Synthesis,characterization, and proton‐conducting properties of organic–inorganic hybrid membranes based on polysiloxane zwitterionomer

The synthesis and characterization of a series of zwitterionic hybrid membranes based on a zwitterionic siloxane precursor (ZS) are described. Flexible, transparent, optically homogeneous films were prepared. With the further incorporation of poly(ethylene glycol) (PEG), the hybrid films became more flexible but translucent. The structure of the inorganic sides was probed with solid‐state ²⁹Si NMR spectroscopy, and the organic sides and the chemical process involved were characterized with solid‐state ¹³C cross‐polarization/magic‐angle spinning NMR. A higher content of ZS led to higher proton conductivity of the hybrid electrolytes. Moreover, the proton conductivity was enhanced by the addition of the plasticizing component of PEG to the hybrid matrix; this was ascribed to the increased water uptake and free volume of the hybrid matrix and the dissociation of sulfonic acid groups. The proton conductivity of these hybrid membranes could be increased up to 3.5 × 10^?2 S/cm by the temperature and relative humidity being increased to 85 °C and 95%, respectively. The proton‐conduction behavior of these hybrid membranes is also briefly discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3444–3453, 2006     

Removal of methylene blue dye from aqueous solution by semi‐interpenetrating polymer network hybrid hydrogel: Optimization through Taguchi method

In this study, sodium humate/poly(acrylamide‐co‐methacrylic acid)/kaolin semi‐interpenetrating polymer network hybrid hydrogel was synthesized as an effective adsorbent for the removal of methylene blue. The morphological and structural properties, and swelling behavior in distilled water and various environments of hybrid hydrogel were investigated with different analyses and tests. The equilibrium swelling percent of hybrid hydrogel reached to 37,000% in 240 min. The parameters (agitation time, concentration, dose, temperature, and pH) affecting adsorption process for methylene blue were optimized using Taguchi method. The data obtained in optimum conditions were well fitted to Langmuir adsorption isotherm and maximum adsorption capacity was determined as 833. 33 mg/g. In the light of the results, the utilization of hybrid hydrogel with high swelling capacity is foreseen as a favored adsorbent in several separation processes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1070–1078     

Synthesis and optical properties of σ–π conjugated organic–inorganic hybrid gels

Organic–inorganic hybrid gels containing Si‐vinylene units have been synthesized by a hydrosilylation reaction of tri‐ or tetra‐ethynyl aryl compounds, 1,3,5‐triethynylbenzene (TEB), 3,3′,5,5′‐tetraethynylbiphenyl (TEBP), or tetrakis(4‐ethynylphenyl)methane (TEPM), and bisdimethylsilyl compounds, 1,1,3,3‐tetramethyldisiloxane (TMDS) or 1,4‐bisdimetylsilylbenzene (BDMSB), in toluene. Network structure of the resulting gels was quantitatively characterized by a scanning microscopic light scattering. The reactions yielded the gels having homogeneous network structure of 1.5–2.9 nm mesh size under the monomer concentrations that were relatively higher than the critical gelation concentration. The gels obtained from TEB showed broad absorption in the range from 340 to 370 nm, and emission in the range from 440 to 490 nm. The TEB–BDMSB gels showed remarkable red shift of the emission in comparison with that of the corresponding reaction solutions derived from the network formed by σ–π conjugation. The TEPM–TMDS, BDMSB gels exited by 280 nm showed not only the emission peak at around 360 nm derived from TEPM, but the broad peak at around 420 nm, which should be derived from interaction between phenyl groups of TEPM in the gels. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1360–1368     

Synthesis of organic‐inorganic hybrid gels by means of thiol‐ene and azide‐alkene reactions

