Contribution of power on cell adhesion using atmospheric dielectric barrier discharge (DBD) plasma system

This study examined the effect of the treatment power on the enhanced cell attachment and proliferation on poly ε-caprolactone (PCL) films treated with atmospheric plasma using a dielectric barrier discharge method (AP-DBD). The peak intensities of the –CH, CO, –OH and –COO vibration modes, and binding energies of carbon and oxygen of the AP-DBD treated-PCL film increased with increasing plasma treatment power. The surfaces of the AP-DBD treated-PCL films were also examined for their in vitro cell adhesion properties using human prostate epithelial cells. The results showed that the level of cell attachment and proliferation on the AP-DBD treated-PCL film was ten times better than that observed on the untreated-PCL films.     

Jet noise control using the dielectric barrier discharge plasma actuators

We study experimentally how plasma actuators operating on the basis of surface barrier high-frequency discharge affect jet noise characteristics. The results of investigations of air jets (100?C200 m/s) have demonstrated that the studied plasma actuators have control authority over the noise characteristics of these jets. An actuator??s effect on the jet in the applied configuration is related to acoustic discharge excitation and to a large extent is similar to the well-known Vlasov-Ginevsky effect. It has been shown that jet excitation in the case of St ?? 0.5 using the barrier-discharge plasma actuator leads to broadband amplification of jet sound radiation. The jet excitation in the case of St > 2 leads to broadband noise reduction if the action is sufficiently intensive.     

Forebody asymmetric vortex control with extended dielectric barrier discharge plasma actuators

Plasma control of forebody asymmetric vortices is mostly achieved by means of dielectric barrier discharge(DBD)plasma actuators. However, DBD actuators suffer from some disadvantages such as a weak induced body force, a singledirection induced jet, and an unclear control mechanism. We carry out wind tunnel experiments involving the forebody vortex control of a slender body at high angles of attack using an innovative extended DBD actuator, which has a stronger capacity to induce an electric wind than a DBD actuator. Through synchronous measurements of the pressure distribution and particle image velocimetry(PIV), the spatiotemporal evolution of the dynamic interactions between plasma-actuationinduced vortices and forebody asymmetric vortices is analyzed. The influence of plasma discharge on the boundary layer separation around a slender body and the spatial topological structures of asymmetric vortices are further surveyed, as the optimized actuation parameters. Extended DBD actuators are found to be more capable of controlling asymmetric vortices than DBD actuators, and a linear proportionality of the sectional lateral force versus the duty ratio is achieved.There exists an optimal normalized reduced frequency( f+= 2π fpd/U∞= 2.39) for asymmetric vortex control under the present experimental conditions. The research results can provide technical guidance for the control and reuse of forebody asymmetric vortices.     

Uniformity analysis of dielectric barrier discharge (DBD) processed polyethylene terephthalate (PET) surface

