Carbon Paste Electrode Incorporating 1‐[4‐(Ferrocenyl Ethynyl) Phenyl]‐1‐Ethanone for Electrocatalytic and Voltammetric Determination of Tryptophan

A carbon paste electrode spiked with 1‐[4‐ferrocenyl ethynyl) phenyl]‐1‐ethanone (4FEPE) was constructed by incorporation of 4FEPE in graphite powder‐paraffin oil matrix. It has been shown by direct current cyclic voltammetry and double step chronoamperometry that this electrode can catalyze the oxidation of tryptophan (Trp) in aqueous buffered solution. It has been found that under optimum condition (pH 7.00), the oxidation of Trp at the surface of such an electrode occurs at a potential about 200 mV less positive than at an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α and rate constant for the chemical reaction between Trp and redox sites in 4FEPE modified carbon paste electrode (4FEPEMCPE) were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of Trp showed a linear dependent on the Trp concentrations and linear calibration curves were obtained in the ranges of 6.00×10^?6 M–3.35×10^?3 M and 8.50×10^?7 M–6.34×10^?5 M of Trp concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 1.80×10^?6 M and 5.60×10^?7 M by CV and DPV methods. This method was also examined as a selective, simple and precise new method for voltammetric determination of tryptophan in real sample.     

Electrochemical behavior and determination of L-tryptophan on carbon ionic liquid electrode

A carbon ionic liquid electrode (CILE) was fabricated by mixing N-butylpyridinium hexafluoro-phosphate (BPPF ₆ ) with graphite powder and further used for the investigation on the electrochemical behavior of L-tryptophan (Trp). The fabricated CILE showed good conductivity, inherent electrocatalytic ability and strong promotion to the electron transfer of Trp. On the CILE, an irreversible oxidation peak appeared at 0.948 V (vs. saturated calomel reference electrode). For 5.0 × 10⁻⁵ M Trp the oxidation peak current increased about 5 times and the oxidation peak potential decreased on 0.092 V compared to carbon paste electrode. The results indicated that an electrocatalytic reaction occurred on CILE. The conditions for the electrochemical detection were optimized and the electrochemical parameters of Trp on CILE were carefully investigated. Under the selected conditions, the oxidation peak current showed linear relationship with Trp concentration in the range of 8.0 × 10⁻⁶ ∼1.0 × 10⁻³ M for cyclic voltammetry and the detection limit was estimated as 4.8 × 10⁻⁶ M (3σ). The interferences of other amino acids or metal ions on the determination were tested and the proposed method was successfully applied to the synthetic sample analysis.     

Electrocatalytic Behavior and Amperometric Detection of Morphine on ITO Electrode Modified with Directly Electrodeposited Gold Nanoparticles

A gold nanoparticles (AuNPs) modified indium tin oxide (ITO) film coated glass electrode was prepared via a novel electrochemical deposition technique. The UV‐visible spectrum and SEM indicated that the AuNPs on ITO electrode surface were spherical shape and quite symmetric distributed. The modified electrode exhibited excellent catalytic activity for the oxidation of morphine (MO). At optimal experimental condition, the oxidation current was responsive with the MO concentrations ranging from 8.0×10^?7 to 1.6×10^?5 M, the detection limit was 2.1×10 ^–7 M. The modified electrode also exhibited high stability and reproducibility. The average recoveries of detection MO in human urine were ranged between 91.95% and 92.23%, and the RSD was less than 3.68% (n=5).     

Direct Oxidation of Ascorbic Acid at an Edge Plane Pyrolytic Graphite Electrode: A Comparison of the Electroanalytical Response with Other Carbon Electrodes

The direct electrochemical oxidation of ascorbic acid at an edge plane pyrolytic graphite electrode (EPPG) is investigated and compared with other common carbon‐based electrodes, specifically glassy carbon, boron doped diamond and basal plane pyrolytic graphite. It is found that the EPPG electrode shows a significantly higher degree of electrochemical reversibility than the other electrode substrates giving rise to an analytically optimized limit of detection and sensitivity of 7.1×10^?5 M and 0.065 A M^?1 respectively.     

