Study of Schottky contact between Au and NiO nanowire by conductive atomic force microscopy (C-AFM): The case of surface states

In this work, NiO nanowires have been synthesized by a hydrothermal reaction of NiCl₂ with Na₂C₂O₄ in the presence of ethylene glycol at 180 °C for 12 h, then calcinated at 400 °C for 2 h. The NiO nanowires were analyzed by means of scanning electron microscope (SEM), atomic force microscope (AFM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The resulting current–voltage (I–V) characteristics of the NiO nanowires exhibited a clear rectifying behavior. This rectify behavior was attributed to the formation of a Schottky contact between Au coated atomic force microscopy (AFM) tip and NiO nanowires (nano-M/SC) which was dominated by the surface states in NiO itself. Photo-assisted conductive AFM (PC-AFM) was used to demonstrate how the I–V characteristics are influenced by the surface states. Our I–V results also showed that the nano-M/SCs had a good photoelectric switching effect at reverse bias.     

Effect of surface roughness on nucleation and growth of vanadium pentoxide nanowires

The effect of surface roughness on subsequent growth of vanadium pentoxide (V₂O₅) nanowires is examined. With increasing surface roughness, both the number density and aspect ratio of V₂O₅ nanowires increase. Structures and morphology of obtained nanowires were characterized by field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD). The nanowires are approximately 40-90 nm in diameter and 2 μm in length. X-ray diffraction (XRD) analysis indicates that the obtained nanowires are orthorhombic structure with (0 0 1) out-of-plane orientation. The luminescence property of V₂O₅ nanowires has been investigated by photoluminescence (PL) at 150 K and 300 K. PL results show intense visible emission, which is attributed to different inter-band transitions between the V 3d and O 2p band. This simple fabrication approach might be useful for fabrication of large area V₂O₅ nanowires arrays with high density.     

Effect of pore size on ferroelectric properties of multiferroic BiFeO3 films prepared on porous silicon

The ferroelectric properties of BiFeO₃ (BFO) films spray deposited on porous silicon have been studied. The analysis of XRD and FESEM investigations show that the crystalline strain in the BFO films increases with pore size. The BFO films on porous silicon substrate showed improvement in ferroelectric fatigue behavior, remanent polarization and ferroelectric switching time. A maximum memory window of 5.54 V at 1 MHz and a large remanent polarization (P_r) of 13.1 μC/cm² have been obtained at room temperature. The improvement in the ferroelectric properties of these films has been correlated to the crystalline strain.     

Field-emission enhancement of molybdenum oxide nanowires with nanoprotrusions

The field-emission properties of molybdenum oxide nanowires grown on a silicon substrate and its emission performance in various vacuum gaps are reported in this article. A new kind of molybdenum oxides named nanowires with nanoscale protrusions on their surfaces were grown by thermal vapor deposition with a length of ~1 μm and an average diameter of ~50 nm. The morphology, structure, composition and chemical states of the prepared nanostructures were characterized by scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). According to XRD, XPS, and TEM analyses, the synthesized samples were composed of MoO₂ nanowires formed over a thin layer of crystalline Mo₄O₁₁. TEM observation revealed that these nanowires have some nanoscale protrusion on their surface. These nanoprotrusions resulted in enhancement of field-emission properties of nanowires comprising nanoprotrusions. The turn-on emission field and the enhancement factor of this type of nanostructures were measured 0.2 V/μm and 42991 at the vacuum gap of 300 μm, respectively. These excellent emission properties are attributed to the special structure of the nanowires that have potential for utilizing in vacuum nanoelectronic and microelectronic applications.     

