Recent developments in the separation of inorganic and small organic ions by capillary electrophoresis

Which method should I use for ion analysis, ion chromatography (IC) or capillary electrophoresis (CE)? In terms of actual theoretical plates CE has a clear-cut advantage. The separation ability of IC is adequate for many sample types, and many separation scientists feel that IC offers greater reliability and confidence than CE. However, IC is a more mature technique and there has been more time to solve problems such as peak tailing and to improve reproducibility. The two techniques should be viewed as complementary. A number of recent developments in ion analysis by CE are discussed. These include some simple ways to control electroosmotic flow and improve reproducibility, separation of isotopes, improved methods of indirect photometric detection, a new contactless conductivity detector, separation of ions at low pH, and in solutions of high salt content. Progress in a new technique called IC-CE will be described in which a soluble ion-exchange polymer is added to the capillary electrolyte to separate anions based on differences in both electrophoretic mobility and ion-exchange interactions.     

Development of ion chromatography and capillary electrophoresis methods for the determination of Li in Li–Al alloy

Two methods were developed for determination Li content in Li–Al alloy by employing ion chromatography (IC) and capillary electrophoresis (CE) without any prior separation of Al matrix. In absence of suitable certified reference material the two methods were used to validate each other. Using a high capacity column and a weaker eluent methane sulphonic acid, it was possible to separate Li in IC without eluting strongly retained Al. The method showed good precision and sensitivity and was extended for analysis of routine samples. In the case of CE using imidazole as co-ion, Li was detected in CE by indirect detection. In view of no interference from Al, samples were analyzed without any matrix separation. The CE method was used successfully for sample analysis and results were compared with IC results.     

Developments in sample preparation and separation techniques for the determination of inorganic ions by ion chromatography and capillary electrophoresis.

A review is presented of sample preparation and separation techniques for the determination of inorganic ions by ion chromatography (IC) and capillary electrophoresis (CE). Emphasis has been placed on those sample treatment methods which are specific to inorganic analysis, and the developments in separation methods which are discussed are those which enhance the capabilities of IC and CE to handle complex sample matrices. Topics discussed include solid-phase extraction for sample clean-up and preconcentration, dialytic methods, combustion methods, matrix-elimination IC, electrostatic IC, electrically polarised ion-exchange resins, electromigration sample preparation in CE, chromatographic sample preparation for CE, use of high-ionic strength background electrolytes, buffering of background electrolytes in CE, use of capillary electrochromatography for inorganic determinations, and methods for the manipulation of separation selectivity in both IC and CE. Finally, some possible future trends are discussed.     

Identification and determination of inorganic anions in real extracts from pre- and post-blast residues by capillary electrophoresis

Fast, selective, and sensitive analysis of inorganic anions is compulsory for the identification of explosives in post-blast or environmental samples. For the last twenty years, capillary electrophoresis (CE) has become a valuable alternative to ion chromatography (IC) for the analysis of inorganic-based explosives because of its low running costs and its simplicity of use. This article focuses on the development and validation of a CE method for the simultaneous analysis of 10 anions (chloride, nitrite, nitrate, thiosulphate, perchlorate, chlorate, thiocyanate, carbonate, sulphate, and phosphate) which can be found in post-blast residues, plus for the first time azide anion, possibly present in the composition of detonators, and the internal standard (formate) in 20 min total runtime. Intermediate precisions were 2.11% for normalized areas and 0.72% for normalized migration times. Limits of detection close to 0.5 ppm for all anions were obtained with the use of preconcentration techniques, thanks to a fast and simple sample preparation allowing the analysis of a large variety of matrices with the developed generic CE method. The matrix effects were statistically studied for the first time in the explosive field for different matrices, containing interfering anions and cations, sometimes at high levels. In fact, no significant matrix effect occurred (tests with blank matrix extracts of soil, cloth, glass, plastic, paper, cotton, and metal). Finally, analyses of real post-blast residues and real detonator extracts were performed. The CE results were compared with those obtained with the IC method used routinely and showed excellent correlation.     

Integrated circuit microchip system with multiplex capillary electrophoresis module for DNA analysis

In this paper, we describe the use of an integrated circuit (IC) microchip system as a detector in multiplex capillary electrophoresis (CE). This combination of multiplex capillary gel electrophoresis and the IC microchip technology represents a novel approach to DNA analysis on the microchip platform. Separation of DNA ladders using a multiplex CE microsystem of four capillaries was monitored simultaneously using the IC microchip system. The IC microchip-CE system has advantages such as low cost, rapid analysis, compactness, and multiplex capability, and has great potential as an alternative system to conventional capillary array gel electrophoresis systems based on charge-coupled device (CCD) detection.     