Enhanced Anodic Electrochemiluminescence of Dissolved Oxygen with 2‐(Dibutylamino) ethanol at TiO2 Nanoparticles Modified Platinum Electrode for Dopamine Detection

The anodic electrochemiluminescence (ECL) of dissolved oxygen with 2‐(dibutylamino) ethanol (DBAE) on platinum electrode has been reported previously by our group. Interestingly, the ECL intensity can be greatly amplified at TiO₂ nanoparticles modified platinum electrode (TiO₂/Pt), which is due to the catalytic effect of TiO₂ nanoparticles to electrochemical oxidation of DBAE. It is the first case to obtain the enhanced ECL from luminophor by electrochemical catalysis of co‐reactant. The enhanced anodic ECL intensity can be quenched by dopamine sensitively. And the ECL intensity versus the logarithm of concentration of dopamine was linear over the 4.0×10^?12–1.8×10^?8 M (R²=0.9957), with the limit of detection of 2.7×10^?12 M (S/N=3).     

Determination of captopril in pharmaceutical forms by stripping voltammetry

A voltammetric procedure is developed for determining captopril in pharmaceuticals. It is based on the preliminary electrochemical accumulation of the captopril oxidation product on a platinum electrode in a 0.1 M HNO₃ solution at 1.2 V versus a saturated silver-silver chloride electrode. The reduction current of the oxidation product is a linear function of captopril concentration in the range from 1.2 × 10^?6 to 3.2 × 10^?4 M. The determination limit is 9.2 × 10^?7 M. The relative standard deviation is between 1 and 4%.     

Electrocatalytic Oxidation and Voltammetric Determination of Hydrazine on the Tetrabromo‐p‐Benzoquinone Modified Carbon Paste Electrode

The electrochemical properties of hydrazine studied at the surface of a carbon paste electrode spiked with p‐bromanil (tetrabromo‐p‐benzoquinone) using cyclic voltammetry (CV), double potential‐step chronoamperometry and differential pulse voltammetry (DPV) in aqueous media. The results show this quinone derivative modified carbon paste electrode, can catalyze the hydrazine oxidation in an aqueous buffered solution. It has been found that under the optimum conditions (pH 10.00), the oxidation of hydrazine at the surface of this carbon paste modified electrode occurs at a potential of about 550 mV less positive than that of a bar carbon paste electrode. The electrocatalytic oxidation peak current of hydrazine showed a linear dependent on the hydrazine concentrations and linear analytical curves were obtained in the ranges of 6.00×10^?5 M–8.00×10^?3 M and 7.00×10^?6 M–8.00×10^?4 M of hydrazine concentration with CV and differential pulse voltammetry (DPV) methods, respectively. The detection limits (3σ) were determined as 3.6×10^?5 M and 5.2×10^?6 M by CV and DPV methods. This method was also used for the determination of hydrazine in the real sample (waste water of the Mazandaran wood and paper factory) by standard addition method.     

Electrochemically Treated Pencil Graphite Electrodes Prepared in One Step for the Electrochemical Determination of Paracetamol

This article reports the electrochemical determination of paracetamol (PC) in the presence of ascorbic acid (AA) and caffeine (CF) using an electrochemically treated pencil graphite electrode. In this study, we describe the use of an electrode prepared by overoxidation between 0.0 and +2.1 V for paracetamol determination. The electrochemically treated pencil graphite electrodes (ETPGEs) were prepared using a cyclic voltammetric method. The electrode was characterized by Scanning Electron Microscopy (SEM), Electrochemical Impedance Spectroscopy (EIS), and Resonance Raman Spectroscopy. The differences in oxidation peak potentials were large enough to determine PC in the presence of AA and CF. The electroactive areas of the bare electrode and 10 scan-ETPGE in 0.5 M H₂SO₄ were calculated to be 0.0031 and 0.0341 cm², respectively. The sensor (10 scan-ETPGE in 0.5 M H₂SO₄) was sensitive to the PC with 1.74 × 10^–7 M limits of detection (S/N = 3). Finally, the developed method and the prepared electrodes were used for determination of PC in the pharmaceutical samples.