Organic–inorganic hybrid gels have been synthesized from a multi‐vinyl functional cyclic siloxane, 1,3,5,7‐tetravinyltetramethylcyclotetrasiloxane (TVMCTS), or a cubic silsesquioxane, octavinyloctasilasesquioxane (PVOSS), and α,ω‐dithiol compounds, 1,6‐hexanedithiol (HDT), 1,10‐decanedithiol (DDT), using thiol‐ene reaction in toluene. The network structure of the resulting gels, mesh size and mesh size distribution, was quantitatively characterized by means of a scanning microscopic light scattering (SMILS). The gels obtained from TVMCTS‐HDT formed homogeneous network structure with 1.5–1.6 nm mesh. Relaxation peaks derived from large clusters and/or micro gels were detected in the SMILS analysis of the TVMCTS‐DDT, PVOSS‐HDT, and PVOSS‐DDT gels besides those from the small meshes. The organic–inorganic hybrid gels were also synthesized from TVMCTS, PVOSS with α,ω‐diazide compounds, 1,6‐hexanediazide (HDA), 1,10‐decanediazide (DDA), using azide‐alkene reaction in toluene. All the gels obtained with the azide‐alkene reaction formed the homogeneous network structure. Enthalpy relaxation at the glass transition of the dried samples was detected by differential scanning calorimetry to study the network uniformity of the original gels. The gels synthesized by the azide‐alkene reaction showed larger enthalpy than the gels synthesized by the thiol‐ene reaction, indicating homogeneous network structure in the former gels. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2229–2238     

Enhanced efficiency of polyfluorene derivatives: Organic–inorganic hybrid polymer light‐emitting diodes

Two novel organic–inorganic hybrid polyfluorene derivatives, poly{(9,9′‐dioctyl‐2,7‐fluorene)‐co‐(9,9′‐di‐POSS‐2,7‐fluorene)‐co‐[2,5‐bis(octyloxy)‐1,4‐phenylene]} (PFDOPPOSS) and poly{(9,9′‐dioctyl‐2,7‐fluorene)‐co‐(9,9′‐di‐POSS‐2,7‐fluorene)‐co‐bithiophene} (PFT2POSS), were synthesized by the Pd‐catalyzed Suzuki reaction of polyhedral oligomeric silsesquioxane (POSS) appended fluorene, dioctyl phenylene, and bithiophene moieties. The synthesized polymers were characterized with ¹H NMR spectroscopy and elemental analysis. Photoluminescence (PL) studies showed that the incorporation of the POSS pendant into the polyfluorene derivatives significantly enhanced the fluorescence quantum yields of the polymer films, likely via a reduction in the degree of interchain interaction as well as keto formation. Additionally, the blue‐light‐emitting polyfluorene derivative PFDOPPOSS showed high thermal color stability in PL. Moreover, single‐layer light‐emitting diode devices of an indium tin oxide/poly(3,4‐ethylene dioxythiophene):poly(styrene sulfonate)/polymer/Ca/Al configuration fabricated with PFDOPPOSS and PFT2POSS showed much improved brightness, maximum luminescence intensity, and quantum efficiency in comparison with devices fabricated with the corresponding pristine polymers PFDOP and PFT2. In particular, the maximum external quantum efficiency of PFT2POSS was 0.13%, which was twice that of PFT2 (0.06%), and the maximum current efficiency of PFT2POSS was 0.38 cd/A, which again was twice that of PFT2 (0.19 cd/A). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2943–2954, 2006     

Synthesis and characterization of organic–inorganic hybrid block copolymers containing a fully condensed ladder‐like polyphenylsilsesquioxane

A series of inorganic–organic hybrid block copolymers were synthesized via atom transfer radical polymerization using a fully condensed, ladder‐like structured polyphenylsilsesquioxane end‐functionalized macroinitiator. The inorganic portion, ladder‐like polyphenylsilsesquioxane, was synthesized in a one‐batch, base‐catalyzed system, whereas organic hard and soft monomers, styrene, and n‐butyl acrylate, were polymerized and copolymerized on the ends of the linear, inorganic backbone. Synthesized hybrid diblock, triblock, and random copolymers were characterized by ¹H NMR, ²⁹Si NMR, gel permeation chromatography, static light scattering, Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. Hybrid block copolymers were well‐defined with low polydispersity (<1.4) and exhibited enhanced thermal properties in the form of increased glass transition and degradation onset temperatures over their organic analogues.© 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis of poly(vinylidene fluoride) (PVdF)/silica hybrids having interpenetrating polymer network structure by using crystallization between PVdF chains

