Preparation of the visible light responsive TiO2 thin film photocatalysts by the RF magnetron sputtering deposition method

TiO₂ thin film photocatalysts which could induce photoreactions under visible light irradiation were successfully developed in a single process by applying an ion engineering technique, i.e., the radio frequency (RF) magnetron sputtering deposition method. The TiO₂ thin films prepared at temperatures greater than 773 K showed the efficient absorption of visible light; on the other hand, the TiO₂ thin films prepared at around 573 K were highly transparent. This clearly means that the optical properties of TiO₂ thin films, which absorb not only UV but also visible light, can be controlled by the preparation temperatures of the RF magnetron sputtering deposition method. These visible light responsive TiO₂ thin films were found to exhibit effective photocatalytic reactivity under visible light irradiation (λ > 450 nm) at 275 K for the reductive decomposition of NO into N₂ and N₂O. From various characterizations, the orderly aligned columnar TiO₂ crystals could be observed only for the visible light responsive TiO₂ thin films. This unique structural factor is expected to modify the electronic properties of a TiO₂ semiconductor, enabling the efficient absorption of visible light.     

Nitrogen-doped TiO2 from TiN and its visible light photoelectrochemical properties

Homogeneous titanium nitride (TiN) thin film was produced by simple electrophoreic deposition process on Ti substrate in an aqueous suspension of nanosized TiN powder. Nitrogen-doped titanium dioxide (TiO_2−xN_x) was synthesized by oxidative annealing the resulted TiN thin film in air. Photoelectrochemical measurements demonstrated visible light photoresponse for the electrode of annealed electrophoreic deposited TiN samples. It is found that the synthesized TiO_2−xN_x electrode showed higher photo potential under white and visible light illumination than the pure TiO₂ electrode. The photocurrent under visible light illumination was also observed, which increased with the increase of deposition time of TiN thin films.     

Preparation and characterization of TiO2 sols and their UV-cured hybrid thin films on plastic substrates

In this research, TiO₂ sols were synthesized via a sol?Cgel reaction at room temperature followed by heating under reflux. Hybrid thin films were prepared using the TiO₂ sols and dipentaerythritol hexacrylate on poly(methyl methacrylate) substrates via spin coating followed by UV-curing. The images of transmission electron microscopy (TEM) and results of dynamic light scattering (DSL) showed that some originally synthesized TiO₂ nanoparticles aggregated while many small-sized (~5?nm) TiO₂ nanoparticles still existed after reflux heating. The synthesized TiO₂ sols showed poor photocatalytic ability, which might avoid degradation of organic moieties in the hybrids. The refractive indices of the hybrid thin films were increased from 1.66 to 1.82 while the water contact angles on the thin films were increased from 70.2° to 87.7° with the increment of TiO₂ content. Increasing the heating time of the TiO₂ sol resulted in an increase in the refractive index and contact angle.     

Optical, mechanical, and dielectric properties of Bi1/2Na1/2TiO3 thin film synthesized by sol–gel method

The Bi_1/2Na_1/2TiO₃ (BNT) thin film has been researched as an excellent candidate of lead-free ferroelectric materials. We synthesized BNT thin film on Si wafers or quartz glass by sol–gel spin coating method. The homogeneous and crack-free BNT thin film was synthesized by cost effective solution sol gel coating method. The main crystal phase of the film was identified as Bi_1/2Na_1/2TiO₃. The BNT thin film which was coated 3 times and heat-treated at 700 °C had about 70% of transmittance in the ultra-violet visible (UV–VIS) light wavelength region. The calculated band gap energies from the UV transmittance spectra were 3.0 and 3.5 eV for indirect and direct transition, respectively and the refractive index of BNT thin film was 2.16 at 898 nm of wavelength. The hardness and elastic modulus of the film were about 9 and 136 GPa at 10 mN load, where the penetration depth was about 220 nm. BNT thin film showed the diffuse type of dielectric properties due to its Na⁺ and Bi³⁺ ions in A′_1/2A″_1/2BO₃-type perovskite structure and the dielectric constant was about 10 until 300 °C and showed maximum value at 550 °C, 450 at 1 kHz.     

