Polymerization of vinyl monomers in the water–1,4-dioxane system containing peroxide and water-soluble polymer

Water-solube polymer (PST) containing triethylenetetramine side chain was prepared by the amination of chloromethylated polystyrene with triethylenetetramine in 1,4-dioxane. The polymerization of vinyl monomers was carried out in the water–organic solvent system containing PST and a very small amount of peroxide. The polymerization of methyl methacrylate proceeded smoothly in the presence of both peroxide and PST. It was found that the polymerization was initiated with the radicals generated by the interaction between hydroperoxide and amino groups of PST. 1,4-Dioxane hydroperoxide showed a high activity for the polymerization of methyl methacrylate. The maximum rate of the polymerization was observed at 60°C and in an approximately neutral solution. The addition of suitable amount of Cu(II) accelerated the polymerization of methyl methacrylate. The selective polymerization of vinyl monomers was observed in this system.     

2,2′-二邻甲氧基苯基-4,4′,5,5′-四苯基-1,2′-二咪唑复合光引发体系的光聚合动力学研究

本文研究了对2,2′-二邻甲氧基苯基-4,4′,5,5′-四苯基-1,2′-二咪唑(BMOIM)复合光引发体系引发聚合动力学过程.采用紫外光谱仪对引发剂、供氢体、增感剂在紫外区的吸收谱图进行了表征.利用实时红外光谱仪对复合光引发体系引发聚合动力学过程进行实时监测,考察了不同光强、引发剂浓度以及不同官能度单体对反应速率及最终双键转化率的影响.结果表明,在引发剂浓度为0.6%(质量分数)时,20s内双键转换率达到96%,随着引发剂浓度的提高,聚合速率增大.聚合速率以及最终双键转化率随着光强增大而增大;双官能团单体的最终双键转化率比三官能团单体的最终双键转化率要高.     

可聚合型光引发剂4-丙烯酰氧基二苯甲酮的光聚合性能研究

以实时红外光谱(RT-IR)法研究了合成的4-丙烯酰氧基二苯甲酮(4-ABP)的光聚合动力学性质,考察了不同单体、不同引发剂和助引发剂浓度、不同光强对聚合性能的影响.以萃取法对比研究了4-ABP和二苯甲酮(BP)在固化膜中的的残留量.结果表明,4-ABP是一种非常有效的光引发剂.随着引发剂浓度和光强的增大,单体转化率、最大反应速率都增大,诱导期缩短.萃取实验表明4-ABP在固化膜中的残留量远低于BP.     

Occurrence of 1,4-dioxane in cosmetic raw materials and finished cosmetic products.

Surveys of cosmetic raw materials and finished products for the presence of the carcinogen 1,4-dioxane have been conducted by the U.S. Food and Drug Administration since 1979. Analytical methods are described for the determination of 1,4-dioxane in ethoxylated cosmetic raw materials and cosmetic finished products. 1,4-Dioxane was isolated by azeotropic atmospheric distillation and determined by gas chromatography using n-butanol as an internal standard. A solid-phase extraction procedure based on a previously published method for the determination of 1,4-dioxane in cosmetic finished products was also used. 1,4-Dioxane was found in ethoxylated raw materials at levels up to 1410 ppm, and at levels up to 279 ppm in cosmetic finished products. Levels of 1,4-dioxane in excess of 85 ppm in children's shampoos indicate that continued monitoring of raw materials and finished products is warranted.     

Substituted Benzophenones as Photoinitiators

Substituted benzophenone photoinitiators were synthesized and characterized by spectroscopy methods. Their absorption spectra and kinetics of the polymerization were compared to benzophenone itself. The kinetics of the photopolymerization of 2-ethyl-2-(hydroxymethyl)-1,3-propanediol triacrylate (TMPTA) was studied by measuring the polymerization heat evolution of sample, irradiated with a laser. The influence of photoinitiator concentration and light intensity on the polymerization was also studied.     

