Large-domain colloidal crystal films fabricated using a fluidic cell

The growth of colloidal crystal films from a dispersion of monodispersed silica spheres using a simple cell with one opening was investigated. Colloidal crystal films with large domain sizes were successfully fabricated almost over the cell (approximately 10 cm2) without applying any external force at room temperature. During the drying process, three distinct conditions were observed, in each of which the films exhibited different optical properties. Films with high transmittance were formed in the first stage. Upon further solvent evaporation, the films entered a medium transmittance state via an extremely low transmittance state. Angle-resolved reflection spectroscopy, which was used to analyze the three conditions, revealed that close-packed arrays with water-filled spaces between were formed in the first stage. One-directional flow was generated in the cell because water evaporation occurred only at the opening. The flow caused the spheres to be arranged epitaxially, resulting in a large domain size.     

Modular fluidic resistors to enable widely tunable flow rate and fluidic switching period in a microfluidic oscillator

Microfluidic systems with modular components are attractive alternatives to monolithically integrated microfluidic systems because of their flexibility. In this study, we apply the modular concept on a water‐head‐pressure‐driven microfluidic oscillator and obtain a widely tunable flow rate and fluidic switching period. Modular fluidic resistors can be easily mounted onto and demounted from a main chip by means of plastic male connectors. The connectors enable a leak‐free connection between the modular resistors and main chip (leakage pressure > 140 kPa). With modular resistors, we show independent control of the flow rate and flow switching period of the oscillator system in a wide range (2.5 s–6.4 h and 2 μL/min–2 mL/min). This modular approach can be used to enhance the flexibility of instruction‐embedded microfluidic circuits in which their operational range is limited.     

A photometric detector based on a blue light-emitting diode

The suitability of blue light-emitting diodes as radiation sources in molecular absorption spectroscopy was evaluated. Electronic as well as spectral considerations are discussed. A transducer based on a blue light-emitting diode and a photodiode is described which yields direct absorbance readings by passing the photocurrent to an integrated circuit logarithmic converter. The performance of this device was tested for commonly used spectrophotometric procedures for Cr, Mn, Zn, Fe and Cl and compared with conventional molecular absorption spectroscopy. Also investigated was the application of the transducer as a detector in flow-injection analysis.     

Heterogeneous ultrathin films fabricated by alternate assembly of exfoliated layered double hydroxides and polyanion

Transparent heterogeneous ultrathin films of exfoliated layered double hydroxide (LDHs) nanosheets, fabricated alternately with polyanion, have been obtained via a layer-by-layer electrostatic self-assembly which yields a series of novel LDH films with potential multifunctionality.     

A chiral, 16-ring channel framework and a layered caesium zincoarsenate

Caesium zinc arsenate frameworks with a large, chiral pore and an expansive interlayer region have been synthesised.     

Graphene oxide reinforced polyamide nanocomposite coated on paper as a novel layered sorbent for microextraction by packed sorbent

ABSTRACT

In this work, a novel layered sorbent for microextraction by packed sorbent (MEPS) was introduced, which has been prepared by coating graphene oxide/polyamide (GO/PA) nanocomposite (NC) onto cellulose paper through solvent exchange method. Scanning electron microscopy (SEM) was applied to investigate the surface characteristic and morphology of PA and GO/PA NC coated on cellulose paper. The prepared MEPS device was used for extraction of organophosphorous pesticides (OPPs) including chlorpyrifos, fenthion, fenithrothion, ethion, edifenphos and phosalone in environmental aqueous samples followed by detection using gas chromatography-flame ionisation detector (GC-FID). Important parameters affecting the MEPS method including pH of sample solution, extraction draw-discard cycles, sorbent layers, desorption solvent volume and desorption draw-eject number were studied and optimised using central composite design (CCD). Based on the method validation, limits of detection (LODs) were in the range of 0.2–1 µg L^?1. The calibration graphs for chlorpyrifos, fenthion and edifenphos are linear in the concentration range of 1 to 500 µg L^?1; for ethion and phosalone are linear in the range of 1–1000 µg L^?1 and for fenithrothion is linear in the range of 3–1000 µg L^?1. The method precision (RSD %) with six replicates determinations was in the range of 3 to 9.4 % and 3.9 to 11.9% for distilled water and spiked river water sample, respectively, at the concentration level of 300 µg L^?1 . The developed method was applied successfully to determine OPP compounds in river, dam and tap water samples; accordingly, the relative recoveries (RR%) were obtained in the range of 77.8 to 113.3%.     