Photocatalytic degradation of triazine dyes over N-doped TiO2 in solar radiation

Photocatalytic degradation of the reactive triazine dyes Reactive Yellow 84 (RY 84), Reactive Red 120 (RR 120), and Reactive Blue 160 (RB 160) on anatase phase N-doped TiO₂ in the presence of natural sunlight has been carried out in this work. The effect of experimental parameters like initial pH and concentration of dye solution and dosage of the catalyst on photocatalytic degradation have also been investigated. Adsorption of dyes on N-doped TiO₂ was studied prior to photocatalytic studies. The studies show that the adsorption of dyes on N-doped TiO₂ was high at pH 3 and follows the Langmuir adsorption isotherm. The Langmuir monolayer adsorption capacity of dyes on N-doped TiO₂ was 39.5, 86.0, and 96.3 mg g^?1 for RY 84, RR 120, and RB 160, respectively. The photocatalytic degradation of the dyes follows pseudo first-order kinetics and the rate constant values are higher for N-doped TiO₂ when compared with that of undoped TiO₂. Moreover, the degradation of RY 84 on N-doped TiO₂ in sunlight was faster than the commercial Aeroxide^® P25. However, the P25 has shown higher photocatalytic activity for the other two dyes, RR 120 and RB 160. The COD of 50 mg l^?1 Reactive Yellow-84, RR 120 and RB 160 was reduced by 65.1, 73.1, and 69.6 %, respectively, upon irradiation of sunlight for 3 h in the presence of N-doped TiO₂. The photocatalyst shows low activity for the degradation of RY 84 dye, when its concentration was above 50 mg l^?1, due to the strong absorption of photons in the wavelength range 200–400 nm by the dye solution. LC–MS analysis shows the presence of some triazine compounds and formimidamide derivatives in the dye solutions after 3 h solar light irradiation in the presence of N-doped TiO₂.     

Characterization of TiO2 nanotube arrays prepared via anodization of titanium films deposited by DC magnetron sputtering

Highly ordered TiO₂ nanotube arrays were fabricated on a conducting glass substrate in NH₄HF₂/glycol electrolyte via anodization of titanium film which was deposited by direct current magnetron sputtering (DCMS) at different temperatures. The results showed that Ti films with good homogeneity and high denseness could be formed under the conditions Ar pressure 0.35 Pa, direct current 3.5 A, and 2 h at 300 °C. Characterization of the TiO₂ nanotube arrays was investigated comparatively, by altering anodization time. The surface morphology of the samples changed as the anodization time was prolonged from 10 to 150 min at 30 V. The TiO₂ thin film was amorphous and could be transformed into anatase by annealing at 450 °C. On the basis of UV?Cvisible transmission spectra the bandgap of the thin film was calculated to be 3.12 eV, and its tail extended to 2.6 eV.     

Electrochromic properties of sputtered TiO2 thin films

TiO₂ thin films were deposited on ITO/Glass substrates by the rf magnetron sputtering in this study. The electrochromic properties of TiO₂ films were investigated using cyclic voltammograms (CV), which were carried out on TiO₂ films immersed in an electrolyte of 1 M LiClO₄ in propylene carbonate (PC). As- deposited TiO₂ thin film was amorphous, while the films post-annealed at 300~600°C contained crystallized anatase and rutile. With the increase of the annealing temperature, the surface roughness of film increased from 1.232 nm to 1.950 nm. Experimental results reveal that the processing parameters of TiO₂ thin films will influence the electrochromic properties such as transmittance, ion-storage capacity, inserted charge, optical density change, coloration efficiency and insertion coefficient.     

Preparation and nonlinear optical properties of Au nanoparticles doped TiO2 thin films

Nano-sized noble metal nanoparticles doped dielectric composite films with large third-order nonlinear susceptibility due to the confinement and the enhancement of local field were considered to be applied for optical information processing devices, such as optical switch or all optical logical gates. In this paper, sol–gel titania thin films doped with gold nanoparticles (AuNPs, ~10 nm in average size) were prepared. AuNPs were firstly synthesized from HAuCl₄ in aqueous solution at ~60 °C, using trisodium citrate as the reducing agent, polyvinylpyrrolidone as the stable agent; then the particle size and optical absorption spectra of the AuNPs in aqueous solutions were characterized by transmitting electron microscopy and UV–Vis–NIR spectrometry. Sol–gel 2AuNPs–100TiO₂ (in %mol) thin films (5 layers, ~1 μm in thickness) were deposited on silica glass slides by multilayer dip-coating. After heat-treated at 300–1,000 °C in air, the AuNPs–TiO₂ thin films were investigated by X-ray diffraction, scanning electron microscopy and atomic force microscopy. The nonlinear optical properties of the AuNPs–TiO₂ thin films were measured with the Z-scan technique, using a femtosecond laser (200 fs) at the wavelength of 800 nm. The third-order nonlinear refractive index and nonlinear absorption coefficient of 2AuNPs–100TiO₂ films were at the order of 10^?12 cm²/W, and the order of 10^?6 cm/W, respectively, and the third-order optical nonlinear susceptibility χ⁽³⁾ was ~6.88 × 10^?10 esu.     