Effect of cyclic acetals structure on efficiency of photoinitiation

Cyclic acetals were proposed as free radical polymerization photoinitiators or co‐initiators. The photopolymerization kinetics was recorded by real‐time infrared spectroscopy (RTIR). 2‐proply‐1,3‐benzodioxole (PBDO) and 2‐hexyl‐1,3‐benzodioxole (HBDO) were efficient photoinitiators for the polymerization of 1,6‐hexanedioldiacrylate (HDDA). Polymerization occurred at the highest rate with 1,3‐benzodioxolane (BDO) as a co‐initiator. When 1.82 wt % benzophenone (BP) was used as a photoinitiator, the addition of PBDO increased the rate of polymerization (R_p) and the final double bond conversion (DC_f) of HDDA, and an optimum cure rate (0.982 min^?1) was obtained at 1.64 wt % of PBDO. Combination of p‐chlorobenzophenone (CBP) and PBDO had the highest initiating reactivity. Cyclic acetals were inefficient co‐initiators for isopropylthioxanthone (ITX). Copyright © 2009 John Wiley & Sons, Ltd.     

含氟光引发剂的合成及其性能研究

以2-羟基-4'-(2-羟乙氧基)-2-甲基苯丙酮(Irgacure 2959)和全氟辛酰氯(PFOC)为原料合成了光引发剂全氟辛酸-2-[4-(2-羟基-2-甲基丙酰)苯氧基]乙酯(2959-F),利用红外光谱(FT-IR)和核磁共振(¹⁹F NMR)对2959-F进行了结构表征;通过紫外吸收光谱测定了2959-F的紫外吸收谱;通过实时红外光谱(RT-IR)对合成的含氟光引发剂进行了光聚合反应动力学研究,考察了光强和引发剂浓度对单体的双键转化率和聚合速率影响,并研究了光引发剂2959-F的抗氧阻聚性能.结果表明:随着光强的增大,单体的双键转化率和聚合速率增加;在一定范围内,引发剂的浓度越高,双键转化率越高,聚合速率越快.2959-F具有较高的双键转化率和较快的聚合速率,并且具有较好的抗氧阻聚性.     

2-亚甲基-1,3-二氧己烷衍生物的合成及自由基开环聚合

本文报道了四种2-亚甲基-1,3-二氧己烷类单体:4-甲基-2-亚甲基-1,3-二氧己烷(Ⅱ)、4,6-二甲基-2-亚甲基-1,3-二氧己烷(Ⅳ)、5,5-二甲基-2-亚甲基-1,3-二氧己烷(Ⅵ)和5,5-二乙基-2-亚甲基-1,3-二氧己烷(V Ⅲ)的合成以及自由基开环聚合。结果表明,上述单体在聚合过程中出现异构化开环现象。Ⅲ和Ⅳ的甲基位置在环上氧原子的α-碳原子上时,显示对异构化反应的影响比Ⅵ及Ⅷ的甲基和乙基在β-碳原子上时更显著。上述现象与异构化开环形成仲碳自由基中间体的倾向更大有关。 Ⅳ在苯溶液中及过氧化二叔丁基存在下,120℃反应,得到全部是聚-δ-戊内酯骨架结构的聚合物。提出了一种合成聚-δ-戊内酯类链结构的聚酯的新的途径和方法。     

Synthesis and photopolymerization kinetics of benzophenone piperazine one‐component initiator

A one‐component type II photoinitiator (PDBP), based on 4‐hydroxybenzophenone (HBP), acryloyl chloride, and piperazine, was synthesized and its structure was confirmed by ¹H‐NMR. The photopolymerization kinetics of the photoinitiator was studied by real‐time Infrared spectroscopy (FT‐IR). It indicated that PDBP was a more effective photoinitiator than that of BP/triethylamine (TEA). The rate of polymerization, final conversion increased and the induction period shortened with increase in PDBP concentration, light intensity, and amine concentration. The kinetics of photopolymerization for TPGDA incorporating PDBP in the presence of different tertiary amines as the initiating system indicated that the PDBP/TEA combination exhibited the highest polymerization rates among the PDBP/amine combinations. Copyright © 2007 John Wiley & Sons, Ltd.     

Gas chromatographic determination of 1,4-dioxane at low parts-per-million levels in glycols

1,4-Dioxane is a flammable liquid and tends to form explosive peroxides. Its formation in glycols (low parts-per-million levels), which are used as dehumidifying agents in refineries, may take place by condensation. 1,4-Dioxane thus formed gets distilled over with benzene in the refinery process. Therefore, it is necessary to identify and determine the levels of 1,4-dioxane in glycols as well as benzene. Gas chromatography (GC) is probably the best technique for this purpose. GC analysis may be carried out using a flame ionization detector. Results show that 1,4-dioxane can be comfortably determined down to 2 ppm in glycols and benzene.     

