Polyaddition of bifunctional 1,3‐benzoxazine and 2‐methylresorcinol

A polyaddition system consisted of a bifunctional N‐n‐propyl benzoxazine and 2‐methylresorcinol ( MR ) that proceeds at ambient temperature has been developed. In this system, the aromatic ring of MR acted as a bifunctional monomer, reacting with a two equivalent amount of benzoxazine moieties via their ring‐opening reaction. The polyaddition gave the corresponding linear polymer bearing phenolic moieties bridged by Mannich‐type linkage in the main chain. The linear polymer had a high glass transition temperature, which was comparable to that of the linear polybenzoxazine synthesized by the ring‐opening polymerization of a monofunctional N‐n‐propyl benzoxazine. The employment of a bifunctional N‐allyl benzoxazine in the polyaddition system resulted in the formation of the corresponding polymer with allyl pendants, which exhibited improved heat resistance due to its thermally induced crosslinking reaction. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3867–3872     

Synthesis of polymers bearing 1,3‐benzoxazine moiety in the side chains from poly(allylamine) and their crosslinking behaviors

A polymer bearing 1,3‐benzoxazine moiety in the side chain was synthesized successfully from poly(allylamine) based on a stepwise strategy consisted of three steps: (1) treatment of poly(allylamine) with salicylaldehyde to convert the amino group in the side chain into the corresponding o‐(iminomethyl)phenol moiety, (2) reduction of the o‐(iminomethyl)phenol to obtain the corresponding o‐(aminomethyl)phenol moiety, and (3) formation of 1,3‐benzoxazine moiety by the reaction of the o‐(aminomethyl)phenol with formaldehyde. The content ratio of benzoxazine moieties and o‐(aminomethyl)phenol moieties in the polymer were tunable by varying amount of formaldehyde. The presence of o‐(aminomethyl)phenol moieties exhibited a significant promoting effect on the crosslinking reaction. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Cationic polymerization of seven‐membered cyclic monothiocarbonate 1,3‐dioxepan‐2‐thione

The cationic ring‐opening polymerization of a seven‐membered cyclic monothiocarbonate, 1,3‐dioxepan‐2‐thione, produced a soluble polymer through the selective isomerization of thiocarbonyl to a carbonyl group {? [SC(C?O)O(CH₂)₄]_n? }. The molecular weights of the polymer could be controlled by the feed ratio of the monomer to the initiators or the conversion of the monomer during the polymerization, although some termination reactions occurred after the complete consumption of the monomer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1014–1018, 2005     

Methylol‐functional benzoxazines as precursors for high‐performance thermoset polymers: Unique simultaneous addition and condensation polymerization behavior

A new class of high‐performance resins of combined molecular structure of both traditional phenolics and benzoxazines has been developed. The monomers termed as methylol‐functional benzoxazines were synthesized through Mannich condensation reaction of methylol‐functional phenols and aromatic amines, including methylenedianiline (4,4′‐diaminodiphenylmethane) and oxydianiline (4,4′‐diaminodiphenyl ether), in the presence of paraformaldehyde. For comparison, other series of benzoxazine monomers were prepared from phenol, corresponding aromatic amines, and paraformaldehyde. The as‐synthesized monomers are characterized by their high purity as judged from ¹H NMR and Fourier transform infrared spectra. Differential scanning calorimetric thermograms of the novel monomers show two exothermic peaks associated with condensation reaction of methylol groups and ring‐opening polymerization of benzoxazines. The position of methylol group relative to benzoxazine structure plays a significant role in accelerating polymerization. Viscoelastic and thermogravimetric analyses of the crosslinked polymers reveal high T_g (274–343 °C) and excellent thermal stability when compared with the traditional polybenzoxazines. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of 9,9‐bis(4‐aminophenyl)fluorene‐based benzoxazine and properties of its high‐performance thermoset

