Positive frictional pressure gradient in vertical gas-high viscosity oil slug flow

The present study describes the wall shear stress and the falling liquid film behavior in upward vertical slug flow of air and high viscosity oil. The frictional pressure gradient is directly related to the wall shear stress, and it is usually negative (opposite to the overall flow direction). However, in vertical slug flow, the average total wall shear stress of a slug unit may be negative (in the same direction of the overall flow), resulting in a positive frictional pressure gradient. However, this does not mean, by any way, generation of additional energy or violation of the second law of thermodynamics.The positive frictional pressure gradient phenomenon, reasons and required conditions were explained in this paper. A simplified model was developed and validated against recent experimental data of air-high viscosity oil slug flow in a 50.8 mm ID vertical pipe. The oil viscosity was in the range of 127 mPa s to 580 mPa s. Positive frictional pressure gradient appears when the liquid film wall shear stress supersede the wall shear stress in the slug body. The rate of increase of both wall shear stresses (with respect to the mixture Reynolds number) depend, not only, on the mixture Reynolds number but also, highly, on the liquid viscosity.     

Electroviscous effect on non-Newtonian fluid flow in microchannels

Understanding non-Newtonian flow in microchannels is of both fundamental and practical significance for various microfluidic devices. A numerical study of non-Newtonian flow in microchannels combined with electroviscous effect has been conducted. The electric potential in the electroviscous force term is calculated by solving a lattice Boltzmann equation. And another lattice Boltzmann equation without derivations of the velocity when calculating the shear is employed to obtain flow field. The simulation of commonly used power-law non-Newtonian flow shows that the electroviscous effect on the flow depends significantly on the fluid rheological behavior. For the shear thinning fluid of the power-law exponent n < 1, the fluid viscosity near the wall is smaller and the electroviscous effect plays a more important role. And its effect on the flow increases as the ratio of the Debye length to the channel height increases and the exponent n decreases. While the shear thickening fluid of n > 1 is less affected by the electroviscous force, it can be neglected in practical applications.     

Experimental investigation on thermal properties of silver nanofluids

This paper reports on an experimental investigation of the thermal properties behavior of 0.5 wt% silver nanoparticle-based nanofluids (NF) containing oleic acid (OA) and potassium oleate surfactant (OAK⁺) with concentrations of 0.5, 1, and 1.5 wt% respectively. The experiments were conducted from 20 °C to 80 °C. It was shown that the NF with 1 wt% OAK⁺ yielded the highest thermal behavior enhancement of about 28% at 80 °C compared to deionized water. The thermal performance had higher than the base fluid/nanofluids at approximately 80%. Moreover, the NF containing OAK⁺ showed higher thermal conductivity and dynamics of specific heat capacity than deionized water in all of the experimental conditions in this study. The rheological experiment showed that viscosity of NF was significantly dependant on temperature. As shear rate increased, the shear stress of the NF increased; however, the viscosity of the nanofluids decreased first and then stabilized. It was further found that NF containing OAK⁺ at a range of operating temperatures produced Newtonian behavior.     

Venturi-type fluidic sampler for liquid–solid mixtures

Static-type samplers are required for sampling corrosive, toxic, high-temperature, or radioactive liquid–solid fluids. We have designed a compact reverse flow diverter pumping system for transferring liquid–solid mixtures. In accordance with the Venturi principle, an acceptable volume of liquid–solid fluid is automatically collected into a sampling bottle. The effects of sampling needle sizes, sectional area of the T-section, solid concentration, and liquid viscosity on the performance of fluidic samplers were experimentally investigated. The sample volume increased upon the reduction of the sampling needle length and the increase of the sectional area of the T-section, but decreased with the increase of solid concentration and liquid viscosity. Unbiased samples of acceptable volume were produced by the proposed fluidic sampler, even at 10.21 mPa s liquid viscosity, 35 wt% solid concentration, and 6.74 m sampling height.     