A dielectric barrier discharge (DBD) plasma, operating in air at atmospheric pressure, has been used to induce changes in the surface properties of polyethylene terephthalate (PET) films. The effects that the key DBD operating parameters: discharge power, processing speed, processing duration, and electrode configurations, have on producing wettability changes in the PET surface region have been investigated. The approach taken involves the application of an Taguchi experimental design and robust analysis methodology. The various data sets obtained from these analyses have been used to studies the effect of the operating parameters on the surface uniformity and efficiency of the said treatment.In general, the results obtained indicate that DBD plasma processing is an effective method for the controlled surface modification of PET. Relatively short exposures to the atmospheric pressure discharge produces significant wettability changes at the polymer film surface, as indicted by pronounced reductions in the water contact angle measured. It was observed that the wettability of the resultant surface shows no significant differences in respect to orientation parallel (L-direction) or perpendicular (T-direction) to the electrode long axis. However, there was significant differences between the data obtained from these two orientations. Analysis of the role of each of the operating parameters concerned shows that they have a selective effectiveness with respect to resultant surface modification in terms of uniformity of modification and wettability. The number of treatment cycles and the electrode configuration used were found to have the most significant effects on the homogeneity of the resultant PET surface changes in L- and T-orientation, respectively. On the other hand, the applied power showed no significant role in this regard. The number of treatment cycles was found to be the dominant factor (at significance level of 0.05) in respect of water contact angle changes at the processed PET surface in both orientations. The driven metal electrodes (stainless steel or aluminium) were apparently superior to the driven dielectric electrode (ceramic or quartz) configurations. The grounded electrode in each case was a silicon rubber-covered aluminium plate (see later). The nature and scale of the surface changes that originate from the various processing conditions employed have been considered so as to determine the optimum treatment conditions in respect of processing outcomes, properties and any orientation dependence. Thus, it was revealed that higher processing speeds and longer processing durations are key for uniformity along the electrode axial orientation, while lower processing speeds and short exposure durations are key considerations, in the corresponding perpendicular orientation. In general, longer processing durations (low processing speeds and a high number of treatment cycles) and higher plasma powers induced greater changes in the surface wettability of the PET, as demonstrated by the observed water contact angles. This behaviour is taken to indicate that different combinations of DBD operating parameters and electrodes produce discharge conditions that can result in different plasma chemical processes in respect of uniformity, treatment efficiency and orientation dependence.     

Triboelectrification of granular insulating materials as affected by dielectric barrier discharge (DBD) treatment

The aim of this paper is to point out the influence of dielectric barrier discharge treatment on tribocharging of granular insulating materials. Particles of Polyvinyl Chloride (PVC) and Polypropylene (PP) were subjected to an AC dielectric barrier discharge (DBD) plasma treatment in ambient airprior to tribocharging in a vibratory device. The charge to mass ratio was measured for treated and untreated materials. Electrostatic separation of a mixture of granular materials (PVC and PP) to measure the effectiveness of DBD treatment was evaluated by processing treated and untreated PVC/PP granular mixtures in a free-fall electrostatic separator. The obtained results clearly indicate that DBD has the capability to influence surface charging proprieties of polymer granular materials. In case of short treatment time, typically less than 3 s, a marked increase in the charge to mass ratios was observed for both PVC (about 35%) and PP (roughly 45%). In the same way, the quantity of DBD-treated materials, recovered after electrostatic separation, was increased by about 104% and 30% for PVC and PP, respectively, as compared to untreated case. The DBD treatment time is a key factor to increase the tribo electric effect.     

The effect of air plasma on barrier dielectric surface in dielectric barrier discharge

Barrier dielectric is an important part of atmospheric pressure dielectric barrier discharge (AP-DBD), which partly affects discharge characteristics. Conversely, discharge plasma also has influence on dielectric surface properties. To investigate this influence, some experiments were carried out on a home-built AP-DBD system with glass plate as barrier dielectric. Surface wettability was evaluated by water contact angles on a drop shape analysis system. The morphologies and chemical compositions of the glass sample surfaces were observed by field-emission scanning electron microscope (FESEM) and energy dispersive X-ray spectroscopy (EDS) attached to FESEM. The results show that water contact angles decrease as discharge energy increases, micro-discharge etching zones are formed into glass surface and different from the control glass in surface micro-structure and chemical compositions.     

介质阻挡放电中的能量转换过程研究

研究了介质阻挡放电过程中的电流强度、电场强度以及电荷分布的演变规律，并对能量转换性质进行了分析.研究结果表明，在一个放电脉冲过程中，外加驱动电源所作的功、电场能量的增量均与起始时刻的壁电荷密度有关，而气体中放电电流所作的功即沉积于气体中的能量与起始时刻的壁电荷密度、放电电流的具体波形无关. 关键词： 介质阻挡放电 壁电荷 动力学过程 能量转换     

�����赲�ŵ�������������ͷ�Ӧ���о�

分别采用空气、氩气大气压介质阻挡放电(DBD)等离子体对重油进行了处理.对经空气DBD等离子体处理后的重油进行粘温特性分析,发现重油粘度升高,流动性变差.红外光谱和四组分分析结果表明重油的重质组分含量升高,重油胶体体系被破坏,同时生成大量刺激性气味气体.为了便于分析气态产物的成分和含量,采用大气压氩气DBD等离子体处理重油并收集气体产物.气相色谱分析发现生成气中含有大量C1-C5的烃类和一定量氢气,其中氢气和甲烷含量占生成气的70％以上.实验结果表明重油在等离子体作用下既发生裂解又发生聚合反应,既生成低碳烃类,本身的流动性也变差.     