A benzoxazine ( P‐bapf ) based on 9,9‐bis(4‐aminophenyl)fluorene (BAPF), phenol, and formaldehyde was successfully prepared using two‐pot and one‐pot procedures. In the two‐pot approach, BAPF initially reacted with 2‐hydroxybenzaldehyde, leading to 9,9‐bis(4‐(2‐hydroxybenzylideneimino)phenyl)fluorene. The imine linkages of 9,9‐bis(4‐(2‐hydroxybenzylideneimino)phenyl)fluorene were then reduced by sodium borohydride, forming 9,9‐bis(4‐(2‐hydroxybenzylamino)phenyl)fluorene. Finally, paraformaldehyde was added to induce ring closure condensation, forming benzoxazine ( P‐bapf ). In the one‐pot approach, P‐bapf was obtained directly by reacting BAPF, phenol, and paraformaldehyde in various solvents. Among the solvents, we found that using toluene/ethanol (2/1, v/v) as a solvent leads to the best purity and yield. No gelation was observed in the preparation. The structure of the resulting benzoxazine was confirmed by ¹H, ¹³C, ¹H? ¹H and ¹H? ¹³C NMR spectra. P‐bapf exhibits a photoluminescent emission at 395 nm under an excitation of 275 nm. After curing, the resulting P‐bapf thermoset exhibits T_g as high as 236 °C, and the T_g can be further increased to 260 °C by copolymerization with an equal equivalent of cresol novolac epoxy. The 5% degradation temperature of the P‐bapf thermoset reaches as high as 413 °C (N₂) and 431 °C (air). The refractive index at 589 nm is as high as 1.70, demonstrating a high refractive index characteristic of fluorene linkage. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Acceleration effect of N‐allyl group on thermally induced ring‐opening polymerization of 1,3‐benzoxazine

Thermally induced ring‐opening polymerization of monofunctional N‐allyl‐1,3‐benzoxazine 1a was compared with that of N‐(n‐propyl)‐1,3‐benzoxazine 1b to clarify an unexpected effect of allyl group to promote the polymerization, that is, in spite of the comparable bulkiness of allyl group to n‐propyl group, the polymerization of 1a was much faster than that of 1b . Such a difference in polymerization rate was also observed similarly in the comparison of thermally induced polymerization of a bifunctional N‐allyl‐benzoxazine 2a with that of a bifunctional N‐(n‐propyl) analogue 2b . These observations implied a certain contribution of an electron‐rich C? C double bond of the N‐ally group to promotion of the ring‐opening reaction of 1,3‐benzoxazine into the corresponding zwitterionic species, which would involve a mechanism to stabilize the cationic part of the zwitterionic species based on “neighboring group participation” of the C? C double bond. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Promoting effect of thiophenols on the ring‐opening polymerization of 1,3‐benzoxazine

Thiophenol and p‐nitrothiophenol were evaluated as promoters for the ring opening polymerization of benzoxazine. The ring‐opening polymerization of p‐cresol type monofunctional N‐phenyl benzoxazine 1a with 10 mol % of thiophenols proceeded at 150 °C, leading to the high conversion of 1a more than 95% within 5 h, whereas the polymerization of 1a without thiophenols did not proceed under the same conditions. The promotion effect of the thiophenols on curing of bisphenol‐A type N‐phenyl benzoxazine 1b was also investigated. In the differential scanning calorimetric (DSC) analysis of the polymerization of 1b at 150 °C without using any promoters, an exothermic peak attributable to the ring‐opening reaction of benzoxazine was observed after 8 h. In contrast, in the DSC analysis of the polymerization of 1b with addition 20 mol % of p‐nitrothiophenol, an exothermic peak was observed within 2 h, to clarify the significant promoting effect of p‐nitrothiophenol. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2523–2527     

Synthesis and curing of amino‐containing benzoxazine as a novel hardener for diglycidyl ether of bisphenol‐A

Benzoxazines containing various additional functional groups have been extensively reported to improve the properties of polybenzoxazines. In this work, a novel amino‐containing benzoxazine (PDETDA‐NH₂) was conveniently synthesized from diethyltoluenediamine (DETDA), 2‐hydroxybenzaldehyde, and paraformaldehyde and was used as a hardener for diglycidyl ether of bisphenol‐A (DGEBA). The curing behaviors of PDETDA‐NH₂ and PDETDA‐NH₂/DGEBA systems were studied by DSC, FT‐IR, and ¹H NMR. When curing, PDETDA‐NH₂ was firstly polymerized to N,O‐acetal‐type polymer and then rearranged to Mannich‐type polymer at elevated temperature, while the addition reaction between amino and benzoxazine was discouraged because of the steric hindrance of alkyl substituents. During PDETDA‐NH₂/DGEBA curing, it was found that the reactions happened in the order of addition polymerization of amino and epoxide, ring‐opening polymerization of benzoxazine, etherification between phenolic hydroxyl of the polymerized benzoxazine, and epoxide. Compared with DETDA cured DGEBA, PDETDA‐NH₂ cured DGEBA showed higher modulus, higher char yield, and much lower water uptake.     

