Optimum phase-behavior formulation of surfactant/oil/water systems for the determination of chromium in heavy crude oil and in bitumen-in-water emulsion

An “oil in water” formulation was optimized to determine chromium in heavy crude oil (HCO) and bitumen-in-water emulsion (Orimulsion-400®) samples by transversally heated electrothermal atomic absorption spectrometry (TH-ET AAS) using Zeeman effect background correction. The optimum proportion of the oil-water mixture ratio was 7:3 v/v (70 ml of oil as the internal phase) with a non-ionic surfactant concentration (Intan-100) in the emulsion of 0.2% w/w. Chromium was determined in different crude oil samples after dilution of the emulsions 1:9 v/v with a 0.2% w/w solution of surfactant in order to further reduce the viscosity from 100 to 1.6 cP and at the same time to bring the concentration of chromium within the working range of the ET AAS technique. The calibration graph was linear from 1.7 to 100 μg Cr l⁻¹. The sensitivity was of 0.0069 s l μg⁻¹, the characteristic mass (m_o) was of 5.7 pg per 0.0044 s and the detection limit (3σ) was of 0.52 μg l⁻¹. The relative standard deviation of the method, evaluated by replicate analyses of three crude oil samples varied in all cases between 1.5 and 2.6%. Recovery studies were performed on four Venezuelan crude oils, and the average chromium recovery values varied between 95.9-104.8, 90.6-107.6, 95.6-104.0 and 98.8-103.9% for the Cerro Negro, Crudo Hamaca and Boscán crude oils and for the Orimulsión®-400, respectively. The results obtained in this work for the Cerro Negro, Crudo Hamaca and Boscán crude oils and for the Orimulsión®-400 following the proposed procedure were of 0.448±0.008, 0.338±0.004 0.524±0.021 and 0.174±0.008 mg Cr l⁻¹, respectively, which were in good agreement with the values obtained by a tedious recommended standard procedure (respectively: 0.470±0.05, 0.335±0.080, 0.570±0.021 and 0.173±0.009 mg Cr l⁻¹).     

The distribution of dissolved thallium in the different water masses of the western sector of the Ross Sea (Antarctica) during the austral summer

Vertical profiles for total dissolved thallium were obtained at five sites in the western sector of the Ross Sea (Southern Ocean), Antarctica. Thallium is estimated to have a natural mean seawater concentration between 50 and 65 pmol L^{− 1} with higher values in the North Pacific (65 ± 5 pmol L^{− 1}) and lower in the Bay of Biscay and Irish Sea (49 ± 3 pmol L^{− 1}). Our samples show a concentration varying from 22 to 55 pmol L^{− 1} with a mean value of 46 pmol L^{− 1}, depending on depth, dissolved oxygen, salinity and local topographic characteristics. The analyses were performed using an ICP-SFMS that has enabled us to obtain reliable Tl concentration measurements with a relative standard deviation of better than 2.5% and a detection limit, calculated as three times the standard deviation of the “blank signal” of 0.69 pmol L^{− 1} (1.60 pmol L^{− 1}, obtained analysing four blank solutions (n = 5) prepared with the same water and acid used for the dilution/acidification steps). Thallium appears to have a nearly conservative distribution in seawater as highlighted also from the comparison with the profiles of two seawater conservative elements: molybdenum and uranium; however it also highlights the presence of a reactive component of thallium, which is more influenced by the presence of particulate matter, oxygen content and fluorescence.     