     

Thin-layer differential pulse voltammetric determination of chlorpromazine in biological fluids

The combination of a thin-layer electrochemical cell with differential pulse voltammetry can be used to determine chlorpromazine in plasma and urine. The thin-layer cell (23 μl capacity) has a wax-impregnated graphite electrode. Direct determination of chlorpromazine in urine gave a linear calibration curve for the range 4.8 × 10^-3–2.4 × 10^-4 M with 97% recovery. No interference from glutethimide, dextropropoxyphene, meprobamate, diazepam, and methaqualone-HCl was detected. Direct measurement of chlorpromazine in plasma gave a linear calibration curve for the range 2.4 × 10^-5–4.8 × 10^-4 M with 89% recovery. The procedure for plasma and urine requires only 2 min per determination. Detection levels are below that required for monitoring therapeutic levels of chlorpromazine in urine.     

The Quantitative Detection of Phenylephrine in Pharmaceutical Preparations and Spiked Human Urine by Voltammetry

A voltammetric method was used for the quantitative detection of phenylephrine in pharmaceutical preparations and spiked human urine. The electrochemical measurements were carried out in various buffer solutions in the pH range from 0.51 to 12.00 on ultra-trace graphite electrode (UTGE) by cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques. The dependence of pH on the oxidation peak current and peak potential was investigated. Britton–Robinson buffer (pH 8.02) was selected for analytical purposes. The peak was established to be diffusion controlled nature of electrode. A linear calibration curve for DPV analysis was constructed in the phenylephrine concentration range from 8 × 10^–6 to 1 × 10^–4 M. Limits of detection (LOD) and quantification (LOQ) were obtained as 2.07 × 10^–7 M and 6.91 × 10^–6 M respectively. The repeatability, accuracy and precision of the developed technique were checked in spiked urine and pharmaceutical preparations.     

Electrocatalytic performance of cobalt microparticles film-modified platinum disk electrode for amperometric detection of ascorbic acid

Deposited cobalt microparticales (Co-MPs) film onto the platinum disk electrode has been successfully used as a new amperometric sensor for the determination of ascorbic acid (AA). AA is detected by surface catalyzed oxidation involving cobalt(III) oxyhydroxides in alkaline solution. The Co-MPs/Pt electrode exhibits a high electrocatalytic activity toward the AA oxidation. The diffusion coefficient of AA (6.09 × 10⁵ cm²/s) and the catalytic rate constant (k _cat = 6.27 × 10³ M^–1s^–1) have been determined using electrochemical approaches. The amperometric response of the modified electrode is linear against the AA concentration in the range (0.01?0.48 mM). The sensor displays the best activity with a high response signal, a good sensitivity of 74.3 μA/mM, a low detection limit of 2.5 μM (signal/noise = 3) and a fast response time (<3 s). Moreover, the reproducibility, selectivity and applicability of this biosensor are satisfactorily evaluated.     

Catalytic Oxidation of Dopamine at a Nickel Hexacyanoferrate Surface Modified Graphite Wax Composite Electrode Coated with Nafion

A chemically modified electrode was successfully fabricated by means of depositing a thin layer of nickel hexacyanoferrate (NiHCF) on an amine adsorbed graphite paraffin wax composite electrode using a new approach. The electrode was further coated with Nafion. The electrochemical characteristics of the modified electrode were studied using cyclic voltammetry and electrochemical impedance spectroscopy (EIS). The modified electrode catalyzed dopamine (DA) oxidation in the concentration range of 1.5×10^?6 to 1.2×10^?3 M without the interference from ascorbic acid (AA). A detection limit of 4.9×10^?7 M was obtained for DA in the presence of AA with a correlation coefficient of 0.9972 based on S/N=3. Flow injection analysis was used for the determination of dopamine with excellent reproducible results. The analytical utility of the sensor was evaluated for detection of DA in urine.     

