DSC and morphological studies on the crystallization behavior of β-nucleated isotactic polypropylene composites filled with Kevlar fibers

The crystallization behavior of β-nucleated isotactic polypropylene (PP) composites filled with Kevlar fibers (KFs), as well as that of non-nucleated PP/KF composites for comparison, was investigated using differential scanning calorimetry (DSC) and polarized optical microscopy (POM). The morphological observations revealed that the KF addition could induce thick α-transcrystalline layer around their surfaces in PP/KF composites, while no obvious transcrystalline layer could be detected in β-nucleated PP/KF composites. Detailed DSC investigations suggested that for the PP/KF composites, the dominant modification was α-form, and the crystallization process of matrix was promoted by KF addition, as illustrated by faster isothermal crystallization rate, shorter induction time, and higher crystallization temperature. However, for β-nucleated PP/KF composites, the main modification was β-form, and their crystallization characteristics were independent of KF addition, indicating that the α-nucleating effect of KFs was absent in this system. The DSC results were confirmed by further rheological and wide angle X-ray diffraction (WAXD) studies. The mechanism of the formation of transcrystalline layer was also discussed.     

Characterization of Silver Flake Lubricants

There is a thin layer of organic lubricant on commercial silver (Ag) flakes that are widely used as the fillers in electrically conductive adhesives (ECAs). This lubricant layer highly affects the properties such as conductivity of the ECAs. Therefore, understanding the behavior of Ag flake lubricant layer is essential for developing high performance ECAs. This work is aimed at studying the chemical nature of the lubricant layer, interaction between the lubricant layer and Ag flakes, and thermal behavior of the lubricants during heating. A blank Ag powder is ball-milled into Ag flakes with five fatty acids that have different carbon–hydrogen chain length as lubricants. After lubrication, the Ag flakes are studied using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and thermogravimetry (TG), and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). It is found that (i) Ag flakes lubricated with fatty acids of different chain lengths have exothermic DSC peaks and mass losses at different temperatures, (ii) the lubricant layer on the lubricated Ag flake surfaces is a salt formed between the acid and Ag, and (iii) exothermic DSC peaks (in air) of a lubricated Ag flake is probably due to the oxidation of lubricant layer on the Ag flake surface. This revised version was published online in July 2006 with corrections to the Cover Date.     

Physicochemical analyses of phase transition and dehydration processes of a new oral 1beta-methylcarbapenem antibiotic agent,CS-834

The characterizations of the anhydrate (A-form), monohydrate (B1-form), and dihydrate (B2-form) of CS-834 were investigated by powder X-ray diffraction, differential scanning calorimetry (DSC), thermogravimetry-differential thermal analysis (TG-DTA), infrared spectroscopy, and Karl Fischer moisture titration. The typical DSC curve of the B2-form showed five endothermic peaks at 35.0, 46.4, 56.2, 99.2, and 190.4 degrees C and an exothermic peak at 123.4 degrees C. In TG-DTA analysis, the three peaks at 35.0, 46.4, and 56.2 degrees C had a total weight loss of 7.3%, corresponding to the release of two water molecules. From morphological observation under thermomicroscopy, the endothermic peak at 99.2 degrees C was attributed to the melting of the dehydrous crystals (B0-form) and the exothermic peak at 123.4 degrees C to the recrystallization to the A-form crystals. The endothermic peak at 190.4 degrees C was due to the melting of the A-form crystals. After incubation for 6.0 h at 35, 50, 60, and 80 degrees C, the powder X-ray diffraction patterns of the B2-form indicated that it was converted into the A-form via the B1-form and B0-form. Thus CS-834 exists in homologous hydrous crystal forms in multiple-phase transformations with the dehydration of two water molecules.     

Structure,hydrophilicity and corrosion resistance of sol–gel derived Ag-containing TiO2 film on plasma nitrided 316L stainless steel

Pure and Ag-containing TiO₂ films (Ag/Ti = 3.3 at.%) are coated on plasma nitrided 316L stainless steel by sol–gel method for biomedical applications. The addition of Ag does not cause obvious change in TG–DSC curves of the dried gels. The rough surface generated by plasma nitriding and the addition of Ag improve structural integrity of the TiO₂ films. X-ray diffraction reveals N loss and oxidation of the nitride layer during calcination treatment, and peaks of Ag or its oxides are not detected. X-ray photoelectron spectroscopy analysis indicates that Ag presents as metallic state in the film. Water contact angles of the coating samples decrease with UV irradiation treatment. The potentiodynamic polarization tests in a Ca-free Hank’s balanced salt solution show that the TiO₂ coated samples have decreased corrosion resistance due to N loss and oxidation of the nitride layer. The methods for crystallization of TiO₂ gel layers with minimized or avoided structural changes of the nitride layer will be tried in order to improve corrosion resistance of the duplex treated 316L stainless steel.     