High-throughput quantification of palladium in water samples by ion pair based-surfactant assisted microextraction

A novel method for the determination of palladium as a metal ion model was developed by ion pair based surfactant-assisted microextraction (IP-SAME) and inductively coupled plasma-optical detection (ICP-OES). In this methodology, a cationic surfactant was used in extraction process. It has two fundamental functions: (1) the formation of an emulsified phase and (2) the ion pair formation with Pd(II) in the presence of iodide ions and making PdI₄²⁻$\text{Pd}{{\text{I}}_4}^{2-}$ extractable into organic phase (active microextraction). The effective parameters on the extraction recovery such as the types of extraction solvent and the surfactant, surfactant concentration, KI amount and HCl concentration of the sample were investigated and optimized. In the proposed approach, tetradecyl trimethyl ammonium bromide (TTAB) was used as emulsifier and ion pairing agent, and 1-octanol was selected as extraction solvent. Under the optimum conditions, the enhancement factor as large as 146 was obtained. The detection limit for palladium was 0.2 μg L⁻¹, and the relative standard deviation (RSD) was 4.1% (n = 5, C = 10.0 μg L⁻¹). The proposed method was applied for extraction and determination of palladium in different water samples.     

Species selective preconcentration and quantification of gold nanoparticles using cloud point extraction and electrothermal atomic absorption spectrometry

The determination of metallic nanoparticles in environmental samples requires sample pretreatment that ideally combines pre-concentration and species selectivity. With cloud point extraction (CPE) using the surfactant Triton X-114 we present a simple and cost effective separation technique that meets both criteria. Effective separation of ionic gold species and Au nanoparticles (Au-NPs) is achieved by using sodium thiosulphate as a complexing agent. The extraction efficiency for Au-NP ranged from 1.01 ± 0.06 (particle size 2 nm) to 0.52 ± 0.16 (particle size 150 nm). An enrichment factor of 80 and a low limit of detection of 5 ng L⁻¹ is achieved using electrothermal atomic absorption spectrometry (ET-AAS) for quantification. TEM measurements showed that the particle size is not affected by the CPE process. Natural organic matter (NOM) is tolerated up to a concentration of 10 mg L⁻¹. The precision of the method expressed as the standard deviation of 12 replicates at an Au-NP concentration of 100 ng L⁻¹ is 9.5%. A relation between particle concentration and the extraction efficiency was not observed. Spiking experiments showed a recovery higher than 91% for environmental water samples.     

Novel Oil‐in‐Water Emulsions Stabilised by Ionic Surfactant and Similarly Charged Nanoparticles at Very Low Concentrations

Novel oil‐in‐water (O/W) emulsions are prepared which are stabilised by a cationic surfactant in combination with similarly charged alumina nanoparticles at concentrations as low as 10^?5 m and 10^?4 wt %, respectively. The surfactant molecules adsorb at the oil‐water interface to reduce the interfacial tension and endow droplets with charge ensuring electrical repulsion between them, whereas the charged particles are dispersed in the aqueous films between droplets retaining thick lamellae, reducing water drainage and hindering flocculation and coalescence of droplets. This stabilization mechanism is universal as it occurs with different oils (alkanes, aromatic hydrocarbons and triglycerides) and in mixtures of anionic surfactant and negatively charged nanoparticles. Further, such emulsions can be switched between stable and unstable by addition of an equimolar amount of oppositely charged surfactant which forms ion pairs with the original surfactant destroying the repulsion between droplets.     

Spectrophtometric determination of malachite green in fish farming water samples after cloud point extraction using nonionic surfactant Triton X-100

A novel and sensitive cloud point extraction procedure for the determination of trace amounts of malachite green by spectrophotometry was developed. Malachite green was extracted at pH 2.5 mediated by micelles of nonionic surfactant Triton X-100. The extracted surfactant-rich phase was diluted with ethanol and its absorbance was measured at 630 nm. The effect of different variables such as pH, Triton X-100 concentration, cloud point temperature and time and diverse ions was investigated and optimum conditions were established. The calibration graph was linear in the range of 4-500 ng mL⁻¹ of malachite green in the initial solution with r = 0.9996 (n = 10). Detection limit based on three times the standard deviation of the blank (3S_b) was 1.2 ng mL⁻¹ and the relative standard deviation (R.S.D.) for 20 and 300 ng mL⁻¹ of malachite green was 1.48 and 1.13% (n = 8), respectively. The method was applied to the determination of malachite green in different fish farming and river water samples.     

