Column Preconcentration of Aluminum and Copper(II) in Alloys, Biological Samples, and Environmental Samples with Alizarin Red S and Cetyltrimethylammonium-Perchlorate Adsorbent Supported on Naphthalene Using Spectrometry

A column method has been established for the preconcentration of aluminum and copper(II) with Alizarin Red S and a cetyltrimethylammonium-perchlorate ion pair supported on naphthalene, using a simple glass-tipped tube. Aluminum and copper(II) react with Alizarin Red S to form water-soluble colored chelate anions. These chelate anions form water-insoluble ternary complexes with the adsorbent on the inactive surface of naphthalene packed into a column. They are quantitatively retained in the pH ranges of 4.7-5.2 for aluminum and 5.0-10.0 for copper. The solid mass is dissolved out from the column with 5 ml of dimethylformamide (DMF) for aluminum and 5 ml of ethanol for copper and the absorbance was measured with a spectrometer at 525 nm for aluminum and at 529 nm for copper. The calibration curves were linear over the concentration ranges of 0.25-5.0 μg of aluminum in 5 ml of DMF solution and 0.50-12.0 μg of copper in 5 ml of ethanol solution. The molar absorptivities and Sandell′s sensitivities were respectively calculated to be 2.8 × 10⁴ liter · mol⁻¹ · cm⁻¹ and 9.62 × 10⁻⁴ μg · cm⁻² for aluminum and 2.5 × 10⁴ liter · mol⁻¹ · cm⁻¹ and 2.5 × 10⁻³ μg · cm⁻² for copper. Seven replicate determinations of sample solutions containing 2.5 μg of aluminum and 6.0 μg of copper gave mean absorbances of 0.520 and 0.480 with relative standard deviations of 1.67 and 0.33%, respectively. Interference due to various foreign ions has been studied and the method has been applied to the determination of aluminum in standard alloys, tea leaves, vehicle particulates, copper in coal fly ash, and commercial salt samples.     

Simultaneous determination of pethidine and methadone by capillary electrophoresis with electrochemiluminescence detection of tris(2,2′-bipyridyl)ruthenium(II)

In this paper, we described a simple and rapid method, capillary electrophoresis with electrochemiluminescence (CE–ECL) detection using tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺), to simultaneously detect pethidine and methadone. Analytes were injected to separation capillary of 67.5 cm length (25 μm i.d., 360 μm o.d.) by electrokinetic injection for 10 s at 10 kV. Under the optimized conditions: ECL detection at 1.20 V, 30 mM sodium phosphate (pH 6.0) as running buffer, separation voltage at 14.0 kV, 5 mM Ru(bpy)₃²⁺ with 50 mM sodium phosphate (pH 6.5) in the detection cell, the linear range from 2.0 × 10^− 6 to 2.0 × 10^− 5 M for pethidine and 5.0 × 10^− 6 to 2.0 × 10^− 4 M for methadone and detection limits of 0.5 μM for both of them were achieved (S/N = 3). Relative standard derivations of the ECL intensity were 2.09% and 6.59% for pethidine and methadone, respectively.     

Preparation and hydrogen permeation of SrCe0.95Y0.05O3−δ asymmetrical membranes

Asymmetrical thin membranes of SrCe_0.95Y_0.05O_3−δ (SCY) were prepared by a conventional and cost-effective dry pressing method. The substrate consisted of SCY, NiO and soluble starch (SS), and the top layer was the SCY. NiO was used as a pore former and soluble starch was used to control the shrinkage of the substrate to match that of the top layer. Crack-free asymmetrical thin membranes with thicknesses of about 50 μm and grain sizes of 5–10 μm were successfully pressed on to the substrates. Hydrogen permeation fluxes (J_H2) of these thin membranes were measured under different operating conditions. At 950 °C, J_H2 of the 50 μm SCY asymmetrical membrane towards a mixture of 80% H₂/He was as high as 7.6 × 10⁻⁸ mol/cm² s, which was about 7 times higher than that of the symmetrical membranes with a thickness of about 620 μm. The hydrogen permeation properties of SCY asymmetrical membranes were investigated and activation energies for hydrogen permeation fluxes were calculated. The slope of the relationship between the hydrogen permeation fluxes and the thickness of the membranes was −0.72, indicating that permeation in SCY asymmetric membranes was controlled by both bulk diffusion and surface reaction in the range investigated.     

