无光敏剂光引发亲水性单体在嵌段聚醚氨酯膜上接枝聚合的研究

<正> 嵌段聚醚氨酯(SPEU)是一类应用广泛的医用高分子材料。用亲水性单体进行表面接枝改性,已有不少研究,接枝聚合方法有铈盐引发、辐射引发以及光敏引发等。 本文研究一种新的接枝方法,不加光敏剂,用紫外光照射,直接引发亲水性单体接枝于SPEU膜上、接枝的单体有丙烯酰胺(AAM)与N,N-二甲基丙烯酰胺(DMAA),从接枝前后膜的性能变化可以证实接枝反应的发生。文中研究了反应条件与单体结构对接枝率的影响,并通过模型化合物,对接枝部位进行了研究。     

棉纤维的N-异丙基丙烯酰胺接枝共聚及产物的温敏性研究

以硝酸铈铵(CAN)、过硫酸钾(KPS)及H2O2/H2A(双氧水/抗坏血酸)为引发体系,采用溶液自由基接枝法制备了具有温敏性的棉纤维N-异丙基丙烯酰胺接枝共聚物(cotton-g-PNIPAAm);在上述3种引发剂作用下的接枝反应可以达到的接枝率(G)排序为G(H2O2/H2A)>G(KPS)>G(CAN);研究了其他因素如引发剂浓度、反应时间、反应温度和单体浓度等对接枝率的影响,得出了优化的接枝反应条件;接枝样品的FTIR分析图谱和SEM观察均表明样品表面已接枝了聚N-异丙基丙烯酰胺;DSC分析显示,棉纤维N-异丙基丙烯酰胺接枝共聚物的低临界溶解温度(LCST)与纯的聚N-异丙基丙烯酰胺凝胶(LCST=32.48℃)相似,约为32~33℃;接枝率的变化对试样LCST的影响很小,但其可逆焓变(ΔH)会随接枝率的提高而增加;采用滴水试验法(AATCC 79)和毛效试验法(FZ/T 01071)检测棉纤维的N-异丙基丙烯酰胺接枝共聚物在不同温度时的吸水性变化,显示试样具有温敏特性,其中接枝率介于25%~45%的试样温敏性较高,过低或过高的接枝率均不利于获得高的温敏性;棉纤维的N-异丙基丙烯酰胺接枝共聚物试样的可逆焓变(ΔH)随试样膨胀/收缩时间变化的研究和分析结果表明,棉纤维的N-异丙基丙烯酰胺接枝共聚物对温度变化的响应比纯聚N-异丙基丙烯酰胺凝胶快.     

芴酮引发光接枝改性LDPE膜的研究

采用紫外光引发接枝表面改性的方法,以芴酮(FL)为引发剂,在低密度聚乙烯(LDPE)薄膜表面上接枝丙烯酸(AA)、甲基丙烯酸(MAA)、丙烯酸甲酯(MA)、甲基丙烯酸甲酯(MMA)、丙烯酰胺(AM)等单体,以赋予薄膜表面新的化学性质.考察了引发剂浓度、紫外光的辐照时间、辐照强度、单体种类对LDPE薄膜接枝程度的影响.结果表明,在一定范围内,增加芴酮浓度,可以提高单体的接枝率,但当芴酮浓度达到5%时,接枝率反而下降.延长辐照时间至4 min和提高紫外光的辐照强度达100 W/m2,均有利于接枝反应的进行.不同单体在LDPE膜上的接枝能力与单体的活性、单体与基材的相容性等因素有关.接枝后,LDPE与水的接触角下降程度不仅与单体在膜上的接枝量有关,还与接枝单体的亲水性能密切相关.     