Speciation of chromium in river water samples contaminated with leather effluents by flame atomic absorption spectrometry after separation/preconcentration by cloud point extraction

In the present work, a cloud point extraction (CPE) system has been proposed for determination of species de chromium in the natural water samples, Cr(III) and Cr(VI). The procedure was based on the reaction of Cr(III) with 1-(2-pyridilazo)-2-naphtol (PAN) in a surfactant solution (Triton X-114) yielding a hydrophobic complex, which then is entrapped “in situ” in the surfactant micelles. When the temperature of the system was higher than the cloud point of Triton X-114, the complex of Cr(III)-PAN entered the surfactant-rich phase and thus separation of the analyte from the matrix was achieved. Separation of the two phases was accomplished by centrifugation for 15 min at 2500 rpm. The Cr(VI) assay is based on its reduction to Cr(III) by ascorbic acid which subsequently reacts with PAN in a similar manner. The main factors affecting the cloud point extraction, such as complexation pH (7.7), buffer concentration (0.025 mol L^{− 1}) and microwave irradiation time (10 min) were optimized by response surface methodology (RSM) using Box–Behnken design. Under the optimized conditions, the preconcentration system (50 mL sample) permitted an enrichment factor of 48, linear range of 2.5–80 μg L^{− 1}, limit of detection and quantification of 0.7 and 2.5 μg L^{− 1}, respectively, and the relative standard deviation (n = 10) of 2.0% for 50 μg L^{− 1} Cr(III) solution and (n = 10) 5.5% for 10 μg L^{− 1}. The proposed procedure was applied to the speciation of chromium in river water samples. The procedure affords recoveries of 84–115% and a relative standard deviation lower than 4.2%. The analytical results of total chromium in the river water samples under study agreed well with those by electrothermal atomic absorption spectrometry (ET AAS). It is proved that the procedure can be successfully employed as an alternative to the commonly used preconcentration and speciation analytical techniques.     

On-line liquid-liquid extraction system using a new phase separator for flame atomic absorption spectrometric determination of ultra-trace cadmium in natural waters

A robust flow injection (FI) on-line liquid-liquid extraction (LLE) preconcentration/separation system associated with a newly designed gravitational phase separator, coupled to flame atomic absorption spectrometry (FAAS) was developed. The performance of the system was illustrated for cadmium determination at the μg l⁻¹ level. The non-charged cadmium complex with ammonium pyrrolidine dithiocarbamate (APDC) was extracted on-line into isobutyl methyl ketone (IBMK). The organic phase was effectively separated from a large volume of aqueous phase and is led into a 100 μl loop of an injection valve before its introduction into the nebulizer. The system was optimized and offered good performance characteristics with unlimited life time of phase separator, greater flow rate ratios and improved flexibility, as compared with other solvent extraction preconcentration systems. With a sampling frequency of 33 h⁻¹, the enhancement factor was 155, the detection limit was 0.02 μg l⁻¹, the relative standard deviation was 3.2% at 2.0 μg l⁻¹ Cd concentration level and the calibration curve was linear over the concentration range 0.06-6.0 μg l⁻¹. The accuracy of the proposed method was evaluated by analyzing a certified reference material of water and by recovery measurements on spiked samples. Finally, it was successfully applied to the analysis of tapwater, river and seawater samples.     

