Trace element content of medicinal plants from Algeria

Neutron activation analysis (INAA) has been applied to multielemental determination of eleven medicinal plants used to cure the urinary tract diseases observed in Algeria. These plants include Androgena Citratus, Ceratonia Siliquata, Punica Granatum, Glyryrrhiza Glabra, Lausaunia Alba, Fragaria Vesca, Arbutus Unedol, Hordeum Vulgaris, Papieteria Officinalis, Zea Mays L, and Davallia Seae. Concentrations of twenty elements Ba, Br, Ca, Cl, Co, Cu, Cr, Fe, I, Mn, Na, Mg, Rb, Sb, Se, Sc, Sr, Ti, V, and Zn have been determined by short, and long irradiation times with a thermal and epithermal flux of 1.4·10¹² n·cm⁻²·s⁻¹ and 1.4·10¹¹ n·cm⁻²·s⁻¹, respectively. These analyses were performed in conjunction with Compton suppression. In almost herbs studied the Co, Cr, Cu, Rb, Sb, Sc, Se and V are found to be present at trace levels, Br, Mn, and Zn at the minor level, and Ca, Cl, Fe, Mg and Na are generally at the major level. The accuracy of the measurements has been evaluated by analyzing NIST-botanical references materials.     

Investigation of the interaction of Greek dolomitic marble with metal aqueous solutions using rutherford backscattering and X-ray photoelectron spectroscopy

To enhance the applicability of the nuclear analytical technique in the field of industry and the environment, the inorganic elemental content of the bottom ash from a municipal solid waste incinerator was determined by instrumental neutron activation analysis. Bottom ash samples were monthly collected from an incinerator located at a metropolitan city in Korea, strained through a 5 mm sieve, dried by an oven and pulverized by an agate mortar. The samples were irradiated at the NAA #1 irradiation hole (thermal neutron flux: 2.92·10¹³ n·cm⁻²·s⁻¹) in the HANARO research reactor of the Korea Atomic Energy Research Institute and the irradiated samples were measured by a HP Ge gamma-ray spectrometer. Thirty-three elements including As, Cr, Cu, Fe, Mn, Sb and Zn were analyzed by an absolute method. The quality control was conducted by a simultaneous analysis with NIST standard reference materials. The average concentrations of the major elements such as Ca, Fe, Al, Na, Mg, K and Ti measured in the sample were 19.9%, 4.85%, 3.79%, 2.11%, 1.84%, 1.22% and 1.02%, respectively. In addition, the concentrations of the hazardous metals like Zn, Cu, Cr, Sb and As were 0.77%, 0.31%, 729 mg·kg⁻¹, 116 mg·kg⁻¹ and 22.2 mg·kg⁻¹, respectively.     

Study of trace impurities in heroin by neutron activation analysis

Sixty-two heroin samples were analyzed for their contents of 15 trace elements (Au, Ba, Br, Ca, Ce, Co, Cr, Fe, La, Na, Sb, Sc, Sm, Th, and Zn) by neutron activation analysis (NAA). Large variations of elemental concentrations between samples were found to possess statistical significance. Of all the elements calcium was the most abundant element, followed by zinc and sodium. The concentrations of Au, Ce, Co, La, Sb, Sc, Sm, and Th in all the samples were below 1 mg·g⁻¹. Classification of these heroin samples was achieved by the application of hierarchical cluster analysis. The results show that NAA can provide useful information on the origin of the illicit drugs. This revised version was published online in July 2006 with corrections to the Cover Date.     

Determination of certain elements in human serum albumin by neutron activation analysis

Instrumental activation analysis was used to determine the contents of certain elements in human serum albumin (HSA). Sample irradiation was performed with a thermal neutron flux of 1.5·10¹³ n·cm⁻²·sec⁻¹ in the RA nuclear reactor of the Boris Kidrič Institute, Vinča. Measurements were performed on a 4096-channel analyser with a high-resolution Ge(Li) detector. The Na, Cu, Br, Au, Hg, Cr, Fe, Ag, Sc, Ba and Co contents were determined in HSA produced by the Institute for Blood Transfusion, Belgrade.     