Adsorption of bovine serum albumin on fused silica: Elucidation of protein–protein interactions by single-molecule fluorescence microscopy

The adsorption of bovine serum albumin (BSA) on fused silica at pH 4.7 was studied at the single molecules level by total-internal-reflection fluorescence microscopy. This pH value was the isoelectric point of BSA. At low [BSA] of 20 pM, protein molecules adsorbed as monomers. At intermediate [BSA] of 500 pM, protein molecules adsorbed as clusters of about five monomers on average. Both monomers and clusters had adsorption rate coefficients of the order 10⁻⁷ m s⁻¹ and desorption rate coefficients of about 2 × 10⁻² s⁻¹. The respective steady-state coverage was about 10× higher than that at neutral pH, presumably because of the more favorable BSA–silica electrostatics. At pH 4.7 and with [BSA] higher than 100 nM, adsorption begot further adsorption to produce nonlinear isotherms. The coverage at 1 μM BSA was 2.5× that of the linearly extrapolated coverage. This suggests that at pH 4.7, solute–adsorbate affinity was the dominant factor that explains the enhanced adsorption observed in ensemble measurements.     

Enhanced sensitivity for Cu(II) by a salicylidine-functionalized polysiloxane carbon paste electrode

A new approach for decreasing the detection limit for a copper(II) ion-selective electrode (ISE) is presented. The ISE is designed using salicylidine-functionalized polysiloxane in carbon paste. This work describes the attempts to develop the electrode and measurements of its characteristics. The new type of renewable three-dimensional chemically modified electrode could be used in a pH range of 2.3–5.4, and its detection limit is 2.7 × 10⁻⁸ mol L⁻¹ (1.2 μg L⁻¹). This sensor exhibits a good Nernstian slope of 29.4 ± 0.5 mV/decade in a wide linear concentration range of 2.3 × 10⁻⁷ to 1.0 × 10⁻³ mol L⁻¹ of Cu(II). It has a short response time (8 s) and noticeably high selectivity over other Cu(II) selective electrodes. Finally, it was satisfactorily used as an indicator electrode in complexometric titration with EDTA and determination of copper(II) in miscellaneous samples such as urine and various water samples.     

Fabrication of a template-synthesized gold nanorod-modified electrode for the detection of dopamine in the presence of ascorbic acid

Gold nanorods (GNRs) with suitable aspect ratio were synthesized with a template technique and then dispersed in a saturated sodium citrate solution by ultrasonication to form a GNR suspension. A GNR-modified electrode was fabricated using the GNR suspension. The oxidation of dopamine at the GNR/GC electrode exhibited surprisingly high electrocatalytic activity and adsorption-controlled characteristics. Square-wave voltammetry was used to detect dopamine. At the GNR/GC electrode, the linear concentration range of DA is from 1 × 10⁻⁸ M to 1 × 10⁻⁷ M and the detection limit (s/n = 3) is as low as 5.5 × 10⁻⁹ M. The current sensitivity is 3.280 μA/μM, and 1000-fold ascorbic acid (AA) cannot interfere with the determination of DA. All these performances are greatly superior to those of the bare GC electrode.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

