Ultraviolet irradiation and polarographic adsorptive complex wave techniques for the simple and rapid simultaneous determination of trace amounts of zinc,lead and copper in human hair

Polarographic adsorptive complex waves in the presence of catechol violet were studied for the simple and rapid simultaneous determination of traces of zinc, lead and copper in human hair and UV irradiation techniques were compared with conventional acid digestion procedures. UV irradiation of acidified hair with a 500-W mercury are lamp releases bound zinc, lead and copper after 3 h. Compared with the acid digestion procedure, the blank of the UV irradiation method is lower, the amounts of reagents used are smaller and the sample manipulations are simpler. The mechanisms of the polarographic adsorptive complex waves of Zn-, Pb-Cu- catechol violet are discussed.     

Simultaneous Determination of Cadmium,Copper, Lead and Zinc in Amino Acid Parenteral Nutrition Solutions by Anodic Stripping Voltammetry and Sample Digestion by UV Irradiation

Abstract

Irradiation with ultraviolet (UV) energy was investigated to assay cadmium, copper, lead, and zinc by anodic stripping voltammetry (ASV) in amino acid parenteral nutrition (PN) solutions. Sample digestion by UV irradiation showed the best performances to liberate the metals from the samples (metal recoveries between 90% and 102%) in comparison with classical oxidative wet digestion methods. The best UV digestion condition was obtained with 1:10 diluted PN samples irradiated during 10 h at 90±3°C with the addition of one aliquot of 50 µL concentrated H₂SO₄ and repeated additions of 50 µL 30% (v/v) H₂O₂ at each 60 min irradiation interval. By using the UV digestion procedure cadmium, copper, lead, and zinc were simultaneously assayed in commercial amino acid PN solutions by ASV. The metal concentrations ranged between 1.3 to 4.4 for cadmium, 2.9 to 40.8 for copper, 4.4 to 16.8 for lead, and 1.4 to 208.5 for zinc. The ASV method correlated well with atomic absorption spectrometry measurements to assay the investigated analytes in amino acid PN samples after the UV digestion.     

Investigations of oxidative UV photolysis

Summary Oxidative UV photolysis according to DIN standard 38406 E 16 [1] has been investigated as a sample preparation method for voltammetry. UV photolysis has decisive advantages compared with mineral acid digestion owing to the simple procedure and the very low blank values, which in turn are due to the minimal reagent addition required. For UV photolysis with a high pressure mercury lamp, an apparatus has been used that employs a new type of sample cooling and that allows the simultaneous irradiation of 12 samples. The sample preparation for the voltammetric determination of zinc, cadmium, lead, copper, nickel and cobalt has been optimized using a model water solution and subsequently tested with real matrices. The type of organic matrix and the irradiation temperature determine the irradiation time required. To digest aromatic compounds, it is advantageous to work at reaction temperatures of ca. 90°C. The application of UV photolysis centers on water samples slightly polluted with organic compounds; however, it can also be used with more heavily polluted wastewaters. As the digestion times are at most 60 min, the method is of interest for routine analysis.     

Determination of zinc, cadmium, lead and copper in soils and sewage sludges by microprocessor-controlled voltammetry in comparison with atomic absorption spectrometry

Summary Information on the heavy metal contents in soils and sewage sludges is of strong ecological interest. For control of the maximum allowed concentrations photometric and atomic absorption spectrometric methods have been developed for the determination of the single elements; sample digestion is carried out using hydrochloric acid and nitric acid.Differential pulse polarography and differential pulse anodic stripping voltammetry allow the simultaneous determination of different heavy metals in one digestion solution according to their electrochemical behaviour. This possibility is given, for instance, for zinc, cadmium, lead and copper. The adequate procedure was tested with a microprocessor-controlled polarograph. Flame atomic absorption spectrometry was used as reference method.