Determination of trace elements in high purity copper by INAA, GFAAS and ICP/AES

Trace impurity elements in high purity copper metal (4 mine class) put on the market were analyzed by Instrumental Neutron Activation Analysis (INAA) and the results compared with those from Graphite Furnace Atomic Absorption Spectrophotometry (GFAAS) and Inductively Coupled Plasma Atomic Emission Spectrophotometry (ICP-AES). The sample irradiation was done at the irradiation facilities (thermal neutron flux, 5·10¹² n·cm⁻²·s⁻¹) of the TRIGA Mark-III research reactor in the Korea Atomic Energy Research Institute. Four unalloyed copper standards (NIST SRM # 393, 394, 395 and 398) were used to identify the accuracy and precision of the analytical procedure. The homogeneity of samples was assessed by means of the elements such as Ag, As, Co, Sb, Se and Zn. The analytical results of INAA, GFAAS and ICP-AES were in good agreement within expected uncertainties each other and showed the possibility of using them for the analytical quality control.     

Trace element distributions in man-made fibers

A preliminary study to evaluate the use of neutron activation analysis for the characterization of six groups of man-made fibers for forensic purposes has been made. A total of 81 samples of acetate, acrylic, modacrylic, nylon, polyester and rayon were analyzed. Small samples, approximately the size typically found during a crime scene search, were analyzed using a Ge(Li) detector system following a 20 min irradiation at a flux of 5·10¹³ n·cm⁻²·sec⁻¹. The following elements were determined quantitatively in one or more of the samples: Ti, Sr, Au, Zn, Sb, Br. Mn, Mg, Cu, In, Co, Cu, V, K, Al, Cl, Na, Ca, and S. Significant qualitative and quantitative differences were found both between and within the six groups. However, within certain groups some fibers from different manufacturers showed marked similarities in qualitative and quantitative composition.     

Aktivierungsanalytische Bestimmung von Chrom und Zink in biologischem Material

An activation analysis method has been developed for the determination of chromium and zinc in biological material. After the samples had been activated in a thermal flux of 7·10¹¹ n·cm⁻²·sec⁻¹ for 100 hours, both elements were separated from interfering radionuclides by means of ion-exchange and distillation processes. Gamma spectrometry was used to measure the activities of⁵¹Cr and⁶⁵Zn. The practical limits of detection were found to be 1·10⁻⁸ g for chromium and 1·10⁻⁷ g for zinc. The results of model experiments and of the analysis of blood taken from two individuals proved to be accurate and reproducible.      

A study of the elemental composition of diabases by instrumental neutron activation and X-ray fluorescence analysis

The distribution of the elemental composition was studied mainly for microelements in the diabases of the Pechenga suite subjected to various changes. Investigations were conducted by a combination of instrumental neutron activation INAA and X-ray fluoresence XRFA analyses. The INAA was conducted with sample weights of 20–100 mg exposed to irradiation in a nuclear reactor by a flux of neutrons ≈10¹³ n·cm⁻²·s⁻¹. Measurements were carried out by means of a semi-conductor gamma-spectrometer with a Ge(Li) detector. The determination of Al, Mn, Mg, Ti, V, Ca was conducted by short-lived isotopes, while the determination of Na, Sc, Fe, Co, Cr, Hf, Th, La, Ce, Sm, Eu, Yb, Lu by longlived ones. For XRFA samples weighing up to 2 g were irradiated by means of an¹⁰⁹Cd isotope source and were measured by a spectrometer with a Si(Li) detector and beryllium window. By this method we determined the Sr, Zr an Nb contents. Continuous distribution histograms were plotted for the concentration of 22 elements and some of their ratios. Considerable variations in microelemental composition observed in a number of cases make it possible to assess the character of past processes of diabasic change.     