N-甲基-N-(2-甲基丙烯酰氧乙基)苯胺敏化的丙烯腈光聚合

含有芳香叔胺基的烯类单体如N,N-二甲氨基苯乙烯,N-4-N',N'-二甲氨基苯基代丙烯酰胺(DMAPAA),N-4-N',N'-二甲氨基苯基代甲基丙烯酰胺(DMAPMA),甲基丙烯酸-4-N,N-二甲氨基苄酯(DMABMA),8-丙烯酰氧喹啉(AQ)等不仅与过氧化物构成氧化还原引发体系以引发其它烯类单体的光聚合还可以作为光敏剂引发烯类单体的光聚合。由于这类功能性单体在同一分子中既含有缺电子双键基团又含有供电子生     

马来酸酐-苯乙烯熔融接枝聚丙烯的影响因素及其性能研究

用单螺杆挤出机制备了马来酸酐 (MAH) 苯乙烯 (St)对聚丙烯 (PP)的多组分单体自由基熔融接枝体系 .研究证实了当两种单体物质的量比约为 1∶1时 ,接枝物的接枝率最高 ,而熔体流动速率 (MFR)最大 .对反应体系影响因素的研究表明单体用量和引发剂用量对不同单体用量比的系列接枝物的接枝率会产生不同的影响 ;另外 ,单体用量增加 ,接枝物的MFR减小 ,过氧化二异丙苯 (DCP)用量增加 ,接枝物的MFR增加 .对多单体熔融接枝聚丙烯PP g (MAH co St)的力学性能研究发现 ,选用合适的单体用量比、单体用量和DCP用量时 ,所制备的接枝物可具有与纯PP相当或更佳的力学性能     

N,N-二乙基丙烯酰胺与丙烯酸在聚丙烯薄膜表面光接枝制二元接枝膜及其温度、pH值敏感特性研究

以二苯甲酮为引发剂,聚丙烯薄膜(CPP)为基材,通过紫外光接枝的方法制备了具有温度和pH值双重敏感特性的聚N,N-二乙基丙烯酰胺(PNDEA)与聚丙烯酸(PAA)二元接枝膜.在PNDEA一次接枝膜的制备过程中,引发剂与单体配比相同时,本体接枝方法的接枝速率在反应初期明显高于溶液接枝方法;采用溶液法时,增大引发剂与单体配比等可提高接枝率.用本体法所制得的PNDEA一次膜光活化接枝PAA时接枝速率较溶液法高,并且能够实现较高的PAA接枝率.用红外光谱(FTIR)、X射线光电子能谱化学分析(ESCA)对接枝层组成的表征结果证实了二元接枝层的存在.在不同温度下,PNDEA一次接枝膜的FTIR谱图中酰胺Ⅰ带特征吸收峰发生位移表明它具有温度敏感特性.用扫描电子显微镜(SEM)对PNDEA接枝层表征结果表明,用不同接枝手段所制备的接枝膜具有不同的表面形貌.通过吸水率测定研究了二元接枝膜的温度及pH值敏感特性.     

N,N-二乙基丙烯酰胺与丙烯酸在聚丙烯薄膜表面光接枝制备二元接枝膜及其温度、pH值敏感特性研究

以二苯甲酮为引发剂,聚丙烯薄膜(CPP)为基材,通过紫外光接枝的方法制备了具有温度和pH值双重敏感特性的聚N,N-二乙基丙烯酰胺(PNDEA)与聚丙烯酸(PAA)二元接枝膜.在PNDEA一次接枝膜的制备过程中,引发剂与单体配比相同时,本体接枝方法的接枝速率在反应初期明显高于溶液接枝方法;采用溶液法时,增大引发剂与单体配比等可提高接枝率.用本体法所制得的PNDEA一次膜光活化接枝PAA时接枝速率较溶液法高,并且能够实现较高的PAA接枝率.用红外光谱(FTIR)、X射线光电子能谱化学分析(ESCA)对接枝层组成的表征结果证实了二元接枝层的存在.在不同温度下,PNDEA一次接枝膜的FTIR谱图中酰胺Ⅰ带特征吸收峰发生位移表明它具有温度敏感特性.用扫描电子显微镜(SEM)对PNDEA接枝层表征结果表明,用不同接枝手段所制备的接枝膜具有不同的表面形貌.通过吸水率测定研究了二元接枝膜的温度及pH值敏感特性.     