Flow patterns and pressure drop of ionic liquid–water two-phase flows in microchannels

The two-phase flow of a hydrophobic ionic liquid and water was studied in capillaries made of three different materials (two types of Teflon, FEP and Tefzel, and glass) with sizes between 200 μm and 270 μm. The ionic liquid was 1-butyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}amide, with density and viscosity of 1420 kg m⁻³ and 0.041 kg m⁻¹ s⁻¹, respectively. Flow patterns and pressure drop were measured for two inlet configurations (T- and Y-junction), for total flow rates of 0.065–214.9 cm³ h⁻¹ and ionic liquid volume fractions from 0.05 to 0.8. The continuous phase in the glass capillary depended on the fluid that initially filled the channel. When water was introduced first, it became the continuous phase with the ionic liquid forming plugs or a mixture of plugs and drops within it. In the Teflon microchannels, the order that fluids were introduced did not affect the results and the ionic liquid was always the continuous phase. The main patterns observed were annular, plug, and drop flow. Pressure drop in the Teflon microchannels at a constant ionic liquid flow rate, was found to increase as the ionic liquid volume fraction decreased, and was always higher than the single phase ionic liquid value at the same flow rate as in the two-phase mixture. However, in the glass microchannel during plug flow with water as the continuous phase, pressure drop for a constant ionic liquid flow rate was always lower than the single phase ionic liquid value. A modified plug flow pressure drop model using a correlation for film thickness derived for the current fluids pair showed very good agreement with the experimental data.     

Turbulent channel flow of dilute polymeric solutions: Drag reduction scaling and an eddy viscosity model

Direct numerical simulation of viscoelastic turbulent channel flows up to the maximum drag reduction (MDR) limit has been performed. The simulation results in turn have been used to develop relationships between the flow and fluid rheological parameters, i.e. maximum chain extensibility, Reynolds number, Re_τ, and Weissenberg number, We_τ and percent drag reduction (%DR) as well as the slope increment of the mean velocity profile. Moreover, based on the trends observed in the mean velocity profile and the overall momentum balance three different regimes of drag reduction (DR), namely, low drag reduction (LDR; 0 ≤ %DR ≤ 20), high drag reduction (HDR; 20 ≤ %DR ≤ 52) and MDR (52 ≤ %DR ≤ 74) have been identified and mathematical expressions for the eddy viscosity in these regimes are presented. It is found that both in LDR and HDR regimes the eddy viscosity varies with the distance from the channel wall. However, in the MDR regime the ratio of the eddy viscosity to the Newtonian one tends to a very small value around 0.1 within the channel. Based on these expressions a procedure that relies on the DNS predictions of the budgets of momentum and viscoelastic shear stress is developed for evaluating the mean velocity profile.     

Non-Newtonian flow in microporous structures under the electroviscous effect

Single phase non-Newtonian microporous flow combined with the electroviscous effect is investigated in the pore-scale under conditions of various rheological properties and electrokinetic parameters. The lattice Boltzmann method is employed to solve both the electric potential field and flow velocity field. The simulation of commonly used power-law non-Newtonian flow shows that the electroviscous effect on the flow depends on both the fluid rheological behavior and pore surface area ratio significantly. For the shear thinning fluid with power-law exponent n < 1, the fluid viscosity near the wall is smaller and the electrovicous effect plays a more important role compared to the Newtonian fluid and shear thickening fluid. The high pore surface area ratio in the porous structure increases the electroviscous force and the induced flow resistance becomes important even to the flow of Newtonian and shear thickening fluids.     