High transparent and homogeneous poly(vinylidene fluoride) (PVdF)/silica hybrids were obtained by using an in‐situ interpenetrating polymer network (IPN) method. The simultaneous formation of PVdF gel resulting from the physical cross‐linking and silica gel from sol–gel process prevented the aggregation of PVdF in silica gel matrix. To form the physical cross‐linking between PVdF chains, the cosolvent system of dimethylformaide (DMF) and γ‐butyrolactone was used. The obtained PVdF/silica hybrids had an entangled combination of physical PVdF gel and silica gel, which was called a “complete‐ IPN” structure. The physical cross‐linking between PVdF chains in silica gel matrix was confirmed by differential scanning calorimetry (DSC) measurements. The miscibility between PVdF and silica phase was examined by scanning electron microscopy (SEM) and tapping mode atomic force microscopy (TM‐AFM) measurements. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3543–3550, 2005     

An organic–inorganic hybrid compound containing imidazolium cations and a one‐dimensional lithium hexacyanidocobaltate‐based anionic framework

An organic–inorganic hybrid compound, catena‐poly[bis(3H‐imidazol‐1‐ium) [[tetracyanido‐κ⁴C‐cobalt(III)]‐μ‐cyanido‐κ²C:N‐[diaqualithium(I)]‐μ‐cyanido‐κ²N:C]], {(C₃H₅N₂)₂[CoLi(CN)₆(H₂O)₂]}_n, was synthesized by the reaction of Li₃[Co(CN)₆] with imidazolium chloride in aqueous solution. The compound crystallizes in the monoclinic space group C2/c (data collected at 273 K). In the crystal structure, neighbouring [Co(CN)₆]³⁻ anionic units are linked by Li⁺ cations through the cyanide groups in a trans mode, forming a one‐dimensional zigzag chain structure extending along the c axis. A three‐dimensional supramolecular network is formed through hydrogen‐bonding interactions and is further stabilized by weak CN...π interactions between the cyanide groups and the imidazolium cations.     

Organic–inorganic interpenetrating polymer networks and hybrid polymer materials prepared by frontal polymerization

Novel polyacrylamide‐based hydrogels containing 3‐(trimethoxysilyl)propyl methacrylate and/or tetraethoxy silane were synthesized by means of frontal polymerization, using ammonium persulfate as initiator, N,N′‐methylene bisacrylamide as crosslinking agent and dimethyl sulfoxide as solvent. The obtained samples were treated at pH of 2 or 5 to induce the sol–gel reaction and evaluate their swelling behavior in the conditions. The occurrence of this reaction was assessed by solid‐state NMR. Moreover, the thermal properties of the dry materials were studied by differential scanning calorimetry and thermal gravimetric analysis, and their water‐contact angles were measured. It was found that the amount of Si affects the extent of swelling and the hydrophilicity of the resulting materials. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4618–4625     

Heterogeneity of glass transition dynamics in polyurethane‐poly(2‐hydroxyethyl methacrylate) semi‐interpenetrating polymer networks

The peculiarities of segmental dynamics over the temperature range of ?140 to 180 °C were studied in polyurethane‐poly(2‐hydroxyethyl methacrylate) semi‐interpenetrating polymer networks (PU‐PHEMA semi‐IPNs) with two‐phase, nanoheterogeneous structure. The networks were synthesized by the sequential method when the PU network was obtained from poly(oxypropylene glycol) (PPG) and adduct of trimethylolpropane (TMP) and toluylene diisocyanate (TDI), and then swollen with 2‐hydroxyethyl methacrylate monomer with its subsequent photopolymerization. PHEMA content in the semi‐IPNs varied from 10 to 57 wt %. Laser‐interferometric creep rate spectroscopy (CRS), supplemented with differential scanning calorimetry (DSC), was used for discrete dynamic analysis of these IPNs. The effects of anomalous, large broadening of the PHEMA glass transition to higher temperatures in comparison with that of neat PHEMA, despite much lower T_g of the PU constituent, and the pronounced heterogeneity of glass transition dynamics were found in these networks. Up to 3 or 4 overlapping creep rate peaks, characterizing different segmental dynamics modes, have been registered within both PU and PHEMA glass transitions in these semi‐IPNs. On the whole, the united semi‐IPN glass transition ranged virtually from ?60 to 160 °C. As proved by IR spectra, some hybridization of the semi‐IPN constituents took place, and therefore the effects observed could be properly interpreted in the framework of the notion of “constrained dynamics.” The peculiar segmental dynamics in the semi‐IPNs studied may help in developing advanced biomedical, damping, and membrane materials based thereon. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 963–975, 2007     