高锰酸钾引发魔芋粉/丙烯酰胺接枝共聚合及其增稠性研究

用KMnO4作引发刺对魔芋粉(KGM)与丙烯酰胺(AM)进行了接枝共聚反应．研究了引发剂浓度、接枝单体浓度、体系酸度、反应温度、反应时间以及KGM预氧化时间等条件对接枝效率的影响．结果表明：在适宜的条件下，接枝效率可达90％以上，并且接枝物的水溶性与增稠性得到较大的改善。     

含胺基功能性单体的聚合研究——Ⅶ.N-(4-N′,N′-二甲氨基苯基)代丙烯酰胺作为氧化还原引发体系组分的研究

<正> 我们曾报道过甲基丙烯酸-4-N,N-二甲氨基苄酯(DMABMA),4-N,N-二甲氨基苯乙烯(DMAS)等含芳香叔胺基的烯类衍生物不仅可以作为氧化还原引发体系组分引发烯类单体如甲基丙烯酸甲酯(MMA)的聚合,而且还进入MMA的聚合物链中。在另文中报道了两个芳香叔胺取代的丙烯酰胺:N-(4-N′,N′-二甲氨基苯基)丙烯酰胺(DMAPAA)和N-(4-N′,N′-二甲氨基苯基)甲基丙烯酰胺(DMAPMA)的合成及其聚合的研究,本文研究了这两个丙烯酰胺衍生物与过氧化苯甲酰(BPO)组成的氧化还     

淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂的制备

以过硫酸铵为引发剂,N,N-亚甲基双丙烯酰胺为交联剂,淀粉与丙烯酸/醋酸乙烯酯混合单体通过接枝共聚,制备了吸水及耐盐性能均较好的淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂(CGAV)。最佳工艺条件为:淀粉10.0 g,m(混合单体)∶m(淀粉)=4∶1,w(引发剂)=0.3%,w(交联剂)=0.05%,于45℃反应2h~3 h。在最佳工艺条件下制得的CGAV吸去离子水率760 g.g-1,吸0.9%NaC l水溶液率68 g.g-1。     

GMA熔融接枝EPDM的研究

以甲基丙烯酸缩水甘油酯（ＧＭＡ）为接枝单体，过氧化二异丙苯（ＤＣＰ）为引发剂，对三元乙丙胶（ＥＰＤＭ）进行了熔融接枝，在烃链上引入极性基团，以改善ＥＰＤＭ与极性聚合物的相容性。用差示扫描量热计（ＤＳＣ）研究了ＧＭＡ的聚合温度，用富里叶红外（ＦＴ－ＩＲ）、凝胶渗透色谱（ＧＰＣ）对接枝产物进行了表征。实验结果表明，产物的接枝率和凝胶量可以通过反应条件（温度、时间、反应物组成及加料方式）来控制。     

Neodymium oxide‐assisted melt free‐radical grafting of maleic anhydride on isotactic‐polypropylene by reactive extrusion

Rare earth oxide, neodymium oxide (Nd₂O₃), ‐assisted melt free‐radical grafting of maleic anhydride (MAH) on isotactic‐polypropylene (i‐PP) was carried out by reactive extrusion. The experimental results reveal that the addition of Nd₂O₃ into reactive system leads to an enhancement of the grafting degree of MAH, along with an elevated degradation of i‐PP matrix. When Nd₂O₃ content is 4.5 mmol %, the increment of the grafting degree of MAH (maximally) is up to about 30% compared with that of the related system without adding Nd₂O₃, while the severest degradation of i‐PP matrix simultaneously occurs. On the basis of the reaction mechanism of PP‐g‐MAH proposed before, the sequence of β‐scission and grafting reaction is discussed in detail. It is found that, for the reactive system studied, most tertiary macroradicals first undergo β‐scission, and then, grafting reaction with MAH takes place at the new radical chain ends. The imported Nd₂O₃ has no effect on the aforementioned reaction mechanism, whereas it enhances the initiating efficiency of the initiator, dicumyl peroxide (DCP). We tentatively explain the experimental results by means of synergistic effect between DCP and Nd₂O₃. It is calculated that the synergistic effect is maximal when the molar ratio of DCP to Nd₂O₃ is approximately 1:6. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 134–142, 2006     

Tailored rheology of a metallocene polyolefin through silane grafting and subsequent silane crosslinking