Atomization of glycerin with a twin-fluid swirl nozzle

Atomization of liquids with high viscosity is always a challenge, especially when small diameter droplets and high liquid flow rates are simultaneously required. In the present research, the performance of a Venturi–vortex twin-fluid swirl nozzle is examined, attending to its capabilities to generate droplets with diameters below 20 µm when atomizing pure glycerin at room temperature. In this nozzle, air is injected tangentially in a central convergent section, and discharges suctioning the liquid fed to a coaxial chamber, here using a gear pump. The resulting spray is visualized and analyzed. Droplet size distributions are measured with a laser diffractometer. As expected, droplet diameter increases with liquid flow rate, and quickly diminishes when air flow rate is increased. Sauter mean diameters (SMD) below 15 µm can be obtained even when atomizing pure glycerin. However, these values are obtained for relatively low glycerin flow rates (∼5 l/h), and with rather wide distributions. For 10 l/h and an air-to-liquid mass flow rate ratio (ALR) of 13.7 more than 26% of the glycerin volume is atomized in droplets smaller than 20 µm. Liquid ligaments are observed near the nozzle exit, but they tend to break up while moving downstream.     

Local flow structure beyond bubbly flow in large diameter channels

A thorough review of the available literature has revealed a significant lack of usable data regarding the transport of interfacial area in large diameter channels. This represents a concern for various industrial systems, but especially for predicting the performance of safety systems in nuclear reactor systems. In order to remedy this gap in the current experimental database a series of experiments has been performed. These experiments included the measurement of the local interfacial area concentration and other parameters using local electrical conductivity probes in pipes with diameters of 0.152 m [6 in.], 0.203 m [8 in.] and 0.304 m [12 in.]. Volumetric fluxes ranged up to 2 m/s [6.56 ft/s] for the liquid phase and 10 m/s [32.8 ft/s] for the gas phase, and two nominal pressure conditions of 180 kPa [26.1 psia] and 280 kPa [40.6 psia] were included. Gas was injected as large cap bubbles in order to provide a basis for evaluating models for cap-bubbly flow at low void fractions. Measurements were performed simultaneously at three axial locations to allow the evaluation of interfacial area transport. The resulting data provides valuable insight into the flow structure and behavior in all flow regimes other than annular flow and will serve as a valuable database for the evaluation of models for predicting the transport of interfacial area across a wide variety of flow conditions and pipe sizes.     

The atomization of water–oil emulsions

The paper presents the results of experimental studies on atomization of the emulsions flowing through twin-fluid atomizers obtained by the use of the digital microphotography method. The main elements of the test installation were: nozzle, reservoir, pump and measurement units of liquid flow. The photographs were taken by a digital camera with automatic flash at exposure time of 1/8000 s and subsequently analyzed using Image Pro-Plus. The oils used were mineral oils 20–90, 20–70, 20–50 and 20–30. The studies were performed at flow rates of liquid phase changed from 0.0014 to 0.011 (dm³/s) and gas phase changed from 0.28 to 1.4 (dm³/s), respectively. The analysis of photos shows that the droplets being formed during the liquid atomization have very different sizes. The smallest droplets have diameters of the order of 10 μm. The experimental results showed that the changes in physical properties of a liquid phase lead to the significant changes in the spray characteristics. The analysis of the photos of water and emulsions atomization process showed that the droplet sizes are dependent on gas and liquid flow rates, construction of nozzle and properties of liquid. The differences between characteristics of atomization for water and emulsions have been observed. Analysis of photos on forming the droplets in air–water and air-emulsions systems showed that droplets are bigger in air-emulsion system (at the same value of gas to liquid mass ratio). The values of Sauter mean diameter (SMD) increased with increase of volume fraction of oil in emulsion. The droplet size increased with emulsion viscosity.     

An experimental and numerical study of the localization behavior of tantalum and stainless steel

