Volumetric emission of argon plasmas in the presence of vapors of Fe,Si, and Al

The net volumetric emission was calculated for argon plasmas at atmospheric pressure in the presence of metal vapors for different elements, over the temperature range from 3000 to 30,000 K. The computations are based on the escape factor model, using a semi-empirical method for the determination of line profiles and line broadening effects. Results for iron, .silicon, and aluminum show an important influence of the presence of even the smallest concentrations of the metal vapors on the net emission coefficient of the plasma. The effect is strongest for iron, followed by aluminum and .silicon. Special attention is given to self-absorption effects which are most important in the first millimeter o% the optical path of the emitted radiation. The effect is incorporated into the calculation procedure of the net emission coefficient and can be used as a volumetric energy sink as long as the absorption length is shorter than the radius of the control volume used in the computation scheme.     

Chemical and physical modification and electret properties of polytetrafluoroethylene films

Composites with titanium oxide structures on the surface of a polymer matrix were prepared by preliminary plasma activation of polytetrafluoroethylene films, followed by chemical treatment with vapors of titanium tetrachloride and water. The chemical composition and structure of the modified film surface were studied by scanning electron microscopy, atomic force microscopy, and X-ray photoelectron spectroscopy. The stability of the formed surface charge increases in going from the initial film to the plasma-activated film, then to the film successively treated with vapors of titanium tetrachloride and water, and finally to the plasma-activated film treated subsequently with vapors of titanium tetrachloride and water. The modified polytetrafluoroethylene films are of interest as electrets with enhanced operation characteristics.     

Determination of gallium in an iron-aluminium matrix by solvent extraction and flame emission spectroscopy

Solvent extraction of gallium(III) into methyl isobutyl ketone from hydrochloric acid solutions containing titanium (III) sulphate provides a rapid method for separation of gallium from an iron/aluminium matrix and may be employed to eliminate the interference of these elements in the flame emission spectrometric determination of gallium.     

Spectrophotometric determination of the pH scale in ethane-1,2-diol

A highly selective method is described for the determination of gallium at the ppm-level in manganese nodules and geological reference samples. After dissolution of the sample, gallium is adsorbed on Dowex 1 (chloride form) from hydrochloric acid solution containing titanium trichloride, which reduces iron(III) so that it is not adsorbed. After elution with dilute nitric acid and evaporation, gallium is determined by atomic-absorption spectrometry with an air-acetylene flame.     

Thin-layer chromatography of aluminium: quantitative densitometric determination of Fe2+, Ni2+, Cu2+, and Si4+

Thin-layer chromatography in combination with scanning densitometry is used as a tool for the quantitative determination of some impurity and additive elements in aluminium. Microgram levels of iron, silicon, copper, nickel, titanium, magnesium, manganese, and zinc present in a high concentration aluminium matrix is detected, and selective separations of some of these elements are achieved on silica gel H layers developed with a mobile phase containing aqueous sodium chloride solution. The quantitative determination of iron, silicon, nickel, and copper are obtained from the densitometric evaluation of chromatograms and are compared with the respective optical emission spectral analytical data.     

Organic photoconductors. VIII. Photoconductors obtained from the reaction products of poly(9-vinyl anthracene)

9-Vinyl anthracene has been polymerized by three methods in cationic systems to obtain organic photoconductors. Cationic polymerization catalysts used were titanium tetrachloride and aluminum chloride anhydride. According to the degree of conversion from poly(9-vinyl anthracene) to poly(9,10-dimethylene anthracene) the photosensitivity increased.     