Preparation and Characterization of Bismuth Doped TiO2 Thin Films

A series of Bismuth-doped titanium oxide (Bi-doped TiO₂) thin films on glass substrates have been prepared by sol-gel dip coating process. The prepared catalysts were characterized by XRD and XPS. The photocatlytic activity of the thin film catalysts was evaluated through the photodegradation of aqueous methyl orange under UV illumination. The experiments demonstrated that the Bi-doped TiO₂ prepared was anatase phase. The doped bismuth was in the 3⁺ oxidation state. The presence of Bi significantly enhanced the photocatalytic activity of TiO₂ films. At calcination temperature of 500°C, with doping concentration of 2 wt %, Bi-doped TiO₂ thin film showed the highest photocatalyic activity.     

Fabrication and characterization of TiO2 photocatalytic thin film prepared from peroxo titanic acid sol

A novel sol–gel technique using the PTA (peroxo titanic acid) sol as precursor for the fabrication of TiO₂ photocatalytic thin film is introduced in this paper. The peroxo titanic acid sol was synthesized from titanyl sulfate (TiOSO₄), ammonia and peroxide solution (H₂O₂). The transparent and porous TiO₂ thin film was prepared via a sol–gel technique using PTA sol and polyethylene glycol (PEG) as precursor and template, respectively. The TiO₂ thin film samples were characterized by the X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–visible spectrophotometry (UV–vis), X-ray photoelectron spectrum (XPS) and thermogravimetry and differential thermal analysis (TG-DTA) technique. The PTA sol displayed amorphous TiO₂ below 100 °C. The anatase phase formed at 200 °C to 700 °C. The crystallinity of anatase phase was improved with increasing temperature. The anatase crystals on the surface of TiO₂ film were strip-like, the size being about 100 nm in length and 40 nm in diameter. Addition of PEG to the PTA sol developed porous structures in the film and changed the size and shape of the particles. The surface of the film contained Ti, O and C elements and Na element that diffused into the film from the glass substrate. The photocatalytic performance of TiO₂ film was tested for the degradation of 10 mg/L methyl orange. The degradation of methyl orange solution reached 98.9% after irradiated for 180 min under UV light. The porous TiO₂ thin film exhibited high photocatalytic activity towards degrading methyl orange.     

Artificial photosynthesis by using chloroplasts from spinach adsorbed on a nanocrystalline TiO2 electrode for photovoltaic conversion

Photovoltaic conversion has been achieved by use of chloroplasts (photosynthetic organs) from spinach adsorbed on a nanocrystalline TiO₂ film on an indium tin oxide (ITO) glass electrode (chloroplast/TiO₂ electrode). The shape of the absorption spectrum of the chloroplast/TiO₂ electrode is almost the same that of a dispersion of the chloroplasts. Absorption maxima of the chloroplast/TiO₂ electrode observed at 430, 475, and 670 nm were attributed to carotenoid and chlorophyll molecules, suggesting that chloroplasts have been adsorbed by the nanocrystalline TiO₂ film on the ITO electrode. The photocurrent responses of chloroplast/TiO₂ electrodes were measured by using a solution of 0.1 M tetrabutylammonium hexafluorophosphate in acetonitrile as redox electrolyte in the presence or absence of water and 100 mW cm^?2 irradiation. The photocurrent of the chloroplast/TiO₂ electrode was increased by adding water to the redox electrolyte. The photocurrent responses of chloroplast/TiO₂ electrodes irradiated with monochromatic light (680 nm, the absorption band of photosystem II complexed with evolved oxygen) were measured by use of a solution of 0.1 M tetrabutylammonium hexafluorophosphate in acetonitrile as redox electrolyte in the presence or absence of water. A chloroplast/TiO₂ electrode photocurrent was observed only when the redox electrolyte containing water was used, indicating that the oxygen evolved from water by photosystem II in chloroplasts adsorbed by a nanocrystalline TiO₂ film on an ITO electrode irradiated at 680 nm is reduced to water by the catalytic activity of the platinum electrode. The maximum incident photon-to-current conversion efficiency (IPCE) was 0.8 % on irradiation at 670 nm.     

