无线紫外光MIMO通信线性注水功率分配方法

将无线紫外光多输入多输出(MIMO)通信与线性注水算法相结合,首先建立基于线性注水算法的无线紫外光非直视MIMO通信模型,并推导出其信道容量模型,然后在信号发射端采用等功率分配和线性注水算法两种方法进行功率分配,研究在无线紫外光非直视MIMO通信系统中采用这两种方法对通信系统中信道容量的影响,并进行仿真分析验证.仿真结...     

基于自联想神经网络的可见光MIMO通信系统颜色检测

基于摄像头的多光源多输入多输出(MIMO)通信系统能够提高光源的利用率和传输带宽,但多光源之间的干扰和环境光的干扰为可见光的颜色判断带来了极大的困难。针对这种情况,提出了基于自联想神经网络的可见光MIMO颜色检测算法。设计了基于自联想神经网络的主成分提取方法,在训练速度和模型准确率方面取得平衡;提出了神经网络学习光源颜色的具体训练方法,基于欧氏距离决定光源的实际颜色符号。在真实的实验数据集的基础上完成了验证实验,结果显示该算法实现了较好的收敛速度和较高的检测准确率。     

室内MIMO可见光通信的接收特性

建立了一种基于MIMO的室内二次反射可见光通信的信道模型。通过模型仿真,从不同位置处接收面上探测器的不同间距、不同面积以及接收面横向、纵向旋转方面,分析了室内MIMO可见光通信的接收特性。仿真结果表明,在满足信号可恢复的条件下,接收面探测器间距d的变化对光信号接收的影响很小,不同接收位置的接收信噪比(SNR)也呈现不同的分布。另外,接收面横向旋转不会影响光信号接收,而纵向旋转具有一定的限制范围。     

基于可见光通信的LED布局与功率分配的同步优化

本文提出了一种基于融合改进策略的快速鲸鱼优化算法（FWOA）,用于解决室内可见光通信（VLC）系统中光信号分布不均匀的问题。该算法通过反向学习和非线性收敛因子提升了收敛速度,采取扰动搜索机制实现全局寻优。在考虑发光二极管（LED）部署高度的光源布局和功率分配方面,采取了同步优化方案。实验结果表明,在优化16个LED布局模型后,系统照度均匀度提升了7.39%～109.03%,接收功率的品质因子由5.25提高到12.23,同步优化后进一步提高至15.12。此外,实验发现,当LED数量存在限制时,通过选择合适的LED数量,可以在系统能量和性能之间达到较好的平衡。     

无背景噪声时光多输入多输出系统的信道容量

信道容量是通信系统能够达到的最大传输速率,是衡量通信系统通信能力的重要指标之一。在建立了光多输入多输出(MIMO)的信道模型之后,结合脉冲位置调制(PPM)分析了光MIMO系统的平均容量和中断容量;在无背景辐射的条件下,分别推导出了有无衰落时光MIMO平均容量封闭形式的近似表达式。在相同发射功率和传输带宽条件下,得到了光MIMO技术能成倍提高现有系统信道容量的结论。通过Monte Carlo仿真实验进一步证明了理论的正确性。     

基于空间光调制器的MIMO大气传输特性研究

大气湍流对无线光通信系统的影响不可忽视,为了更准确地反映实验室模拟多输入、多输出(MIMO)大气湍流信道的实际特征,提出了一种利用相位屏来模拟MIMO大气湍流信道的方法,并针对基于液晶空间光调制器（LC-SLM）的液晶调制法展开研究,通过实验验证该方法的可行性。实验结果表明：通过相位屏模拟MIMO大气湍流信道的激光光斑发生不同程度的畸变,湍流环境下两路激光发射系统比单路发射激光系统功率稳定性好,在前向纠错误差极限（3.8×10-3）下,单个发射单个接收系统的链路代价为10.5 dB,2个发射2个接收的MIMO系统的链路代价为9.3 dB。该项研究对于实验室模拟MIMO大气湍流信道实验方法提供一种新思路。     

基于区域划分的自适应可见光定位算法研究

为了提高传统可见光定位算法的定位精度,提出一种基于区域划分的新型自适应可见光定位算法.在对单光源和多光源定位算法的研究基础上,设计基于对称结构接收机的两光源定位算法来弥补边缘区域的定位误差.依据上述三种算法在不同区域的定位误差分布特性,构建公平性函数,并结合朗伯辐射模型,将定位区域划分为多个子区域.在定位阶段,先根据接...     