Facile synthesis of core‐shell organic–inorganic hybrid nanoparticles with amphiphilic polymer shell by one‐step sol–gel reactions

Organic–inorganic hybrid core‐shell nanoparticles with diameters ranging from 100 to 1000 nm were prepared by a one‐pot synthesis based on base catalyzed sol–gel reactions using tetraethoxysilane and a triethoxysilane‐terminated polyethylene‐b‐poly(ethylene glycol) as reactants. Data from TEM, TGA, and solid‐state NMR analysis are in agreement with the formation of core‐shell nanoparticles with an inorganic‐rich core and an external shell consisting of an amphiphilic block copolymer monolayer. The influence of the organic–inorganic ratio, solution concentration, and postcuring temperature on core and shell dimensions of the nanospheres were investigated by TEM microscopy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1699–1709, 2008     

Unusual inorganic phase formation in ultraviolet‐curable organic–inorganic hybrid films

Inorganic–organic hybrid materials were prepared with a cycloaliphatic epoxide adduct of linseed oil with tetraethylorthosilicate (TEOS) oligomers via a cationic UV‐curing process. The TEOS oligomers were prepared in the presence of water and ethanol with hydrochloric acid as a catalyst. The TEOS oligomers were characterized with ¹H and ²⁹Si NMR and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. Hybrid films were cured, and the dynamic mechanical and thermal properties of the hybrid films were evaluated as a function of the TEOS oligomer content. The morphology of the hybrid films was examined with atomic force microscopy, transmission electron microscopy, and small‐angle light scattering. The microscopy and dynamic mechanical data indicated that the hybrid films were heterogeneous materials with various inorganic particle sizes dispersed within the organic matrix. In addition, ²⁹Si solid‐state NMR spectroscopy was used to investigate the coupling between the silicate region and organic regions. A schematic model is proposed to address structural features of hybrid materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1607–1623, 2005     

Miscibility and properties of polyurethane/benzyl starch semi‐interpenetrating polymer networks

We successfully prepared a series of transparent materials with semi‐interpenetrating polymer networks (semi‐IPNs) from castor‐oil‐based polyurethane (PU) and benzyl starch (BS). The miscibility, morphology, and properties of the semi‐IPN films were investigated with attenuated total reflection/Fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical thermal analysis, scanning electron microscopy, wide‐angle X‐ray diffraction, electron spin resonance (ESR), ultraviolet–visible spectroscopy, and tensile testing. The results revealed that the semi‐IPN films had good or certain miscibility with BS concentrations of 5–70 wt % because of the strong intermolecular interactions between PU and BS. With an increase in the concentration of BS, the tensile strength and Young's modulus of the semi‐IPN materials increased. The ESR data confirmed that the segment volume of PU in the semi‐IPNs increased with the addition of BS; that is, the chain stiffness increased as a result of strong interactions between PU and BS macromolecules. It was concluded that starch derivatives containing benzyl groups in the side chains more easily penetrated the PU networks to form semi‐IPNs than those containing aliphatic groups, and this led to improved properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 603–615, 2005     

Simultaneous interpenetrating polymer networks based on epoxy–acrylate combinations

Simultaneous interpenetrating polymer networks (SINs) based on epoxy/poly(n-butyl acrylate) systems were synthesized at 120°C. The polymerization kinetics were studied both in situ by Fourier Transform Infrared Spectroscopy (FT–IR). Three key events occurred during the polymerization, namely the gelation of the network I, gelation of the network II, and phase separation of one polymer from the other. Thus, metastable phase diagrams describing the relations between the three events were constructed. Three-dimensional tetrahedrons characterizing the four-component system (the two monomers and the two polymers) allow the visualization of these three key events and also define some critical points, for example, the loci of the points where simultaneous gelation of the two networks occurs. The inside of the tetrahedron was also investigated using partially reacted model compounds. These tetrahedrons can be used as guidelines for setting up a synthesis strategy leading to desired morphologies. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1973–1984, 1997     