Effect of the presence of iron vapors on the volumetric emission of Ar/Fe and Ar/Fe/HZ plasmas

The net volumetric emission coefficient was calculated using the escape factor method for Ar/Fe and Ar/H₂/Fe plasmas, at atmospheric pressure, over the temperature range from 3000 K to 30,000 K. The calculation involved 712 lines for Ar I, Ar II, and Ar III, 3481 lines for Fe I, Fe II, and Fe III, and 230 lines for H in the Ar/H₂/Fe case. A semiempirical method was used for the determination of line profiles and line broadening. The results show a strong influence of the presence of even traces of iron vapors at low temperatures where the volumetric emission increases by several orders of magnitude. Special attention is given to self-absorption of the argon resonance lines which prevents the radiation from escaping within a few millimeters from the emission source.     

Interaction of titanium tetrachloride vapors with zirconium dioxide nanocrystals

Products of interaction of the surface of zirconium dioxide nanocrystals with titanium tetrachloride as a test reagent were studied. The composition and structure of the surface of synthesized products depending on the time of treating the substrate by titanium chloride vapor were determined by a complex monitoring of both chemical conversions in the gas phase and concentrations of components in the solid-phase matrix with the help of gravimetric “in situ” measurements at various stages of the reaction.     

Determination of chlorinated hydrocarbons introduced into air/acetylene flames by Fourier transform infrared emission spectroscopy

A Fourier transform spectrometer is used to record the infrared emission from chlorinated hydrocarbons combusted in an air/acetylene flame. In this manner, the chlorinated hydrocarbons are determined by monitoring the infrared emission of hydrogen chloride at 2653 cm(-1). Discussion is presented of the air/acetylene flame background, and the potential spectral interference from the emission of deuterated species. Practical detection limits for chloroform, carbon tetrachloride and methylene chloride in acetone, methanol, and ethanol are solvent independent and are found to be 1.1, 0.80, and 1.0%, respectively. Calibration curves for these three analytes are linear from their detection limits to approximately 55% (v/v). In addition, evidence is presented that flame flicker-noise does not lead to a multiplex disadvantage when the Fourier transform instrument is used for data acquisition.     

Adsorption Properties of Silica Gel Prepared from a Decationized Sol

In accordance with the IUPAC classification, the shape of the capillary condensation hysteresis and type of the sorption isotherms of the vapors of water and tetrachloromethane by silica gel are identified, the latter being prepared from a decationized silica sol in the presence of aluminum chloride. It is found that the adsorption and structural properties of the silica gel depend on the concentration of silicon(IV) oxide and Al/Si molar ratio, as well as on the type of the adsorbate used. It is shown that the effect of aluminum chloride is manifested mainly in the spatial rearrangement of the particles of silicon(IV) oxide into dense agglomerates followed by their aggregation with the conservation of internal porosity. This leads to the appearance of narrow slitlike mesopores and to a decrease in or the stabilization of the average pore radius.     

FLAME EMISSION SPECTROMETRIC METHOD FOR NIOBIUM IN STEELS

Abstract

Following the dissolution steps, niobium(V) is extracted into methyl isobutyl ketone in the form of a heptafluoride complex. Stannous chloride is added to the aqueous solution to reduce iron(III) to an unextracted iron(II) species. The organic solution is then aspirated into a fuel-rich acetylene-oxygen flame and the emission intensity measured at 4059 Å. Optimum observation height is slightly above the tip of the blue inner cone. Detection limit is 13 μg/ml. Results are given for two steel samples.     

分光光度法同时测定硅石中的铁和铝

在邻二氮菲(Phen)、铬天青S(CAS)和十四烷基二甲基苄基氯化铵(TDMBA)的共同存在下,于pH 5～6的酸性介质中,铁、铝分别生成Fe-Phen和Al-CAS-TDMBA络合物,用同一份试液,在波长510 nm测定铁,在625 nm测定铝,两种络合物互不干扰。用该法可同时测定硅石中的铁和铝。     

Porous Silica Particles Prepared from Silicon Tetrachloride Using Ultrasonic Spray Method

Silica particles having the median diameter of 1 to 3 μm were prepared from silicon tetrachloride vapor by a reaction with water droplets using the ultrasonic spray method. The particle sizes of silicas were controlled by changing the composition of silicon tetrachloride and water. These silica particles had microporous structures from nitrogen and water adsorption measurements. The microporous and mesoporous particles were prepared from the reaction of water droplets including sodium and potassium carbonates with silicon tetrachloride vapor. Copyright 1999 Academic Press.     