In general, the shear localization process involves initiation and growth. Initiation is expected to be a stochastic process in material space where anisotropy in the elastic–plastic behavior of single crystals and inter-crystalline interactions serve to form natural perturbations to the material’s local stability. A hat-shaped sample geometry was used to study shear localization growth. It is an axi-symmetric sample with an upper “hat” portion and a lower “brim” portion with the shear zone located between the hat and brim. The shear zone length is 870–890 μm with deformation imposed through a split-Hopkinson pressure bar system at maximum top-to-bottom velocity in the range of 8–25 m/s. We present experimental results of the deformation response of tantalum and 316L stainless steel samples. The tantalum samples did not form shear bands but the stainless steel sample formed a late stage shear band. We have also modeled these experiments using both conductive and adiabatic continuum models. An anisotropic elasto-viscoplastic constitutive model with damage evolution was used within the finite element code EPIC. A Mie-Gruneisen equation of state and the rate and temperature sensitive MTS flow stress model together with a Gurson flow surface were employed. The models performed well in predicting the experimental data. The numerical results for tantalum suggested a maximum equivalent strain rate on the order of 7 × 10⁴ s⁻¹ in the gage section for an imposed top surface displacement rate of 17.5 m/s. The models also suggested that for an initial temperature of 298 K a temperature in the neighborhood of 900 K was reached within the shear section. The numerical results for stainless steel suggest that melting temperature was reached throughout the shear band shortly after peak load. Due to sample geometry, the stress state in the shear zone was not pure shear; a significant normal stress relative to the shear zone basis line was developed.     

Flow of dilute to semi-dilute polystyrene solutions through a benchmark 8:1 planar abrupt micro-contraction

We have studied the flow of thermodynamically ideal solutions of a high molecular weight (M_w = 6.9 MDa) atactic polystyrene in the θ solvent dioctyl phthalate (aPS in DOP) through a micro-fabricated 8:1 planar abrupt contraction geometry. The channel is much deeper than most micro-scale geometries, providing an aspect ratio of 16:1 and a good approximation to 2D flow in the narrow channel. The solutions span a range of concentration 0.03 wt.% < c < 0.6 wt.%, encompassing the dilute to semi-dilute regimes and providing a range of fluid viscosities and relaxation times such that we achieve a range of Weissenberg numbers (8.7 < Wi < 1562) and Reynolds numbers (0.07 < Re < 11.2), giving elasticity numbers between 31 < El < 295. We study the flow using a combination of micro-particle image velocimetry (μ-PIV) to characterize the flow field, pressure measurements to evaluate the non-Newtonian viscosity, and birefringence measurements to assess macromolecular strain. Flow field observations reveal three broad flow regimes characterized by Newtonian-like flow, unstable flow and vortex growth in the upstream salient corners. Transitions between the flow regimes scale with Wi, independent of El, indicating the dominance of elastic over inertial effects in all the fluids. Transitions in the flow field are also reflected by transitions in the relative viscosity (determined from the pressure drop) and the macromolecular strain (determined from birefringence measurements). The strain through the 8:1 contraction saturates at a value of ～4–5 at high Wi. The results of these experiments broaden the limited set of literature on flow through micro-fluidic planar contractions and should be of significant value for optimizing lab-on-a-chip design and for comparison with modeling studies with elasticity dominated fluids.     

Numerical simulation of the fountain flow instability in injection molding

For the first time, the viscoelastic flow front instability is studied in the full non-linear regime by numerical simulation. A two-component viscoelastic numerical model is developed which can predict fountain flow behavior in a two-dimensional cavity. The eXtended Pom-Pom (XPP) viscoelastic model is used. The levelset method is used for modeling the two-component flow of polymer and gas. The difficulties arising from the three-phase contact point modeling are addressed, and solved by treating the wall as an interface and the gas as a compressible fluid with a low viscosity. The resulting set of equations is solved in a decoupled way using a finite element formulation. Since the model for the polymer does not contain a solvent viscosity, the time discretized evolution equation for the conformation tensor is substituted into the momentum balance in order to obtain a Stokes like equation for computing the velocity and pressure at the new time level. Weissenberg numbers range from 0.1 to 10. The simulations reveal a symmetric fountain flow for Wi = 0.1–5. For Wi = 10 however, an oscillating motion of the fountain flow is found with a spatial period of three times the channel height, which corresponds to experimental observations.     