One‐component photoinitiator based on benzophenone and sesamol

A new benzodioxole derivative, 4‐(1,3‐benzodioxol‐5‐yloxy) benzophenone (BPBDO), based on benzophenone and sesamol was precisely synthesized, and it can be used as a 1‐component type II photoinitiator. Elementary analysis, atmospheric pressure chemical ionization mass spectrometry, ¹H nuclear magnetic resonance, and ¹³C nuclear magnetic resonance studies revealed that the molecular structure of BPBDO consisted of both benzophenone (BP) and benzodioxole (BDO) structures. The laser flash photolysis experiments and electron spin resonance test indicated that the process of radicals generated from BPBDO after irradiation was similar to 3 processes of ethyl 4‐dimethylaminobenzoate and BP. The kinetics of photopolymerization of the photoinitiator was also studied by real‐time infrared spectroscopy. The oxygen content, light intensity, and viscosity of the monomer affected the decomposition (R_d) and polymerization rate, and the final double bond conversion was also studied. All the results suggest that BPBDO is a 1‐component photoinitiator that is an efficient photoinitiator for free radical polymerization. In contrast to typical dual‐component photoinitiators, eg, BP/ethyl 4‐dimethylaminobenzoate or BP/BDO, BPBDO does not require an additional amine coinitiator for the initiation and is applicable in nonamine resin systems.     

Living cationic polymerization of isobutyl vinyl ether by EtAlCl2 in the presence of ether additives: Cyclic ethers,cyclic formals,and acyclic ethers with oxyethylene units

The living cationic polymerization of isobutyl vinyl ether (IBVE) was investigated in the presence of various cyclic and acyclic ethers with 1-(isobutoxy)ethyl acetate [CH₃CH(OiBu)OCOCH₃, 1 ]/EtAlCl₂ initiating system in hexane at 0°C. In particular, the effect of the basicity and steric hindrance of the ethers on the living nature and the polymerization rate was studied. The polymerization in the presence of a wide variety of cyclic ethers [tetrahydrofuran (THF), tetrahydropyran (THP), oxepane, 1,4-dioxane] and cyclic formals (1,3-dioxolane, 1,3-dioxane) gave living polymers with a very narrow molecular weight distribution (MWD) (M?_ω/M?_n ≤ 1.1). On the other hand, propylene oxide and oxetane additives resulted in no polymerization, whereas 1,3,5-trioxane gave the nonliving polymer with a broader MWD. The polymerization rates were dependent on the number of oxygen and ring sizes, which were related to the basicity and the steric hindrance. The order of the apparent polymerization rates in the presence of cyclic ether and formal additives was as follows: nonadditive ～ 1,3,5-trioxane ? 1,3-dioxane > 1,3-dioxolane ? 1,4-dioxane ? THP > oxepane ? THF ? oxetane, propylene oxide ? 0. The polymerization in the presence of the cyclic formals was much faster than that of the cyclic ethers: for example, the apparent propagation rate constant k in the presence of 1,3-dioxolane was 10³ times larger than that in the presence of THF. Another series of experiments showed that acyclic ethers with oxyethylene units were effective as additives for the living polymerization with 1 /EtAlCl₂ initiating system in hexane at 0°C. The polymers obtained in the presence of ethylene glycol diethyl ether and diethylene glycol diethyle ether had very narrow molecular weight distribution (M?_ω/M?_n ≤ 1.1), and the M?_n was directly proportional to the monomer conversion. The polymerization behavior was quite different in the polymerization rates and the MWD of the obtained polymers from that in the presence of diethyl ether. These results suggested the polydentate-type interaction or the alternate interaction of two or three ether oxygens in oxyethylene units with the propagating carbocation, to permit the living polymerization of IBVE. © 1994 John Wiley & Sons, Inc.     