悬浮液直接进样ICP–OES法测定高纯氧化铝中的铁、钛、硅、铬

采用悬浮液直接进样电感耦合等离子体发射光谱法(ICP–OES)测定高纯氢氧化铝中铁、钛、硅、铬的含量。悬浮液用电磁搅拌器搅拌,均匀地分散在溶液中,通过仪器蠕动泵进入雾化室,均匀无阻地导入ICP光源。Fe,Ti,Si,Cr的分析谱线分别为259.940,336.112,251.611,205.552 nm;RF功率为1 300W,等离子体气流量为13.0 L/min,雾化器气体流量为0.60 L/min,辅助气流量为1.00 L/min。Fe,Ti,Si,Cr的质量浓度分别在0.0~30.0,0.0~15.0,0.0~90.0,0.0~15.0μg/m L范围内与信号强度呈良好的线性,线性相关系数均大于0.999,方法的检出限为0.027 6~0.993 9μg/m L,测量结果的相对标准偏差为0.65%~6.84%(n=11),回收率为95.0%~104.8%。该法抗干扰能力强、线性范围宽,适用于高纯氢氧化铝中铁、钛、硅、铬含量的分析。     

Synergistic effect of ferric chloride and silicon mixtures on the thermal stabilization enhancement of ABS

A previous study from this laboratory has shown that Lewis acid-type transition metal chlorides (NiCl₂, CoCl₂, ZnCl₂, and FeCl₃) are effective char forming catalysts for ABS terpolymer in an inert atmosphere [Jang J, Kim JH, Bae JY. Polym Degrad Stab 2005;88(2):324.]. However, transition metal chloride catalysed char formation (and flame-retardance enhancement) of ABS in air was unsuccessful due to the oxidative degradation of the char at a higher temperature. In order to overcome these undesirable phenomena, we incorporated silicon with transition metal chlorides as co-catalyst and a series of ABS/transition metal chloride/silicon compounds were made from them and their flame retardancy was evaluated by measuring the limiting oxygen index (LOI) values. Our results showed that among various transition metal chloride/silicon catalyst systems the incorporated mixture of ferric chloride and silicon is very effective in enhancing the thermal stabilization of ABS and LOI value as high as 33 is obtained. The reason for this synergistic effect by ferric chloride and silicon was postulated to come from the interaction between ferric chloride and silicon at elevated temperatures, probably generating silicon tetrachloride and hydrogen chloride.     

Sur la synthèse de chloro-3 indolinones a partir de β-nitrostyrènes diversement substitués

When treated with acetyl chloride and ferric chloride in methylene chloride, at 0°, monosubstituted β-nitrostyrene derivatives such as 2,3 or 4-methyl, -chloro or -fluoro and 3-nitro-β-nitrostyrenes cyclize into the new corresponding 3-chloro-1,3-dihydro-2H-indol-2-one. Reaction with other metal chlorides such as aluminum chloride and titanium tetrachloride does not lead to these heterocyclic derivatives but only produces N-acetyl-N-hydroxy-α-chlorobenzeneacetamides and/or N-(acetyloxy)-α-chlorobenzeneethanimidoyl chlorides.     

A new class of platinum (II) vapochromic salts

Luminescent chloride and hexaflurophosphate salts of Pt(Me2bzimpy)Cl+ (Me2bzimpy = 2,6-bis(1-methylbenzimidazol-2-yl)pyridine) are reported. As solids, both compounds are vapochromic, undergoing pronounced and reversible changes of color and emission in the presence of volatile organic compounds. The chloride salt responds to vapors of methanol, chloroform, ethanol, and acetonitrile, undergoing a distinct change in color from yellow to red within seconds. The PF6- salt responded selectively to acetonitrile vapor, changing from yellow to violet while sorbing 1.0 +/- 0.1 equiv. For either salt, leaving vapor-exposed samples in air for several days or heating for several minutes restored the original color. UV-visible absorption spectra and solid-state room temperature and 77 K emission spectra are reported, and the accumulated data are consistent with a decrease in Pt...Pt separation accompanying vapor sorption.     