---

Bestimmung von Zink, Cadmium, Blei und Kupfer in Böden und Klärschlämmen durch mikroprozessorgesteuerte Voltammetrie im Vergleich mit der Atomabsorptionsspektrometrie

     

Determination of metals in lubricating oils by X-ray fluorescence spectrometry

The determination of common wear metals, namely iron, chromium, copper, zinc and lead, in a wide range of lubricating oil samples was investigated for the use of a low-cost, wavelength-dispersive X-ray fluorescence spectrometer. The procedure provided results in satisfactory agreement with inductively coupled plasma spectrometry used as reference method after microwave digestion of the samples in concentrated nitric acid. Statistical tests following extensive regression analyses of the data indicated that interelement effects were not statistically significant and that a simple linear regression was adequate for the calibration of individual metals.     

Determination of trace amounts of copper and zinc in sea water with polymer-supported 1,4,8,11-tetraazacyclotetradecane

The very low affinity of tetraaza macrocycles for alkali and alkaline earth metals make them attractive for the preconcentration of transition metals from seawater. Three different procedures for determinations of copper and zinc with 1,4,8,11-tetraazacyclotetradecane (cyclam) bound to poly(chloromethyl)vinylbenzene are described. Results for both metals in estuarine and oceanic waters, compared to those obtained with Chelex-100 resin, show that the polymer-supported cyclam provides > 95% extraction of these two metals. The resin is used as a solid sample for electrothermal atomic absorption spectrometry, or the metal is back-extracted with nitric acid for injection.     

电感耦合等离子体光谱法测定铜冶炼烟尘中锌

本实验介绍了电感耦合等离子体光谱法测定铜冶炼烟尘中锌含量的分析方法。针对样品碳,硅含量高的特点,有针对性的研究了样品的消解方法,确定采用盐酸、硝酸、氢氟酸、高氯酸对铜冶炼烟尘样品进行消解。同时进行了干扰试验,确定样品中高含量的铜,铅,砷等对样品测定结果没有影响。并对仪器的工作参数进行了优化。方法检出限为为0.011 mg/L,测定下限为0.019 mg/L,3个样品的相对标准偏差在0.54%~0.92%之间,加标回收率在96%~101.14%之间。该方法样品消解完全,流程短,操作简单,快速,测定准确度高,可以满足铜冶炼烟尘中锌含量的测定。     

Cation-exchange separation of metals in dimethyl sulphoxide-aqueous hydrochloric acid media

The behaviour of bismuth, cadmium, copper, lead, silver, tin and zinc on a cation-exchange resin in a solvent system consisting of dimethyl sulphoxide, hydrochloric acid and water was studied. The distribution coefficients of these metal ions between liquid and resin were determined as functions of the concentration of dimethyl sulphoxide and of hydrochloric acid. On the basis of the distribution coefficients found, predictions were made as to the possibilities of separating these metals from mixtures. Such separations were confirmed experimentally for bismuth from lead, bismuth from copper, zinc from lead, lead from cadmium, silver from copper, silver from lead, lead from cadmium from zinc, bismuth from lead from zinc, and bismuth from zinc from copper.     

Determination of Trace Metals in Fish Tissue by Flame Atomic Absorption Spectrometry using a Discreet Nebulization Technique

Abstract

Flame atomic absorption spectrometry is applied to the analysis of trace metals in fish tissue after digestion of the sample with nitric acid in a decomposition vessel. The digested sample is analyzed directly using a discreet nebulization technique. Enhancement effects were observed for all elements studied. The method was applied to the analysis of copper, iron and zinc in several species of fish.     

微波消解-电感耦合等离子体原子发射光谱(ICP-AES)法测定含铜污泥中多种重金属

为了填补现有方法的技术空白,本方法采用微波消解和电感耦合等离子体原子发射光谱法（ ICP-AES）相结合,实现对含铜污泥中铅、锌、铬、镉、砷、镁、铝、锑量的同时测定。首先采用盐酸-硝酸-氢氟酸微波消解进行样品的前处理,消解后加入高氯酸置于电热板进行除碳并赶酸,溶样效果理想,且有效避免了高温溶样对易挥发元素砷、锑的损失,整个过程安全、高效、无损。溶样后以电感耦合等离子体发射光谱法（ ICP-AES）进行测定。对含铜污泥的分解方法进行了合理选择,并对测定时的元素分析谱线及各测定元素间干扰情况等进行了讨论。该方法的加标回收率在95.31%~107.28%%,相对标准偏差（RSD）在0.31%~2.05%之间（n=7),结果表明,该方法准确度高,操作简单快捷,可同时测定多种元素,能满足批量的测定含铜污泥中铅、锌、镍、铁、镉、铬、砷、锑含量的测定要求。     