Determination of chromium in blood by neutron activation analysis

A procedure for the determination of chromium in blood has been developed with a sensitivity of 5×10⁻³ μg Cr. Dried blood was irradiated with a neutron flux of 10¹² n·cm⁻²·sec⁻¹ in the VVRS reactor for 4 weeks, then the sample was mineralized and the chromium isolated by extraction as perchromic acid. The determination of the chromium content was accomplished by measuring the 0.32 MeV gamma energy of⁵¹Cr. In order to make correction for the interfering reaction⁵⁴Fe(n,α)⁵¹Cr, the formation of chromium from high-purity iron was investigated. The chromium content of the blood samples was between 1.03×10⁻² and 5.2×10⁻² ppm Cr.     

Determination of trace elements in water by non-destructive neutron activation

A systematic study was undertaken in order to find out which of the most relevant elements can be determined in water under normal conditions by non-destructive neutron activation simultaneously using a suitable monostandard method. Standardized water samples as well as natural water of different kind were used, brought to dryness by freeze-drying and irradiated in quartz at a neutron flux of 10¹⁴ cm⁻² s⁻¹ for 1 day. The trace element content in quartz ampoules of different origin was determined separately. The following elements are discussed in detail including possible interferences: As, Au, Br, Ca, Cd, Co, Cr, Cu, Eu, Fe, Hg, K, La, Mo, Na, Ni, Sb, Sc, Se, U, Zn. Presented at the Euroanalysis II Conference, Budapest, 25–30. Aug. 1975.     

Determination of 22 elements in geological samples by instrumental neutron activation analysis

An instrumental neutron activation analysis (INAA) method has been developed for multi-element determination in geological samples. The INAA method consists of irradiation of samples for 90 sec at a flux of 1.0·10¹² n·cm⁻²·sec⁻¹ and determination of 12 elements by using their short-lived nuclides. Samples have been re-irradiated for 3 hrs for measuring concentrations of another 10 elements. Precision and accuracy of the INAA method have been evaluated by analysing samples and USGS standard reference materials. Precision and accuracy are within±15% and ±10%, respectively.     

Instrumental neutron activation analysis of gunpowder residues

A procedure has been developed for the detection of gunpowder residues deposited on the hand of a person firing a gun. The method is based on neutron activation analysis of the antimony level on the surface of the hand. The surface materials are removed by a film made by spraying a 4% solution of cellulose acetate in acetone, which sets to form a thin film that can readily be stripped off. This technique was found to be preferable to the paraffin-lift technique which is in common use. Following neutron activation of the film in a nuclear reactor, antimony is assayed by high-resolution Ge(Li) spectrometry without prior chemical processing. The sensitivity of the method is about 5·10⁻⁹ g Sb, with a precision of about ±10% at a neutron flux of 5·10¹³ n·cm⁻²·sec⁻¹. Analysis of twenty samples taken from the hands of persons who had fired a pistol gave Sb levels of 0.4±0.2 μg, compared with 0.024±0.013 μg found on the hands of persons who had not fired a revolver. The possible extension of the present technique to include the determination of additional elements is discussed. Project carried out with the support of the Office of the Chief Scientist to the Ministry of Defense and with the collaboration of the Israel Police.     

Analysis of phosphate rock samples for vanadium using accelerator-based thermal neutrons

Extensive sedimentary phosphate deposits exist in the Sirhan-Turayf basin in northwestern Saudi Arabia containing significant amounts of uranium, thorium, vanadium and rare earth elements. The determination of the concentration and pattern of distribution of some of these elements is essential for economic aspects. This study reports the analysis of vanadium in selected phosphate rock samples from the basin using accelerator-based thermal neutrons activation analysis (TNAA). Samples were irradiated in a thermal neutron flux of 2.5·10⁶ n·cm⁻²·s⁻¹. The induced activity was measured with a HP-GMX detector coupled to a PC-based data acquisition and analysis system. The facility was calibrated using certified standards of vanadium. The minimum detection limit of vanadium was about 1 mg. Three independent measurements on each sample yielded comparable results indicating the reliability of the technique. The vanadium concentrations in the samples vary from 23 to 457 ppm. This revised version was published online in July 2006 with corrections to the Cover Date.     