Polymer modification through silane grafting and its subsequent crosslinking allows the rheological properties of a polymer to be tuned from those of a viscous melt to those of a crosslinked elastic network. In this study, a metallocene polyolefin resin is grafted with vinyl trimethoxy silane (VTMS) using dicumyl peroxide (DCP) as the initiator and is subsequently crosslinked in an oxidative environment. Dynamic rheological experiments are conducted to elucidate the effects of DCP and VTMS concentrations on the grafting and ensuing crosslinking processes. We find that the addition of VTMS alone to the polymer produces no grafting. In contrast, the presence of DCP by itself leads to direct crosslinking between polymer chains as suggested by an increase in elastic modulus and complex viscosity. Samples containing both DCP and VTMS undergo silane grafting, with the extent of grafting increasing with increasing DCP concentration. This conclusion is borne out by both rheological and Fourier transform infrared measurements. The grafted samples undergo silane crosslinking only in an oxidative environment and at temperatures equal to or greater than 190 °C. During crosslinking, the samples undergo a transition from a viscous melt with frequency‐dependent moduli to a gel exhibiting frequency‐independent moduli with the elastic modulus exceeding the viscous modulus. However, the kinetics of crosslinking and the extent of the modulus increase are a function of the DCP concentration, with both exhibiting a maximum at a specific DCP and VTMS combination. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2468–2479, 2000     

Study of the Impact Resistance of Physically and Dynamically Vulcanized Mixtures of PP/EPDM

Physically and dynamically vulcanized (TPV) mixtures of polypropylene (PP) and ethylene propylene diene terpolymer (EPDM) are prepared by extrusion in order to improve the impact resistance of PP. To enhance the chemical compatibility and provide better interaction between the PP and EPDM in the physical mixtures, both polymers are modified with maleic anhydride (MAH) in solution using xylene as solvent and dicumyl peroxide (DCP) as initiator. The qualitative and quantitative determination of the degree of grafting is study by Fourier Transform Infrared Spectroscopy (FTIR) and varying the amount of DCP and/or amount of MAH in order to determine the optimum amounts to obtain the highest degree of grafting. The effect of the relation of PP/EPDM, the amount of reinforcement filler and mix rate are studied for modified polymer mixtures (PP-g-MAH/EPDM-g-MAH). For the TPV of PP/EPDM the effects of amount and triallylisocyanurate (TAC) as coupling agent in presence of different amounts of DCP are studied. The physical mixtures of modified polymers prepared with a PP/EPDM ratio of 80/20 and the TPVs blends prepared with a PP/EPDM ratio of 70/30 and containing 15% filler at 60 rpm show the highest impact resistance. The impact resistance, melt flow index and hardness of the different mixtures are measured to determine their possible applications to prepare front panels and bumpers for automobiles by injection molding.     

Studies on grafting of tris(2‐methoxyethoxy)vinylsilane onto ethylene‐propylene‐diene terpolymer

New graft copolymer was prepared by incorporating tris(2‐methoxyethoxy)vinylsilane (TMEVS) on ethylene‐propylene‐diene terpolymer (EPDM) by using dicumyl peroxide (DCP) as initiator, in Haake Rheocord 90 torque rheometer. The effect of EPDM concentration, TMEVS concentration, reaction time, reaction temperature and initiator concentration on the graft co polymerization was studied. The grafting efficiency of TMEVS on EPDM was confirmed by Fourier Transform infrared (FT‐IR) spectroscopy. The grafting efficiency increased with increase in the silane concentration upto 6% by weight. The grafting efficiency decreased beyond 6% by weight due to homopolymerization of TMEVS and non‐availability of carbon–carbon double bond in the EPDM terpolymer. The thermal properties of peroxide cured EPDM and hot water cured EPDM‐g‐TMEVS were studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis. The results show thermal properties like degradation tempertature and glass transition temperature of the EPDM‐g‐TMEVS were increased due to introduction of TMEVS on to EPDM terpolymer as well as the formation of thermally stable three‐dimensional network. Copyright © 2004 John Wiley & Sons, Ltd.     