Air stream-mediated vortex agitation of microlitre entities on a fluidic chip

The method presented in this paper uses air flux to induce spiral motion in small-scale (e.g., microlitre) fluid entities in an efficient, technologically convenient manner. The set-up entails a manifold that modulates the air flux and projects it onto a liquid-containing reservoir. The flow behaviour of the liquid phase has been visualized through the dissolution of rhodamine B crystallites and the motion of fluorescent microbeads. In addition, the method proved effective to restoring a suspension of spherical particles upon sedimentation, promoting displacement and capture of the beads within a microfluidic system.     

Single particle analysis using fluidic, optical and electrophoretic force balance in a microfluidic system

A unique microfluidic system is developed which enables the interrogation of a single particle by using multiple force balances from a combination of optical force, hydrodynamic drag force, and electrophoretic force. Two types of polystyrene (PS) particles with almost identical size and refractive index (plain polystyrene (PS) particle - mean diameter: 2.06 μm, refractive index: 1.59; carboxylated polystyrene (PS-COOH) particles - mean diameter: 2.07 μm, refractive index: 1.60), which could not be distinguished by optical chromatography, reveal different electrokinetic behaviors resulting from the difference in their surface charge densities. The PS-COOH particles, despite their higher surface charge density when compared to the PS particles, experience a lower electrophoretic force, regardless of ionic strength. This phenomenon can be understood when the more prominent polarization of the counter ion cloud surrounding the PS-COOH particles is considered. The surface roughness of the carboxylated particles also plays an important role in the observed electrokinetic behavior.     

Investigation of "on water" conditions using a biphasic fluidic platform

Converting the DEAD: A fluidic approach to generate precisely defined water-oil interfaces was used to quantify the influence of the water surface (blue drops) on chemical reactions between quadricyclane or β-pinene and diethyl azodicarboxylate (DEAD). This method allows for easy investigation of the "on water" effect.     

Temperature-controlled electrochemical switch based on layered double hydroxide/poly(N-isopropylacrylamide) ultrathin films fabricated via layer-by-layer assembly

In this paper we report the fabrication of layered double hydroxide (LDH) nanoparticles/poly(N-isopropylacrylamide) (pNIPAM) ultrathin films (UTFs) via the layer-by-layer assembly technique, and their switchable electrocatalytic performance in response to temperature stimuli was demonstrated. X-ray diffraction and UV-vis absorption spectroscopy indicate a periodic layered structure with uniform and regular growth of the (LDH/pNIPAM)(n) UTFs; an interaction based on hydrogen bonding between LDH nanoparticles and pNIPAM was confirmed by X-ray-photoelectron spectroscopy and Fourier transform infrared spectroscopy. Temperature-triggered cyclic voltammetry and electrochemical impedance spectroscopy switch for the UTFs was obtained between 20 and 40 °C, accompanied by reversible changes in surface topography and film thickness revealed by atomic force microscopy and ellipsometry, respectively. The electrochemical on-off property of the temperature-controlled (LDH/pNIPAM)(n) UTFs originates from the contraction-expansion configuration of pNIPAM with low-high electrochemical impedance. In addition, a switchable electrocatalytic behavior of the (LDH/pNIPAM)(n) UTFs toward the oxidation of glucose was observed, resulting from the temperature-controlled charge transfer rate. Therefore, this work provides a facile approach for the design and fabrication of a well-ordered command interface with a temperature-sensitive property, which can be potentially applied in electrochemical sensors and switching.     