Multi-element analysis of biological samples after intense neutron irradiation an fast chemical separation

For the simultaneous determination of many elements in small biological samples, a multi-element analysis has been developed using neutron activation. After a 24-hr irradiation in a neutron flux of 2.5·10¹⁴ n·cm⁻²·sec⁻¹ and after immediate chemical separation without cooling, it was possible to analyse 24 elements in bovine liver (NBS-SRM 1577). The separation apparatus, set up in a shielded cell can work four samples simultaneously, and its operation is fast enough to allow the detection of radioisotopes with a half-life of about 2 hrs (¹⁶⁵Dy,^57mSr,⁵⁶Mn). Amounts lower than 10⁻³ μg of Dy, Eu, Pr, Sm and Yb were determined.     

Determination of trace elements in carbonates by instrumental neutron activation analysis

A systematic non-destructive determination of eighteen trace elements (F, Na, Cl, Sc, Mn, Zn, Br, Sr, I, Ba, La, Ce, Sm, Eu, Tb, Yb, Th and U) in carbonate samples by thermal neutron activation analysis was developed. Three 0.2–0.5g samples were irradiated for 15 sec (in the case of determination of F), for 3 min (in the case of Na, Cl, Mn, Sr and I) and for 60 hrs (in the case of Sc, Zn, Br, Ba, La, Ce, Sm, Eu, Tb, Yb, Th and U) in the TRIGA MARK II Reactor at a thermal neutron flux of 5·10¹¹ n·cm⁻²·sec⁻¹ (15 sec and 3 min irradiation) and 1.5·10¹²n·cm⁻²·sec⁻¹ (60 hrs irradiation), respectively. According to the half life of the nuclides formed, the activities were measured with a Ge(Li) spectrometer as follows,²⁰F∶15 sec counting after 20–25 sec cooling,²⁴Na,³⁸Cl,⁵⁶Mn,^87mSr and¹²⁸I∶600 sec couting after 30–120 min cooling,⁸²Br,¹⁴⁰La,¹⁵³Sm,¹⁷⁵Yb and²³⁹Np (daughter of²³⁹U)∶3000 sec counting after 1 week cooling,⁴⁶Sc,⁶⁵Zn,¹³¹Ba,¹⁴¹Ce,¹⁵²Eu,¹⁶⁰Tb and²³³Pa (daughter of²³³Th)∶5000 sec counting after 1 month cooling. The errors due to the fluctuation of the neutron flux and the counting geometry were minimized by the use of calcium determined previously with EDTA-titration as an internal standard. The interferences from²⁴Mg(n, p)²⁴Na and²³⁵U(n, fission) reactions were corrected by the activities produced by the reactions in unit weight of magnesium and uranium, and their concentrations in samples measured experimentally. The data of Na, Mn, Zn and Sr were compared with the results obtained by atomic absorption analysis.     

Detection limits in epithermal neutron activation analysis of geological material

The improvement of detection limits for trace elements in geological samples by epithermal neutron activation analysis is examined. The relative merits of cadmium, boron and composite cadmium+boron filters are compared for trace elements Ni, As, Pd, Cd, Sb, W, Ir, Pt and Au, and interfering elements Na, K, Sc, Cr, Fe, Co and Cu. A boron filter gives optimum sensitivity for the trace elements based on interference from⁴⁶Sc, but the detection limits are only improved 2–5 times. Ma imum possible improvement, which is shown by Ni, gives sensitivities 5 times better under cadmium and 15 times under boron.     

