Thermo-oxidative decomposition of crosslinked copolymers of methyl methacrylate with allylic isocyanurates

Studies were carried out on the isothermal thermo-oxidizing decomposition between 210 and 300° in air of polymethyl methacrylate and of copolymers with 1–30 mole per cent mono (N-2-hydroxypropyl), di(N-2-hydroxy, 3-allyloxypropyl) isocyanurates (MHPDHAIC) and tris(N-2-hydroxy, 3-allyloxypropyl) isocyanurates (THAIC) units.     

On the pyrolytic decomposition of cadmium carbonate

The pyrolytic decomposition of cadmium carbonate was studied by thermogravimetry (TG), derivative thermogravimetry (DTG), differential thermoanalysis (DTA) and exoemission of electrons (EEE).     

A kinetic expression for the pyrolytic decomposition of polytetrafluoroethylene

Despite the fact that the thermal decomposition of polytetrafluoroethylene has been extensively studied over the past six decades, some inconsistencies regarding the kinetic parameters, e.g. the order of the reaction, remain. Representative kinetic data are essential for practical purposes such as reactor design and scaling. In general the literature data refer to homogeneous bulk heating, whereas the case of the non-homogeneous heating of a single particle has not received attention. Data (reaction rate and pre-exponential factor) applicable to this latter case were experimentally determined from isothermal thermogravimetric analyses of the depolymerisation reaction of PTFE. The kinetic data obtained on coarse granules (800-1000 μm) are reported here. The rate law is consistent with a shrinking particle kinetic model, with chemical kinetics controlling phase-boundary movement. The mass loss rate is directly proportional to surface area. A rate law applicable to this case, and useable for geometries of arbitrary shape, is derived.     

Properties of vinylpyrrolidone-tert-butylphenyl methacrylate copolymers in solution

Copolymers of vinylpyrrolidone-p-tert-butylphenyl methacrylate (VP-MBPh) of several compositions were prepared by polymerization in benzene at 50°C using α′α′-azobisisobutyronitrile as initiator. Three of the copolymers were fractionated. Number-average molecular weights of fractionated samples were determined by osmotic pressure in benzene or 2-propanol. Kuhn–Mark–Houwink relations were established in benzene, chloroform, and 2-propanol. From the relation between M _n and the intrinsic viscosity (η), it appears that these random copolymers behave as predicted by the theory for flexible polymers. Abnormal viscometric behavior shown by one of the copolymers in nitromethane at 29°C (the theta temperature) is discussed. The Stockmayer–Fixman semiempirical method was used for estimating unperturbed dimensions from viscosity data obtained in chloroform, a good common solvent. Values of the viscosity parameter K_θ increase with the content of p-tert-butylphenyl methacrylate. In general, experimental K_θ values are higher than those calculated for the homopolymers. Excluded-volume parameters are estimated and discussed in relation to repulsive interactions between unlike monomer units.     

Assignments for the 1H-NMR of alkoxy groups in syndiotactic methacrylate copolymers—I: Methyl methacrylate-methacrylic acid copolymers and methyl methacrylate-diphenylmethyl methacrylate copolymers

Unusual assignments have been observed for the ¹H-NMR of alkoxy groups in syndiotactic methyl methacrylate-methacrylic acid (MMA-MAA) copolymers and methyl methacrylate-diphenylmethyl methacrylate (MMA-DPMMA) copolymers. Thereby, the alkoxy groups OCH₃ and OCH show a degenerate pentad assignment, in as much as the two monomer units nearest to the central monomer unit exert no differentiating influence on chemical shift, in contrast to the two next-to-nearest monomer units. By the use of copolymers possessing a tendency toward alternation with respect to compositional statistics, it is possible to distinguish between a degenerate pentad and a normal triad assignment. The reason for the degenerate pentad assignment is seen in specific conformations of the pentads, leading to the elimination of the differentiating influence on chemical shift for the two monomer units nearest to the central unit.     

Fluorescence of copolymers of 2-naphthyl methacrylate and methyl methacrylate

The fluorescence of a series of copolymers of 2-naphthyl methacrylate (2-NM) and methyl methacrylate (MMA) with various contents of 2-NM (obtained in chloroform, carbon tetrachloride and acetonitrile) was investigated. A linear dependence between the ratio of the excimer to monomer emission intensities (I_D/I_M) and the diad fraction (f_nn) of 2-NM monomer units was established. The relationship between I_D/I_M and f_nn · I_n (I_n = the mean sequence length of 2-NM units) fits a logarithmic curve. The results indicate that the excimer emission is determined mainly by the nearest neighbour naphthalene-containing monomer units in the copolymer chain. The copolymers obtained in acetonitrile have higher values of I_D/I_M than those obtained in chloroform and carbon tetrachloride. This difference is due to the higher content of mm-triads in copolymers from acetonitrile, confirmed by ¹H-NMR analysis of the samples of poly(methyl methacrylate) formed from copolymers of 2-NM and MMA.     