Single-molecule tracing on a fluidic microchip for quantitative detection of low-abundance nucleic acids

Here, we report a method capable of quantitative detection of low-abundance DNA/RNA molecules by incorporating confocal fluorescence spectroscopy, molecular beacons, and a molecular-confinement microfluidic reactor. By using a combination of ac and dc fields via a trio of 3-D electrodes in the microreactor, we are able to precisely direct the transport of individual molecules to a minuscule laser-focused detection volume ( approximately 1 fL). A burst of fluorescence photons is detected whenever a molecular beacon-target hybrid flows through the detection region, and the amount of targets can be directly quantified according to the number of recorded single-molecule flow-through events. This assay consumes only attomoles of molecular probes and is able to quantitatively detect subpicomolar DNA targets. A measurement time of less than 2 min is sufficient to complete the detection.     

A two bead immunoassay in a micro fluidic device using a flat laser intensity profile for illumination

Recently it was demonstrated that a collimated Gaussian beam can be converted to a flattop beam using a Keplerian beam reshaper consisting of two aspheric lenses. Here, using the same optical system, we demonstrate that this flattop profile can be maintained when used in a confocal detection system that focuses the laser beam into a diameter of only 33 microm. The intensity profile of the reshaped beam was determined by imaging the excitation of a constant stream of fluorescein inside a microfluidic device. The resulting shape had a 6.38% RSD intensity across the flat profile when imaged with a CCD camera. This flat illumination profile was then used in a two bead multiplex immunoassay where the colour combination and/or the intensities can be used to determine the presence of an antigen. Detection limits of TNF-alpha and IL-6 were comparable with standard ELISA immunoassays.     

Effect of gate length and dielectric thickness on ion and fluid transport in a fluidic nanochannel

We have simulated the effect of gate length and dielectric thickness on ion and fluid transport in a fluidic nanochannel with negative surface charge on its walls. A short gate is unable to induce significant cation enrichment in the nanochannel and ion current is controlled mostly by cation depletion at positive gate potentials. The cation enrichment increases with increasing gate length and/or decreasing dielectric thickness due to higher changes induced in the surface charge density and zeta-potential. Thus, long gates and thin dielectric layers are more effective in controlling ion current. The model without Navier-Stokes equations is unable to correctly predict phenomena such as cation enrichment, increase in channel conductivity, and decreasing electric field. Body force and induced fluid velocity decrease slowly and then rapidly with gate potentials. The effectiveness of ion current control by a gate reduces with increasing surface charge density due to reduced fractional change in zeta-potential.     

Integrated fluidic systems on a nanometer scale and the study on behavior of liquids in small confinement

Nanofluidic systems and the studies on the behavior of liquids confined in nanometer-sized space are reviewed. Miniaturized chemical systems having nanometer-sized structures are fabricated by using advanced nanofabrication techniques. The size-confinement effect is expected to be applied in well-controlled chemical and biochemical analysis. While electroosmosis and electrokinetic migration in small-sized channels have been investigated extensively, there have been few reports on pressure-driven flow systems having nanometer-sized structures, which are widely used in laboratory-scale and micrometer-sized systems. In this review, fundamental technologies that can be used in integrated chemical analysis systems having nanometer-sized structures are introduced. In addition to the technological investigations, important topics in the fundamental research on the properties of liquids confined in nanometer-sized space are also presented.     

Swelling, intercalation, and exfoliation behavior of layered ruthenate derived from layered potassium ruthenate

The intercalation chemistry of a layered protonic ruthenate, H_0.2RuO_2.1·nH₂O, derived from a layered potassium ruthenate was studied in detail. Three phases with different hydration states were isolated, H_0.2RuO_2.1·nH₂O (n=0, 0.5, 0.9), and its reactivity with tetrabutylammonium ions (TBA⁺) was considered. The layered protonic ruthenate mono-hydrate readily reacted with TBA⁺, affording direct intercalation of bulky tetrabutylammonium ions into the interlayer gallery. Fine-tuning the reaction conditions allowed exfoliation of the layered ruthenate into elementary nanosheets and thereby a simplified one-step exfoliation was achieved. Microscopic observation by atomic force microscopy and transmission electron microscopy clearly showed the formation of unilamellar sheets with very high two-dimensional anisotropy, a thickness of only 1.3±0.1 nm. The nanosheets were characterized by two-dimensional crystallites with the oblique cell of a=0.5610(8) nm, b=0.5121(6) nm and γ=109.4(2)° on the basis of in-plane diffraction analysis.     