Micelle-mediated cloud point extraction and spectrophotometric determination of rhodamine B using Triton X-100

A new micelle-mediated cloud point extraction method is described for sensitive and selective determination of trace amounts of rhodamine B by spectrophotometry. The method is based on the cloud point extraction of rhodamine B from aqueous solution using Triton X-100 in acidic media. The extracted surfactant rich phase is diluted with water and its absorbance is measured at 563 nm by a spectophotometer. The effects of different operating parameters such as concentration of surfactant and salt, temperature and pH on the cloud point extraction of rhodamine B were studied in details and a set of optimum conditions were obtained. Under optimum conditions a linear calibration graph in the range of 5-550 ng mL⁻¹ of rhodamine B in the initial solution with r = 0.9991 (n = 15) was obtained. Detection limit based on three times the standard deviation of the blank (3S_b) was 1.3 ng mL⁻¹ (n = 10) and the relative standard deviation (R.S.D.) for 50 and 350 ng mL⁻¹ of rhodamine B was 2.40 and 0.87% (n = 10), respectively. The method was applied for the determination of rhodamine B in soft pastel, hand washing liquid soap, matches tip and textile dyes mixture samples.     

Simultaneous cloud point extraction and spectrophotometric determination of carmoisine and brilliant blue FCF in food samples

A novel simultaneous cloud point extraction method for the determination of carmoisine and brilliant blue FCF by spectrophotometry has been developed. The method is based on the cloud point extraction of carmoisine and brilliant blue FCF from aqueous solution using Triton X-100, diluting the extracted surfactant rich phase with water and measuring the absorbance at 522 and 640 nm for carmoisine and brilliant blue FCF, respectively. The effects of different parameters such as pH, concentration of surfactant and temperature on the cloud point extraction of both dyes were investigated and optimum conditions were established. Linear calibration curves were obtained in the range of 0.02-3.50 μg mL⁻¹ for carmoisine and 0.05-3.50 μg mL⁻¹ for brilliant blue FCF under optimum conditions. Detection limit based on three times the standard deviation of the blank (3S_b) was 0.017 and 0.016 μg mL⁻¹ (n = 10) for carmoisine and brilliant blue FCF, respectively. The relative standard deviation (RSD) for 0.1 μg mL⁻¹ was 4.14 and 3.30% (n = 10), for carmoisine and brilliant blue FCF, respectively. The method was applied to the simultaneous determination of the dyes in different food samples.     

An environmentally friendly multicommutated alternative to the reference method for anionic surfactant determination in water

It has been developed a fully mechanized procedure for the spectrophotometric determination of anionic surfactants in water expressed in terms of SDS concentration. The reference method, based on the reaction of SDS with methylene blue (MB) followed by extraction in chloroform, was mechanized in order to reduce the consumption of organic solvents. The system was based on the multicommutation approach and provided a 35 times reduction of the waste production without sacrificing the figures of merit of the method in terms of sensitivity and repeatability, for a dynamic linear range from 0.2 to 1.7 mg l⁻¹. Results obtained for washing water samples were comparable with those obtained using the reference method and no significant differences, at 95% confidence level, were observed. Other useful characteristics are a solvent consumption of 0.7 ml per determination, a sampling throughput of 40 determinations per hour, a relative standard deviation of 5.9% (n = 10) for a sample containing 2 × 10⁻⁶ mol l⁻¹ (576 μg l⁻¹) surfactant and a limit of detection of 6.1 × 10⁻⁹ mol l⁻¹ (1.7 μg l⁻¹).     

Study of beta-cyclodextrin/fluorinated trimethyl ammonium bromide surfactant inclusion complex by fluorinated surfactant ion selective electrode