Indirect kinetic microdetermination of oxalate, citrate, and fluoride ions

An indirect catalytic method for the separate microdetermination of oxalate, citrate, and fluoride ions is described. The method is based on the inhibition action of oxalate, citrate, and fluoride ions on the catalytic oxidation reaction of 2,4-diaminophenol-hydrogen peroxide by iron(III).Procedures for the determination of 1.76 × 10⁻² to 17.6 × 10⁻² μg/ml for oxalate ion, 3.78 × 10⁻² to 30.24 × 10⁻² μg/ml for citrate ion, and 0.38 to 4.18 μg/ml for fluoride ion are given.Quantities of 1.76 × 10⁻² to 17.6 × 10⁻² μg/ml for oxalate ion, 3.78 × 10⁻² to 30.24 × 10⁻² μg/ml for citrate ion, and 0.38 to 4.18 μg/ml for fluoride ion could be determinated with a relative error of about 1–3.5% for oxalate and citrate ions and 1–2% for fluoride ion.     

A study of the spectrophotometric determination of traces of cadmium(II) and copper(II) with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol in the presence of polyglycol octylphenyl ether

A spectrophotometric study of the Cd(II) and Cu(II) complex of a new reagent, 2-(5-bromo-2-pyridylazo)-5-diethylamino phenol (5-Br-PADAP) in the presence of polyglycol octylphenyl ether (OP) is presented. A reddish binary complex is formed at pH 9 and shows maximal absorbance at 560 nm with molar absorptivity of 1.16 × 10⁵ · mol⁻¹ · cm⁻¹ liter (Cd), 1.5 × 10⁵ mol⁻¹ · cm⁻¹ · liter (Cu). Beer's law is followed over the range 0.0 to 20 μg cadmium(II) and 0.0–18 μg copper(II). The continuous variation method and molar ratio method showed that the metal ligand ratio is 1:2; ordinarily, most ions do not interfere with the determination and the method can be applied for direct spectrophotometric determination of cadmium(II) and copper(II) in actual samples and the results obtained are satisfactory.     

Luminescent CuS nanotubes as silver ion probes

CuS nanotubes (NTs) made up of nanoparticles were successfully prepared in large quantities in an O/W microemulsion system under low temperature. Based on the characteristics of synchronous fluorescence spectroscopy (SFS), a new method with high sensitivity and selectivity was developed for rapid determination of silver ion with functional copper sulphide (CuS) nanotubes as a fluorescence probe. Under optimal conditions, functional copper sulphide displayed a calibration response for silver ion over a wide concentration range from 1.0 × 10⁻¹⁰ to 1.0 × 10⁻⁸ mol L⁻¹. The limit of detection was 0.5 × 10⁻¹⁰ mol L⁻¹ and the relative standard deviation of eight replicate measurements for the highest concentration (1 × 10⁻⁸ mol L⁻¹) was 3%. Compared with several fluorescence methods, the proposed method had a wider linear range and improved the sensitivity. Furthermore, the concentration dependence of the synchronous fluorescence intensity is effectively described by a Langmuir-type binding isotherm.     

Micromachined Enzyme Reactor for FIA System

An enzyme reactor consisting of a 2.6-m-long silicon capillary with glucose oxidase immobilized on the inner surface was fabricated using micromachining techniques. A V-shaped groove of 100 μm width, formed by anisotropic etching, was anodically bonded to a glass plate to create the capillary. Glucose oxidase was covalently immobilized with 3-aminopropyltriethoxysilane and glutaraldehyde. The reactor was evaluated by connecting it to a Flow injection analysis system for glucose detection. Glucose concentrations were in the range of 10⁻³ to 5 × 10⁻²M with a volume of 0.2 μl of glucose solution.     

Amperometric glucose biosensor based on a gold nanorods/cellulose acetate composite film as immobilization matrix

We report on the utilization of gold nanorods to create a highly responsive glucose biosensor. The feasibility of an amperometric glucose biosensor based on immobilization of glucose oxidase (GOx) in gold nanorod is investigated. GOx is simply mixed with gold nanorods and cross-linked with a cellulose acetate (CA) medium by glutaraldehyde. The adsorption of GOx on the gold nanorods is confirmed by X-ray photoelectron spectroscopy (XPS) measurements. Circular dichroism (CD) and UV-spectrum results show that the activity of GOx was preserved after conjugating with gold nanorods. The current response of modified electrode is 10 times higher than that of without gold nanorods. Under optimal conditions, the biosensor shows high sensitivity (8.4 μA cm⁻² mM⁻¹), low detection limit (2 × 10⁻⁵ M), good storage stability and high affinity to glucose (). A linear calibration plot is obtained in the wide concentration range from 3 × 10⁻⁵ to 2.2 × 10⁻³ M.     