Room-temperature magnetic properties of SiC based nanowires synthesized via microwave heating method

Two kinds of ferromagnetic SiC based nanowires with and without Ni catalyst were successfully synthesized by employing microwave heating method. The comprehensive characterizations and vibrating sample magnetometer (VSM) have been applied to investigate the micro-structures and magnetic properties of as-grown nanowires. For the nanowires synthesized without using Ni catalyst, the diameters and lengths are in the range of 20–60 nm and dozens of micrometers, respectively. Particularly, the results of transmission electron microscopy (TEM) show that the nanowires consist of SiC core and SiO_x shell. The SiC/SiO_x coaxial nanowires exhibit room-temperature ferromagnetism with saturation magnetization (Ms) of 0.2 emu/g. As to the nanowires obtained using Ni catalyst, the scanning electron microscopy (SEM) results indicate that the Ni catalyzed nanowires have a nano-particle attached on the tip and a uniform diameter of approximately 50 nm. The vapor-liquid-solid (VLS) growth mechanism can be used to explain the formation of the Ni catalyzed nanowires. The detection result of VSM indicates that the Ni catalyzed nanowires possess the paramagnetism and the ferromagnetism, simultaneously. The enhancement of the ferromagnetism, compared with the SiC/SiO_x coaxial nanowires, could be attributed to the Ni₂Si and NiSi phases.     

Magnetic properties of nano-crystalline Gd- or Pr-substituted CoFe2O4 synthesized by the citrate precursor technique

The magnetic properties of nano-crystalline CoM_xFe_2−xO₄ (where M=Gd and Pr and x=0, 0.1 and 0.2) powders prepared by a citrate precursor technique have been studied by using vibrating sample magnetometer (VSM). The crystallite sizes of the materials were varied by altering the synthetic conditions and are within the range of a minimum of 6.8 nm and a maximum of 87.5 nm. The materials were characterized by powder X-ray diffraction (XRD) and thermogravimetric (TG) measurements. TG study indicates the formation of the spinel ferrite phase at 220°C. The phase identification of the materials by XRD reveals the single-phase nature of the materials. The room temperature saturation magnetization of the ferrite materials decreases with the reduction of size. This has been attributed to the presence of superparamagnetic fractions in the materials and spin canting at the surface of nano-particles. Insertion of rare-earth atoms in the crystal lattice inhibits the grain growth of the materials in a systematic manner compared with that of the pure cobalt ferrite materials. The improved coercivity compared with those for the pure cobalt ferrites is attributed to the contribution from the single ion anisotropy of the rare-earth ions present in the crystal lattice and the surface effects resulting in alteration of magnetic structures on the surface of nano-particles.     

Copper diffusion in Ti-Si-N layers formed by inductively coupled plasma implantation

Ternary Ti-Si-N refractory barrier films of 15 nm thick was prepared by low frequency, high density, inductively coupled plasma implantation of N into Ti_xSi_y substrate. This leads to the formation of Ti-N and Si-N compounds in the ternary film. Diffusion of copper in the barrier layer after annealing treatment at various temperatures was investigated using time-of-flight secondary ion mass spectrometer (ToF-SIMS) depth profiling, X-ray diffractometer (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) and sheet resistance measurement. The current study found that barrier failure did not occur until 650 °C annealing for 30 min. The failure occurs by the diffusion of copper into the Ti-Si-N film to form Cu-Ti and Cu-N compounds. FESEM surface morphology and EDX show that copper compounds were formed on the ridge areas of the Ti-Si-N film. The sheet resistance verifies the diffusion of Cu into the Ti-Si-N film; there is a sudden drop in the resistance with Cu compound formation. This finding provides a simple and effective method of monitoring Cu diffusion in TiN-based diffusion barriers.     

The effect of carrier gas flow on structural and optical properties of TiO2 nanowires

Optical properties and photoluminescence of TiO₂ nanowires, synthesized by two-step thermal evaporation process, under different Ar gas flow as carrier have been studied. The gas flow was varied from 50 to 150 sccm in order to find the optimum gas flow to growth TiO₂ nanowires. As evidenced by X-ray diffraction patterns, our synthesized nanowires, were found to be crystalline rutile TiO₂. Our results indicated a convenient gas flow for controlling diameter size of nanowires was about 100 sccm. In this case, diameters and lengths were, respectively, within the ranges of 40–100 and 400–1800 nm. The experimental data of the reflectance of TiO₂ nanowires have been obtained through using spectrometer of wavelength 250–800 nm that has been indicated reflectance decreasing with increasing the gas flow, due to the scattering from the surface of the nanowires and also an increase in voids’ roughness. Under excitation 370 nm, the TiO₂ nanowires can emit light peaked at 435 nm. It is believed that peak 435 may be due to free excitons emission.     