多光谱可见光通信信道串扰分析

在可见光通信领域, 通过波分复用技术可以增加信道个数, 从而提高系统通信容量. 然而发光二极管(LED)的辐射光谱具有一定线宽, 当信道个数增加, 信道间隔将变小, 尽管有滤光片的通道选择, 但LED的辐射光谱会出现重叠从而产生信道串扰. 本文基于LED光谱重叠现象分析了多光谱波分复用可见光通信系统的信道串扰问题. 首先结合LED的物理机制和实际LED的光谱形状对其光谱进行建模; 然后根据光谱重叠现象和可见光通信信道推导出信道串扰公式; 最后利用不同中心波长的LED在两通道可见光通信系统中验证了信道串扰公式的正确性. 仿真和实验结果表明, 当两信道的信道间隔大于28 nm时, 两信道之间的信道串扰不超过-13.6 dB. 对多光谱波分复用可见光通信系统的信道串扰分析对未来可见光通信增加信道数量有一定指导作用.     

多输入多输出量子密钥分发信道容量研究

量子安全通信是一个量子密钥分发过程,目前采用的通信技术严重制约了量子密钥分发的比特率.将多输入多输出（MIMO）技术应用于量子密钥分发系统,可提高量子密钥分发的比特率,促进量子安全通信向高速大容量发展.文中首先构造出MIMO量子密钥分发信道中多光子纠缠态Wigner算符矩阵.并在此基础上,推导出多光子双模压缩纠缠态Wigner算符矩阵和MIMO量子密钥分发信道容量.为开发稳健的MIMO量子安全通信空时处理算法和优化设计高性能MIMO量子密钥分发系统提供理论支撑和技术基础. 关键词： 多输入多输出 双模压缩态 多光子纠缠态 信道容量     

降低可见光通信不均匀限幅正交频分复用系统非线性限幅失真的功率分配方法

针对可见光通信中不均匀限幅光正交频分复用(ACO-OFDM)系统发光二极管(LED)非线性限幅失真严重的问题,提出了一种降低LED非线性限幅失真的最优功率分配方法。基于原信号直接叠加非线性限幅失真成分的限幅处理模型,分析了ACO-OFDM系统中的LED非线性限幅失真;利用有效信噪比来衡量限幅失真,将限幅失真转化为有效信噪比分析;基于有效信噪比最优的原则给出了光功率约束下降低限幅失真的最优偏置信号和ACO-OFDM信号功率分配。仿真结果表明,当信道的信噪比较低时,信道噪声起主导作用;当信道的信噪比较高时,限幅失真起主导作用。在光功率约束下若不考虑偏置信号的影响而直接取其值为LED最小输出功率限制,则系统误码率(BER)在信道信噪比大于40dB的情况下也始终大于10-2,而采用最优功率分配时可以保证系统具有较好的误码率性能,当光功率约束为200mW和250mW时,分别需要24dB和27dB的信道信噪比即可使得系统的误码率低于10-3。     

Simulation of MIMO channel characteristics for indoor visible light communication with LEDs

In order to study the characteristics of multiple input and multiple output (MIMO) channel, first, the basic components of the communication system are analyzed. And then, we present a simplified ray tracing method for optical MIMO system to obtain its channel impulse response and frequency response. This method using ray tracing to calculate the impulse of the channel limits the reflections within three times. Finally, its validity is verified by the numerical simulations, and its simulation results have been discussed. The channel bandwidth is gradually narrow, direct response is getting small, and the first response becomes large from the center to the corner.     

Blind channel estimation for DCO-OFDM based vehicular visible light communication

Blind channel estimation (CE) methods for OFDM based RF communication provide high-rate transmission by eliminating pilot overhead in conventional pilot-based methods, at the cost of lower accuracy. However, there is no work on the blind CE for OFDM based visible light communication (VLC) systems. In this paper, we propose a novel blind CE method for vehicular VLC with the goal of improving CE accuracy based on the exploitation of the channel statistics derived, by utilizing extensive amount of data collected for different communication angles, distances, and ambient light conditions. First, the normalized channel frequency response (CFR) of the V2LC channel is demonstrated to be invariant of inter-vehicular distance, relative transmitter/receiver zenith angle and ambient light. Then, this channel characteristic is exploited in the blind CE to improve its accuracy with two-step estimation of normalization factor. Extensive simulations at different vehicle speeds show that the proposed method outperforms the pilot-based and superimposed training-based CE methods in terms of spectral efficiency both for all modulation schemes and at all relative speeds. The proposed blind channel estimation (CE) method provides 9.77% increase in the spectral efficiency, compared to the second best method, superimposed training-based CE, at 20 dB signal-to-noise ratio (SNR) and 160 km/h relative speed, for 64-Quadrature Amplitude Modulation (QAM) Direct Current-Biased Optical Orthogonal Frequency Division Multiplexing (DCO-OFDM). Moreover, the real-time performance of the proposed blind CE is demonstrated for a realistic vehicle mobility scenario extracted from SUMO.     