Effect of high rates of mass transport on oxygen reduction at copper electrodes: Implications for aluminium corrosion

The reduction of oxygen at copper microelectrodes (25 μm diameter) in aqueous solution (pH 7) has been studied under conditions of high mass transport, similar to those experienced by μm sized copper-containing inclusions in aluminium alloys during corrosion. Contrary to previous studies at copper electrodes operating at lower mass transport rates, oxygen reduction limiting currents show an apparent number of electrons which decrease towards 2 as the mass transport rate increases (mass transfer coefficients up to ca. 0.55 cm s⁻¹), rather than a 4-electron process. These new data suggest that the treatment of oxygen reduction as a 4-electron transfer process at micron and smaller-sized copper intermetallics in aluminium alloys may require revision.     

Preparation of PTFE-based fuel cell membranes by combining latent track formation technology with graft polymerization

Swift heavy 56 MeV ¹⁵N³⁺ ions were generated with particle fluences of 0, 3×10⁶, 3×10⁷, 3×10⁸, 3×10⁹ ions/cm² to form a latent track zone in a 25-μm-thick film of polytetrafluoroethylene (iPTFE). Styrene (St) was then grafted onto the iPTFE films by UV-irradiation or pre-γ-irradiation, and after sulfonation iPTFE-based proton-conducting membranes were obtained, here called, iPTFE-g(UV)-PStSA and iPTFE-g(γ)-PStSA membranes, respectively, which had a straight cylindrical damage zone around the ion path. The degree of grafting was found to be about 7.5% with a particle fluence of 3×10⁷ ions/cm² and with either the UV-method or the γ-method. The ion-exchange capacity, proton conductivity in the thickness direction, MeOH permeability, tensile strength and elongation at break of the obtained iPTFE-g(UV)-PStSA membrane were 0.50 mmol/g, 0.06 S/cm, 0.15×10⁻⁶ cm²/s, 50 MPa and 600%, in contrast to 0.06 mmol/g, 0.06 S/cm, 0.35×10⁻⁶ cm²/s, 19 MPa and 210% for the iPTFE-g(γ)-PStSA membrane, respectively. In comparison, the Nafion 112 measured in our laboratory exhibited an ion-exchange capacity of 0.91 mmol/g, a proton conductivity of 0.06 S/cm, a MeOH permeability of 1.02×10⁻⁶ cm²/s, a tensile strength of 35 MPa and an elongation at break of 295%. It can be concluded from these data that the lower crossover of MeOH, the same proton conductibility, the lower ion-exchange capacity, and the superior mechanical properties of the UV-grafted proton-conducting membranes compared to the Nafion make them promising materials for widespread application in direct methanol fuel cells. On the other hand, the tests of mechanical strength showed that the PTFE base film is subject to degradation by the ion-beam irradiation as well as the γ-irradiation.     

Laser ablation inductively coupled plasma mass spectrometry for imaging of copper, zinc, and platinum in thin sections of a kidney from a mouse treated with cis-platin