微波消解-ICP-MS测定电镀污泥中的重金属

采用微波消解系统对某电镀污泥进行消解,利用ICP-MS对污泥中的重金属进行测定。称取制备后样品,置于消解罐中充分反应后,赶酸、定容后利用电感耦合等离子体质谱法进行测定。电镀污泥中的铬为18845.2mg/kg、镉为10.3mg/kg、镍为5200.0mg/kg、铅为189.7mg/kg、铜为3271.7mg/kg、锌为49632.6mg/kg。测定结果表明所检测项目工作曲线线性关系好,相关系数r均大于0.999。铬加标回收率在91.6～97.7%之间、镉加标回收率在92.0～97.0%之间、镍加标回收率在95.1～98.0%之间、铅加标回收率在94.3～95.2%之间、铜加标回收率在97.1～102%之间、锌加标回收率在96.3～98.7%之间,均满足相关测定要求。计算的潜在生态危害系数、潜在生态危害指数结果表明,电镀污泥中的铬、镉、铅、铜、锌为轻微生态危害,镍为强生态危害;潜在生态危害指数RI计算值为216.69,属于中等生态危害。     

The determination of some toxic metals in human liver as a guide to normal levels in New Zealand. Part I. Determination of Bi, Cd, Cr, Co, Cu, Pb, Mn, Ni, Ag, T1 and Zn.

Procedures are described for the determination of bismuth, cadmium, chromium, cobalt, copper, lead, manganese, nickel, silver, thallium and zinc in post-mortem liver samples by atomic absorption spectrometry. The technique involves a simple HCl/HNO₃ digestion at 100 ±20 °C, gives good recoveries and appears to be applicable to other tissues, and blood. Results of analyses of post-mortem material from eleven subjects with no known exposure to toxic metals, are presented. They are comparable with overseas findings and show no excessive levels.     

Speciation of heavy metals in sewage sludge after mesophilic and thermophilic anaerobic digestion

Two types of sewage sludge anaerobic digestion were carried out: mesophilic and thermophilic. Metal speciation analysis was performed revealing some changes in the chemical form of the metals during the stabilization process of sludge. After both methane fermentation processes, a comparable level of organic matter distribution was obtained (≈ 40 %). The amount of produced methane during thermophilic and mesophilic digestion was 560 mL of CH4 and 580 mL of CH₄ from 1 g of removed organic matter, respectively. Low concentration of heavy metal ions in the liquid phase of sludge was observed. Metal ions precipitated and remained bound throughout the stabilization process. No accumulation of heavy metals in the mobile fractions of sludge (exchangeable and carbonate) was observed for either digestion process. The highest increase of zinc, copper, nickel, cadmium, and chromium concentration was observed in the organic-sulfide fraction, whereas the highest increase of lead was found in the residual fraction.     

Probenvorbehandlungsstudien mit biologischen und Umweltmaterialien

Summary The efficiency of wet digestion with nitric acid at 320 °C by use of the high pressure asher published by Knapp [10] has been studied with a series of biological materials which usually are only incompletely decomposed by pressure digestion at 170 °C in PTFE vessels. For that purpose the residual carbon content of the digestion solution was determined by coulometry after combustion in an oxygen stream. The results verify a complete sample digestion already after digestion times of less than 3 h. By the example of bovine liver it is shown that the inverse voltammetric determination of zinc, cadmium, lead and copper is feasible without any subsequent oxidation by perchloric acid and is free of interferences.