3D particle image velocimetry of the flow field around a sphere sedimenting near a wall: Part 1. Effects of Weissenberg number

The flow fields surrounding a sphere sedimenting through a liquid near a vertical wall are characterized using 3D stereoscopic particle-image velocimetry (PIV) experiments. Three different fluids, a Newtonian reference fluid, a constant (shear) viscosity Boger fluid, and a shear-thinning elastic fluid, are used to determine the effects of both elasticity and shear-thinning on the flow field. All three fluids have similar zero shear viscosities. The Weissenberg number is manipulated by varying the diameter and the composition of the ball. Significant differences are found for the different types of fluid, demonstrating both the influence of elasticity and shear-thinning on the velocity fields. In addition, the impact of the wall on the flow field is qualitatively different for each fluid. We find that the flow behind the sphere is strongly dependent on the fluid properties as well as the elasticity. Also, the presence of a negative wake is found for the shear-thinning fluid at high Weissenberg number (Wi > 1).     

Comparison of a quasi-Newtonian fluid with a viscoelastic fluid in planar contraction flow

The flow of a 5.0 wt.% solution of polyisobutylene in tetradecane through a planar 4 : 1 contraction exhibiting a shear thinning viscosity is simulated using the flow-type sensitive quasi-Newtonian fluid model. The shear viscosity is fitted by the Giesekus model, which, with the chosen parameters, leads to an extension thickening elongational viscosity. The stress and velocity fields of the numerical simulations are compared with the experimental results of Quinzani et al. [J. Non-Newtonian Fluid Mech. 52 (1994) 1–36] and the numerical results of the viscoelastic simulation using the Giesekus model of Azaiez et al. [J. Non-Newtonian Fluid Mech. 62 (1996) 253–277]. It can be shown that the quasi-Newtonian fluid qualitatively predicts the essential features of the flow in the vicinity of the contraction.     

Smoothed particle hydrodynamics simulation of non-Newtonian moulding flow

Smoothed particle hydrodynamics (SPH) has been widely applied in simulating fluid flow because of its attractive properties, for example, it is fully Lagrangian and mesh free. However, this method usually uses the explicit method to solve the conservation equations and in this form it is only suitable to momentum dominated flows with low viscosity. In polymer processing, the fluid is non-Newtonian with high viscosity, O(10³) to O(10⁴) Pa-s say, and the pressure is high as O(10⁶) to O(10¹⁰) Pa. The algorithm of the standard SPH is infeasible in this case, because only very small time steps can be used for a stable simulation. We have developed an implicit SPH for non-Newtonian flow, which is completely matrix free, to solve the equation system iteratively and robustly. The artificial pressure is introduced between particles to stabilize the SPH system avoiding the tensile instability. The fluid is compressible under high pressure. Realistic state equations for polymers, such as the Tait and SSY [16] equations are adopted to describe the density/pressure relations. The method is finally applied to the simulation of moulding flow of a modified power law fluid with the zero shear rate viscosity of 1.22 × 10⁴ Pa-s, Reynolds number of 3 × 10^?4 to 6 × 10^?5 and the highest pressure of O(10⁸) to O(10¹⁰) Pa.     

Flow pattern and molecular visualization of DNA solutions through a 4:1 planar micro-contraction

The present work explores unusual flow behavior of entangled fluids in an abrupt contraction flow device. Fluorescent imaging was carried out on four different entangled DNA solutions with concentrations ranging from 0.1 to 1.0% (with a wide range of entanglements per chain Z = 7–55). For weakly entangled solutions (Z < 30), vortex flow was dominant at high flow rates. However, for well-entangled DNA solutions (Z ≥ 30), unusual time dependant shear banding was observed at the contraction entrance. Upon reducing the slip length by adding sucrose to the well-entangled DNA solution, vortex flow became dominant again. In vortex flow, most DNA chains remained coiled at the corner in regular recirculation. However, when jerky-shear-banding flow developed, significant stable stretching of DNA chains occurred at the center-line, with quasi-periodic switching between stretching and recoil at the corner.     