The construction and performance of a liquid membrane electrode responsive to N-(1,1,2,2-tetrahydroperfluorooctyl)-N,N,N-trimethylammonium bromide (FTABr) and its use for the study of β-cyclodextrin/fluorinated surfactant inclusion complex is described. The electrode is based on the use of tetrahydroperfluorooctyltrimethylammonium-tetraphenylborate ion pair as electro active material in polyvinyl chloride (PVC) matrix plasticized using 2-Nitrophenyl octyl ether (NPOE). The electrode exhibits a fast, stable, reproducible and “Nernstian” response (59 ± 2 mV) for FTABr over the concentration range of 10⁻⁵ to 2 × 10⁻³ mol L⁻¹ at 298 K. The lowest detection limit is 2 × 10⁻⁶ mol L⁻¹ and the response time is around 20-30 s. The validity of the electrode, for detection of fluorinated surfactant ions and hence to carry out electrochemical measurements to study micellization of fluorinated surfactant, is verified by comparing the critical micelle concentration (cmc) value of FTABr obtained by using the electrode, with that obtained by surface tension measurements. Association constant K for β-cyclodextrin/FTABr complex is evaluated from the potentiometric measurements carried out using this electrode and is observed to be ∼1.26 × 10⁵. The results suggest that β-cyclodextrin forms an equimolar association complex with the FTA⁺ surfactant ion.     

Trace lead measurement and on-line removal of matrix interference in seawater by isotope dilution coupled with flow injection and ICP-MS

Isotope dilution analysis method coupled with flow injection and inductively coupled plasma mass spectrometry (ID-FI-ICP-MS), enabled trace lead concentration in seawater to be determined and the high salt concentration in the matrix, such as Na⁺, Ca²⁺ and Mg²⁺, to be removed on-line. The operational parameters of the FI system including pH for the chelating reaction, concentration of 8-hydroxyquinoline-5-sulfonic acid (8-HQS), sample loading time and injection speed, washing time and speed, eluting acid concentration and eluting speed, and instrumental parameters for ICP-MS were optimized and selected. Accurate results could be achieved because the isotope ratios required can be precisely measured in the range of the eluting peak by means of ID-FI-ICP-MS. The 3σ detection limit was 0.204 ng ml⁻¹. The trace lead concentration of seawater in south Xiamen, China was 0.988 ± 0.039 ng ml⁻¹. The recoveries of spiked Pb standard in seawater and standard reference water (GBW 08607) were 97.9 and 101.0%, respectively, with a relative standard deviation of 0.98%. This method can be used to determine trace lead concentration in high salt matrix samples, and is especially useful when the eluting peaks do not have a Gaussian-distribution.     

Separation and preconcentration of trace amounts of aluminum ions in surface water samples using different analytical techniques

A separation/preconcentration of aluminum (III) (Al³⁺) has been developed to overcome the problem of high matrix species, which may interfere with the determination of trace quantity of Al³⁺ in natural water samples. The separation of Al³⁺ in water samples was carried out from interfering cations by complexing them with 2-methyle 8-hyroxyquinoline (quinaldine) on activated silica. Whereas the separated trace amounts of Al³⁺ was preconcentrated by cloud point extraction (CPE), as prior step to its determination by spectrofluorimetry (SPF) and flame atomic absorption spectrometry (FAAS). The Al³⁺ react with 8-hydroxyquinoline (oxine) and then entrapped in non-ionic surfactant Triton X-114. The main factors affecting CPE efficiency, such as pH of sample solution, concentration of oxine and Triton X-114, equilibration temperature and time period for shaking were investigated in detail. The validity of separation/preconcentration of Al³⁺ was checked by certified reference material of water (SRM-1643e). After optimization of the complexation and extraction conditions, a preconcentration factor of 20 was obtained for Al³⁺ in 10 mL of natural water samples. The relative standard deviation for 6 replicates containing 100 μg L⁻¹ of Al³⁺ was 5.41 and 4.53% for SPF and FAAS, respectively. The proposed method has been applied for determination of trace amount of Al³⁺ in natural water samples with satisfactory results.     