Development and validation of analytical methodology using capillary electrophoresis for separation and determination of anions in rainwater

A new capillary electrophoresis (CE) procedure was developed for simultaneous determination of both organic and inorganic anions in rain water using a background electrolyte (BGE) containing 5 mM molybdate, 0.15 mM CTAH, 0.01% PVA and 5 mM Tris buffer to adjust pH at 7.9. Under optimised conditions, good repeatability (RSD for sulphate in migration time=0.36% and peak area=4.2%), low detection limit (2 ppb for chloride) and satisfactory working range (50 ppb-20 ppm for hydrodynamic injection, 10 ppb-3 ppm for electrokinetic injection for chloride) were obtained. The reliability of the CE procedure developed was established by satisfactory recovery tests and good agreement of results obtained by both the CE and ion chromatography (IC) methods. The procedure developed had been successfully applied for field monitoring of rainwater showing good repeatability and capability of detecting trace anions at ppb levels beyond the IC working range. Thus, the new CE procedure developed provides a quick, sensitive, economic and reliable method to meet the need for the simultaneous determination of both organic and inorganic anions in the acid rain monitoring programme.     

Routine determination of major anions in atmospheric aerosols by capillary electrophoresis

Capillary electrophoresis (CE) with indirect UV detection utilizing a pyromellitate-based electrolyte was used for the routine analysis of major anions in atmospheric aerosols collected on filters with high-volume (Hi-Vol) samplers. The long-term reliability of the CE system was checked over an 8-month period during which over 2900 samples were analyzed. In addition, approximately 1100 samples were analyzed in parallel by ion chromatography (IC). It has been shown that acceptable analytical performance can be routinely obtained. The agreement between the CE and IC results is good, generally better than 20% at concentrations larger than 1 mg l⁻¹.     

On-line immobilized acetylcholinesterase microreactor for screening of inhibitors from natural extracts by capillary electrophoresis

In this study we developed a simple capillary electrophoresis (CE) method with an on-line acetylcholinesterase (AChE) microreactor at the inlet of capillary for inhibitor screening. The fused-silica capillary surface was modified with a polycationic polyethylenimine coating. Solutions of the enzyme and chitosan were then injected to immobilize the enzyme in approximately 2.9?cm of the capillary inlet (total length of capillary 60.2?cm) by electrostatic interaction and the film overlay technique. Separation of enzyme reaction product (thiocholine, ThCh) and unreacted substrate (acetylthiocholine, AThCh) was achieved within 3.0?min. The conditions affecting the efficiency of reaction of the enzyme were optimized by measuring the peak area of ThCh. Under the optimum conditions, using Huperzine-A as model inhibitor, K (i) and IC (50) were 0.551?μmol?L(-1) and 1.52?μmol?L(-1), respectively, for immobilized AChE. Finally, screening of a small compound library containing two known AChE inhibitors and 30 natural extracts was conducted, and species with inhibition activity were directly identified. Compared with previous publications on screening for AChE inhibitors in natural products based on CE methods, the method developed in this work has the advantages of lower cost per analysis, less leakage, and better bioaffinity for the immobilized enzyme because of the unique properties of sodium alginate and chitosan.     

Fast chromatographic separation techniques as competitors to chemical and biochemical sensor systems

Fast chromatographic methods, e.g. chromatography with supercritical fluids, ion chromatography and especially capillary electrophoresis, are important competitors of chemical sensors in environmental monitoring and process control. These methods show high selectivity and low interferences and it is possible to determine several parameters within a single chromatographic run. In order to show the potential and limitation of sensor systems and chromatographic separation methods in environmental analysis this review is limited to applications in this field.With regard to practical problems a comparison of ion chromatography (IC), capillary electrophoresis (CE) and electrochemical sensors is given for a special example, the ion analysis in waste water. Authentic water samples with a high surfactant content from a car-wash are examined, proving the suitability of IC, CE and electrochemical sensors in terms of specifity, sensitivity, reproducibility, analysis time and calibration linearity. The results show that the chromatographic methods are useful techniques in water analysis, yielding good sensitivity, high resolution and short analysis times. In comparison the chemical sensor also shows short analysis times, good sensitivity and a simple instrumental set-up. The disadvantage is the lack of selectivity and the instability of the sensor signal, when the sensor is exposed to the extremely complex matrix. Good results could only be achieved by pretreatment of the sample solution.     