ε‐Caprolactone polymerization under air by the biocatalyst: Magnesium 2,6‐di‐tert‐butyl‐4‐methylphenoxide

This study investigated the synthesis of the biocatalyst, magnesium 2,6‐di‐tert‐butyl‐4‐methylphenoxide (Mg(BHT)₂) complex, and the ring‐opening polymerization (ROP) of ε‐caprolactone (CL). The complex demonstrates high catalytic activity and controllable of molecular weight for the ROP of CL in tetrahydrofuran at room temperature, even when polymerization was performed under air. Before this study, the polymerization of CL had never been performed using a magnesium catalyst under air at room temperature. Various forms of alcohols with different purposes were also used as initiators with Mg(BHT)₂. The results show that the magnesium complex acts as a perfect catalyst because of its high catalytic activity and control ability without any cytotoxicity in the polymerization of CL, making it suitable for biomedical applications. In addition, nanoparticle formation, cytotoxicity, and phototoxicity of tri‐2‐hydroxyethyl ester [Ce6‐(CH₂CH₂OPCL)₃] were also studied in this article and Ce6‐(CH₂CH₂OPCL)₃ formed nanoparticle can act as a nanophotosensitizer for photodynamic therapy. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and crosslinking reaction of a novel polymer containing benzoxazine and phenyleneethynylene moieties in the main chain

A novel polymer, poly( 1 ) containing benzoxazine and phenyleneethynylene moieties in the main chain with number‐average molecular weights ranging from 1400 to 9800 was obtained quantitatively by the Sonogashira–Hagihara coupling polymerization of the corresponding iodophenyl‐ and ethynylphenyl‐substituted monomer 1 . Poly( 1 ) was heated at 200 °C under N₂ for 2 h to obtain the cured polymer, poly( 1 )′ via the ring‐opening polymerization of the benzoxazine moieties. The structures of the polymer before and after curing were confirmed by ¹H‐NMR, IR, and UV–vis absorption and reflectance spectroscopies. Poly( 1 )′ was thermally more stable than monomer 1 and poly( 1 ). A specimen was prepared from a mixture of poly( 1 ) and phenol‐diaminodiphenylmethane type benzoxazine 2 by heating at 200 °C for 2 h under N₂. The poly( 1 )/ 2 resin was thermally stable than bisphenol‐A type benzoxazine resin 3 . Poly( 1 ) exhibited XRD peaks corresponding to the d‐spacings of 1.26–0.98 and 0.40 nm, assignable to the repeating monomer unit and alignment of polymer molecules, respectively. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2581–2589     

Cationic ring‐opening polymerization of ϵ‐thionocaprolactone: Selective formation of polythioester

Cationic ring‐opening polymerization of ϵ‐thionocaprolactone was examined. The corresponding polythioester with the number‐average molecular weight (M_n ) of 57,000 was obtained in the polymerization with 1 mol % of BF₃ · OEt₂ as an initiator in CH₂Cl₂ at 28 °C for 5 h with quantitative monomer conversion. The M_n of the polymer increased with the solvent polarity and monomer‐to‐initiator ratio. No polymerization took place below −30 °C, and the monomer conversion and M_n of the polymer increased with the temperature in the range of −15 to 28 °C. The increase of initial monomer concentration was effective to improve the monomer conversion and the M_n of the obtained polymer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4057–4061, 2000     

Highly efficient catalysts‐acetylacetonato complexes of transition metals in the 4th period for ring‐opening polymerization of 1,3‐benzoxazine

Acetylacetonato (acac) complexes of transition metals in the 4th period were examined as catalysts for the ring‐opening polymerization of benzoxazine. This examination revealed that acac complexes of manganese, iron, and cobalt exhibited the highest activity, which was comparable or slightly higher than that exhibited by p‐toluenesulfonic acid. By replacing acac ligand by hexafluoroacetylacetonato (F₆‐acac) ligand, the activity of manganese and iron complexes was remarkably enhanced. These metal F₆‐acac complexes were tolerant to moisture to allow their use under air without special caution. Another advantage was their negligible effect to promote unfavorable weight loss during the polymerization. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 479–484, 2010     

Anionic ring‐opening polymerization of a five‐membered cyclic carbonate having a glucopyranoside structure

