Polymers as Hydrophobic Adsorbent Surface for Some Surfactants

Polyvinyl alcohol (PVA) and polyacrilic acid (PAA) were used as hydrophobic adsorbent surfaces at 25°C for two nonionic surfactants, namely, tetradecyl polyoxyethylenated monolaurate [La(EO)₁₄] and tetradecyl polyoxyethylenated monooleate [Ol(EO)₁₄], and two anionic surfactants, namely, sodium oleic sulfonate [OlSO₃Na] and sodium dodecyl benzene sulfonate [SDBS]. Surface tension measurements were performed to determine the critical micelle concentration (CMC) and the adsorption isotherms of the tested surfactants. All the tested surfactants display L-shape isotherms except that of OlSO₃Na onto PVA. No adsorption behavior has been shown for the anionic SDBS onto both PVA and PAA. The adsorption data show higher adsorption affinity for all the tested nonionic surfactants onto PAA than onto PVA while the investigated anionic surfactant OlSO₃Na possesses close values of Γ_max. The study reveals that the nature of the polymer surface as adsorbent besides the molecular structure of the surfactant defined the types and mechanisms of adsorption.     

Interaction between polymer and anionic/nonionic surfactants and its mechanism of enhanced oil recovery

Various experimental methods were used to investigate interaction between polymer and anionic/nonionic surfactants and mechanisms of enhanced oil recovery by anionic/nonionic surfactants in the present paper. The complex surfactant molecules are adsorbed in the mixed micelles or aggregates formed by the hydrophobic association of hydrophobic groups of polymers, making the surfactant molecules at oil-water interface reduce and the value of interfacial tension between oil and water increase. A dense spatial network structure is formed by the interaction between the mixed aggregates and hydrophobic groups of the polymer molecular chains, making the hydrodynamic volume of the aggregates and the viscosity of the polymer solution increase. Because of the formation of the mixed adsorption layer at oil and water interface by synergistic effect, ultra-low interfacial tension (～2.0?×?10^?3 mN/m) can be achieved between the novel surfactant system and the oil samples in this paper. Because of hydrophobic interaction, wettability alteration of oil-wet surface was induced by the adsorption of the surfactant system on the solid surface. Moreover, the studied surfactant system had a certain degree of spontaneous emulsification ability (D50?=?25.04?µm) and was well emulsified with crude oil after the mechanical oscillation (D50?=?4.27?µm).     

Anionic–Nonionic Mixed Surfactant Systems: Micellar Interaction and Thermodynamic Behavior

The interactions between an anionic surfactant, viz., sodium dodecylbenzenesulfonate and nonionic surfactants with different secondary ethoxylated chain length, viz., Tergitol 15-S-12, Tergitol 15-S-9, and Tergitol 15-S-7 have been studied in the present article. An attempt has also been made to investigate the effect of ethoxylated chain length on the micellar and the thermodynamic properties of the mixed surfactant systems. The micellar properties like critical micelle concentration (CMC), micellar composition (X_A), interaction parameter (β), and the activity coefficients (f_A and f_NI) have been evaluated using Rubingh's regular solution theory. In addition to micellar studies, thermodynamic parameters like the surface pressure (Π_CMC), surface excess values (Γ_CMC), average area of the monomers at the air–water interface (A_avg), free energy of micellization (ΔG_m), minimum energy at the air–water interface (G_min), etc., have also been calculated. It has been found that in mixtures of anionic and nonionic secondary ethoxylated surfactants, a surfactant containing a smaller ethoxylated chain is favored thermodynamically. Additionally, the adsorption of nonionic species on air/water interface and micelle increases with decreasing secondary ethoxylated chain length. Dynamic light scattering and viscometric studies have also been performed to study the interactions between anionic and nonionic surfactants used.     