Photooxidative and pyrolytic degradation of methyl methacrylate-alkyl acrylate copolymers

Different compositions of poly(methyl methacrylate-co-methyl acrylate) (PMMAMA), poly(methyl methacrylate-co-ethyl acrylate) (PMMAEA) and poly(methyl methacrylate-co-butyl acrylate) (PMMABA) copolymers were synthesized and characterized. The photocatalytic oxidative degradation of all these copolymers were studied in presence of two different catalysts namely Degussa P-25 and combustion synthesized titania using azobis-iso-butyronitrile and benzoyl peroxide as oxidizers. Gel permeation chromatography (GPC) was used to determine the molecular weight distribution of the samples as a function of time. The GPC chromatogram indicated that the photocatalytic oxidative degradation of all these copolymers proceeds by both random and chain end scission. Continuous distribution kinetics was used to develop a model for photocatalytic oxidative degradation considering both random and specific end scission. The degradation rate coefficients were determined by fitting the experimental data with the model. The degradation rate coefficients of the copolymers decreased with increase in the percentage of alkyl acrylate in the copolymer. This indicates that the photocatalytic oxidative stability of the copolymers increased with increasing percentage of alkyl acrylate. From the degradation rate coefficients, it was observed that the photocatalytic oxidative stability follows the order PMMABA > PMMAEA > PMMAMA. The thermal degradation of the copolymers was studied by using thermogravimetric analysis (TGA). The normalized weight loss and differential fractional weight loss profiles indicated that the thermal stability of the copolymer increases with an increase in the percentage of alkyl acrylate and the thermal stability of poly(methyl methacrylate-co-alkyl acrylate)s follows the order PMMAMA > PMMAEA > PMMABA. The observed contrast in the order of photostability and thermal stability of the copolymers was attributed to different mechanisms involved for the scission of polymer chain and formation of different products in both the processes.     

Photocatalytic degradation of methyl methacrylate copolymers

The photolytic and photocatalytic degradation of the copolymers poly(methyl methacrylate-co-butyl methacrylate) (MMA-BMA), poly(methyl methacrylate-co-ethyl acrylate) (MMA-EA) and poly(methyl methacrylate-co-methacrylic acid) (MMA-MAA) have been carried out in solution in the presence of solution combustion synthesized TiO₂ (CS TiO₂) and commercial Degussa P-25 TiO₂ (DP 25). The degradation rates of the copolymers were compared with the respective homopolymers. The copolymers and the homopolymers degraded randomly along the chain. The degradation rate was determined using continuous distribution kinetics. For all the polymers, CS TiO₂ exhibited superior photo-activity compared to the uncatalysed and DP 25 systems, owing to its high surface hydroxyl content and high specific surface area. The time evolution of the hydroxyl and hydroperoxide stretching vibration in the Fourier transform-infrared (FT-IR) spectra of the copolymers indicated that the degradation rate follows the order MMA-MAA > MMA-EA > MMA-BMA. The same order is observed for the rate coefficients of photocatalytic degradation. The photodegradation rate coefficients were compared with the activation energy of pyrolytic degradation. In degradation by pyrolysis, it was observed that MMA-BMA was the least stable followed by MMA-EA and MMA-MAA. The observed contrast in the order of thermal stability compared to the photo-stability of these copolymers was attributed to the two different mechanisms governing the scission of the polymer and the evolution of the products.     

Conducting graft copolymers of pyrrole and thiophene with random copolymers of methyl methacrylate and 3-methylthienyl methacrylate

Random copolymers of 3-methyl thienylmethacrylate and methyl methacrylate were synthesized via free radical polymerization. Electro-copolymerizations of random copolymers with thiophene and/or pyrrole were carried out in acetonitrile-tetrabutylammonium tetrafluoroborate (TBAFB), water-p-toluene sulfonic acid (PTSA) solvent-electrolyte couples. Oxidative polymerization of thiophene functionalized random copolymer was also achieved by constant current electrolysis and chemical polymerization. The characterizations were done by conductivity measurements, cyclic voltammetry (CV), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermal gravimetry analysis (TGA), scanning electron microscopy (SEM).     

