电子束泵浦KrF激光放大器增益与吸收的测量

为研制百焦耳级ＫｒＦ激光放大器，发展ＭＯＰＡ系统，我们用自探测法在百焦耳级电子束泵浦ＫｒＦ激光装置上进行了激光放大器的增益与吸收的测量。泵浦率约为０．６７ＭＷ／ｃｍ￣２，激光介质为８９．６％Ａｒ：１０％Ｋｒ：０．４％Ｆ＿２的混合气体，总气压０．２５ＭＰａ，实验测得激光放大器的小信号增益系数ｇ＿０＝６．６％ｃｍ￣（－１）、非饱和吸收系数α＿ｎ＝０．９３％ｃｍ￣（－１）、饱和光强Ｉ＿ｓ＝２．５ＭＷ／ｃｍ￣２。     

电子束泵浦KrF激光放大器增益与吸收的测量

为研制百焦耳级ＫｒＦ激光放大器，发展ＭＯＰＡ系统，我们用自探测法在百焦耳级电子束泵浦ＫｒＦ激光装置上进行了激光放大器的增益与吸收的测量。泵浦率约为０．６７ＭＷ／ｃｍ￣２，激光介质为８９．６％Ａｒ：１０％Ｋｒ：０．４％Ｆ＿２的混合气体，总气压０．２５ＭＰａ，实验测得激光放大器的小信号增益系数ｇ＿０＝６．６％ｃｍ￣（－１）、非饱和吸收系数α＿ｎ＝０．９３％ｃｍ￣（－１）、饱和光强Ｉ＿ｓ＝２．５ＭＷ／ｃｍ￣２。     

堆泵浦^3He—Ar—Xe体系的激光原理性实验

介绍了在ＣＦＢＲ－Ⅱ脉冲堆上进行的￣３Ｈｅ─Ａｒ─Ｘｅ体系的激光演示实验。当热中子注量率６×１０￣（１４）／ｃｍ￣２·ｓ，气体组配￣３Ｈｅ：Ａｒ：Ｘｅ＝３４．７：３４．７：０．２６７（ｋＰａ）时，获得波长λ＝１．７３μｍ、脉宽（ＦＷＨＭ）平均值７３８μｓ、峰值功率为毫瓦级的激光输出。同时对测得的光信号及其特性进行了分析。     

37 fs、 0.94 μm钛宝石自锁模激光器的研究

报道了低增益区Ｔｉ＾３＋：Ａｌ２Ｏ３红外飞秒激光器的连续及自锁模运转情况,采用四镜折叠像散补偿腔,对于连续波运转,泵浦阈值功率为５．８Ｗ,其调谐范围为０．９－０．９７μｍ。     

HL—1M装置欧姆等离子体实验的初步分析

从１９９４年１０月２４日开始，对ＨＬ－１Ｍ装置进行欧姆加热等离子体的调试实验，获得了Ｉｐ＝３１０ｋＡ，ｑｎ＜２．５，ｎｃ＝３×１０＾１３ｃｍ＾－３，Ｔｃ（０）＞１ｋｅＶ，Ｔｉ（０）＞０．５ｋｅＶ和τＥ≈１０ｍｓ的平衡稳定等离子体。本文简述了ＨＬ－１Ｍ装置及其诊断等的实验结果进行了初步分析和讨论。     

堆泵浦~3He－Ar－Xe体系的激光原理性实验

介绍了在ＣＦＢＲ－Ⅱ脉冲堆上进行的￣３Ｈｅ─Ａｒ─Ｘｅ体系的激光演示实验。当热中子注量率６×１０￣（１４）／ｃｍ￣２·ｓ，气体组配￣３Ｈｅ：Ａｒ：Ｘｅ＝３４．７：３４．７：０．２６７（ｋＰａ）时，获得波长λ＝１．７３μｍ、脉宽（ＦＷＨＭ）平均值７３８μｓ、峰值功率为毫瓦级的激光输出。同时对测得的光信号及其特性进行了分析。     

飞秒光脉冲光纤放大增益特性的实验研究

报道了掺Ｅｒ＾３＋光纤激光器输出１．５３１μｍ波长飞秒激光脉冲增益放大的实验研究结果,将自起振相加脉冲摹参Ｅｒ＾３＋光纤激光器输出的飞秒激光脉冲注入掺Ｅｒ＾３＋光纤放大器中进行放大,分别采用正向和逆向抽地这的方式,得到了最高放大倍数５５倍（１７．４ｄＢ）和６４倍（１８．１ｄＢ）的增益,对应的最大单脉冲能量（峰值功率）分别为０．３８４ｎＪ（７５２Ｗ）０．４５２ｎＪ（１２９５Ｗ）,脉冲重复率为２０．８     

堆泵浦^3He—Ar—Xe激光实验的放大管研制

介绍了堆泵浦￣３Ｈｅ－Ａｒ－ｘｅ激光实验中放大管的设计及混合气的组成。经聚乙烯慢化体慢化后的ＣＦＥＲ－Ｈ脉冲堆的热中子注量率为６×１０～（１４）ｎ／ｃｍ￣２·ｓ，根据慢化体结构设计了内充气体组份为￣３Ｈｅ：Ａｒ：Ｘｅ＝３４．７：３４．７：０．２６７，６ｏｏｍｍ×Φ３４ｍｍ的放大管，在约１．４×１０￣（１６）裂变每脉冲下进行￣３Ｈｅ－Ａｒ－Ｘｅ（λ＝１．７３μｍ）激光激射实验，获得毫瓦级功率输出。     

外腔输出的连续波化学氧碘激光器

研制了一台采用外腔输出的小信号增益为１．６×１０￣（－３）ｃｍ￣（－１）的连续波化学氧碘激光器，在氯流率为３０ｍｍｏｌ／ｓ，Ｉ＿２流率为０．３ｍｍｏｌ／ｓ，腔压为２００Ｐａ时首次获得了半外腔１７８ｗ和中外腔７０．４Ｗ的１．３１５μｍ高功率线偏振光输出。     

二极管激光侧面泵浦腔内倍频Nd：YAG板条激光器研究

用准连续６０Ｗ的二极管激光列阵侧面泵浦“之”字形Ｎｄ：ＹＡＧ板条激光器，当泵浦功率为４５Ｗ，脉宽为４００μｓ时，得到３．５ｍＪ的激光输出。用ＫＤ＊Ｐ电光开关调Ｑ，得到１８ｎｓ（ＦＷＨＭ）、２ｍＪ的脉冲激光输出，用ＫＴＰ晶体作腔内倍频，得到１５ｎｓ、０．８５ｍＪ的二次谐波激光输出。在腔内无调Ｑ元件且腔长小于５ｃｍ时，于近阈值处得到单频绿光输出，而当泵浦功率稍大，腔内有数个纵模振荡时，观察到激光的反相态，并用数值模拟的结果对此作了解释。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.