Effect of Polymer on Dynamic Interfacial Tensions of Anionic–nonionic Surfactant Solutions

The dynamic interfacial tensions (IFTs) of enhanced oil recovery (EOR) surfactant/polymer systems against n-decane have been investigated using a spinning drop interfacial tensiometer in this paper. Two anionic–nonionic surfactants with different hydrophilic groups, C₈PO₆EO₃S (6-3) and C₈PO₆EO₆S (6-6), were selected as model surfactants. Partially hydrolyzed polyacrylamide (HPAM) and hydrophobically modified polyacrylamide (HMPAM) were employed. The influences of surfactant concentration, temperature, polymer concentration, and oleic acid in the oil on IFTs have been studied. The experimental results show that anionic–nonionic surfactants can form compact adsorption films and reach ultralow IFT (10^?3 mN/m) under optimum conditions. The addition of polymer has great influence on dynamic IFTs between surfactant solutions and n-decane mainly by the formation of looser mixed films resulting from the penetration of polymer chains into the interface. The compact surfactant film will also be weakened by the competitive adsorption of oleic acid, which results in the increase of IFT. Moreover, the penetration of polymer chains will be further destroyed surfactant/polymer mixed layer and lead to the obvious increase of IFT. On the other hand, polymers show little effect on the IFTs of 6-6 systems than those of 6-3 because of the hindrance of longer EO chain of 6-6 at the interface.     

Mixed micellization and surface properties of non-ionic/cationic surfactants

We investigate the surface properties of aqueous binary mixtures of our cationic surfactant O-dodecyl-N,N′-diisopropylisourea hydrochloride (ISO-DIC C₁₂) with commercially available nonionic surfactant polyoxyethylene p-(1,1,3,3-tetramethylbutyl)phenyl ether (TritonX-100) at different temperatures (288 to 303?K). The micellization behavior of the binary systems is studied by determining the surface tension and other important physicochemical parameters, such as the critical micelle concentration (CMC), surface tension at the CMC(γ_cmc), Krafft Temperature (T_K), maximum excess concentration (Γ_max), minimum surface area per molecule (A_min), surface pressure at the CMC (П_cmc), and the adsorption efficiency (pC20) at the air/water interface. The study has additionally covered the calculation of thermodynamic parameters of micellization, including the standard Gibbs free energy, the standard enthalpy, the standard entropy, the free energy, and the Gibbs free energy of adsorption at air/water interface. The CMC values of the binary systems determined by experimental data are used to evaluate the micellar composition in the mixed micelle, the interaction parameter β and the activity coefficients f₁(ISO-DIC C₁₂) and f₂ (polyoxyethylene p-(1,1,3,3-tetramethylbutyl)phenyl ether) using the theoretical treatment proposed by Clint and Rubingh. Our results reveal that the proposed binary systems possess enhanced surface activity compared to those of the individual surfactants.     

Interaction of Nonionic Surfactant Triton-X-100 with Ionic Surfactants

The interaction in two mixtures of a nonionic surfactant Triton-X-100 (TX-100) and different ionic surfactants was investigated. The two mixtures were TX-100/sodium dodecyl sulfate (SDS) and TX-100/cetyltrimethylammonium bromide (CTAB) at molar fraction of TX-100, α_TX-100 = 0.6. The surface properties of the surfactants, critical micelle concentration (CMC), effectiveness of surface tension reduction (γ_CMC), maximum surface excess concentration (Γ_max), and minimum area per molecule at the air/solution interface (A _min) were determined for both individual surfactants and their mixtures. The significant deviations from ideal behavior (attractive interactions) of the nonionic/ionic surfactant mixtures were also determined. Mixtures of both TX-100/SDS and TX-100/CTAB exhibited synergism in surface tension reduction efficiency and mixed micelle formation, but neither exhibited synergism in surface tension reduction effectiveness.     

Electroosmotic Flow of a General Electrolyte Solution through a Fibrous Medium

Although hydrotropy is extensively used in industry, the molecular mechanism of hydrotropic solubilization has not been completely elucidated yet. In this paper the interaction between a nonionic surfactant (ethoxylated fatty alcohol containing between five and six oxyethylenic units) and sodium p-toluene sulfonate is examined. Surface tension measurements confirm that the hydrotropic effect occurs at a concentration in which the hydrotropes self-associate. Photon correlation spectroscopy studies show that for this concentration of hydrotropes a drastic reduction in the surfactant micellar radius occurs. Furthermore the luminescence of the hydrotrope used as a fluorescence probe indicates that at low concentrations p-toluene sulfonate dissolves in the surfactant micelles but beyond the minimum concentration for hydrotropic solubilization the hydrotrope is present in the aqueous phase. These results suggest that the hydrotropic effect is related to alterations in the water structure induced by the hydrotrope molecules and to the presence of hydrotrope aggregates that furnish an appropriate niche for the surfactant amphiphile.     