Thermal behaviour of copolymers of methyl methacrylate and 2-ethylhexyl methacrylate

Five copolymer samples containing different mole fractions of methyl methacrylate (MMA) and 2-ethylhexyl methacrylate (EHMA) were prepared by bulk polymerisation at 70°C using 0.2% benzoyl peroxide as an initiator. The copolymer composition was determined by¹H NMR spectroscopy. Molecular weight of copolymers was determined by gel permeation chromatography and viscosity measurements. Thermogravimetric experiments were conducted to evaluate activation energy for the degradation of copolymers. Two to four reaction stages for the weight loss were observed in the copolymers. A decrease in thermal stability was observed by an increase in EHMA content.     

Polyurea microcapsules from isocyanatoethyl methacrylate copolymers

The synthesis of two types of isocyanate side chain containing copolymers, poly(methyl methacrylate‐co‐isocyanatoethyl methacrylate) (P(MMA‐co‐IEM)) and poly(benzyl methacrylate‐co‐isocyanatoethyl methacrylate) (P(BnMA‐co‐IEM)), which were synthesized by Cu(0)‐mediated radical polymerization, is reported. Polymerization proceeded to high conversion giving polymers of relatively narrow molar mass distributions. The incorporation of the bulky aromatic groups in the latter copolymer rendered it sufficiently stable toward hydrolysis and enabled the isolation of the product and its characterization by ¹H and ¹³C NMR, and FTIR spectroscopy and SEC. Both P(MMA‐co‐IEM) and P(BnMA‐co‐IEM) were functionalized with dibutylamine, octylamine, and (R)‐(+)‐α‐methylbenzyl‐amine, which further proved the successful incorporation of the isocyanate groups. Furthermore, P(BnMA‐co‐IEM) was used for the fabrication of liquid core microcapsules via oil‐in‐water interfacial polymerization with diethylenetriamine as crosslinker. The particles obtained were in the size range of 10–90 µm in diameter independent of the composition of copolymer. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2698–2705     

pH Responsivity and micelle formation of gradient copolymers of methacrylic acid and methyl methacrylate in aqueous solution

A series of gradient copolymers of methacrylic acid (MAA)/methyl methacrylate (MMA) with four end-to-end composition profiles (uniform, linear gradient, triblock with linear gradient midblock, and diblock) but all having an average chain composition of ?F(MMA) ≈ 0.5 and an average chain length of 200 were synthesized via model-based, computer-programmed, semibatch atom-transfer radical copolymerization (ATRcoP). These samples allowed us to investigate systematically the effects of the gradient composition profile on the pH responsivity and micelle formation of the copolymers in an aqueous solution. Measurements included light transmittance, TEM, AFM, DLS, (1)H NMR, and pH titration. It was found that linear gradient, triblock, and diblock copolymers formed spherical micelles at high pH. The micelles of the linear gradient copolymer contained MMA units in their hydrophilic shells, and those of the triblock and diblock copolymers had all of their MMA units residing in their cores. The composition profile showed a strong effect on the degree of acid dissociation at a given pH. The conformational transition of the copolymer chains was determined by both the pH value and composition profile. Copolymers having sharper gradients required a lower pH to trigger the conformational transition and a narrower pH range to complete the transition.     

Thermal degradation of phenyl methacrylate-methyl methacrylate copolymers

The degradation behaviours of poly(phenyl methacrylate), four phenyl methacrylate-methyl methacrylate copolymers which span the composition range, and poly(methyl methacrylate) have been compared by using thermogravimetry in dynamic nitrogen and thermal volatilisation analysis (TVA) under vacuum, with programmed heating at 10°C/min. Volatile products have been separated by subambient TVA and identified and the cold ring fraction and partially degraded polymer have been examined by ir spectroscopy. Poly(phenyl methacrylate) resembles poly(methyl methacrylate) in degrading completely to monomer. Copolymers of phenyl methacrylate and methyl methacrylate are more stable than the homopolymers. On degradation, the major products are the two monomers. Minor products from all the copolymers include carbon dioxide, dimethylketene, isobutene and formaldehyde. Copolymers with low and moderate phenyl methacrylate contents show the formation of anhydride ring structures in the cold ring fraction and partially degraded copolymer, together with small amounts of methanol in the volatile products. Carbon dioxide is a more significant product at lower phenyl methacrylate contents.The mechanism of degradation is discussed.     