Solid polymer electrolytes. VI. Microstructure of organic–inorganic hybrid networks composed of 3‐glycidoxypropyltrimethoxysilane and LiClO4 and affected by different synthetic routes

Hybrid organic–inorganic materials derived from 3‐glycidoxypropyltrimethoxylsilane were prepared via two different synthetic routes: (1) the HCl‐catalyzed sol–gel approach of silane followed by the lithium perchlorate (LiClO₄)/HCl‐catalyzed opening of epoxide and (2) the simultaneous gelation of tin/LiClO₄‐catalyzed silane/epoxide groups. LiClO₄ catalyzed the epoxide polymerization, and its effects on the structures of these hybrid materials were studied by NMR. The structure of the inorganic side was probed by solid‐state ²⁹Si NMR spectroscopy, and the characterizations of the organic side and the chemical processes involved in the different synthetic routes were performed with solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR. The different synthetic routes significantly affected the polymerization behaviors of the organic and inorganic sides in the presence of LiClO₄. A larger amount of LiClO₄ promoted the opening of epoxide and led to the formation of longer poly(ethylene oxide) chains via the HCl‐catalyzed sol–gel approach, whereas in the case of the tin‐catalyzed approach, the faster polymerization of the inorganic side hindered the growth of the organic network. The addition of LiClO₄ was proven to be without crystalline salt present in the hybrid networks by wide‐angle X‐ray powder diffraction. Also, the interactions between the ions and hybrid host, examined with Fourier transform infrared and ⁷Li proton‐decoupled magic‐angle‐spinning NMR, further demonstrated that extensive ion aggregation existed in these hybrid materials. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 151–161, 2004     

Liquid‐crystalline organic–inorganic hybrid polymers with functionalized silsesquioxanes

Liquid‐crystalline (LC) hybrid polymers with functionalized silsesquioxanes with various proportions of LC monomer were synthesized by the reaction of polyhedral oligomeric silsesquioxane (POSS) macromonomer with methacrylate monomer having an LC moiety under common free‐radical conditions. The obtained LC hybrid polymers were soluble in common solvents such as tetrahydrofuran, toluene, and chloroform, and their structures were characterized with Fourier transform infrared, ¹H NMR, and ²⁹Si NMR. The thermal stability of the hybrid polymers was increased with an increasing ratio of POSS moieties as the inorganic part. Because of the steric hindrance caused by the bulkiness of the POSS macromonomer, the number‐average molecular weight of the hybrid polymers gradually decreased as the molar percentage of POSS in the feed increased. Their liquid crystallinities were very dependent on the POSS segments of the hybrid polymers behaving as hard, compact components. The hybrid polymer with 90 mol % LC moiety (Cube‐LC90) showed liquid crystallinity, larger glass‐transition temperatures, and better stability with respect to the LC homopolymer. The results of differential scanning calorimetry and optical polarizing microscopy showed that Cube‐LC90 had a smectic‐mesophase‐like fine‐grained texture. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4035–4043, 2001     

3D diamond‐containing nanocomposites based on hybrid polyurethane–poly(2‐hydroxyethyl methacrylate) semi‐IPNs: Composition‐nanostructure‐segmental dynamics‐elastic properties relationships