CO oxidation over sonochemically synthesized Pd–Cu/Al2O3 nanocatalyst used in hydrogen purification: Effect of Pd loading and ultrasound irradiation time

The bimetallic Pd–Cu nanocatalysts with different Pd loadings and ultrasonic irradiation times were sonochemically synthesized and their activities toward CO oxidation were investigated. XRD, FESEM, TEM, BET, FTIR and TG-DTG techniques were employed in nanocatalysts characterization. XRD data confirmed formation of CuAl₂O₄ spinel with an average crystallite size of 4.9 nm. FESEM images revealed more uniform pattern and also fewer agglomerations were observed by increasing ultrasonic irradiation time. In agreement with FESEM result, TEM images depicted nanoparticles and uniform dispersion of active phase over alumina. BET surface analysis showed that increasing the Pd loading has no significant effect on surface area; whereas by increasing irradiation time the surface area increases slightly. Catalytic performance tests of synthesized samples showed that Pd(1.5%)–Cu(20%)/Al₂O₃ with 95 min ultrasonic irradiation time had the best activity over the course of reaction. In addition, increasing CO at feed composition revealed that among synthesized nanocatalysts with 0.5%, 1% and 1.5% of Pd, synthesized sample with 1.5% of Pd had the best low-temperature activity.     

Influence of CuO and sintering temperature on the microstructure and magnetic properties of Mg–Cu–Zn ferrites

The synthesis of a series of Mg–Cu–Zn ferrites with the substitution of Cu for Mg has been obtained by solid-state reaction method. Microstuctural and structural analyses were carried out using a scanning electron microscope and X-ray diffraction (XRD), respectively. The lattice parameter is found to increase with increasing copper content. A remarkable densification is observed with the addition of Cu ions in the ferrites. Microstructural analyses indicate that CuO influences the microstructure of the ferrites by the formation of liquid phase during sintering. The grain size significantly increases with increasing copper content. Exaggerated grain growth is observed for the samples of x=0.25–0.35. The initial magnetic permeability (μ′) increases sharply with increasing concentration of Cu ions. This increase in μ′ is explained with the grain growth mechanism and enhanced densification of the ferrites. The resonance frequency of all the samples shifts toward the lower frequency as the permeability increases with Cu content. Sintering temperature T_s also affects the densification, grain growth and initial magnetic permeability of the samples.     

Synthesis process of nanowired Al/CuO thermite

Al/CuO nanothermites were fabricated by thermal oxidation of copper layer at 450 °C for 5 h and by aluminum thermal evaporation: thermal evaporation allows producing thin layer less than 2 μm in size. The copper has been deposited by electroplating or thermal evaporation depending on the required thickness. The obtained diameter of Al/CuO nanowires is 150-250 nm. Al/CuO nanowires composite were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC) and differential thermal analysis (DTA). Two distinct exothermic reactions occurred at 515 and 667 °C and total energy release of this thermite is 10 kJ/cm³.     

Ultrasonic-induced synthesis of high surface area colloids CeO2–ZrO2

The nanostructures of high surface area ceria–zirconia colloids have been successfully synthesized via a sonochemical method in the presence of polyethylene glycol 600. Their structural characteristics have been investigated using powder XRD, FESEM, BET surface area, TG, and other techniques. The average size of CeO₂–ZrO₂ nanoparticles is estimated to be 3.7 nm using Debye–Scherrer’s equation. The BET analysis indicates that colloids CeO₂–ZrO₂ have a remarkably high surface area of 226 m² g⁻¹.     