Fabrication of Ordered TiO2 Porous Thin Films by Sol-Dipping PS Template Method

Monolayer polystyrene spheres (∼400 nm) array templates were assembled orderly on clean glass substrates by dip-drawing method from emulsion of PS and porous TiO₂ thin films were prepared by using sol-dipping template method to fill TiO₂ sol into the interstices among the close-packed PS templates and then annealing to remove the PS templates. The effects of TiO₂ precursor sol concentration and dipping time in sol on the porous structure of the thin films were studied. The results showed pore size of the ordered TiO₂ porous thin film depended mainly on PS size and partly on TiO₂ sol concentration. The shrinkage of pore diameter was about 10% for 0.2 M and 20% for 0.4 M TiO₂ sol concentrations. X-ray diffraction (XRD) spectra indicated the porous thin film was anatase structure. The transmittance spectrum showed that optical transmittance of the porous thin film kept above 70% beyond the wavelength of 430 nm. Optical band-gap of the porous TiO₂ thin film (fired at 550^∘;C) was 3.12 eV.     

Synthesis and In Vitro Bioactivity of TiO2 Nanorods

Titanium dioxide (TiO₂) powders were synthesized by the hydrothermal method. The TiO₂ powders were composed of nanorods with dimensions of 10–18 nm and 60–180 nm in diameter and length, respectively. The in vitro bioactivity of the TiO₂ powders was examined by evaluation of hydroxyapatite (HAp) formation ability in simulated body fluid (SBF). The results showed that TiO₂ nanorods induced the formation of nanocrystalline HAp after soaking in SBF after 1 day rapidly. Our study indicates that TiO₂ nanorods are bioactive and might be used for preparation of new biomaterials.     

Efficient electrochromic performance of anatase TiO2 thin films prepared by nebulized spray deposition method

Anatase TiO₂ thin films with high optical modulation, better reversibility, fast switching time, and enhanced coloration efficiency were prepared by nebulized spray pyrolysis technique. X-ray diffraction study confirmed the formation of anatase phase TiO₂ in the present work. This inference was substantiated from the Raman active modes of A_1g, 2 B_1g, and 3 E_g corresponding to O–Ti–O bond in TiO₂. The PL emission peak observed at 400 nm is corresponds to the indirect transition (X_1b?→?Γ₃) from the conduction band to the valence band. The average reflectance of TiO₂ thin films was varied from 31 to 20%. The electrochemical study revealed the excellent performance of TiO₂ films with high optical modulation (ΔT?=?61%), fast switching kinetics (t _b ?=?1.6 s, t _c ?=?2.4 s), good coloration efficiency (100 cm² C^?1), and better reversibility (86%). The efficient electrochromic behavior of films may be due to the smooth microstructure nature, which provides an easy pathway for the diffusion and charge transfer process of Li⁺ ions in TiO₂ film matrix. The fast transfer of Li⁺ ion was realized from the electrochemical impedance spectroscopic measurement.     

Effect of initial precursor concentration on TiO2 thin film nanostructures prepared by PCVD system

TiO₂ thin film was prepared on Si substrate by plasma chemical vapor deposition (PCVD) system and the morphologies of TiO₂ thin film were controlled by adjusting the initial precursor concentration. As the initial titanium tetra-isopropoxide (TTIP) concentration increases in PCVD reactor, the shapes of TiO₂ particles generated in PCVD reactor change from the spherical small-sized particles around 20 nm and spherical large-sized particles around 60 nm to aggregate particles around 100 nm. The TiO₂ particles with different shapes deposit on the substrate and become the main building blocks of resulting TiO₂ thin film. We observed the TiO₂ thin film with smooth morphology at low initial TTIP concentration, granular morphology at medium initial TTIP concentration, and columnar morphology at high initial TTIP concentration. It is proposed that we can prepare the TiO₂ thin film with controlled morphologies in one-step process just by adjusting the initial precursor concentration in PCVD.     

Quantum dots co-sensitized solar cells: a new assembly process of CdS/CdSe linked to mesoscopic TiO2-nano-SiO2 hybrid film

A green and simple method was found to prepare CdS/CdSe co-sensitized photoelectrodes for the quantum dots sensitized solar cells application. All the assembly processes of CdS and CdSe quantum dots (QDs) were carried out in aqueous solution. CdS and CdSe QDs were sequentially assembled onto TiO₂-nano-SiO₂ hybrid film by two steps. Firstly, CdS QDs were deposited in situ over TiO₂-nano-SiO₂ hybrid film by the successive ionic layer adsorption and reaction (SILAR) process in water. Secondly, using 3-mercaptopropionic acid (3-MPA) as a linker molecule, the pre-prepared colloidal CdSe QDs (~3.0 nm) dissolved in water was linked onto the TiO₂-nano-SiO₂ hybrid film by the self-assembled monolayer technique with the mode of dropwise. The mode is simple and advantageous to saving materials and time. The results show that the photovoltaic performance of the cells is enhanced with the increase of SILAR cycles for TiO₂-nano-SiO₂/CdS photoelectrode. The power conversion efficiency of 2.15 % was achieved using the co-sensitization photoelectrode prepared by using 6 SILAR cycles of CdS plus CdSe (TiO₂-nano-SiO₂/CdS(6)/CdSe) under the illumination of one sun (AM1.5, 100 mW/cm²).     