Highly concentrated toluene decomposition on the dielectric barrier discharge (DBD) plasma-photocatalytic hybrid system with Mn-Ti-incorporated mesoporous silicate photocatalyst (Mn-Ti-MPS)

This study investigates the Mn-Ti-incorporated mesoporous silicate (Mn-Ti-MPS) as a photocatalyst for highly concentrated toluene removal in a plasma-photocatalytic hybrid system. Various Mn-Ti-MPS [Ti/Si molar ratio = 1/4, Mn/Ti molar ratio = 0.01/1 (1 mol%), 0.05/1 (5 mol%) and 0.1/1 (10 mol%)] photocatalysts were successfully synthesized using a common hydrothermal method without causing any structural damage. In the X-ray diffraction (XRD) pattern, the main peaks of the TiO₂ anatase structure and MnO did not show. All samples displayed hexagonal specific peaks at 2.5° (d_1 0 0 plane), 4.1° (d_1 1 0 plane) and 4.7° (d_2 0 0 plane). This indicates that the Ti ions and Mn ions were well substituted into the Si ion sites in the framework of MCM-41. Their surface areas decreased compared with that of pure MCM-41, while the hexagonal straight pore size was distributed in a range of 2.5-3.5 nm. In the Mn-Ti-MPS, much more water and toluene molecules were absorbed compared to the Ti-MPS. From the X-ray photoelectron spectroscopy (XPS) result, it was determined that the hydrophilicity of the Mn-Ti-MPS was stronger than that of the Ti-MPS. Photocatalytic decomposition for highly concentrated toluene of 1000 ppm increased in the Mn-Ti-MPS when compared with the Ti-MPS, while toluene decomposition on 5 mol% Mn-Ti-MPS was remarkably enhanced to 80% in the plasma system. The conversion to CO₂, however, did not improve in the case of the plasma-only system. Nonetheless, in the plasma-photocatalytic hybrid system, the conversion to CO₂ for 5 mol% Mn-Ti-MPS reached 43% (in an 800 ppm toluene conversion).     

Statistical analysis of the effect of dielectric barrier discharge (DBD) operating parameters on the surface processing of poly(methylmethacrylate) film

A dielectric barrier discharge (DBD) plasma, operating in air at atmospheric pressure, has been used to induce changes in the surface properties of poly(methylmethacrylate) (PMMA) films. The relative effects that key DBD operating parameters, specifically: discharge power, electrode gap and duration of exposure have on producing chemical and microstructural changes in the polymer surface region have been investigated. The approach taken involves the application of an orthogonal array experimental design and statistical analysis methodology. The various data sets obtained from these analyses have been used to develop an equation in which induced changes in the surface properties of the DBD modified PMMA films are expressed in terms of the effectiveness of the various processing parameters in producing them.In general, the results obtained clearly indicate that DBD plasma processing is an effective method for the controlled surface modification of PMMA. Relatively short exposures to the atmospheric pressure discharge produces a significant amount of oxygen incorporation at the surface as indicted by a pronounced reduction in water contact angle. Analysis of the role of each of the operating parameters concerned shows that they do indeed have selective effectiveness for inducing resultant surface modification. Duration of exposure to the DBD plasma, expressed here as the number of treatment cycles at a given speed of specimen transit through the electrode gap, was found to play a major role in decreasing the surface wettability of PMMA. Conversely, the magnitude of the discharge power was not a significant parameter in this regard. In contrast, the value of the applied power played the dominant role in achieving the observed enrichment of the surface oxygen abundance, as measured by XPS, with the duration of exposure to the discharge playing a secondary role in this case.The nature and scale of the induced surface changes that originate from the various processing conditions employed have been further considered to determine if an interrelationship exists between them. Non-parametric data analysis indicates that no significant correlation exists between the observed changes in measured polymer wettability and the attendant surface oxygen enrichment. This result suggests that the increase in surface wettability caused by DBD processing, as manifested in a reduced contact angle, is not merely attributable to changes in the surface chemistry. As such, it is postulated that changes in the surface microstructure may also contribute to this change in surface wettability.     