Viscoelastic properties of styrene-co-methyl methacrylate random copolymers

Viscoelastic properties of styrene-co-methyl methacrylate random copolymers have been determined over a temperature range covering the glass transition, the rubbery plateau, and the terminal zone and compared with polystyrene and polymethyl methacrylate homopolymers. Nonlinear behavior was observed in the variations of most of the physical and rheological characteristics with the methyl methacrylate content in the copolymer. Results are interpreted in terms of the rupture of polar-polar intermolecular interactions between ester groups due to the presence of styrene units.     

Thermal behaviour of copolymers of methyl methacrylate and iso-octyl/iso-decyl methacrylate

Thermal behaviour of copolymers of methyl methacrylate (MMA) with iso-octyliso-decyl methacrylate was investigated using dynamic thermogravimetry, mass spectroscopy and pyrolysis gas chromatography. The copolymer samples were stable upto 250 °C. Total loss in weight was observed around 400 °C. The degradation in homopolymers as well as copolymers proceeded by predominans loss of monomer.

---

Zusammenfassung Mittels dynamischer Thermogravimetrie, Massenspektroskopie und Pyrolysengaschromatographie wurde das thermische Verhalten von Kopolymeren aus Methylmethacrylat (MMA) und Isooktyl/Isodecyl-methacrylat untersucht. Die Kopolymerproben waren bis 250 °C stabil. Ein vollständiger Gewichtsverlust wurde bei 400 °C beobachtet. Der Abbau sowohl der Homopolymere als auch der Kopolymere erfolgt durch eine überwiegende Abgabe von Monomeren.

---

, - /- . /- . 250°. 400°. , .

     

Block copolymers of dodecafluoroheptyl methacrylate and butyl methacrylate by RAFT miniemulsion polymerization

Reversible addition‐fragmentation chain transfer (RAFT) miniemulsion polymerization of butyl methacrylate (BMA) and dodecafluoroheptyl methacrylate (DFMA) was carried out with 2‐cyanoprop‐2‐yl dithiobenzoate (CPDB) as chain transfer agent (CTA). Concentration effects of RAFT agent and initiator on kinetics and molecular weight were investigated. No obvious red oil layer (phase's separation) and coagulation was observed in the first stage of homopolymerization of BMA. The polymer molecular weights increased linearly with the monomer conversion with polydispersities lower than 1.2. At 75 °C, the monomer conversion could achieve above 96% in 3 h with [momomer]:[RAFT]:[KPS] = 620:4:1 (mole ratio). The results showed excellent controlled/living polymerization characteristics and a very fast polymerization rate. Furthermore, the synthesis of poly(BMA‐b‐DFMA) diblock copolymers with a regular structure (PDI < 1.30, PMMA calibration) was performed by adding the monomer of DFMA at the end of the RAFT miniemulsion polymerization of BMA. The success of diblock copolymerization was showed by the molecular weight curves shifting toward higher molar mass, recorded by gel permeation chromatography before and after block copolymerization. Compositions of block copolymers were further confirmed by ¹H NMR, FTIR, and DSC analysis. The copolymers exhibited a phase‐separated morphology and possessed distinct glass transition temperatures associated with fluoropolymer PDFMA and PBMA domains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1585–1594, 2007     

甲烷在活性炭上裂解制氢研究

在连续流动石英固定床反应器上研究了甲烷在活性炭上裂解制氢的反应,并对反应前后活性炭的比表面积以及孔径分布等的变化进行了测定。结果表明,甲烷在五种活性炭上的裂解行为基本相同,反应初期转化率最高,随着反应进行转化率逐渐降低直至一个平稳的状态;降低甲烷分压和增加甲烷与活性炭的接触时间可提高甲烷转化率;温度的升高有利于初始转化率的提高,但不利于活性炭的稳定性;反应后活性炭比表面积、孔容及微孔孔容都明显降低,平均孔径增大,孔径分布向中孔方向迁移,说明甲烷的裂解导致了活性炭孔特别是微孔内的炭沉积以及进一步的孔堵塞。     

Radiation degradation of copolymers of methyl methacrylate and 3-oximino-2-butanone methacrylate

Copolymers of methyl methacrylate and 3-oximino-2-butanone methacrylate (OM) were investigated as deep-UV and e-beam resists. Their increased sensitivity relative to PMMA (up to 50 times) was correlated with the radiation chemical yields of the volatile products and main chain scissions. The degradation of these copolymers, activated by the 3-oximino-2-butanone entity, is discussed in terms of energy absorption mechanisms and the subsequent scission reactions.