Salt Effect,Surface, and Aggregation Properties of Binary Surfactant Mixtures of a Nonionic Gemini Surfactant (HBA(EO)80) with Anionic Surfactants

Nonionic gemini surfactants HBA(EO)₈₀ were synthesized and characterized by means of surface tension measurements. CMCs of two mixed system, nonionic gemini mixed with anionic gemini (HBA(EO)₈₀/C11pPHCNa) and nonionic gemini mixed with anionic monomeric (HBA(EO)₈₀/SL) and the effect of salt on the two mixed system were investigated. Freeze-fracture transmission electron microscopy and scanning electron microscopy were used to investigate the mixed aggregates' morphologies. The results show that large spherical aggregates were formed in the mixed solution, which trend to transfer into micelles with the increases of the salt concentration.     

A potentiometric titration study on the dissociation of bile acids related to the mode of interaction between different head groups of nonionic surfactants with free bile salts upon mixed micelle formation in water

By constructing an elaborate set of potentiometric titration together with data analysis system, apparent acid dissociation indices (pK _a ^app ) for two bile acids were determined in the mixed surfactant system of bile salts (Sodium Deoxycholate, NaDC, and Sodium Chenodeoxycholate, NaCDC) with nonionic surfactants (Hexaethyleneglycol monon-dodecylether, C₁₂E₆, Decanoyl-N-methylglucamide, MEGA-10) in aqueous solution at ionic strength 1.5 as a function of mole fraction in the surfactant mixture. It was found that with increasing the bile salt concentration, pK _a ^app as well as pH showed an abrupt rise at a certain concentration of the bile salt being regardable as a critical micellization concentration (CMC) and reached a constant value at the range sufficiently higher than CMC for each pure bile salt system, meaning that the dissociation degree of carboxyl group in micelle is smaller than that in bulk. In the mixed systems of free bile salts with nonionic surfactants, the dissociation state of carboxyl groups in mixed micelles depends on the species of hydrophilic group of nonionic surfactants as well as on mole fraction in the surfactant mixture.     

The effect of polyoxyethylene glycol monoethers ofn-hexadecanol on the stability of a polystyrene latex dispersion

The influence of nonionic surface active agents, a series of polyoxyethylene glycol monoethers ofn-hexadecanol, on the stability of dispersions of 2m diameter polystyrene latices has been investigated.Adsorption and microelectrophoretic studies showed the presence of looped monolayers of surface active agent at plateau adsorption.Examination of sedimentation volumes and redispersibility, correlated with potential energy calculations, showed that the stability of the dispersions depended on the characteristics of the adsorbed layer and on added electrolyte.     

The partition of ethoxylated non-ionic surfactants between two non-miscible phases

The partition of a polydispersed ethoxylated non-ionic surfactant in equilibrated oil–water systems has been studied at 25 °C. The model surfactant used was a commercial sample of nonylphenol ethoxylated with 10 moles of ethylene oxide (NPEO₁₀). The partition isotherms over the range of surfactant concentration including the critical micelle concentration (CMC) were made with n-hexane, i-octane and n-decane as oil phases. Each partition isotherm exhibits a change of slope that matched the CMC value of surfactant determined by surface tension measurements on aqueous solutions. During the partition of NPEO₁₀ in the oil–water systems, the oligomer distribution in the oil and water phases changed because of fractionation. Below CMC, the mean ethoxylation degree in the oil phase was smaller, whereas in water it was higher than the mean initial value of the surfactant. Moreover, the mean ethoxylation degree in both oil and water phase was practically independent of surfactant concentration. Above CMC, the mean distribution of ethoxymers decreased in both phases. This was ascribed to the competition between micelles from water and the oil phase for the more hydrophobic species of the surfactant. The mean distribution of ethoxymers in the aqueous phase asymptoted to a value that was the mean of the surfactant itself, whereas it steeply decreased in the organic phase.     

