treatment was under UV light.     

TiO2纳米粒子制备方法对其光催化活性的影响

分别用胶溶法、金属醇盐水解法和低温水解法制备了TiO2纳米粒子;采用XRD和BET技术,测试了TiO2粒子的粒径、晶型及表面积。以庚烷的气相光催化氧化为探针反应,考察了不同方法、不同温度处理的TiO2粒子的光催化活性。结果表明,以胶溶法和金属醇盐水解法制备的TiO2粒子,随焙烧温度的增加TiO2粒子长大,晶型由锐钛矿向金红石型转变,光催化活性降低。用低温水解法,可在低温下制得金红石型TiO2粒子,但其催化活性很低。说明由原料和制备方法所决定的TiO2粒子的物理化学性质,影响其光催化行为。锐钛矿型TiO2粒子催化活性较金红石型TiO2好。这是由于前者的表面羟基含量较高且带隙能较大的缘故。     

稀土镧掺杂二氧化钛的光催化特性

二氧化钛有合适的禁带宽度,在光催化体系中有较好的稳定性,是一种较为理想的半导体光催化剂.近来,在太阳能转换和储存,二氧化碳还原,有害复杂有机物降解等方面都引起了广泛的研究兴趣.已有文献报导了不同的掺杂催化体系对其光催化性能的影响.Ｋａｋｕｔａ[1,2]等研究了二氧化钛复合氧化物体系的光催化性能.Ｃｈｏｉ[3]等系统地研究了过渡金属氧化物掺杂的二氧化钛的光催化性能和空穴电子复合之间的联系.也有研究者从掺杂体系的晶体结构和表面物化性质,如晶相(锐钛矿,金红石,无定形),比表面积,晶粒尺寸和表面羟基的角度讨论与光催化活性的关…     

掺铜二氧化钛光催化剂的XPS研究

利用浸渍法制备了铜掺杂的二氧化钛，以乙酸为模型物研究了催化剂的光催化活性，利用XPS结果对改性后的催化剂进行了分析.结果表明，改性后的催化剂表面吸附氧的提高和Cu＋/Cu2＋的共存有利于光生载流子的分离和界面电子转移，因而改善了催化剂的光催化性能.     

Effect of Preparation Methods of Bi2O3 Nanoparticles on their Photocatalytic Activity

Bi2O3 nanoparticles were prepared by means of ammonia precipitation, polyol mediated methods and microemulsion chemical method. The structure and properties of the as-prepared nanoparticles, having been submitted to a heat-treatment test at 750℃, were characterized by means of XRD. BET, XPS and UV-Vis absorption techniques. The photocatalytic oxidation reactions of benzene, toluene and xylene were used as the model reaction to measure the photocatalytic activity of Bi2O3 nanoparticles, respectively. The results show that the crystallite size of Bi2O3 prepared with different methods and calcined at 750℃ were 50. 6, 38.5 and 31.5 nm, respectively. The photocatalytic activity of Bi2O3 nanoparticles prepared with the microemulsion chemical method was higher than that of the particles prepared with the polyol mediated method; and that of the particles prepared with the micromulsion chemical method was the highest among the three. The degradation rates of the three pollutants xylene, toluene and benzene decreased in sequence.     

掺杂对PbTiO3光催化活性的影响

掺杂对ＰｂＴｉＯ_３光催化活性的影响傅希贤，单志兴，肖坤林，曾淑兰（天津大学化学系天津３０００７２）关键词ＰｂＴｉＯ_３，掺杂，光催化活性，光降解利用半导体材料光催化降解水中污染物是近年发展起来的重要课题之一［１］，一般多采用半导体氧化物为光催化剂，文...     

镧掺杂二氧化钛光催化性能的研究

通过在TiO2晶格中掺杂La2O3,考察不同的La2O3掺杂量对光催化活性的影响,找出了La2O3的最佳掺杂量.实验结果表明由于进入TiO2晶格中的La2O3使TiO2晶格发生畸变,减少了光生电子-空穴对的复合率,提高了催化剂的光催化效率.     

金属组分对TiO2光催化氧化NO-2反应的影响

亚硝酸根离子;金属组分对TiO2光催化氧化NO-2反应的影响     

碘掺杂对纳米TiO2催化剂光催化活性的影响

用溶胶-凝胶法制得了碘掺杂纳米TiO2催化剂, 考察了诸因素对相结构的影响, 这对深入揭示I-TiO2光催化降解有机物的本质具有重要意义.     

钕掺杂对纳米TiO2光催化分解水制氢活性的影响

 采用溶胶-凝胶法制备了一系列纳米TiO2和掺杂Nd3+ 的纳米TiO2光催化剂,并通过XRD, UV-Vis, TEM和N2吸附等技术对其进行了表征和分析,考察了样品光催化分解水制氢的活性. 结果表明, Nd3+的掺杂使TiO2的相变温度从600 ℃提高到800 ℃, 同时有效抑制了TiO2的粒径增长,提高了粒子的分散性和样品的比表面积, Nd3+掺杂量越大,催化剂的比表面积越大. 掺杂Nd3+ 后, TiO2的光催化制氢活性提高,本实验中Nd3+的最佳掺杂量为0.1%, 此时催化剂的活性比未掺杂TiO2提高了3.5倍. 随着焙烧温度升高, TiO2和Nd3+/TiO2样品的光催化活性均下降,但同时一定量的金红石相与锐钛矿相共存所产生的协同效应也使样品的光催化活性有所提高.     

Preparation and Photocatalytic Activity of TiO2 Films on Silica Glass Substrates by Assembly Technique

Nanostructured TiO₂ coating films on silica glass substrates were prepared by the assembly technique. TiO₂ colloids were synthesized employing the sol‐gel method using TiCl₄ as a precursor. The effect on the surface structures which was caused by the polyethylene glycol (PEG) added to the precursor solution and the photocatalytic activity were studied. The experimental results showed that the cobble‐like TiO₂ coating films were synthesized at 500 °C. On the surface of the samples, TiO₂ films exhibited uniform shape and a narrow size distribution. The result of proper PEG added to the precursor solution led to the decreasing of the size of TiO₂ particles and the increasing of the surface area of the samples. The photocatalytic activity of TiO₂ films with PEG was higher than that of samples without PEG.