Surfactant-free synthesis of novel copper oxide (CuO) nanowire–cobalt oxide (Co<Subscript>3</Subscript>O<Subscript>4</Subscript>) nanoparticle heterostructures and their morphological control

A simple and surfactant-free synthesis of novel heterostructures comprising of copper oxide (CuO) nanowires uniformly decorated with cobalt oxide (Co₃O₄) nanoparticles was demonstrated by combining thermal growth and wet-coating method. The heterostructures were synthesized by thermally decomposing cobalt salt (cobalt nitrate) into Co₃O₄ nanoparticles onto vapor–solid (VS)-grown CuO nanowires. X-ray diffraction (XRD) and high resolution transmission electron microscopy (TEM) confirmed the presence of CuO and Co₃O₄ phases as well as a narrow size distribution of Co₃O₄ nanoparticles (average diameter ~7.0 ± 1.5 nm) on CuO nanowires (average diameter of nanowire tips ~67.9 ± 18.6 nm). Unique interfacial lattice relationship was observed for (111) Co₃O₄ nanoparticles on (200) CuO nanowire surface resulting in hemispherical shape of the former. For the first time, further systematic studies were performed to understand the influence of various parameters (cobalt salt concentration and annealing temperature, atmosphere, and time) on the morphological evolution of Co₃O₄ nanoparticles on CuO nanowires. Interestingly, by varying these parameters, it was possible to grow Co₃O₄ in different shapes (spherical, triangular, rectangular, cubical, and hexagonal nanoparticles) and forms (shells and nanorods). It was observed that all these parameters play a critical role in influencing the surface migration, nucleation, and growth of Co₃O₄ nanoparticles on CuO nanowires and this assisted in understanding the involved growth mechanisms. Finally, UV–vis–NIR spectroscopy and band gap energies for these heterostructures were evaluated that showed higher photocatalytic degradation efficiency for Rhodamine B under low-power visible-light illumination.     

Zinc oxide nano-particles--sonochemical synthesis, characterization and application for photo-remediation of heavy metal

Zinc oxide nanoparticles have been synthesized sonochemically from zinc acetate solution in aqueous methanol, ethanol and iso-propanol containing about 5 volume% of alcohol. Characterization with FESEM, XRD, AFM and BET surface area shows that the synthesized particles differ in shape and size. ZnO synthesized using isopropanol was observed to be the most crystalline one. The synthesized nanoparticles were used for the photocatalytic reduction of hexavalent chromium in aqueous medium under solar radiation. It was observed that the initial reduction rates varied with the difference in morphology of ZnO crystallites.     

Fabrication of copper oxide nanofluid using submerged arc nanoparticle synthesis system (SANSS)

The optimal parameters are found for preparing nanofluid in our submerged arc nanoparticle synthesis system (SANSS) using a copper electrode. A suspended copper oxide nanofluid is thus produced at the current of 8.5–10 A, voltage of 220 V, pulse duration of 12 μs, and dielectric liquid temperature of 2°C. The CuO nanoparticle are characterized by transmission electron microscopy (TEM), field emission scanning electron microscope (FESEM), X-ray diffraction (XRD), electron diffraction pattern (SAD) and electron spectroscopy for chemical analysis (ESCA). The equality volume spherical diameter of the obtained copper oxide particle is 49.1 nm, regular shape and narrow size distribution.     

Thermal annealing effects on the dynamic photoresponse properties of Al-doped ZnO nanowires network

In this study, UV photodetectors based on a network of aluminium-doped zinc oxide (AZO) nanowires were manufactured at a low cost; for this purpose, a fast and simple fabrication process that involved dropping nanowires dispersion solution was employed instead of the conventional e-beam lithography process that is used to manufacture single nanowire–based UV photodetectors. It was demonstrated that nanowire network–based UV photodetectors provide a much faster UV photoresponse than conventional single nanowire–based UV photodetectors. The fast UV photoresponse of the fabricated UV photodetector can be attributed to the fact that the potential barriers formed in the nanowire network junctions effectively block the flow of electrons during the process of photocurrent decay. Furthermore, the UV photoresponse under illumination by a 254 nm UV source was studied as a function of the annealing temperature of the AZO nanowires network at a bias of 5 V. The fabricated UV photodetector showed the fastest response of 2 s to UV illumination in air when the sample was annealed in air for 1 h at 300 °C.     