The importance of capillary electrophoresis,capillary electrochromatography,and ion chromatography in separations of inorganic ions

The importance of capillary electrophoresis (CE), capillary electrochromatography (CEC), and ion chromatography (IC) in inorganic ion analyses is outlined. Methods for improving the reliability of the CE measurements are briefly described. Selectivity optimization in CE analyses of inorganic cations and anions is discussed. Using the Peakmaster program, CE system peaks (system zones, eigenmobilites) and some important CE parameters, such as effective mobilities, electromigration dispersion, indirect UV, and direct conductivity signals, are predicted and compared with experimental analyses.     

Analysis of sample of highly water-soluble Th-symmetric fullerenehexamalonic acid C66(COOH)12 by ion-chromatography and capillary electrophoresis

Ion chromatography (IC) was used to establish isomer purity of the highly water-soluble sample of fullerenehexamalonic acid, Th-symmetric hexakis-adduct C66(COOH)12. Sharp and symmetric peaks were obtained by IC using 1.0 M potassium hydroxide as eluent and applying gradient elution program. The identity of the two largest peaks in the chromatogram was assigned to Th-C66(COOH)12 and C66H(COOH)11. The developed IC procedure can be used for the semi-quantitative determination of the extent of the partial decarboxylation of the sample. As an alternative analytical technique, a CE procedure was introduced and its performance against IC was compared for this particular case.     

Capillary electrophoretic determination of thiosulfate,sulfide and sulfite using in-capillary derivatization with iodine

A new capillary electrophoresis (CE) method was developed for the rapid, simple and selective determination of thiosulfate, sulfide and sulfite species. The proposed method is based on the in-capillary derivatization of separated sulfur anions by mixing their zones with the iodine zone during the electrophoretic migration and direct UV detection of iodide formed. The optimal conditions for the separation and derivatization reaction were established by varying electrolyte pH, electrolyte counter-ion, concentration of iodine, and applied voltage. The optimized separations were carried out in 20 mmol/L Tris-chloride electrolyte (pH 8.5) using direct UV detection at 214 nm. All three sulfur species were well resolved in less than 4 min. The method gives repeatability comparable or even better than this obtained for sulfur anions using standard CE technique. The proposed CE system was applied to the monitoring of sulfur anions in spent fixing solutions during the electrolytic oxidation.     

Development and validation of a capillary electrophoresis method with ultraviolet detection for the determination of the related substances in a pharmaceutical compound

A capillary electrophoresis (CE) method was successfully developed to quantify the impurity profile of a new substance of pharmacological interest: LAS 35917. CE method was developed in order to separate the chloromethylated, monomethylated and hydroxylated impurities (molecules with very similar chemical structures) having the three coelution in the reversed-phase LC method initially established. Taking into account the structure of the impurities of LAS 35917, separation by conventional liquid chromatography (LC) methods would be longer and tedious than separation by CE, which is an appropriate and versatile technique giving easier and quicker methods. Among the three potential impurities mentioned of LAS 35917, two are due to the synthesis route of this drug, and the third arises from degradation. These drug-related impurities were separated using a capillary of 56 cm of effective length and 50 microm I.D., a 60 mM tetraborate buffer, at pH 9.2, and a positive voltage of 20 kV. The optimised CE method was preliminary validated with regard to specificity, linearity, limits of detection and quantitation, repeatability and solution stability. The method allows the detection and quantitation of impurities above 0.04 and 0.08% level, respectively. All three related substances were separated, detected and quantified from their parent drug in the analysis of real samples of LAS 35917, stressed or not stressed, with this simple and fast CE method.     

Evaluation of Liquid Chromatography and Capillary Electrophoresis for the Elucidation of the Artificial Colorants Brilliant Blue and Azorubine in Red Wines

Summary Liquid chromatography (LC) and capillary electrophoresis (CE) have been compared for the analysis of the dyes brilliant blue and azorubine in red wines. A liquid-liquid extraction procedure followed by an ion-pair LC method was developed to separate the dyes from the wine polyphenols allowing reliable UV-spectral identification of the target dyes with limits of detection of 10 and 20 ppb for azorubine and brilliant blue, respectively. Because adulteration of wine with dyes is usually in the ppm level, CE proved to be a good alternative for the LC method. CE could be applied after a simple sample clean-up step by SPE eliminating interference from the bulk of the polyphenols. Although LC proved to be more sensitive compared to CE, the latter is more effective in reducing interferences from other wine components and showed the typical advantages of CE such as low solvent consumption and speed of analysis.     