---

---

Part IV: (1984) Fresenius Z Anal Chem 317:248     

Preconcentration of trace metals in natural waters with 2,2′-dipyridyl-4-amino-3-hydrazino-5-mercapto-1,2,4-triazolehydrazone supported on silica gel

The new hydrazone, supported on silica gel, is used to preconcentrate traces of copper, zinc, lead, nickel, cobalt and cadmium from tap, lake and sea water. Conditions for quantitative retention are established. Copper, zinc, lead, cadmium and nickel are quantitatively eluted with 0.1 M EDTA, and cobalt with 2 M perchloric acid. The metals are measured by atomic absorption spectrometry.     

Atomic-absorption spectrometric determination of catalytic components (Pd,Ti, and Cu) in mixtures based on phenol

Procedures for the determination of palladium, titanium, and copper in organic reaction mixtures based on phenol were developed with the use of atomic absorption spectrometry and various sample preparation techniques: quantitative back extraction of the metals with a 2 M HCl solution; autoclave digestion in an acid mixture of HClO₄, HF, and HNO₃; and decomposition in a muffle furnace. The accuracy of analysis was demonstrated by a comparison between the results of the atomic-absorption spectrometric determination of the elements obtained with the use of all of the sample preparation techniques proposed and the standard addition method. The relative standard deviation in the determination of palladium, copper, and titanium was 7–10%.     

Determination of copper, lead and cadmium in whole blood by stripping voltammetry with the use of graphite electrodes

The problem with toxic metal ion determination in blood is the adsorption of organic compounds on the electrode surface and the formation of complexes between metal ions and organic constituents of blood. This is the reason why usually preliminary acid digestion or other sample pretreatment is used. Two kinds of electrodes have been used: “Ultra-Trace Electrode”, made from impregnated graphite (I), and thick film graphite disposable electrodes (II). The analysis of whole blood with different sample preparation methods shows, that chemical digestion is not necessary for the analysis. Electrochemical two-stage sample preparation provides the possibility for analysing whole blood with the mentioned electrodes. Thick film disposable electrodes are less sensitive to the interference of organic constituents of blood. These electrodes give the possibility to determine total cadmium, lead and copper concentration in whole blood without special sample pretreatment. The application of “Ultra-Trace Electrode” for blood analysis is possible only after preliminary pretreatment of blood by chemical digestion or electrochemical sample preparation.     

Heavy metal determination in aquatic species for food purposes

New analytical procedures and sample mineralizations are proposed regarding the determination of arsenic, selenium, copper, lead, cadmium, zinc and mercury in matrices involved in food chain as mussel, clams and fishes. As regard As, Se, Cu, Pb, Cd and Zn determinations, H2SO4-HNO3 acidic mixture is used for the digestion of each matrix. In the case of Hg the sample digestion is performed using a concentrated suprapure H2SO4-K2Cr2O7 mixture and the results are compared with those from other conventional methods. Differential pulse cathodic (DPCSV) and anodic stripping voltammetry (DPASV) are employed for determining simultaneously selenium, arsenic and copper, lead, cadmium, zinc, respectively, while mercury determination is carried out by the cold vapour atomic absorption spectrometry (CV-AAS) with reduction with SnCl2. The voltammetric measurements were performed using a conventional three-electrode cell and the ammonia-ammonium chloride buffer (pH 9.3) as supporting electrolyte. For all the elements, in addition to the detection limits, precision and accuracy data are also reported: the former, expressed as relative standard deviation (Sr), and the latter, expressed as relative error (e), are in all cases between 3 to 6%.     

Heavy metals in human urinary calculi

Summary Heavy metals are incorporated in human urinary calculi during a complex pathological process. The trace metals cadmium, lead, chromium, nickel and mercury are determined with regard to significance in pathogenesis and therapy. The amounts of cadmium, lead and chromium were determined as well directly in the solid sample as after chemical digestion by Zeeman-GFAAS. Both analyzing techniques show corresponding results. Nickel could be determined after chemical digestion only, while mercury was determined by a solid sampling technique. The evaluation of the results of trace metal analysis in the pilot study of 11 urinary calculi showed increased amounts of lead and cadmium compared to the results of tartar and salivary calculi.