Defect-controlled growth of ZnO nanostructures using its different zinc precursors and their application for effective photodegradation

Various zinc precursors, such as zinc acetate, zinc nitrate, zinc sulfate, and zinc chloride, have been used to control the formation of zinc oxide (ZnO) nanostructures onto aluminum substrate by chemical means. FESEM images of the ZnO nanostructures showed the formation of different morphologies, such as flakes, nanowalls, nanopetals, and nanodisks, when the nanostructures were synthesized using zinc acetate, zinc nitrate, zinc sulfate, and zinc chloride precursors, respectively. The TEM image of disk-like ZnO nanostructures formed using zinc chloride as a precursor revealed hexagonally shaped particles with an average diameter of 0.5 μm. Room-temperature photoluminescence (PL) spectra revealed a large quantity of surface oxygen defects in ZnO nanodisks grown from zinc chloride compared with those using other precursors. Furthermore, the ZnO nanostructures were evaluated for photocatalytic activity under ultraviolet (UV) light illumination. Nanostructures having a disk-like shape exhibited the highest photocatalytic performance (k = 0.027 min⁻¹) for all the ZnO nanostructures studied. Improved photocatalytic activity of ZnO nanodisks was attributed to their large specific surface area (4.83 m² g⁻¹), surface oxygen defects, and super-hydrophilic nature of their surface, which is particularly suitable for dye adsorption.     

GMR in multilayered nanowires electrodeposited in track-etched polyester and polycarbonate membranes

Commercially available track-etched polyester membranes were used as templates to electrodeposit Co–Ni–Cu/Cu multilayered nanowires, giving room-temperature current perpendicular to plane (CPP) giant magnetoresistance (GMR) values of up to ∼12%. In contrast to similar nanowires electrodeposited in track-etched polycarbonate membranes, the GMR obtained in multilayered nanowires electrodeposited in the polyester membranes increased with decreasing Cu-layer thickness t_Cu, for t_Cu in the 2–7 nm range, indicating a lack of ferromagnetic coupling through pinholes, etc. Transmission electron micrographs showed clear evidence for smooth, parallel layer interfaces in the nanowires.     

Synthesis and photoluminescence properties of silver nanowires

Silver nanowires of 50–190 nm in diameters along with silver nanoparticles in the size range of 60–200 nm in prismatic and hexagonal shapes are synthesized through chemical process. The lengths of the silver nanowires lie between 40 and 1000 μm. The characterizations of the synthesized samples are done by X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV–visible absorption spectroscopy. The syntheses have been done by using two processes. In the first process, relatively thicker and longer silver nanowires are synthesized by a soft template liquid phase method at a reaction temperature of 70 °C with methanol as solvent. In the second process, thinner silver nanowires along with silver nanoparticles are prepared through a polymer mediated polyol process at a reaction temperature of 210 °C with ethylene glycol as solvent. The variations of photoluminescence (PL) emission from the silver nanocluster dispersed in methanol as well as in ethylene glycol are recorded at room temperature under excitation wavelengths lying in between 300 and 414 nm. The blue–green PL emission is observed from the prepared samples and these emissions are assigned to radiative recombination of Fermi level electrons and sp- or d-band holes.     

Structural and magnetic properties of nano-crystalline Ni–Zn ferrites synthesized using egg-white precursor

Nano-crystalline nickel–zinc ferrites of different compositions; Ni_1−xZn_xFe₂O₄ (x=0.0–1.0) were prepared by a precursor method involving egg-white and metal nitrates. An appropriate mechanism for the egg-white-metal complexation was suggested. Differential thermal analysis-thermogravimetry, X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), vibrating sample magnetometer and AC-magnetic susceptibility measurements were carried out to investigate chemical, structural and magnetic aspects of Ni–Zn ferrites. XRD confirmed the formation of spinel cubic structure. The average crystallite size was calculated using line broadening in XRD patterns. Structural parameters like lattice constant, X-ray density, bond lengths and inter-cationic distance were determined from XRD data. TEM showed agglomerated particles with average size agreed well with that estimated using XRD. FT-IR spectra confirm the formation of spinel structure and further lends support to the proposed cation distribution. Zn-content was found to have a significant influence on the magnetic properties of the system. The changes in the magnetic properties can be attributed to the influence of the cationic stoichiometry and their occupancy in the specific sites.