On-line preconcentration of protein in capillary electrophoresis with an end-column cellulose acetate-based porous membrane

A simple on-line preconcentration method of protein for capillary electrophoresis (CE) using a cellulose acetate (CA)-coated porous membrane was proposed. CA membrane is fabricated at one of the ends of the column that allows the passage of buffer ions but excludes larger protein molecules. Protein sample is continuously electrokinetically loaded and trapped by the membrane. When injection is completed, the direction of the electric field is switched and the trapped proteins are then separated by conventional CE procedure. The results achieved showed that the preconcentration mechanism of this method was based on size-exclusion effect. Bovine serum albumin (BSA) was used for model protein sample, and signal enhancement of 550-fold with 15 min injection time was achieved.     

Recent progress in pharmacokinetic applications of capillary electrophoresis

This review is a continuation of the previous reviews (Electrophoresis 1999, 20, 3259-3268; Electrophoresis 2001, 22, 4244-4248) to update the recent publications from 2001 to 2003 on pharmacokinetic studies using capillary electrophoresis (CE). During this period of time, CE remains as a unique analytical method for some studies, which would otherwise be limited by many factors, such as the sample volume, detection sensitivity, or separation power. It is particularly noticeable that the separation of chiral drugs in biological sample and the use of solid-phase extraction (SPE) as a simple and convenient means of sample preparation appear to become popular for CE-based assays. The use of CE for assessing complete pharmacokinetic information, however, did not show a significant growth during this period of time. In order to provide a broad range of view on how biological samples are analyzed by CE, this review will cover publications during the past two years on the use of CE for the analysis of drugs in biological fluids for general pharmacokinetic applications including drug monitoring and bioavailability studies.     

抗氧化剂的毛细管电泳-间接化学发光联用在线评价方法研究

根据碱性条件下羟自由基与luminol反应会产生化学发光而抗氧化剂能够清除羟自由基从而抑制发光的原理, 结合毛细管电泳技术, 建立了一种针对多组分共存体系中抗氧化组分的在线评价的新方法. 对这种毛细管电泳-间接化学发光检测技术, 优化化学发光的各种条件, 考察了抗氧化剂硫脲和麻黄碱的抗氧化活性, 采用曲线拟合求出它们对羟自由基的半数清除浓度(IC₅₀), 得出抗氧化活性大小为麻黄碱＞硫脲, 这与荧光分光光度法的结果一致. 该方法初步应用于评价中药槐米提取物化学组分的抗氧化活性.     

Separation and Determination of the Active Ingredients in Tablets Composite Triamterene by Capillary Electrophoresis with Amperometric Detection

Hydrochlorothiazide (HCTZ) is one of the diuretics. When it incorporated with triamterene (TATR), better therapeutic effect would be obtained^[1].A simple, rapid method for separation and determination of TATR and HCTZ in composite tablets by capillary electrophoresis (CE) with amperometric detection (AD) was demonstrated in this paper.     

Comparison of HPLC and CE methods for the determination of cetirizine dihydrochloride in human plasma samples

Two methods, capillary electrophoresis (CE) and high-performance liquid chromatography (HPLC), for analysis of cetirizine dihydrochloride in small sample volumes of human plasma were compared. The CE and HPLC assays were developed and validated by analyzing a series of plasma samples containing cetirizine dihydrochloride in different concentrations using these two methods. The extraction procedure is simple and no complicated purification steps or derivatization are required. The analysis time in the HPLC method was shorter than that in the CE method, but solvent consumption was considerably lower in the CE method. The calibration curve was linear to at least 10-1000 ng/mL both for CE and HPLC with r(2) = 0.9993 and r(2) = 0.9994, respectively. The detection limits for cetirizine dihydrochloride were 3 and 5 ng/mL with CE and HPLC (a UV detector was applied in the both cases), respectively. Both methods were selective, robust and specific, allowing reliable quantification of cetirizine dihydrochloride, and could be useful for clinical and biomedical investigations.