Anionic ring‐opening polymerizations of methyl 4,6‐O‐benzylidene‐2,3‐O‐carbonyl‐α‐D ‐glucopyranoside (MBCG) were investigated using various anionic polymerization initiators. Polymerizations of the cyclic carbonate readily proceeded by using highly active initiators such as n‐butyllithium, lithium tert‐butoxide, sodium tert‐butoxide, potassium tert‐butoxide, and 1,8‐diazabicyclo[5.4.0]undec‐7‐ene, whereas it did not proceed by using N,N‐dimethyl‐4‐aminopyridine and pyridine as initiators. In a polymerization of MBCG (1.0 M), 99% of MBCG was converted within 30 s to give the corresponding polymer with number‐averaged molecular weight (M_n) of 16,000. However, the M_n of the polymer decreased to 7500 when the polymerization time was prolonged to 24 h. It is because a backbiting reaction might occur under the polymerization conditions. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Chemistry of 2‐oxazolines: A crossing of cationic ring‐opening polymerization and enzymatic ring‐opening polyaddition

Chemistry of 2‐oxazolines is involved in the polymer synthesis fields of cationic ring‐opening polymerization (CROP) and enzymatic ring‐opening polyaddition (EROPA), although both polymerizations look like a quite different class of reaction. The key for the polymerization to proceed is combination of the catalyst (initiator) and the design of monomers. This article describes recent developments in polymer synthesis via these two kinds of polymerizations to afford various functional polymers having completely different structures, poly(N‐acylethylenimine)s via CROP and 2‐amino‐2‐deoxy sugar unit‐containing oligo and polysaccharides via EROPA, respectively. From the viewpoint of reaction mode, an acid‐catalyzed ring‐opening polyaddition (ROPA) is considered to be a crossing where CROP and EROPA meet. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1251–1270, 2010     

Cationic polymerizations of 2‐alkyloxazolines catalyzed by bismuth salts

Acidic bismuth salts, such as BiCl₃, BiBr₃, BiJ₃, and Bi‐triflate catalyzed the ring‐opening polymerization of 2‐methoxazoline (MOZ) in bulk at 100 °C, whereas less acidic salts such as Bi₂O₃ or Bi(III)acetate did not. Bi‐triflate‐catalyzed polymerizations of 2‐ethyloxazoline (EtOZ) were performed with variation of the monomer–catalyst ratio (M/C). It was found that the molecular weights were independent of the M/C ratio. The formation of cationic chain ends and the absence of cycles was proven by reactions of virgin polymerization products with N,N‐dimethyl‐4‐aminopyridine or triphenylphosphine. The resulting polymers having modified cationic chain ends were characterized by ¹H NMR spectroscopy and MALDI‐TOF mass spectrometry. The polymerization mechanism including chain‐transfer reactions is discussed. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4777–4784, 2008     

Polymerization of 2‐pentene with Ni(II) α‐diimine complex/M‐MAO catalyst and structure of the polymer

Polymerization of 2‐pentene with [ArN?C(An)C(An)·NAr)NiBr₂ (Ar?2,6‐iPr₂C₆H₃)] ( 1‐Ni) /M‐MAO catalyst was investigated. A reactivity between trans‐2‐pentene and cis‐2‐pentene on the polymerization was quite different, and trans‐2‐pentene polymerized with 1‐Ni /M‐MAO catalyst to give a high molecular weight polymer. On the other hand, the polymerization of cis‐2‐butene with 1‐Ni /M‐MAO catalyst did not give any polymeric products. In the polymerization of mixture of trans‐ and cis‐2‐pentene with 1‐Ni /M‐MAO catalyst, the M_n of the polymer increased with an increase of the polymer yields. However, the relationship between polymer yield and the M_n of the polymer did not give a strict straight line, and the M_w/M_n also increased with increasing polymer yield. This suggests that side reactions were induced during the polymerization. The structures of the polymer obtained from the polymerization of 2‐ pentene with 1‐Ni /M‐MAO catalyst consists of ? CH₂? CH₂? CH(CH₂CH₃)? , ? CH₂? CH₂? CH₂? CH(CH₃)? , ? CH₂? CH(CH₂CH₂CH₃)? , and methylene sequence ? (CH₂)_n? (n ≥ 5) units, which is related to the chain walking mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2858–2863, 2008     