三官能度甲基丙烯酰氧基单体的合成与性能研究

用甲基丙烯酰氯分别与二乙醇胺和三乙醇胺反应合成了两种三官能度甲基丙烯酰氧基单体.以实时红外光谱(RT-IR)法研究了两种单体的光聚合动力学性质,考察了不同单体、不同引发剂和引发剂浓度、不同光强对聚合性能的影响,并采用动态力学分析仪(DMA)测试了光固化后材料的力学性能.结果表明,随着引发剂浓度的增大,单体转化率、最大反应速率都增大,随着光强的增大,单体转化率、最大反应速率都降低.与二苯甲酮(BP)相比,2-羟基-2-甲基-1-苯基丙酮(1173)对两种单体具有较好的引发效果.两种单体加入三缩四乙二醇双甲基丙烯酸酯(SR209)中后,对体系光固化后的产物力学性能有不同影响.     

Studies on the copolymerization of unsaturated 1,3-dioxane derivatives—IV. Radical copolymerization of 2-furyl-5,5-dimethyl-1,3-dioxane with maleic anhydride

The copolymerization of 2-furyl-5,5-dimethyl-1,3-dioxane with maleic anhydride in the presence of a radical catalyst yields equimolar, alternating copolymers in which the furyl units have 2,5-linkage. It has been shown that 2-furyl-5,5-dimethyl-1,3-dioxane forms a charge transfer complex with maleic anhydride. The equilibrium constant for the complex was determined by NMR spectroscopy.     

Kinetic study of light-induced polymerization by real-time UV and IR spectroscopy

Real time ultraviolet (RTUV) spectroscopy was used to study the photolysis kinetics of a radical-type morpholino initiator, during the polymerization of a multiacrylate monomer exposed to UV radiation in bulk, in solution, in a polyurethane-acrylate resin, and in a poly(methyl methacrylate) matrix. The photolysis rate constant k was determined from the exponential loss profile recorded; it was found to vary between 0.1 and 3s^?1, depending on the light intensity and on the monomer concentration. The quenching of the photoinitiator excited states by the acrylate monomer was shown to be an important deactivation pathway which substantially reduces the rate of initiation. The observed influence of the film thickness and photoinitiator concentration on the k value were accounted for by the internal filter effect. Conversion versus time curves were recorded by real time infrared (RTIR) spectroscopy for the various systems examined, thus allowing a direct comparison of both the actual polymerization rate and the residual unsaturation content of the cured polymer. Various factors were shown to be responsible for the early stop of the polymerization, such as depletion of the photoinitiator, O₂ inhibition, or vitrification of the polymer. The photoinitiated cationic ring-opening polymerization of a cycloaliphatic diepoxy monomer was also studied in real time by RTUV and RTIR spectroscopy. Despite a very fast photolysis of the triarylsulphonium initiator, the polymerization of the epoxy monomer developed less rapidly than for the acrylic monomer, with shorter kinetic chain lengths. A linear relationship was found to exist between the decay rate constant and the light intensity, for both the radical and the cationic photoinitiators, as expected for a direct photolysis process.     

Oxoaminium salts as initiators for cationic polymerization of vinyl monomers

Oxoaminium salt ( 1 ), derived from 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO, 2 ) by one-electron oxidation, could be an initiator for cationic polymerization of vinyl monomers such as isobutyl vinyl ether (IBVE), 2,3-dihydrofuran, p-methoxystyrene, N-vinyl pyrrolidone, etc., to give the corresponding polymers, when 1 had a low nucleophilic counter anion. Formation of the adducts of 1 and IBVE as well as ¹H-NMR and IR data suggested the formation of polymers containing N? O? C structure as the polymer head group. In the polymerization of IBVE, the effects of solvent and concentration of 1 were little observed, however the polymerization rate was dependent on temperature. Furthermore, the thermal reaction of the polymers obtained, which were regarded as prepolymers for block copolymerization and polymeric initiators for radical polymerization, was studied. For example, poly(2-benzylidene-1,3-dioxane) obtained by the polymerization of 2-benzylidene-1,3-dioxane with oxoaminium hexafluoroantimonate ( 1, X = SbF₆) was employed as an initiator for radical polymerization of MMA to give its block copolymer with PMMA. © 1993 John Wiley & Sons, Inc.     