Electrochemical Behavior and Determination of Rutin at the Copper Nanoparticles-Doped Zeolite A/Graphene Oxide-Modified Electrode

In this work, a novel Cu?zeolite A/graphene modified glassy carbon electrode was applied for the determination of rutin. The Cu?zeolite A/graphene composites were prepared using copper doped zeolite A and graphene oxide as the precursor, subsequently reduced by chemical agents. Based on the Cu?zeolite A/graphene modified electrode, the overpotential of the rutin oxidation was lowered by ~300 mV. Also the proposed Cu?zeolite A/graphene modified electrode showed higher electrocatalytic performance than zeolite A/graphene electrode or graphene modified electrode. The electrochemical behavior of copper incorporated in the zeolite A modified electrode illustrated the adsorption-controlled reaction at the modified electrode. The behavior of electrocatalytic oxidation of rutin at the modified electrode was investigated. The diffusion coefficient of rutin was equal to 4.2 × 10^–7 cm²/s. A linear calibration graph was obtained for rutin over the concentration range of 2.3 × 10^–7–2.5 × 10^–3 M. The detection limit for rutin was 1.2 × 10^–7 M. The RSDs of 10 replicate measurements performed on a single electrode at rutin concentrations between 2.3 × 10^–7–2.5 × 10^–3 M were between 1.1 and 2.1%. Study of the influence of potentially interfering substances on the peak current of rutin showed that the method was highly selective. The proposed electrode was used for the determination of rutin in real samples with satisfactory results.     

Electrocatalysis and Voltammetric Determination of Dopamine at a Calix[4]arene Crown‐4 Ether Modified Glassy Carbon Electrode

A sensitive and selective electrochemical method for the determination of dopamine (DA) was developed using a calix[4]arene crown‐4 ether (CACE) film modified glassy carbon electrode (GCE).The modified electrode exhibited good electrocatalytic activity for electrochemical oxidation of DA in the pH 6.00 Britton–Robinson buffer solution, and ascorbic acid (AA) did not interfere with it. The diffusion coefficient (D=2.7×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient (α=0.54) of DA at the surface of CACE were determined using electrochemical approaches. The catalytic oxidation peak currents showed a linear dependence on the DA concentration and a linear analytical curve was obtained in the range of 2.0×10^?5–1.0×10^?3 M of DA with a correlation coefficient of 0.9990. The detection limit (S/N=3) was estimated to be 3.4×10^?6 M. This method was also examined for the determination of DA in an injection sample. In addition, effects of possible interferences were investigated. The present work shows the potential of the proposed method for the fabrication of a modified electrode, as it can be effectively used for voltammetric detection of DA.     

Enhanced Oxidation of Simvastatin at a Multi‐Walled Carbon Nanotubes‐Dihexadecyl Hydrogen Phosphate Composite Modified Glassy Carbon Electrode and the Application in Determining Simvastatin in Pharmaceutical Dosage Forms

A sensitive electrochemical method for the determination of simvastatin (SV) was established, based on the enhanced oxidation of SV at a multi‐walled carbon nanotubes‐dihexadecyl hydrogen phosphate composite modified glassy carbon electrode (MWNTs‐DHP/GCE). The voltammetric studies showed that MWNTs instead of DHP or GCE could effectively catalyze the oxidation of SV. The dependence of oxidation current on SV concentration was explored under optimal conditions, which exhibited a good linear relationship in the range of 1.0×10^?7–7.5×10^?6 M. The detection limit of SV was also examined and a low value of 5.0×10^?8 M was obtained for 5 min accumulation (σ=3). This electrode was applied to the detection of SV in drug forms and the results were in accordance with those obtained by UV spectroscopy.     