Platinum complexes are used for the treatment of several types of cancer. High platinum concentrations in the target tissue and low concentrations in dose-limiting tissue structures such as renal tubules are desirable to assure selective toxicity. Microlocal analysis of platinum distribution in tissue sections may thus contribute to the optimization of platinum therapy. Scanning laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was used to produce images of element distribution in 14-μm thin sections of kidney tissue from a mouse treated with cis-platin 60 min prior to victimization. The sample surface was scanned (raster area 300 mm²) with a focused laser beam (wavelength 266 nm, diameter of laser crater 50 μm, inter line distance 50 μm and laser power density 3 × 10⁹ W cm⁻²) in a cooled laser ablation chamber (about −15 °C) developed for these measurements. The laser ablation system was coupled to a double-focusing sector field ICP-MS. Ion intensities of ⁶³Cu⁺, ⁶⁴Zn⁺, and ¹⁹⁶Pt⁺ were measured within the tissue by LA-ICP-MS. Matrix-matched laboratory standards served for calibration of analytical data. The mass spectrometric analysis yielded an inhomogeneous distribution for Cu, Zn, and Pt in thin kidney sections. Copper was enriched in the capsule and outer cortex, zinc in the inner cortex and the platinum concentration followed a centripetal gradient with clear medullar enrichment. Thus, scanning LA-ICP-MS may be a useful tool in the preclinical development of new and less nephrotoxic platinum complexes.     

Evaluation of a chloramine-T-selective electrode for catalytic titration of silver and mercury(II) based on iodide-catalyzed chloramine-T reactions

Semiautomatic methods are described for the catalytic titrimetric determination of microamounts of silver and mercury(II) using a chloramine-T-selective electrode as monitor. The methods are based on the inhibitory effect of Ag(I) and Hg(II) on the iodide-catalyzed chloramine-T-arsenite and chloramine-T-H₂O₂ reactions. Microamounts of silver in the range 0.2–200 μg (1 × 10⁻⁷−1 × 10⁻⁴ M) and of mercury(II) in the range 0.1–200 μg (2.5 × 10⁻⁸−5 × 10⁻⁵ M) were determined using the chloramine-T-As(III) indicator reaction. Mercury(II) in the range 4–2000 μg (1 × 10⁻⁶−5 × 10⁻⁴ M) was also determined using the chloramine-T-H₂O₂ indicator reaction. The accuracy and precision were in the range 0.1–1%.     

Cysteine functionalized poly(hydroxyethyl methacrylate) monolith for heavy metal removal

The aim of this study was to investigate the performance of monoliths composed of hydroxyethyl methacrylate (HEMA) to which N-methacryloyl-(L)-cysteine methyl ester (MAC) was polymerized for removal of heavy metal ions. Poly(HEMA-MAC) monolith was produced by bulk polymerization. Poly(HEMA-MAC) monolith was characterized by FTIR and scanning electron microscopy (SEM). The poly(HEMA-MAC) monolith with a swelling ratio of 89%, and containing 69.4 μmol MAC/g were used in the adsorption studies. Adsorption capacity of the monolith for the metal ions, i.e., Cu²⁺, Cd²⁺, Zn²⁺, Hg²⁺, and Pb²⁺ were investigated in aqueous media containing different amounts of the ions (10–750 mg/L) and at different pH values (3.0–7.0). The maximum adsorption capacities of the poly(HEMA-MAC) monolith were 68.2 mg/g for Zn²⁺, 129.2 mg/g for Cu²⁺, 245.8 mg/g for Pb²⁺, 270.2 mg/g for Hg²⁺, and 284.0 mg/g for Cd²⁺. pH significantly affected the adsorption capacity of MAC incorporated monolith. The competitive adsorption capacities were 587 μmol/g for Zn²⁺, 1646 μmol/g for Cu²⁺, 687 μmol/g for Pb²⁺, 929 μmol/g for Hg²⁺, and 1993 μmol/g for Cd²⁺. The chelating monolith exhibited the following metal ion affinity sequence on molar basis: Cd²⁺ > Cu²⁺ > Hg²⁺ > Pb²⁺ > Zn²⁺. The formation constants of MAC–metal ion complexes have been investigated applying the method of Ruzic. The calculated values of stability constants were 5.28 × 10⁴ L/mol for Cd²⁺, 4.16 × 10⁴ L/mol for Cu²⁺, 2.27 × 10⁴ L/mol for Hg²⁺, 1.98 × 10⁴ L/mol for Pb²⁺, and 1.25 × 10⁴ L/mol for Zn²⁺. Stability constants were increased with increasing binding affinity. The chelating monoliths can be easily regenerated by 0.1 M HNO₃ with higher effectiveness. These features make poly(HEMA-MAC) monolith a potential adsorbent for heavy metal removal.     