2,2′,5-三(2-氟苯基)-4-(3,4-二甲氧基苯基)-4′,5′-二苯基-1,1′-二咪唑复合引发体系光聚合动力学性能研究

利用实时红外对由光引发剂2,2′,5-三(2-氟苯基)-4-(3,4-二甲氧基苯基)-4′,5′-二苯基-1,1′-二咪唑(WJ-HABI)、增感剂4,4—二(N,N′—二甲基氨基)苯甲酮(EMK)及供氢体N-苯基甘氨酸(NPG)组成的复合引发体系进行光聚合动力学研究.探讨了复合引发体系的浓度、不同配比、紫外光的强度及...     

Transition Metals and Organic Ligands Influence Biodegradation of 1,4-Dioxane

1,4-Dioxane, a contaminant increasingly detected in water supplies, is a public health concern because it is classified as a possible human carcinogen. 1,4-Dioxane can be biodegraded by aerobic bacteria via monooxygenase-catalyzed reactions. While these metalloenzymes require trace metals as cofactors in their catalytic sites, these metals may be toxic at elevated concentrations. In this study, the effects of transition metals on 1,4-dioxane biodegradation by Pseudonocardia dioxanivorans CB1190, a monooxygenase-expressing bacterium, were investigated. Dose-dependent inhibition of 1,4-dioxane biodegradation by Cd(II), Cu(II), and Ni(II) was observed, whereas Zn(II) had no measurable effect on biodegradation rates. 1,4-Dioxane biodegradation in cultures exposed to 2 mg/L Cu(II) was restored in the presence of 0.005, 0.05, and 0.5 mM alginin, 0.05, and 0.5 mM cysteine, and 0.005 mM tannin. These results indicated that specific ligands bind with transition metals and alleviate bacterial toxicity. In parallel experiments, tannin and cysteine inhibited 1,4-dioxane biodegradation, but alginin, BSA, and SRNOM did not affect the biodegradation rates. Thus, monooxygenase-catalyzed biodegradation rates are subject to interactions among transition metals and natural organic ligands in the environment. Mechanistic insights and quantitative data obtained in this study will be useful for designing bioremediation strategies at sites simultaneously contaminated with metals and organic pollutants.     

Polymerization and reaction of tetraoxane with various olefins catalyzed by BF3O·(C2H5)2

The copolymerization of tetraoxane with various olefins by BF₃·O(C₂H₅)₂ in ethylene dichloride at 30°C has been studied. The gas chromatographic technique was employed for the determination of concentration of each compound. The rate of tetraoxane consumption was decreased by the addition of olefins in the order of; no addition > trans-stilbene > styrene > 1,1-diphenylethylene > 2-chloroethyl vinyl ether > cyclohexene ≥ indene ≥ α-methylstyrene. The formation of the methanol-insoluble copolymer of tetraoxane and olefin was not confirmed. However, 4-methyl-4-phenyl-1,3-dioxane and 4,4-diphenyl-1,3-dioxane were formed in the reaction of tetraoxane with α-methylstyrene and 1,1-diphenylethylene, respectively. 4,4-Diphenyl-1,3-dioxane was identified on the basis of the molecular weight measurement, elemental analysis and NMR and infrared spectroscopy. On the other hand, 1,3-dioxane derivatives were not formed in the reaction of tetraoxane with α,β-disubstituted olefins. Monomer composition dependence of the copolymerization of tetraoxane with 1,1-diphenylethylene or α-methylstyrene has been studied. The amount of 4,4-diphenyl-1,3-dioxane formed reached a maximum at a monomer composition of 1:1 in the reaction of tetraoxane with 1,1-diphenylethylene. The formation of cyclic dimer of α-methylstyrene was suppressed by tetraoxane.     

Kinetic investigations on the UV-induced photopolymerization of a diacrylate by time-resolved FTIR spectroscopy: the influence of photoinitiator concentration, light intensity and temperature

Time-resolved FTIR-ATR spectroscopy was used to study the kinetics of the photopolymerization of a diacrylate using a morpholino ketone as photoinitiator. The curing reaction was induced by monochromatic UV radiation with a wavelength of 313 nm. The influence of photoinitiator concentration [PI], light intensity I₀, and temperature on the polymerization rate R_p and the double bond conversion was investigated. The dependence of R_p on [PI] and I₀, respectively, was found to fit with theoretical predictions very well. In contrast, an increase of the temperature was found to have no effect on R_p.