Bismuth halide‐catalyzed polymerizations of ε‐caprolactone

In contrast to BiF₃, the other three Bi‐halides catalyzed the ring‐opening polymerization of ε‐caprolactone (ε‐CL) in bulk. A temperature of 140 °C was found to be advantageous for rapid polymerization and optimum molecular weights. At this temperature, the reactivity of the catalysts increases in the order BiCl₃ < BiBr₃ < BiJ₃. Variation of the monomer‐catalyst ratio (M/C) yielded number‐average molecular weights (M_ns) up to 80,000 Da (corrected SEC data, 120,000 Da uncorrected), but a proper control of the M_ns was not achieved. In addition to CH₂? OH endgroups, CH₂Cl, CH₂Br, and CH₂J endgroups were detected, but no evidence for a cationic polymerization mechanism was found. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7483–7490, 2008     

Ring‐opening polymerization of benzylated 1,6‐anhydro‐β‐D‐lactose and specific biological activities of sulfated (1→6)‐α‐D‐lactopyranans

A new anhydro disaccharide monomer, 1,6‐anhydro‐2,3‐di‐o‐benzyl‐4‐o‐(2′,3′,4′,6′‐tetra‐o‐benzyl‐β‐D ‐galactopyranosyl)‐β‐D ‐glucopyranose (benzylated 1,6‐anhydro lactose (LSHBE)), was synthesized from D ‐lactose to investigate the polymerizability and biological activities of the resulting branched polysaccharides. The ring‐opening polymerization of LSHBE was carried out with phosphorus pentafluoride as a catalyst under high vacuum to give a stereoregular benzylated (1 → 6)‐α‐D ‐lactopyranan. The molecular weights of poly(LSHBE)s increased with an increase in the amount of CH₂Cl₂ solvent, and polymerization temperatures were affected in both molecular weights and yields of the polymers. The copolymerization of LSHBE with benzylated 1,6‐anhydro‐β‐D ‐glucopyranose (LGTBE) gave the corresponding copolysacchrides having different proportions of lactose and glucose units in good yields. After debenzylation to recover hydroxyl groups and then sulfation, sulfated homopoly(lactose)s and copoly(lactose and glucose)s were obtained. Sulfated homopoly(lactose)s had moderate anti‐HIV (EC₅₀ = 5.9 and 1.3 μg/mL) and blood anticoagulant activities (AA = 18 and 13 unit/mg), respectively. Sulfated copoly(lactose and glucose) having 15 mol % lactose units gave high anti‐HIV and blood anticoagulant activities of 0.3 μg/mL and 54 unit/mg, respectively. These biological results suggest that the distance between branched units on the main chain plays an important role in the anti‐HIV and blood anticoagulant activities. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 913–924, 2009     

Study of hydrogen bonding and thermal properties of polybenzoxazine and poly‐(ε‐caprolactone) blends

The thermal properties of physical blends containing benzoxazine monomer and polycaprolactone (PCL) were monitored by DSC and Fourier transform infrared spectroscopy (FTIR). The ring‐opening reaction and subsequent polymerization reaction of the benzoxazine were facilitated significantly by the presence of a PCL modifier. Hydrogen‐bond formation between the hydroxyl groups of polybenzoxazine and the carbonyl groups of PCL was evident from the FTIR spectra. Only one glass‐transition temperture (T_g) value was found in the composition range investigated, and the T_g value of the resulting blend appeared to be higher in the blend with a greater amount of PCL. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 736–749, 2001     

Ring opening polymerization of epoxides with urea‐derivatives of 4‐aminopyridine as thermally latent anionic initiator

In this study, a series of urea‐derivatives of 4‐aminopyridine (4AP) were evaluated as thermally latent initiators for the anionic ring‐opening polymerization of diglycidyl ether of bisphenol A (DGEBA). The urea‐derivatives were synthesized by the reactions of 4AP with the corresponding iso(thio)cyanates (phenyl isocyanate, tert‐butyl isocyanate, methylene diphenyl diisocyanate, and phenyl isothiocyanate). The ability of the urea‐derivatives as latent initiators was investigated with differential scanning calorimetry (DSC): Upon heating formulations comprised of DGEBA and the urea‐derivatives in a heating rate at 10 °C/min, the resulting DSC profiles indicated exothermic peaks to confirm that DGEBA underwent the polymerization efficiently. The corresponding DSC‐peak top temperatures (T_{peak top}) was higher than that observed for the formulation comprised of DGEBA and pristine 4AP, to clarify that the urea are useful initiators with thermal latency. A possible mechanism for the initiation step involves the thermal dissociation of the urea into 4AP and the corresponding isocyanates. 4AP thus generated readily initiated the ring‐opening polymerization of epoxide. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2518–2522