Ag/ZnO/ZnSe三元异质结的合成及其可见光光催化性能

以Ag纳米线为模板,通过两步水浴法合成了Ag/ZnO/ZnSe三元异质结光催化材料。利用场发射扫描电子显微镜(FESEM)、X射线能谱仪(EDS)、X射线衍射仪(XRD)以及透射电子显微镜(FETEM)对样品的形貌和结构进行了表征。结果显示,Ag/ZnO/ZnSe三元异质结为蠕虫状的Ag/ZnO二元异质结外镶嵌着ZnSe小颗粒。在可见光下,对比纯Ag纳米线、纯ZnO纳米球、Ag/ZnO异质结对罗丹明B的可见光降解效率,结果发现Ag/ZnO/ZnSe异质结表现出了更高的光催化效率。其光催化性能的提高主要是由于Ag/ZnO/ZnSe异质结的作用促使电子空穴对的分离,降低了电子空穴对的复合机率,从而提高了材料的光催化效率。     

纳米Ag/CNTs复合材料的制备、表征及对环三亚甲基三硝胺热分解的影响

采用银镜法和水热法制备了两种纳米Ag/CNTs(碳纳米管)复合材料, 利用傅里叶变换红外(FTIR)光谱、粉末X射线衍射(XRD)、透射电子显微镜(TEM)、扫描电子显微镜及能量散射光谱仪(SEM-EDS)对复合物的物相、组成、形貌和结构进行分析表征, 并运用差示扫描量热法(DSC)研究了纳米Ag/CNTs 复合材料对环三亚甲基三硝胺(RDX)热分解特性的影响. 结果表明: 纳米Ag 以10-80 nm的不规则球形“粘附”于纳米CNTs 表面,分散较均匀, 水热法制得的复合物表面纳米Ag较大、且负载的Ag粒子较多; 纳米Ag/CNTs 复合材料的加入改变了RDX的热分解过程, 使原有占主导的液相分解变为二次的气相反应加剧, RDX主分解峰形发生了明显的改变; 纳米Ag/CNTs 复合材料对RDX热分解的催化主要表现为分解温度的降低.     

Enhanced β phase of polyvinylidene fluoride with addition of polyamide 6: role of interfacial interactions

In this study, the polymer blends composed of polyvinylidene fluoride (PVDF) and polyamide 6 (PA6) were prepared via precipitation method, and then, the effects of PA6 on the crystallization behavior of PVDF, including the polymorphism and crystallization kinetice, were systematically investigated. For this aim, time-resolved Fourier transform infrared spectroscopy, X-ray diffraction, and differential scanning calorimeter were utilized to study the influence of PA6 on crystallization behavior of PVDF. Furthermore, the morphologic images from scanning electron microscopy also supply the corresponding evidences. The results obtained shows that PA6 is immiscible with PVDF, while the PA6 component could form polar environment around the PVDF segment which is conducive to the formation of β phase of PVDF. In addition, calorimetric studies via DSC on the non-isothermal crystallization behavior and non-isothermal crystallization kinetics demonstrated conclusively that PA6 segments could effectively hinder the subsequent PVDF crystallization process because of the interfacial hydrogen bonds and incompatibility between PVDF and PA6.     