Preparation and characterization of a new layered double hydroxide, Co-Zr-Si

The layered double hydroxides (LDHs) are nano-ordered layered compounds and well known for their ability to intercalate anionic compounds. Most LDH is prepared conventionally only with divalent and trivalent cations. In this study, Co-Zr-Si LDH, consisting of divalent, tetravalent, and tetravalent cations, was prepared and reacted with monocarboxylic acids at room temperature. The Co-Zr-Si LDH and intercalated compounds have been characterized by energy-dispersive X-ray spectrometry, X-ray powder diffraction, IR spectra, thermal analysis, and scanning electron microscopy (SEM). The insertion of cyanate and carbonate anions into LDH was confirmed by IR spectra. XRD patterns of the prepared Co-Zr-Si LDH showed that the interlayer spacing of the LDH is 0.78 nm. The spacing is similar to that of usual LDH in which chloride, carbonate, or bromide anion is the guest. SEM images showed that Co-Zr-Si LDH can exist as plate-like or fibrous structures.     

Syntheses, characterizations and crystal structures of two new lead(II) amino and carboxylate-sulfonates with a layered and a pillared layered structure

Reactions of lead(II) acetate with m-aminobenzenesulfonic acid (HL¹) and 5-sulfoisophthalic acid (H₃L²) afforded two new lead(II) sulfonates, Pb(L¹)₂1 and Pb₂(L²)(μ₃-OH)(H₂O) 2. In compound 1, the lead(II) ion is eight-coordinated by two sulfonate groups bidentately, two sulfonate groups unidentately and two amino groups from six ligands. Each L¹ ligand is tetradentate and bridges with three Pb(II) ions. The interconnection of the Pb(II) ions via bridging sulfonate ligands resulted in 〈100〉 and 〈200〉 layers. In compound 2, one Pb(II) ion is six-coordinated by a carboxylate group bidentately, by two carboxylate groups unidentately, by a sulfonate oxygen atom and by an OH anion, whereas the other one is six-coordinated by a bidentate chelating carboxylate group, two μ₃-OH anions, a sulfonate oxygen atom and an aqua ligand. The interconnection of irregular PbO₆ polyhedra via carboxylate-sulfonate ligands resulted in the formation of a pillared layered structure with the 2D layer being formed; the lead(II) ions, hydroxyl groups, carboxylate and sulfonate groups and the benzene ring as the pillar agent.     

An extrusion fluidic driving method for continuous-flow polymerase chain reaction on a microfluidic chip

A novel extrusion driving protocol was developed based on micro-fabricated polydimethylsiloxane (PDMS) pneumatic valves. High efficiency liquid transfer was performed by using entirely overlapping control channels and fluid channels. A 0.5-s time is sufficient for the transfer of 9 μL sample solution between two chambers in the microchip with a nitrogen pressure of 70 kPa. The driving method was used in a microfluidic polymerase chain reaction (PCR) system, and rapid cycling of the PCR mixture in a closed loop was achieved. The amplification of DNA was demonstrated via both three-stage and two-stage PCR thermal cycling on the microchips resulting in significant reduction of the PCR time. The amplifications of 144-bp and 200-bp DNA fragments were achieved within 24 min using a three-stage protocol with 30 thermal cycles, and 130-bp DNA fragments within 12 min by using 20 thermal cycles in the two-stage system, compared to about 2 h in benchtop PCR with the same number of thermal cycles.