Outage capacity analysis of the massive MIMO diversity channel

We consider the massive Multiple Input Multiple Output (MIMO) channel affected by independent and identically distributed Rayleigh fading, with linear processing at both transmitter and receiver sides to pursue full diversity, and analyze its outage capacity for large number of antennas. We first discuss the classical Single Input Multiple Output (SIMO) diversity channel that encompasses Maximal Ratio Combining (MRC) or Selection Combining (SC). For MRC, a numerical computation and a Gaussian Approximation (GA) are considered, whereas for SC an exact evaluation is presented. The analysis is then straightforwardly extended to the Multiple Input Single Output (MISO) diversity channel that encompasses Maximal Ratio Transmission (MRT) or transmit antenna selection. The general full diversity MIMO channel is finally considered, with optimal linear processing or simple antenna selection at both transmitter and receiver. If the number of antennas is sufficiently large on at least one side, the outage capacity of each considered diversity channel approaches that of a reference Additive White Gaussian Noise (AWGN) channel with properly defined Signal-to-Noise Ratio (SNR), which provides a performance benchmark. This conclusion is valid for large but realistic number of antennas compatible with the assumption of independent fading.     

单声线水声MIMO信道容量的研究

本文对水声MIMO(Multiple-Input-Multiple-Output)信道容量受收发阵元数目、间距,收发阵位置、方向,平均接收信噪比以及声速剖面的斜率的影响,在收发阵元之间只存一条声线的情况下,通过WKB近似进行了初步的研究。从计算结果可以看出,当收发阵元对之间只存在一条声线时,阵元间距会对MIMO信道容量产生重要影响:当收发阵元间距足够大时, MIMO系统的信道容量将随着接收信噪比和收发阵元数线性增加,一个m×m的MIMO系统的信道容量将为相应的 SISO(Single-Input-Single-Output)系统的m倍,收发阵的方向也会对MIMO系统信道容量产生较大的影响,另外,收发阵的深度、距离也会对水声MIMO信道容量产生影响,声速剖面的斜率在一般水声信道的声速变化范围内,对信道容量的影响不大。     

Closed-form CRLB and LPI power allocation strategies for MIMO radars with unneglectable clutter

This paper studies clutter’s effect on MIMO radar performance through obtaining closed-form Cramer Rao lower bounds (CRLBs) for the range and velocity parameters versus the powers assigned to the transmit antennas which resulted in more calculation’ complexity. To verify extracted CRLBs, the maximum likelihood estimation’s error variance (MLEEV) of range and velocity were derived in attendance of clutter. Based on obtained closed-form CRLBs, four optimized power allocation (PA) strategies are proposed which consider measurement error statistics as the objective function or constraints to improve radar performance. So, the calculated closed-form CRLBs are simplified to the closed-forms versus assigned powers to the transmitters. Simulation results verify the proposed CRLBs’ accuracy, and improvements have been made by proposed power allocations.     

基于重复编码的海上可见光通信大气信道建模

可见光通信作为一种新型无线通信技术,在海上舰船场景中的应用吸引了广泛的关注.海上可见光通信系统受多种因素的影响,包括海浪随机起伏和大气湍流,大气湍流将导致可见光信号的强度随机波动,降低可见光通信系统在大气中的链路质量.本文基于对数正态衰减分布,建立了采用重复编码的海上可见光通信的链路评估模型.在此基础上,根据Pierson-Moskowitz海谱,分析了海上风速、大气折射率结构常数、能见度、重复编码分集度以及接收器孔径对可见光通信系统平均误码率的影响.本文提出的海上大气链路评估模型可为海上可见光通信网络的搭建提供重要参考.     

室内可见光通信发光二极管阵列发射性能的研究

提出了一种基于Lambert辐射模型的发光二极管光源阵列发射天线光照度计算模型,对室内可见光通信发射天线进行了优化设计.分析了光源的空间分布形式、光源间距、光源中心光束与系统光轴夹角以及空间分布层间距等因素对光照度均匀性的影响.通过仿真模拟和分析,得到了圆形阵列天线在照度均匀性和通信传输信号稳定性方面都优于相同光源数目的矩形阵列天线,并且提高了10%左右;同时得出了在满足室内照明情形下,发光二极管阵列发射天线照度均匀度随光源间距及光源中心光束与系统光轴夹角的增加均呈现出先增加后减小的变化趋势,因此,光源间距和光源中心光束与系统光轴夹角均存在最优值;照度均匀度随空间分布层间距的减小而增加,并给出了5 m×5 m×3 m普通房间内发射天线阵列设计参数的最优值,使发射性能得到了优化,同时节省光源数13%,降低了成本.这些研究为发射天线系统的设计提供了理论依据,具有实用价值.