莫来石抗氧化外涂层的制备及抗氧化性能

以莫来石粉体(3Al2O3·2SiO2)为原料,采用水热电泳沉积法在C/C-SiC复合材料表面制备了莫来石外涂层。借助XRD和SEM等对涂层的晶相组成和显微结构进行了表征。研究了水热沉积电压对莫来石外涂层相组成、形貌及高温抗氧化性能的影响。结果表明:外涂层主要由莫来石晶相组成。当沉积电压控制在120~180 V范围内时,莫来石外涂层的致密程度、厚度及抗氧化性能随着沉积电压的升高而提高。当沉积电压达到210 V时,制备的外涂层出现疏松、裂纹等缺陷,抗氧化性能减弱。抗氧化测试表明与包埋法制备的SiC-C/C涂层试样相比,莫来石-SiC-C/C涂层试样的抗氧化性能明显提高。当沉积电压为180 V时,制备的复合涂层试样可在1500℃的空气气氛下有效保护C/C复合材料164 h,其失重仅为1.75%。     

水热法合成多孔Ag_2S敏化二氧化钛催化剂及其可见光催化活性(英文)

Porous Ag2S sensitized TiO2 catalysts were synthesized by the hydrothermal process.The crystallization and porous structure of the Ag2S/TiO2 composite photocatalysts were investigated by X-ray diffraction,scanning electron microscopy with energy dispersive X-ray analysis,UV-Vis diffuse reflectance spectroscopy,and N2 adsorption.The Ag2S/TiO2 composites were mainly composed of anatase TiO2 and acanthite Ag2S.The absorption edge wavelengths of TiO2 and the Ag2S/TiO2 composite prepared with 3 mmol Na2S.5H2O were 400 and 800 nm,respectively,that is,the absorption edge of the composite had a pronounced red shift.The photocatalytic activity under visible light was investigated by the degradation of methylene blue with a UV-Vis spectrophotometer.The photocatalytic activities under visible light of the Ag2S/TiO2 photocatalysts were much higher than that of TiO2.     

Ag2S/Al2O3纳米复合物的水热合成及表征

采用水热技术结合煅烧的方法,成功制备了Ag2S/Al2O3纳米复合物。 通过SEM、EDX、XRD等测试技术对产品进行了表征,证明得到的产品是Ag2S/Al2O3纳米复合物;无孔Al2O3和多孔Al2O3作反应模板得到的复合物的形态和分布不同。     

Solution behavior and solid phase transitions of quaternary ammonium surfactants with head groups decorated by hydroxyl groups

Hydrogen bonds are strong intermolecular interactions, which are very important in molecular aggregation and new phase formation. Three long-chain quaternary ammonium surfactants, N,N-diethyl-N-(2-hydroxyethyl)-N-octadecylammonium bromide with one hydroxyl group, N-ethyl-N,N-bis (2-hydroxyethyl)-N-octadecylammonium bromide with two hydroxyl groups and N,N,N-tris (2-hydroxyethyl)-N-octadecylammonium bromide with three hydroxyl groups, abbreviated as SHQ, DHQ, and THQ, respectively, were synthesized in this work. Their solution behavior and solid phase transitions were investigated by surface tension, differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarizing optical microscopy (POM), and Infrared (IR) spectroscopy. The hydrogen bonds introduced by the substituted hydroxyl groups promoted surfactant adsorption at the air/water interface and aggregation in solution. In the crystal state, an increased number of hydroxyl groups caused a larger tilt angle of the long axis of surfactant molecules with the layer normal. Above certain temperatures, SHQ and DHQ formed highly ordered smectic T and smectic A phases while THQ only formed less ordered smectic A phase. The weakened electrostatic attractions between opposite ions and the thicker polar sublayers of mesophases caused by the enhanced number of hydrogen bonds are responsible for the mesophase formation and transition of these surfactants.     

Uniform silver nanoparticles on tunable porous N‐doped carbon nanospheres for aerobic oxidative synthesis of aryl nitriles from benzylic alcohols

Tunable N‐doped carbon nanospheres from sucrose as carbon source and Tris(2‐aminoethyl)amine (TAEA) as nitrogen source by a simple and easily reproducible method were prepared. It was demonstrated that the tunable N‐doping of carbon spheres could be realized by altering the ratio of TAEA in the raw materials. The content of doped nitrogen, surface area, pore volume and pore size of carbon nanospheres were increased with the increasing of TAEA amount in the hydrothermal process. Prepared N‐doped carbon nanospheres act as solid ligand for anchoring of Ag NPs which generated via chemical reduction of Ag ions. Benzylic alcohols and aldehydes were converted into the aryl nitriles by using Ag/N‐CS‐1 nanospheres as the catalyst and O₂ as the oxidant, efficiently. This catalyst was stable and could use for 6 successful runs.     