A novel fiber optic spectrophotometric determination of nitrite using Safranin O and cloud point extraction

A novel fiber optic spectrophotometric method for nitrite determination in different samples is suggested, based on the reaction of nitrite with Safranin O in acidic medium to form a diazo-safranin, which is subsequently coupled with pyrogallol in alkaline medium to form a highly stable, red azo dye, followed by cloud point extraction (CPE) using a mixed micelle of a nonionic surfactant, Triton X-114, with an anionic surfactant, sodium dodecyl sulphate (SDS). The reaction and extraction conditions (e.g., acidity for diazotization and alkalinity for pyrogallol coupling, and other reagent concentrations, time, and tolerance to other ions) were optimized. Linearity was obeyed in a concentration range up to 230 μg L⁻¹, and the detection limit of the method is 0.5 μg L⁻¹ of nitrite ion. The molar absorptivity for nitrite of the Safranin-diazonium salt (?_610 nm = 4 × 10³ L mol⁻¹ cm⁻¹) existing in literature was greatly enhanced by pyrogallol coupling and CPE enrichment (?_592 nm = 1.39 × 10⁵ L mol⁻¹ cm⁻¹). The method was applied to the determination of nitrite in tap water, lake water and milk samples with an optimal preconcentration factor of 20.     

Voltammetric determination of isoprenaline in pharmaceutical preparations using a copper(II) hexacyanoferrate(III) modified carbon paste electrode

The electroanalytical determination of isoprenaline in pharmaceutical preparations of a homemade carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) was studied by cyclic voltammetry. Several parameters were studied for the optimization of the sensor such as electrode composition, electrolytic solution, pH effect, potential scan rate and interferences in potential. The optimum conditions were found in an electrode composition (in mass) of 15% CuHCF, 60% graphite and 25% mineral oil in 0.5 mol l⁻¹ acetate buffer solution at pH 6.0. The analytical curve for isoprenaline was linear in the concentration range from 1.96×10⁻⁴ to 1.07×10⁻³ mol l⁻¹ with a detection limit of 8.0×10⁻⁵ mol l⁻¹. The relative standard deviation was 1.2% for 1.96×10⁻⁴ mol l⁻¹ isoprenaline solution (n=5). The procedure was successfully applied to the determination of isoprenaline in pharmaceutical preparations; the CuHCF modified carbon paste electrode gave comparable results to those results obtained using a UV spectrophotometric method.     

Novel coated-graphite membrane sensor based on N,N′-dimethylcyanodiaza-18-crown-6 for the determination of ultra-trace amounts of lead

A novel selective membrane electrode for determination of ultra-trace amount of lead was prepared. The PVC membrane containing N,N′-dimethylcyanodiaza-18-cown-6 (DMCDA18C6) directly coated on a graphite electrode, exhibits a Nernstian response for Pb²⁺ ions over a very wide concentration range (from 1.0×10⁻² to 1.0×10⁻⁷ M) with a limit of detection of 7.0×10⁻⁸ M (∼14.5 ppb). It has a fast response time of ∼10 s and can be used for at least 2 months without any major deviation in potential. The electrode revealed very good selectivity with respect to all common alkali, alkaline earth, transition and heavy metal ions. The proposed sensor was used as an indicator electrode in potentiometric titration of lead ions and in determination of lead in edible oil, human hair and water samples. The proposed sensor was found to be superior to the best Pb²⁺-selective electrodes reported in terms of detection limit and selectivity coefficient.     

Determination of Hg on poly(vinylferrocenium) (PVF)-modified platinum electrode

A new surface based on poly(vinylferrocenium) (PVF⁺)-modified platinum electrode was developed for determination of Hg²⁺ ions in aqueous solutions. The polymer was electrodeposited on platinum electrode by constant potential electrolysis as PVF⁺ClO₄⁻. Cl⁻ ions were then attached to the polymer matrix by anion exchange and the modified electrode was dipped into Hg²⁺ solution. Hg²⁺ was preconcentrated at the polymer matrix by adsorption and also complexation reaction with Cl⁻. Detection of Hg²⁺ was carried out by differential pulse anodic stripping voltammetry (DPASV) after reduction of Hg²⁺. Mercury ions as low as 5 × 10⁻¹⁰ M could be detected with the prepared electrode and the relative standard deviation was calculated as 6.35% at 1 × 10⁻⁶ M concentration (n = 6). Interferences of Ag⁺, Pb²⁺ and Fe³⁺ ions were also studied at two different concentration ratios with respect to Hg²⁺. The developed electrode was applied to the determination of Hg²⁺ in water samples.     