Synthesis of Some Novel Nonionic Ethoxylated Surfactants Based on α-Amino Acids and Investigation of Their Surface Active Properties

Eight novel ethoxylated nonionic surfactants were prepared based on oil soluble α-amino acids. The L-phenylalanine and L-leucine were esterified and amidated with cetyl alcohol and palamitic acid, respectively; two amides and two esters of α-amino acids were obtained. The ethylene oxide was condensed with the prepared amides and esters to get three different polyethylene oxide units (40, 60, and 100) as phenylalanine derivatives. The amide and ester of α-L-leucine were ethoxylated at (60 ethylene oxides units). The analytical micro analysise, FTIR, ¹H NMR, ¹³C NMR, mass spectra were carried out to confirm the chemical structures. The surface tension of the water soluble prepared compounds was measured at 25°C, further the surface active properties were determined and calculated. Such that critical micelle concentration (CMC), surface excess (Γ_max); area per molecule (A_min), effectiveness (γ_CMC) free energy of micellization and adsorption (ΔG_mic, ΔG_ad). From the data obtained it was found that the CMC of phenylalanine esters is greater than that obtained for the amide derivatives. The Γ_max decreased as the ethylene oxide units (EO) increased. It was found also that the ΔG_ad was greater than the ΔG_mic. The obtained data and discrepancy were discussed on the light of surfactant chemical structure.     

Adsorption kinetics measurements of some nonionic surfactants

Dynamic surface tension values of aqueous surfactant solutions were measured by using the ring and plate method. The mean diffusion coefficients calculated on the basis of the purely diffusion controlled adsorption model vary between 2 · 10^–6 to 7 · 10^–6 cm²/s for all surfactants studied:n-alkanols,n-alkanoic acids, dimethyl and diethyln-alkyl phosphine oxides. That means the surfactants investigated adsorb with a purely diffusion controlled adsorption mechanism and no barriers excist to hinder sorption processes.Nomenclature c ₀ surfactant bulk concentration - D diffusion coefficient - surface concentration - ₀ equilibrium surface concentration - ¯ (t)/ ₀ reduced surface concentration - maximum surface concentration - K ₀/c₀ - surface tension - t time - Dt/K ² reduced time - a _L coefficient of the Langmuir isotherm     

Application of Hydrophobicity Parameters to Prediction of the Acute Aquatic Toxicity of Commercial Surfactant Mixtures

Abstract

Ethoxylated alcohols are the most extensively used nonionic surfactants in detergent products. The application of QSAR to their aquatic toxicity is complicated by the fact that they are multicomponent mixtures, the parent alcohols being often mixtures of isomers and homologues, each one being ethoxylated to varying degrees. A spreadsheet method for calculation of aquatic toxicity of such nonionic surfactant mixtures is presented. The method is based on a combination of the Könemann narcosis QSAR and mixture toxicity equations based on the principle of concentration addition. Log P values used in the spreadsheet calculations are themselves calculated by spreadsheet formulae based on the Leo and Hansch method modified by incorporation of the position dependent branching factor originally applied to linear alkylbenzene sulphonates. Close agreement between calculated and experimental EC50 values (48 hr Daphnia tests) is obtained for a range of ethoxylated alcohols having a diversity of branching patterns, carbon numbers and degrees of ethoxylation. The effects of increasing carbon number (decreasing EC50), branching (increasing EC50) and increasing degree of ethoxylation (increasing EC50) are all quantified.     

Mutual Influence of Some Flavonoids and Classical Nonionic Surfactants on Their Adsorption and Volumetric Properties at Different Temperatures

Due to the increasing practical use of mixtures of flavonoids with nonionic surfactants the presented studies were based on the measurements of surface tension and conductivity of aqueous solution of the quercetin (Q) and rutin (Ru) in the mixtures with Triton X-114 (TX114) and Tween 80 (T80) as well as the contact angle of model liquids on the PTFE surface covered by the quercetin and rutin layers. Based on the obtained results components and parameters of the quercetin and rutin surface tension were determined and the mutual influence of Q and Ru in the mixtures with TX114 and T80 on their adsorption and volumetric properties were considered. It was found, among others, that based on the surface tension isotherms of the aqueous solution of the single flavonoid and nonionic surfactant, the surface tension isotherms of the aqueous solution of their mixture, the composition of the mixed monolayer at the water-air interface as well as the CMC of flavonoid + nonionic surfactant mixture can be predicted. The standard Gibbs energy, enthalpy and entropy of the adsorption and aggregation of the studied mixtures were also found, showing the mechanism of the adsorption and aggregation processes of the flavonoid + nonionic surfactant mixture.     