Influence of nucleating agent on the formation and enzymatic degradation of poly(butylene adipate) polymorphic crystals

The effects of nucleating agent multimethyl-benzilidene sorbitol (TM6) on crystallization and morphology of poly(butylene adipate) (PBA) with polymorphic crystal structures were studied by means of differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD) and polarized optical micrographs (POM). In addition to the heterogeneous nucleation, TM6 changes the formation conditions of PBA polymorphic crystals. The addition of TM6 is favorable for the formation of PBA α-form crystals, resulting in the morphological changes from spherulites to interpenetrated fibrils. The influences of TM6 on enzymatic degradation of PBA were studied in terms of the morphological change and weight loss. The results indicate that the α-form crystals induced by TM6 show much slower degradation rate. This work provides an efficient method to control the polymorphic crystal structure and further to regulate the biodegradation rate of polymer materials through modulating the homogeneous and heterogeneous nucleation modes by adding nucleating agents.     

MORPHOLOGY AND MECHANICAL PROPERTIES OF POLYPROPYLENE WITH in situ FORMED POLYAMIDE-6 FIBRILS

in situ Fibril formation of polyamide-6(PA6)in isotropic polypropylene(iPP)was first fabricated using a slit die extrusion and hot stretching process.Then the prepared materials were subjected to injection molding in the temperature range higher than the melting temperature of iPP but lower than that of PA6.The obtained injection-molded samples were characterized via scanning electron microscopy(SEM),differential scanning calorimetry(DSC)and two-dimensional wide- angle X-ray scattering(2D-WAXS).Mechanical properties were also investigated.The SEM result shows that the optimum fibril formation could be only achieved in the range of 20 wt% to 30 wt% of PA6 content for the studied system.The fibril morphology changes along the sample thickness in the injection-molded bars.The fibril morphology in the skin layer was better than that in the core layer.2D-WAXS results showed that the orientation of PP decreased with the increase of PA6 content,which indicated that the orientation of PP was confined by PA6 fibrils.Combined consideration of mechanical properties and morphology indicates that only PP/PA6 composites with 20 wt% of PA6 content show better properties because of the better fibril morphology and PP chain orientation.     

PANI-DBSA/PAN共混体系的相容性及导电性能

以三氯甲烷/二甲基亚砜为混合溶剂,采用溶液共混的方法制备PANI-DBSA/PAN导电薄膜.采用扫描电镜、差示扫描量热仪、红外光谱及广角X射线衍射分析研究了共混体系的相容性及相态结构.结果表明,PANI-DBSA在PAN基体中分布均匀,聚集尺寸为纳米级,其较均匀的分布及较小的聚集尺寸使其出现较低的逾渗阈值(低于4%);PANI-DBSA/PAN的共混体系只有一个玻璃化转变温度,居于纯PAN和PANI-DBSA之间,表明两者之间具有良好的相容性;FTIR分析证实PANI-DBSA与PAN之间存在氢键相互作用,氢键发生在PANI-DBSA的氨基与PAN共聚物中的羰基之间,这两种聚合物之间的氢键相互作用是导致PANI-DBSA与PAN之间良好相容性的内因.     

Crystal habit modifications of imatinib mesylate under various precipitation conditions

Abstract  

Crystals of the α-form of imatinib mesylate with various habits (e.g., polyhedral-like and plate-like) were prepared from various organic solvents (e.g., butyl lactate, 4-methyl-2-pentanone, 2-methyl-2-butanol, 2-isopropoxyethanol, propyl ether) by several precipitation methods. The methods provide imatinib mesylate in a non-needle-shaped crystalline α-form. The crystal modification was identified by hot-stage microscopy, scanning electron microscopy, differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and X-ray powder diffraction (XRPD). The analyses by DSC, IR, and XRPD indicate that imatinib mesylate crystals with various habits have the same crystal structure. The plate-like habit has been also observed in the system where the organic solvent acts as a precipitant.     