Synthesis and visible light photocatalytic activity of Ag spot-coated TiO2–60 wt% SrO composite powders

Nano-sized TiO₂–60 wt% SrO composite powders were synthesized from titanium isopropoxide and Sr(OH)₂·8H₂O by use of a sol–gel method. Ag spot-coated TiO₂–60 wt% SrO composite powders containing 3, 5, or 7 wt% Ag were synthesized by hydrothermal-assisted attachment, by use of Ag hydrosol in a high-pressure bomb at 250 °C and 450 psi. Nano-sized Ag particles approximately 5–25 nm in diameter adhered to the TiO₂–60 wt% SrO₂ composite powders. The photocatalytic activity of Ag spot-coated TiO₂–SrO powders in the degradation of phenol showed that all were highly active when irradiated with UV light. TiO₂–60 wt% SrO composite powder spot-coated with 5 wt% Ag was more photocatalytically active under visible light than TiO₂–SrO composite powder.     

Effect of TiO2 nanostructure morphology on the performance of a photoelectrochemical cell of ITO/TiO2/electrolyte/platinum

The morphology of photovoltaic material is able to influence of the performance of photoelectrochemical cell. Polyvinylpyrrolidone (PVP), cetyltrimethylammonium bromide (CTAB), and hexamethylenetetramine (HMT) surfactant were used to modify the morphology nanostructure of TiO₂ films by a simple technique, namely, liquid phase deposition during their growth process. It was found that the untreated surfactant TiO₂ film produces the morphology with the mixture nanosphere and nanoflower. The film treated with PVP, CTAB, and HMT produce the nanostructure shape of nanoflower, nanowire, and nanorod, respectively. These TiO₂ samples were utilized as photovoltaic materials in a photoelectrochemical cell of ITO/TiO₂/electrolyte/platinum. It was found that the photovoltaic parameters such as short-circuit current density (J _sc), open-circuit voltage (V _oc) and fill factor are influenced by the morphology in terms of shape and particle size of the TiO₂ nanostructure. The cell utilizing the TiO₂ nanowire treated with PVP possesses the highest J _sc and V _oc of 0.100 mAcm^?2 and 0.44 V. The length of the TiO₂ nanowire is 6?±?2 nm, while the cell with the untreated surfactant TiO₂ sample demonstrates the lowest performance. It was also found that the J _sc and V _oc increase with the decrease in the length of the TiO₂ nanostructures. The smallest length of TiO₂ possesses the best interfacial contact at TiO₂/electrolyte containing iodide/triiodide redox couple. Thus, the redox reaction is optimized at this interface.     

Studies on photocatalytic activity of Ag/TiO2 films

Ag/TiO₂ photocatalytic films were produced by hybrid sol-gel method. The photocatalytic degradation of methyl orange (MO) in aqueous solution under 365 nm irradiation on TiO₂ and Ag/TiO₂ thin films was investigated. The state and amount of Ag species within the film and the enhancement mechanism of photocatalytic activity of Ag/TiO₂ were discussed. With a loading molar ratio of Ag/Ti = 0.135 in TiO₂ film, the maximum catalytic efficiency was observed. __________ Translated from Journal of Beijing Normal University (Natural Sciences), 2005, 41(6) (in Chinese)     

Low-temperature synthesis of photocatalytic TiO2 thin film from aqueous anatase precursor sols

Anatase TiO₂ sols (RS) were synthesized by peptizing the hydrolysis of titanyl sulfate in abundant hydrogen peroxide solution and subsequent reflux to enhance crystallization. The influences of various reflux time on crystallinity, morphology, and size of the obtained TiO₂ sol and dried TiO₂ film particles were investigated. At room temperature, crystalline TiO₂ thin film was deposited on glass silde from the as prepared TiO₂ sol by dip-coating method. No further thermal posttreatment was required to eliminate organics from the film or to induce titania crystallization. TiO₂ thin film on substrates could be thickened by means of consecutive dip-coating process. Titania film thus obtained was transparent and showed proper adherence. The photocatalytic activities of the TiO₂ thin film was assessed by the degradation of methyl orange in aqueous solution. The preparation process of photocatalytic TiO₂ thin film was quite simple and a low-temperature route.