The determination of rare earth alloying additives in special steels by neutron activation analysis

A procedure for neutron-activation analysis of cerium, lanthanum, praseodymium and neodymium, tested on more than thirty samples of steels, is described. After irradiation for 20 hrs with a neutron flux of 1.2·10¹³ n·cm⁻²·sec⁻¹ the steel samples were dissolved in aqua regia and extraction separation of iron from 6N HCl by ether was employed. The REE were separated as a group by precipitation as fluorides and hydroxydes. The individual rare-earth elements were separated from each other using a KU-2 cation exchange resin and a solution of ammonium α-hydroxyisobutirate as eluant. The separated samples were counted on a NaI(T1) γ-spectrometer.     

Determination of phosphorus in polymers by INAA

An INAA technique employing beta spectrometry was developed for the determination of phosphorus in polymers. The (n,γ) reaction on phosphorus produces³²P, half-life 14.3 days, a pure beta emitter with end-point energy 1.71 MeV. Polymer samples in the form of powders, films and pellets are irradiated and then counted with a plastic scintillator. The beta spectrum is corrected for interferences (especially Sb, Zn and Br which are quantified by gamma spectrometry) and for energy loss in the thick sample. Samples must also be analyzed for S and Cl which cause nuclear interferences. With an irradiation time of 4 hours at a neutron flux of 5·10¹¹ n·cm^{−2 s −1}, decay time 10 days and counting time 10 minutes, the sensitivity is 520 counts/μg phosphorus and the detection limit is typically 2μg/g.     

Etude de quelques reactions nucleaires induites par les neutrons rapides de pile

Conclusion Dans une première partie, l’étude des réactions engendrées par les neutrons rapides de pile sur douze éléments a montré que certaines de celles-ci pouvaient être utilisées pour un dosage quantitatif. Dans une seconde partie, nous proposons un dosage radiochimique du silicium par la réaction²⁸Si(n, p)²⁸Al qui a, dans nos conditions de travail, sa limite de détermination à 620 μg. A titre de comparaison, signalons que cette limite se situe par irradiation avec des neutrons de 14 MeV, produits au moyen d’un accélérateur (flux de 5·10⁸ n·cm⁻²·sec⁻¹), à environ 10 μg. Le dosage non destructif du silicium dans le diméthylpolysilane est décrit.

---

In the first part, the fast-neutron flux available in reactor cores was utilized to define experimentally the sensitivity for the determination of 12 different elements, based on fast-neutron nuclear reactions. The fluxes available with our AGN-201 P reactor are in the range of 10⁹–10¹⁰ n·cm⁻²·sec⁻¹ in the 1–4 MeV region. A good sensitivity was obtained for²⁷Al,⁵²Cr,⁵⁶Fe,²⁸Si,²³Na [by (n, p) reaction],²⁷Al,³¹P,⁸⁹Y [by (n, α) reaction] and¹⁹⁷Au,¹⁸³W,⁸⁹Y [by (n, n′) reaction]; the elements Cl, Ca, Pb failed to give reactions. In the second part, a non-destructive method for the determination of silicium based on the reaction²⁸Si(n, p)²⁸Al is proposed. The limit of determination is about 0.6 mg for a neutron flux of 10⁹ n·cm⁻²·sec⁻¹. As an example, Si in dimethylpolysilane was determined.

     

A method for the determination of Mn,Cu, Zn,K and Na in small tissue biopsies by neutron activation analysis

A method has been worked out for the determination of Mn, Cu, Zn, K and Na in tissue biopsies weighing between 10 and 50 mg. The samples were dried, packed in polyethylene containers and irradiated at a flux of 1.8·10¹² n·cm⁻²·sec⁻¹ for 48 hrs. They were dissolved and separated into five fractions by ion exchange chromatography. Managenese was precipitated and counted as MnO₂ and zinc as quinaldate. Copper and potassium were counted in solution. Sodium was taken up in hydrated antimony pentoxide (HAP) and counted in that stage. Accuracy, precision and specificity were determined by recovery experiments and by analysis ofBowen's biological standard.