ESIPT-regulated Mechanoresponsive Luminescence Process byIntroducing Intramolecular Hydrogen Bond in NaphthalimideDerivatives#br#

Herein, two compounds, 4-2′-hydroxybenzylidenehydrazinyl-N-butyl-1,8-naphthalimide(BN-1) and 4-benzylidenehydra-zinyl-N-butyl-1,8-naphthalimide(BN-2), were synthesized to explore the hydrogen bonding effect on mechanoresponsive luminescent(MRL). The results showed that compound BN-1 exhibited strong emission in solution and solid-state compared with compound BN-2. After grinding, the emission intensity of compound BN-1 sharply decreased by as much as 15 times with an obvious red-shift from 552 nm to 577 nm. The control compound BN-2, by contrast, did not change so much before and after grinding. Single crystal analysis suggests that BN-1 molecule formed strong intramolecular interaction via ―N=N···H―O hydrogen bond with a distance of 0.2632 nm. An excited-state intramolecular proton transfer(ESIPT) based fluorophore featured this intramolecular hydrogen bond. The intramolecular hydrogen bond as well as other intermolecular interactions can rigidify the molecular conformation of compound BN-1 in solid-state, and thus suppress the nonradiative pathways, resulting in strong emission. These intra- and intermolecular interactions were destroyed by mechanical stimuli, accompanied by molecular conformation change that decreases the luminescence and blocks the ESIPT process. The MRL process was also demonstrated by scanning electron microscopy and powder X-ray diffraction. The molecular stacking mode changed from crystalline to a disordered amorphous state after grinding.     

Crystal Structure of a Linear Ag(Ⅰ) Complex with Niflumic Acid and Its Fluorescent Property

A novel Ag(Ⅰ) complex AgH(Nifa)2 1 (C26H17AgF6N4O4, Mr = 671.31) was synthe- sized through hydrothermal reaction of Ag2SO4 and Niflumic acid (HNifa), and characterized by single-crystal X-ray determination, IR and fluorescent spectra. Crystal data for 1: monoclinic, space group C2/c, with a = 9.5446(16), b = 12.3203(16), c = 21.056 (3) (A), β = 98.075(2)o, V = 2451.5(6) (A)3, T = 293(2) K, Z = 4, Dc = 1.819 g/cm3, F(000) = 1336, μ = 0.912 mm-1, S = 1.001, (Δρ)min = -0.849, the final R = 0.0391 and wR = 0.1286. The local geometry around the central metal Ag(Ⅰ) ion is linear. Two carboxylic acids of neighboring ligands sharing one hydrogen atom by two hydro- gen bonds result in the formation of an infinite hydrogen-bonded chain. Solid-state fluorescence of 1 at room temperature shows that the maximal emission peak occurs in 439 nm.     

Ag负载CdMoO4光催化剂的制备及其催化性能

采用硼氢化钠还原法制备了Ag负载CdMoO₄光催化剂。运用X射线粉末衍射（XRD）、扫描电镜（SEM）和透射电镜（TEM）等测试手段对催化剂的组成和结构进行了表征;采用紫外-可见漫反射光谱（UV-Vis DRS）和X射线光电子能谱（XPS）等技术对催化剂的光响应和表面状态进行了分析,考察了不同Ag负载量对CdMoO₄紫外光降解罗丹明B和可见光选择性氧化苯甲醇性能的影响。结果表明,与CdMoO₄相比,Ag/CdMoO₄具有更高的光催化活性。利用活性物种捕获实验探讨其光催化降解过程的反应机理,实验结果显示O₂^-·和·OH是光催化降解过程的主要活性物种。     

Some novel disaccharide-derived liquid crystals

Some novel disaccharide-derived amphiphiles, in which the hydrophobic long chain alkyl group and an alpha -D-glucose moiety are separated by a hydrophilic five carbon spacer or a hydrophobic furan residue, were investigated as to their mesomorphic properties using DSC, thermomicroscopy and various X-ray methods. All compounds exhibit a smectic A phase, characterized by aggregation to a bilayered S structure. The layer thickness d , measured by A X-ray, correlates with the presence of polar d and non-polar moieties, adjoining molecules interacting via hydrogen bonding. Based on the known structural concepts for sugar-derived liquid crystals, a model is suggested to account for the observed S mesomorphic behaviour of two N -alkanoyl derivatives of (glucosylox dymethylfuryl) methylamine, i.e. species in which sugar and long chain fatty acid are separated by a quasi-aromatic furan residue, is unusual, as different X-ray methods invariably give the same odd indicative of a smectic layer thickness of three to four molecules. layer arrangement. The A d -value indicative of a smetic layer thickness of three to four molecules.