Synthesis and binding activity of 4-azanicotine

4-Azanicotine ( 1 ) has been synthesized by the cyclopropylimine rearrangement. A study of several Lewis acids as possible catalysts for the NMF-mediated cyclopropyl imine rearrangement of cyclopropyl-2-pyrazinylmethanone ( 4 ) indicated that both aluminum chloride and magnesium chloride are suitable catalysts, lithium bromide shows only a trace of activity and zinc chloride, titanium tetrachloride, and titanium tetra-isopropoxide show no activity. Compound 1 , in which the aromatic ring is less basic than in nicotine, and 6-aminonicotine ( 5 ), in which the aromatic ring is more basic, have been compared with the binding properties of nicotine in the P2 rat brain preparation. Compound 1 binds with an affinity very similar to that of nicotine at two of the receptor sites, 5 binds at these sites but with a lower affinity. Unlike nicotine, 1 and 5 do not bind at the very high affinity ‘upregulatory’ site.     

The characteristic of photoluminescence of tris‐(7‐substituted‐8‐hydroxyquinoline) aluminum complexes and polymeric complexes

The 7‐allyl‐ and 7‐(2‐methylvinyl)‐functionalized derivatives of 8‐hydroquinoline are synthesized by Claisen rearrangement and double bond rearrangement respectively. Then 7‐allyl‐8‐hydroquinoline (C) and 7‐(2‐methylvinyl)‐8‐hydroquinoline (D) are reacted with aluminum chloride to afford the corresponding tris‐(7‐allyl‐8‐hydroxyquinoline) aluminum complex (F) and tris‐(7‐(2‐methylvinyl)‐8‐hydroxyquinoline) aluminum complex (G). The photoluminescence of complex (F) or (G), compared with that of tris‐(8‐hydroxyquinoline) aluminum complex (E), all showed a red shift in emission wavelengths in different solvents, such as chloroform, hexane and ethanol. For two substituents containing an external double bond, the 2‐methylvinyl group gives a larger red shift in the emission wavelength than the allyl group. The X‐ray crystal structure indicates that 7‐(2‐methylvinyl)‐8‐hydroxyquinoline (D) is a trans‐isomer. The styrene and 7‐allyl‐8‐hydroxyquinoline copolymer, and the styrene and 7‐(2‐methylvinyl)‐8‐hydroxyquinoline copolymer are also reported. Further reactions of the copolymer are then performed by adding aluminum(III) chloride and ligands 8‐hydroxyquinoline. The spectroscopic characteristics of these aluminum(III) polymeric complexes are discussed. Copyright © 2003 John Wiley & Sons, Ltd.     

Catalytic effects of Fe,Al and Si on the formation of NO<Subscript>X</Subscript> precursors and HCl during straw pyrolysis

The catalytic effects of iron, aluminum or silicon on the formation of NO_X precursors (HCN, NH₃ and HNCO) and HCl during wheat straw pyrolysis were studied using a thermogravimetric analyzer (TG) coupled with a Fourier transform infrared (FTIR) spectrometer in argon atmosphere. The results show that the presence of iron, aluminum or silicon decreases conversion of straw-N into NH₃ with the sequence of Fe > Si > Al. The iron or silicon addition suppresses N-conversion into HCN and HNCO, and the aluminum addition has no notable influence on HCN emission during pyrolysis. The share of N-conversion to NH₃ and HCN increases, but that to HNCO and NO decreases a little in the presence of added iron, aluminum or silicon. The addition of SiO₂ results in the highest HCl removal efficiency.