Experimental research of diffuse bi-directional pulsed dielectric barrier discharge plasma

A bi-directional nanosecond pulsed power supply is employed to generate diffuse dielectric barrier discharge in N₂ using needle-plate electrode configuration at atmospheric pressure. Both discharge images and optical emission spectra of diffuse bi-directional nanosecond high-voltage pulsed dielectric barrier discharge are successfully recorded under severe electromagnetic interference. The diffuse performance of the discharge at different electrode gap distances is observed. The effects of pulse peak voltage, pulse repetition rate, electrode gap distance, He addition, and O₂ addition on the optical emission spectra are investigated. The main physicochemical processes involved are discussed.     

电荷电压法测量DBD等离子体的放电参量

在DBD应用研究中，使用电荷电压法能够测量许多重要参量，如放电功率、放电间隙等效电容、电介质层等效电容、着火电压、放电间隙等效电压及放电间隙电场强度等．同时根据电荷电压图形随工作条件及状态变化的情况还可以诊断DBD等离子体的工作稳定性．文章对相关原理、模拟实验结果及实际应用效果进行了介绍．     

Compared ionic wind measurements on multi-tip corona and DBD plasma actuators

Two sets of actuators with triangular tips on their active electrodes (13 corona and 15 DBD) are studied in the laboratory. Far field ionic wind velocity, mass flow and efficiency are measured for all the actuators. The best electrode shape as function of tip sharpness and tips number/unit length is determined for each of the above measurements. The gas velocity increases downstream of the tips in all the actuators, but the DBD flow has a three-dimensional structure more complicated than for coronas. The tips improve the efficiency of all the actuators, and the stability of coronas is remarkably improved.     

Properties of surface dielectric barrier discharge plasma generator for fabrication of nanomaterials

This paper presents surface dielectric barrier discharge plasma generators as an efficient source of low-energy ions. Either positive or negative ions can be extracted from a plasma cloud with an external DC field created by the third electrode. Three different cross-section geometries of DBD generators were analyzed, simulated and fabricated. Currents of ions extracted from the plasma cloud were measured and the results were discussed. It was demonstrated that if the third electrode consists of liquid–gas interface, the presented arrangement can be used as a versatile reactor for nanomaterial synthesis (on the example of the synthesis of silver nanoparticles).     

UAV flight test of plasma slats and ailerons with microsecond dielectric barrier discharge

Plasma flow control(PFC) is a promising active flow control method with its unique advantages including the absence of moving components, fast response, easy implementation, and stable operation. The effectiveness of plasma flow control by microsecond dielectric barrier discharge(μs-DBD), and by nanosecond dielectric barrier discharge(NS-DBD) are compared through the wind tunnel tests, showing a similar performance between μs-DBD and NS-DBD. Furthermore, theμs-DBD is implemented on an unmanned aerial vehicle(UAV), which is a scaled model of a newly developed amphibious plane. The wingspan of the model is 2.87 m, and the airspeed is no less than 30 m/s. The flight data, static pressure data,and Tufts images are recorded and analyzed in detail. Results of the flight test show that the μs-DBD works well on board without affecting the normal operation of the UAV model. When the actuators are turned on, the stall angle and maximum lift coefficient can be improved by 1.3° and 10.4%, and the static pressure at the leading edge of the wing can be reduced effectively in a proper range of angle of attack, which shows the ability of μs-DBD to act as plasma slats. The rolling moment produced by left-side μs-DBD actuation is greater than that produced by the maximum deflection of ailerons,which indicates the potential of μs-DBD to act as plasma ailerons. The results verify the feasibility and efficacy of μs-DBD plasma flow control in a real flight and lay the foundation for the full-sized airplane application.     