Determination of antioxidant capacities of vegetable oils by ferric-ion spectrophotometric methods

Two ferric-ion-based total antioxidant capacity methods: 1,10-phenanthroline (Phen) and ferric reducing antioxidant power (FRAP) were used for determination of antioxidant capacities (AC) of the acetonic and methanolic extracts of vegetable oils. The obtained mean Phen and FRAP values for acetonic extracts of olive oils, rapeseed, rice and four sunflower oils (39.3–336.5 and 39.5–339.6 μmol Fe/100 g) were higher than for methanolic extracts (22.8–307.3 and 23.5–300.1 μmol Fe/100 g). However, antioxidant capacities of methanolic extracts of corn oil, blended oils and two sunflower oils with garden green flowers (56.5–312.9 and 53.9–306.5 μmol Fe/100 g for Phen and FRAP methods, respectively) were higher than for acetonic extracts of these oils (54.2–249.2 and 52.9–244.7 μmol Fe/100 g for Phen and FRAP methods, respectively). There is a linear and significant correlation between these two analytical methods (r = 0.9989 and 0.9986 for acetonic and methanolic extracts). Also, total phenolic compounds (TPC) in the studied oils correlated with their antioxidant capacities determined by Phen and FRAP methods (r = 0.9012, 0.7818 and 0.8947, 0.7830 for acetonic and methanolic extracts, respectively). The comparable precision (R.S.D. = 0.8–4.6%, 0.9–4.9% and 0.7–4.0%, 0.6–4.0% for acetonic and methanolic extracts, respectively) and sensitivity ( = 1.27 × 10⁴, 1.11 × 10⁴ and 2.62 × 10⁴ dm³ mol⁻¹ cm⁻¹) for the proposed Phen and the modified FRAP methods, demonstrate the benefit of the Phen method in the routine analysis of antioxidant capacities of vegetable oils.     

Catalytic microdetermination of iron

A reaction rate method is described for the microdetermination of iron. The method is based on the catalytic action of iron on the reaction of 2,4-diaminophenol with hydrogen peroxide. The effect of reagent concentration is studied and the maximum tolerable amounts of interfering ions are determined. Procedures for the determination of 2.8 × 10⁻³ to 2.8 × 10⁻² μg/ml are given.Quantities of 2.8 × 10⁻³ to 2.8 × 10⁻² μg/ml could be determinated with a relative error of about 2%.     

XAS and microscopy studies of the uptake and bio-transformation of copper in Larrea tridentata (creosote bush)

Herein we present work directed toward understanding the mechanisms employed by Larrea tridentata (Creosote bush) to uptake and simultaneously defend against the presence of excess copper. The location and nature of copper in the plant have been studied on several length scales: greater than 10 μm (scanning electron microscopy), less than 10 μm (transmission electron microscopy) and atomic level structure and speciation (EXAFS and XANES). Two interesting results are apparent: creosote takes up or adsorbs copper from the soil in the Cu(II) oxidation state and transports it to the leaves where copper is found as Cu(I) and Cu(II). The transport agent appears to be a Cu phytochelatin. Additionally, creosote may be immobilizing and excreting copper via at least two additional mechanisms: storage of metals in vacuoles and excretion of copper into the sticky resinous substance found on the leaf surface. Creosote may also accumulate wind-blown particulates that can easily adhere to the resinous sticky surface of the plant. If, however, the particulates are <10 μm they may enter the leaf by respiration through the plant ‘stomata’ that have openings between 5 μm and 10 μm. As such, creosote may be a natural bio-indicator for airborne particulates that are <10 μm.