Two-phase flow behavior inside a header connected to multiple parallel channels

The main objective of this work is to examine the flow distribution of two-phase mixture to parallel channels and to investigate the flow behavior at header-channel junctions simulating the corresponding parts of compact heat exchangers. The cross-section of the header and the channels were fixed to 14 mm × 14 mm and 12 mm × 1.6 mm, respectively. The mass flux and the mass quality ranges were 70–165 kg/m² s and 0.3–0.7, respectively. Air and water were used as the test fluids. The flow distribution at the fore part of the header (region A) is affected only by the upstream flow configuration and the rate of liquid flow separation decreased a flowing downwards. On the other hand, in the rear part, the downstream effect predominates over the upstream effect due to strong flow recirculation near the end plate. In this part, the liquid separation increased (region B) and then decreased (region C) as the mixture proceeds downwards. The validity of the existing models for branching flows at parallel T-junction was tested, and turned out to be appropriate for region A. However, the models were not applicable to the rear part due to a strong flow recirculation. Moreover, the effect of the membranes in channels was investigated, but that was minor.     

Drag reduction for liquid flow through micro-apertures

Pressure drops in the flow through micro-orifices and capillaries were measured for silicone oils, aqueous solutions of polyethylene glycol (PEG), and surfactant aqueous solutions. The diameter of micro-orifices ranged from 5 μm to 400 μm. The corresponding length/diameter ratio was from 4 to 0.05 and capillary diameters were 105 μm and 450 μm. The following results were obtained: silicone oils of 10^?6 m²/s and 10^?5 m²/s in kinematic viscosity generated a reduction of pressure drop (RPD), that is, drag reduction, similar to the RPD of water and a glycerol/water mixture reported in the previous paper by the present authors. When RPD occurred, the pressure drop (PD) of silicone oils of 10^?6 m²/s and 10^?5 m²/s had nearly the same magnitude. Namely, the difference in viscosity did not influence RPD. A 10³ ppm aqueous solution of PEG20000 provided almost the same PD as that of PEG8000 for the 400 μm to 15 μm orifices, but a greater PD than that of PEG8000 for the 10 μm to 5 μm orifices. A non-ionic surfactant and a cationic surfactant were highly effective in RPD compared with anionic surfactants: the non-ionic and cationic surfactant solutions had PD one order of magnitude lower than that of water under some flow conditions in the concentration range from 1 ppm to 10⁴ ppm, but the anionic surfactant solutions did not generate RPD except in the case of the smallest orifice of 5 μm in diameter. The PD of the non-ionic surfactant solution showed a steep rise at a Reynolds number (Re_t) for 400 μm to 15 μm orifices. The Re_t provides the relationship Re_t = K/D, where D is the orifice diameter, and K is a constant of 2 × 10^?2 m for the 100–20 μm orifices irrespective of liquid concentration. Capillary flow experiment revealed that the PEG, non-ionic and cationic surfactant solutions generated RPD also in a laminar flow through the capillary of 105 μm in diameter, but not in the flow through the capillary of 450 μm in diameter. In order to clarify the cause of RPD, an additional experiment was carried out by changing the orifice material from metal to acrylic resin. The result gave a different appearance of RPD, suggesting that RPD is related to an interfacial phenomenon between the liquid and wall. The large RPDs found in the present experiment are very interesting from both academic and practical viewpoints.     

Influence of sudden contractions on in situ volume fractions for oil–water flows in horizontal pipes

Oil–water two-phase flow experiments were conducted in horizontal ducts made of Plexiglas® to determine the in situ oil fraction (holdup) by means of the closing valves technique, using mineral oil (viscosity: 0.838 Pa s at 20 °C; density: 890 kg m⁻³) and tap water. The ducts present sudden contractions from 50 mm to 40 mm i.d. and from 50 mm to 30 mm i.d., with contraction ratios of 0.64 and 0.36, respectively. About 200–320 tests were performed by varying the flow rates of the phases. Flow patterns were investigated for both the up- and downstream pipe in order to assess whether relevant variations of the flow patterns across the sudden contraction take place. Data were then compared with predictions of a specific correlation for oil–water flow and some correlations for gas–water flow. A drift-flux model was also applied to determine the distribution parameter.