Spontaneous transition of one-dimensional plasma photonic crystal's orientation in dielectric barrier discharge

A novel one-dimensional plasma photonic crystal whose crystal orientation can change spontaneously is demonstrated by using a dielectric barrier discharge with two liquid electrodes. The orientation of the plasma photonic crystal will vary from transverse to longitudinal or vary from longitudinal to transverse and then revert to longitudinal by self-adjustment, while the experimental conditions are kept fixed. The dispersion relations of these plasma photonic crystals are calculated, and the changes of photonic band diagrams during the orientation transition are studied.     

Generation of uniform atmospheric pressure argon glow plasma by dielectric barrier discharge

In this paper, atmospheric pressure glow discharges (APGD) in argon generated in parallel plate dielectric barrier discharge system is investigated by means of electrical and optical measurements. Using a high voltage (0–20 kV) power supply operating at 10–30 kHz, homogeneous and steady APGD has been observed between the electrodes with gap spacing from 0.5 mm to 2 mm and with a dielectric barrier of thickness 2 mm while argon gas is fed at a controlled flow rate of 1 l/min. The electron temperature and electron density of the plasma are determined by means of optical emission spectroscopy. Our results show that the electron density of the discharge obtained is of the order of 10¹⁶ cm^???3 while the electron temperature is estimated to be 0.65 eV. The important result is that electron density determined from the line intensity ratio method and stark broadening method are in very good agreement. The Lissajous figure is used to estimate the energy deposited to the glow discharge. It is found that the energy deposited to the discharge is in the range of 20 to 25 μJ with a discharge voltage of 1.85 kV. The energy deposited to the discharge is observed to be higher at smaller gas spacing. The glow discharge plasma is tested to be effective in reducing the hydrophobicity of polyethylene film significantly.     

常压窄间隙介质阻挡放电等离子体辐射特性

利用带有透明电极与可测向观察的一个介质阻挡放电(DBD)实验装置对它的常压窄间隙等离子体辐射特性进行了实验研究。结果表明：这一DBD装置的辐射特性会受激励电压、激励频率、DBD结构等多种因素影响。在频率为10～20kHz高压电源激励下,采用窄间隙、薄电介质层结构DBD可以大幅度提高放电空间的电场强度,增加放电功率密度,提高了放电装置性能。     

Effect of atmospheric pressure dielectric barrier discharge air plasma on electrode surface

In order to study the influence of plasma on electrode, atmospheric pressure dielectric barrier discharge (DBD) air plasma is employed here to treat copper electrode surface. Plasma is generated between the parallel plate electrodes by means of high voltage produced by a high-frequency power supply with transformer. Electrode surface alterations induced by air plasma are investigated by using field emission scanning electron microscope (FE-SEM), X-ray energy dispersion spectroscopy (EDS) and contact angle measurement. The results show that DBD air plasma removes the organic contaminant on surface and causes electrode surface roughness, oxidization and nitridation. In addition, surface wettability is also improved, as concluded from contact angle measurements.     

�����赲�ŵ���µ����������������о�

进行了介质阻挡放电低温等离子体脱除伴有SO2的烟气中NO的研究,分别进行了直接等离子体脱硫脱硝和间接等离子体脱硫脱硝实验.在直接等离子体脱硫脱硝中,模拟烟气等混合气直接通入等离子体发生器,在反应器中电离分解NO以及和生成的高能电子、离子和自由基等离子体相互反应而进行脱除NO;间接等离子体脱硫脱硝中,模拟烟气连接在等离子体发生器出口与从反应器中产生出的等离子体发生氧化反应而进行脱除NO.结果表明,无论直接形式还是间接形式,脱硝效率都要比脱硫效率高,间接脱硫脱硝能够大大降低功率输入,节省能耗,具有重要的实际应用价值和意义.氨气的加入,有利于脱除效率的提升.