n-Alkanes, PAHs and surfactants in the sea surface microlayer and sea water samples of the Gerlache Inlet sea (Antarctica)

Sea surface microlayer (SML) and sea water samples (SSW) collected in the Gerlache Inlet Sea (Antarctica) were analysed for n-alkanes and polycyclic aromatic hydrocarbons (PAHs). The SML is a potential enrichment site of hydrophobic organic compounds compared to the underlying water column. Total concentration ranges of n-alkanes and PAHs (dissolved and particulate) in subsurface water (− 0.5 m depth) were 272-553 ng l^− 1 (mean: 448 ng l^− 1) and 5.27-9.43 ng l^− 1 (mean: 7.06 ng l^− 1), respectively. In the SML, the concentration ranges of n-alkanes and PAHs were 353-968 ng l^− 1 (mean: 611 ng l^− 1) and 7.32-23.94 ng l^− 1 (mean: 13.22 ng l^− 1), respectively. To evaluate possible PAH contamination sources, specific PAH ratios were calculated. The ratios reflected a predominant petrogenic input. A characterisation of surface active substances was also performed on SML and SSW samples, both by gas bubble extraction, and by dynamic surface tension measurements. Results showed a good correlation between n-alkanes, PAHs and refractory organic matter.     

Analysis of urinary neurotransmitters by capillary electrophoresis: sensitivity enhancement using field-amplified sample injection and molecular imprinted polymer solid phase extraction

Capillary electrophoresis (CE) has been investigated for the analysis of some neurotransmitters, dopamine (DA), 3-methoxytyramine (3-MT) and serotonin (5-hydroxytryptamine, 5-HT) at nanomolar concentrations in urine. Field-amplified sample injection (FASI) has been used to improve the sensitivity through the online pre-concentration samples. The cationic analytes were stacked at the capillary inlet between a zone of low conductivity - sample and pre-injection plug - and a zone of high conductivity - running buffer. Several FASI parameters have been optimized (ionic strength of the running buffer, concentration of the sample protonation agent, composition of the sample solvent and nature of the pre-injection plug). Best results were obtained using H₃PO₄–LiOH (pH 4, ionic strength of 80 mmol L⁻¹) as running buffer, 100 μmol L⁻¹ of H₃PO₄ in methanol–water 90/10 (v/v) as sample solvent and 100 μmol L⁻¹ of H₃PO₄ in water for the pre-injection plug.In these conditions, the linearity was verified in the 50–300 nmol L⁻¹ concentration range for DA, 3-MT and 5-HT with a determination coefficient (r²) higher than 0.99. The limits of quantification (10 nmol L⁻¹ for DA and 3-MT, 5.9 nmol L⁻¹ for 5-HT) were 500 times lower than those obtained with hydrodynamic injection. However, if this method is applied to the analysis of neurotransmitters in urine, the presence of salts in the matrix greatly reduces the sensitivity of the FASI/CE–UV method.Therefore, a solid phase extraction (SPE) on a dedicated imprinted polymer (MIP) was developed to extract specific neurotransmitters, catecholamines, metanephrines and indolamines, from urine. Matrix salts were thus discarded after sample extraction on AFFINIMIP™ Catecholamine & Metanephrine (100 mg) cartridge.Therefore, lower limits of quantification were determined in artificial urine (46 nmol L⁻¹ for DA, 11 nmol L⁻¹ for 3-MT and 6 nmol L⁻¹ for 5-HT).The application of this protocol MIP-SPE/FASI–CE–UV analysis of neurotransmitters in human urine gave rise to electropherograms with a very good base line and signal to noise ratios above 15.