Electrochemical conversions of pentaphenyl(methoxycarbonyl)cyclopentadiene derivatives

Redox processes of fluctuating pentaphenyl(methoxycarbonyl)cyclopentadiene derivatives on platinum electrode in acetonitrile are studied by cyclic voltammetry. The reduction of derivatives of pentaphenylcyclopentadiene C₅Ph₅M yields a radical anion which decomposes to anion M^- and stable radical C₅Ph ₅ ^• ; the latter reduces to C₅Ph₅. In the first stage of oxidation of these compounds, a stable radical cation forms, with substituent M intact. Reduction of derivatives of pentamethoxycarbonylcyclopentadiene [C₅(CO_2Me)₅]M yields a dianion. Such electrochemical behavior of fluctuating cyclopentadiene compounds reveals additional information on the mechanism of displacement of the element-centered substituents M in them     

Electrochemical Oxidation of Nortriptyline and Its Voltammetric Sensing at a Carbon Ionic Liquid Electrode

The electrochemical oxidation of nortriptyline at a carbon ionic liquid electrode (CILE) was investigated. Nortriptyline is electrochemically inactive on conventional electrodes but CILE exhibited excellent electrocatalytic activity toward oxidation of nortriptyline with the well-defined anodic peak at 860 mV. This characteristic was attributed to the outstanding conductivity and electrocatalytic effect of the ionic liquid, 1-octylpyridinum hexaflourophosphate, used as a binder in the construction of the electrode. The influence of experimental parameters such as pH and sweep rate was also studied. The quantitative determination of nortriptyline was performed using differential pulse voltammetry technique. Under selected conditions the anodic peak current was linear to nortriptyline concentration in the ranges of 4.8 × 10^–6 to 2.4 × 10^–5 M and 2.4 × 10^–5 to 6.4 × 10^–5 M, with correlation coefficients of 0.9992 and 09949, respectively. The detection limit was 3 × 10^–7 M.     

Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

L‐Cysteine Voltammetry at a Carbon Paste Electrode Bulk‐Modified with Ferrocenedicarboxylic Acid

The electrochemical behavior of L ‐cysteine studied at the surface of ferrocenedicarboxylic acid modified carbon paste electrode (FDCMCPE) in aqueous media using cyclic voltammetry, differential pulse voltammetry and double potential step chronoamperometry. It has been found that under optimum condition (pH 8.00) in cyclic voltammetry, the oxidation of L ‐cysteine occurs at a potential about 200 mV less positive than that of an unmodified carbon paste electrode. The kinetic parameters such as electron transfer coefficient, α, and catalytic reaction rate constant, k_h were also determined using electrochemical approaches. The electrocatalytic oxidation peak current of L ‐cysteine showed a linear dependent on the L ‐cysteine concentration and linear analytical curves were obtained in the ranges of 3.0×10^?5 M–2.2×10^?3 M and 1.5×10^?5 M–3.2×10^?3 M of L ‐cysteine concentration with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods respectively. The detection limits (3σ) were determined as 2.6×10^?5 M and 1.4×10^?6 M by CV and DPV methods.     

Detection of Uric Acid in the Presence of Dopamine and High Concentration of Ascorbic Acid Using PDDA Modified Graphite Electrode

The properties of graphite electrode (Gr) modified with poly(diallyl dimethyl ammonium chloride) (PDDA) for the detection of uric acid (UA) in the presence of dopamine (DA) and high concentration of ascorbic acid (AA) have been investigated by cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The polymer modified graphite electrode was prepared by a very simple method just by immersing the graphite electrode in PDDA solution for 20 minutes. The PDDA/Gr modified electrode displayed excellent electrocatalytic activity towards the oxidation of UA, DA and AA compared to that at the bare graphite electrode. The electrochemical oxidation signals of UA, DA and AA are well resolved into three distinct peaks with peak potential separations of 220 mV, 168 mV and 387 mV between AA‐DA, DA‐UA and AA‐UA respectively in cyclic voltammetry studies and the corresponding peak potential separations are 230 mV, 130 mV and 354 mV respectively in differential pulse voltammetry. The lowest detection limits obtained for UA, DA and AA were 1×10^?7 M, 2×10^?7 M and 800×10^?9 M respectively. The PDDA/Gr electrode efficiently eliminated the interference of DA and a high concentration of AA in the determination of UA with good selectivity, sensitivity and reproducibility. The modified electrode was also successfully applied for simultaneous determination of UA, DA and AA in their ternary mixture.