Preparation and characterization of vinyltriethoxysilane grafted ethylene propylene diene terpolymer/linear low density polyethylene (EPDM‐g‐VTES/LLDPE) blends

Graft polymerization of vinyltriethoxysilane (VTES) onto ethylene‐propylene‐diene terpolymer (EPDM) was carried out in toluene using dicumylperoxide (DCP) as initiator. Effects of various parameters (EPDM content, VTES content, reaction time, reaction temperature and initiator concentration) on the grafting efficiency of VTES onto EPDM were investigated. At the optimum grafting efficiency conditions, EPDM‐g‐VTES was developed by melt mixing in a twin screw extruder and then linear (l), statically vulcanized (s) and dynamically vulcanized (d) blends of EPDM‐g‐VTES with linear low‐density polyethylene (LLDPE) with varying percentage compositions were prepared by melt mixing in the twin screw extruder. The grafting of VTES onto EPDM and its crosslinking was confirmed by FT‐IR. The characterization of mechanical properties such as tensile strength, elongation at break, Young's modulus and hardness, differential scanning calorimetry (DSC) analysis and morphology were studied and compared for the EPDM‐g‐VTES/LLDPE blends. The study reveals that the dynamically vulcanized blend improves the mechanical and thermal properties due to the presence of efficient interaction between component polymers when compared with other blends. Copyright © 2005 John Wiley & Sons, Ltd.     

Grafting of maleic anhydride on poly(L-lactic acid). Effects on physical and mechanical properties

Maleic Anhydride (MAH) was grafted onto poly(L-lactic acid) (PLLA) in the presence of dicumyl peroxide (DCP) as a radical initiator. The effect of the MAH and DCP concentrations on the grafting and the physical and mechanical properties of PLLA films were investigated. The glass transition temperature and crystallinity significantly decreased with addition of MAH. The thermal decomposition of the PLLA films was affected by the MAH content while the mechanical properties were almost unchanged. A slight increase in molecular weight was found, which could be attributed to either the MAH branching reaction or a possible crosslinking reaction between the PLLA chains increasing the chain entanglements.     

Reactive processing of polymers: Effect of bifunctional and tri-functional comonomers on melt grafting of glycidyl methacrylate onto polypropylene

Two reactive comonomers, divinyl benzene (DVB) and trimethylolpropane triacrylate (TRIS), were evaluated for their role in effecting the melt free radical grafting reaction of the monomer glycidyl methacrylate (GMA) onto polypropylene (PP). The characteristics of the GMA-grafting systems in the presence and absence of DVB or TRIS were examined and compared in terms of the yield of the grafting reaction and the extent of the main side reactions, namely homopolymerisation of GMA (poly-GMA) and polymer degradation, using different chemical compositions of the reactive systems and processing conditions. In the absence of the comonomers, i.e. in a conventional system, high initiator concentrations of peroxides were typically required to achieve the highest possible GMA grafting levels which were found to be generally low. Concomitantly, both poly-GMA and degradation of the polymer by chain scission takes place with increasing initiator amounts. On the other hand, the presence of a small amount of the comonomers, DVB or Tris, in the GMA-grafting system, was shown to bring about a significant increase in the grafting level paralleled by a large reduction in poly-GMA and PP degradation. In the presence of these highly reactive comonomers, the optimum grafting system requires a much lower concentration of the peroxide initiator and, consequently, would lead to the much lower degree of polymer degradation observed in these systems. The differences in the effects of the presence of DVB and that of TRIS in the grafting systems on the rate of the GMA-grafting and homopolymerisation reactions, and the extent of PP degradation (through melt flow changes), were compared and contrasted with a conventional GMA-grafting system.     

Peroxide-initiated crosslinking of maleic anhydride-modified low-molecular-weight polybutadiene. I. Mechanism and kinetics of the reaction

The crosslinking mechanism and kinetics of low-molecular-weight polybutadiene, its mixtures with maleic anhydride, and the products of its grafting with maleic anhydride and styrene, using dicumyl peroxide (DCP) as an initiator, were studied. It was shown that for all systems crosslinking is a radical polymerization of the double bonds. Modification of polybutadiene changes only the kinetic parameters of the crosslinking reaction and causes mainly a decrease of the termination step velocity. From DSC data the crosslinking reaction order, activation energy, and reaction heats were calculated.