Nanostructure, glass transition dynamics and elastic properties were studied in the 3D nanodiamond‐containing composites based on polyurethane‐poly(2‐hydroxyethyl methacrylate) semi‐interpenetrating polymer networks (PU‐PHEMA semi‐IPNs), neat PU or PHEMA matrices. Nanodiamond (ND) content in the nanocomposites varied from 0.25 to 3 wt %. Combined differential scanning calorimetry/ laser‐interferometric creep rate spectroscopy/atomic force microscopy approach was utilized. A large impact of small 3D ND additives on PU‐PHEMA networks' dynamics and properties was revealed under conditions when an average inter‐particle distance L exceeds by far gyration radius R_g. The pronounced heterogeneity of glass transitions' dynamics and two opposite effects were observed. The main effect was a strong suppression of PHEMA glass transition dynamics at 90–180 °C, with the enhancement of creep resistance and threefold to sixfold increasing modulus of elasticity. The peculiarly crosslinked structure of nanocomposites, due to double covalent hybridization, resulted in low rheological percolation threshold, and a synergistic effect in dynamics was observed. Less pronounced effect of accelerating dynamics in the temperature region between β‐ and α‐transitions in PHEMA was associated with dynamics in domains with loosened molecular packing. The distinct physical limit for “anomalous” decreasing T_g is predicted in terms of the notion of the common segmental nature of α‐ and β‐relaxations. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1696–1712, 2008     

Ion-imprinted interpenetrating network gels for solid-phase extraction of heavy metal ions

In the present work, ion-imprinted interpenetrating polymer network (IPN) gels were prepared by free radical/cationic hybrid polymerisation of acrylamide (AAm) and 1,4-butanediol vinyl ether (BVE). These gels were respectively used for separation of Cu²⁺, Ni²⁺ and Zn²⁺ ions in natural water samples. Experimental conditions for effective adsorption of metal ions were optimised with respect to different experimental parameters by column procedures in detail. The optimum pH value for the adsorption of Cu²⁺, Ni²⁺ and Zn²⁺ ions on these sorbents was 6.0. Complete elution of the adsorbed metal ions from the sorbent was carried out using 1.0 mol/L of HCl solution. The optimum sample flow rate and eluent flow rate were, respectively, 1.0 and 0.3 mL/min. Common coexisting ions did not interfere with the separation and determination of the target ions. The accuracy of the proposed method was validated by analysis of the standard reference material (GBW 08301, river sediment). The measured contents of metal ions in the reference material were in good agreement with the certified values. The presented method was successfully applied for the determination of Cu²⁺, Ni²⁺ and Zn²⁺ ions in three different water samples (well water, seawater and waste water).     

Characterization of proton‐conducting organic–inorganic polymeric materials by ASAXS

The distribution of ZrO₂ and phosphotungstic acid (PTA) in a matrix of sulfonated polyether ketone was investigated by anomalous small‐angle X‐ray scattering (ASAXS). Scattering curves were obtained using X‐ray energies near the Zr and W absorption edges, allowing the independent analysis of the distribution of ZrO₂ and PTA in the sample. The interaction between both inorganic components improved their dispersion considerably when compared with films containing just one of the additives. The synergism was correlated to previous investigations concerning proton conductivity and permeability of the membranes developed for direct methanol fuel cell. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2981–2992, 2005     

Hydrogel‐like elastic membrane consisting of semi‐interpenetrating polymer networks based on a phosphorylcholine polymer and a segmented polyurethane

To obtain a hydrogel‐like elastic membrane, we prepared semi‐interpenetrating polymer networks (IPNs) by the radical polymerization of methacrylates such as 2‐methacryloyloxyethyl phosphorylcholine (MPC), 2‐hydroxyethylmethacrylate, and triethyleneglycol dimethacrylate diffused into segmented polyurethane (SPU) membranes swollen with a monomer mixture. The values of Young's modulus for the hydrated semi‐IPN membranes were less than that for an SPU membrane because of higher hydration, but they were much higher than that for a hydrated MPC polymer gel (non‐SPU). According to a thermal analysis, the MPC polymer influenced the segment association of SPU. The diffusion coefficient of 8‐anilino‐1‐naphthalenesulfonic acid sodium salt from the semi‐IPN membrane could be controlled with different MPC unit concentrations in the membrane, and it was about 7 × 10² times higher than that of the SPU membrane. Fibroblast cell adhesion on the semi‐IPN membrane was effectively reduced by the MPC units. We concluded that semi‐IPNs composed of the MPC polymer and SPU may be novel polymer materials possessing attractive mechanical, diffusive‐release, and nonbiofouling properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 68–75, 2003