Mutual interactions between nonionic surfactants and gelatin — investigations in cubic liquid crystalline systems and micellar systems

The mutual interactions between nonionic surfactants such as polyoxyethylene cetyl ethers (C₁₆EO _n ,n=15, 20) especially their cubic lyotropic liquid crystalline phases of typeI ₁ and polymer gelatin were investigated. The colloidal microstructure of such anI ₁-phase consisting of close-packed globular surfactant aggregates was shown by transmission electron microscopy (TEM). The diameter of the globules found by TEM correlated well with the periodic distance of about 7.5 nm obtained by small angle x-ray diffraction (SAXD). In ternary systems consisting of surfactant, gelatin, and water cubic liquid crystalline structures were also proved by polarized light microscopy, TEM, and SAXD. The polymer did not participate in the cubic structure but formed, at least in part, anisotropic spherulites. In diluted surfactant systems however, interactions between polymer and surfactants were clearly found by polarimetry. The nonionic surfactants caused an accelerated coil-helix transition of the polypeptid gelatin.     

Role of the Surfactant Structure in the Behavior of Hydrophobic Ionic Liquids within Aqueous Micellar Solutions

The behavior of an ionic liquid (IL) within aqueous micellar solutions is governed by its unique property to act as both an electrolyte and a cosolvent. The influence of the surfactant structure on the properties of aqueous micellar solutions of zwitterionic SB‐12, nonionic Brij‐35 and TX‐100, and anionic sodium dodecyl sulfate (SDS) in the presence of the “hydrophobic” IL 1‐butyl‐3‐methylimidazolium hexafluorophosphate ([bmim][PF₆]) is assessed along with the possibility of forming oil‐in‐water microemulsions in which the IL acts as the “oil” phase. The solubility of [bmim][PF₆] within aqueous micellar solutions increases with increasing surfactant concentration. In contrast to anionic SDS, the zwitterionic and nonionic surfactant solutions solubilize more [bmim][PF₆] at higher concentrations and the average aggregate size remains almost unchanged. The formation of IL‐in‐water microemulsions when the concentration of [bmim][PF₆] is above its aqueous solubility is suggested for nonionic Brij‐35 and TX‐100 aqueous surfactant solutions.     

Adsorption kinetics of nonionic surfactants using the drop volume method

The kinetic results obtained for the nonionic surfactantsn-octyl,n-decyl, andn-dodecyl dimethyl andn-octyl, andn-decyl diethyl phosphine oxide show purely diffusion controlled adsorption. The drop volume technique applied in a static and dynamic version proves to be useful to measure the adsorption kinetics in the form of surface tensions in function of time. Comparisons of the results obtained from both the static and the dynamic measuring procedure confirm the validity of a theory applied to interpret the kinetic data.Nomenclature a Langmuir parameter - c ₀ surfactant bulk concentration - D diffusion coefficient - surface concentration - ₀ equilibrium surface concentration - ¯ (t)/ ₀ reduced surface concentration - maximum value of - R gas law constant - surface tension - ₀ surface tension of pure water - t time - T absolute temperature     

Aggregation behavior and adsorption properties of salt-free catanionic surfactant mixtures containing tetradecyltrimethyl ammonium salts

The aggregation behavior of salt-free catanionic surfactants, tetradecyltrimethyl ammonium hydroxide (TTAOH)/fatty acid (FA) including octanoic acid (OA), decylic acid (DA) and lauric acid (LA) in aqueous solutions were studied. The critical micelle concentration(cmc), surface tension at cmc (γ_cmc), surface excess (Г_max), mean molecular surface area (A_min), adsorption efficiency (pc₂₀) and surface tension reduction effectiveness (π_cmc) were obtained from surface tension isotherms. The influence of temperature on the surface tension of salt-free TTAOH/FA (TTAOF) systems was investigated. Data of adsorption dynamics indicated that at fixed adsorption time, the order of adsorption capacity was TTAOH?相似文献