水滑石负载碘催化合成α-氨基腈类衍生物

以水滑石(LDHs)负载碘(I₂/LDHs)为催化剂,芳香醛、芳香胺和三甲基硅氰(TMSCN)为原料,合成了10种α-氨基腈类衍生物,其结构经¹H NMR确认。优化反应条件为:n_苯甲醛∶n_苯胺∶n_TMSCN=1.0∶1.0∶1.4,水滑石负载碘10(mol)%作催化剂,甲醇为溶剂,搅拌反应10min,收率最高可达98.3%。     

溴酸钠和氯化铁为助催化剂2,2,6,6-四甲基-N-氧化哌啶催化醇的氧化

建立了溴酸钠和氯化铁为助催化剂2,2,6,6-四甲基-N-氧化哌啶(NaBrO₃-FeCl₃-TEMPO)新型催化体系,以苯甲醇的氧化为研究对象,得出各成分与底物的最佳物质的量比为:2%TEMPO、35%NaBrO₃、3.7%H₂SO₄、2%FeCl₃·6H₂O。该体系在室温下可有效实现芳香醇、脂肪醇及杂环醇的氧化,收率高(99%)、选择性强(99%),在无氧条件下,仍表现出较好的催化活性。     

二氧化钛包裹碘单质(I2/TiO2)制备及其光催化降解苯酚

采用水热法,以Ti(SO₄)₂为钛源,KIO₃为掺碘剂制备了具有高可见光活性,高稳定性的二氧化钛包裹碘单质(I₂/TiO₂)光催化剂.利用X射线光电子能谱(XPS)、X射线晶体粉末衍射(XRD)、透射电子显微镜(TEM)和紫外可见漫反射光谱(DRS)等表征手段对样品进行表征.结果表明,I₂/TiO₂中除含有锐钛矿相二氧化钛外、还含有碘单质和碘酸;I₂/TiO₂粒径大小为45 nm左右;在波长384 nm至700 nm范围内,该催化剂有强烈的吸收.探讨了该催化剂的形成过程和可见光催化机理.以苯酚降解反应为探针,测定了I₂/TiO₂光催化活性.结果显示:在全谱光源照射下I₂/TiO₂活性略高于P25,在可见光范围内其活性是P25的3倍多.确定了降解苯酚的最佳条件:全谱光源照射,投加量为0.5 g/L,苯酚浓度大于10 mg/L,溶液pH为3.2.I₂/TiO₂重复使用4次后,催化活性没有明显下降.     

新型富勒烯C60有机钴配合物(η2-C60)(η5-RC5H4)CoPPh3 (R=H,CO2Et)的合成及性质研究

鉴于富勒烯C₆₀所具有的缺电子烯烃的特性¹以及CpCo(PPh₃)₂可与烯或炔反应生成钴杂环有机化合物,^2,3 因此我们设想如果用C₆₀代替烯、炔,令其与η⁵-RC₅H₄Co(PPh₃)₂(1) 或η⁵-RC₅H₄Co(PPh₃)(PhC≡CPh)(2)反应,则应得到一类新型的富勒烯C₆₀有机钴杂环化合物。然而与这一设想不同的是,上述反应并未得到预期的C₆₀钴杂环有机物,所得到的却是另一类新型的有机钴C₆₀衍生物(η²-C₆₀)(η⁵-RC₅H₄)CoPPh₃(3).此外,我们发现当3或2同I₂反应时,可生成C₆₀或PhC≡CPh配体被I₂置换产物η⁵-RC₅H₄Co(PPh₃)I₂(4)。     

四丁基碘化铵催化甲基丙烯酸甲酯的可逆-休眠自由基溶液聚合

以四丁基碘化铵(BNI) 为有机催化剂, 碘单质(I₂) 与偶氮二异庚腈(ABVN) 原位生成的碘代异庚腈为引发剂, 进行甲基丙烯酸甲酯(MMA) 的溶液聚合. 以甲苯为溶剂, MMA:I₂:ABVN的摩尔比为200:1:1.7, 考察了催化剂用量对聚合的影响. 结果表明, 加入催化剂可以缩短诱导期, 当I₂:BNI摩尔比为1:1时聚合反应的诱导期最短(1.7 h); 当BNI:I₂摩尔比为0.25:1~2:1之间时, 聚合物实测分子量与理论值十分接近, 分子量分布较窄, 分子量分布指数(M_w/M_n) 多在1.2以下. 考察了在N,N'-二甲基甲酰胺(DMF)、 四氢呋喃(THF)、 苯甲醚、 苯和甲苯5种溶剂中的聚合反应, 发现在苯和甲苯中聚合可控性最佳, M_w/M_n多在1.2以下; 苯甲醚和THF中聚合速率较快, 聚合物分子量分布较苯中的略宽. 以DMF为溶剂时所得聚合物分子量分布很宽, 聚合可控性差. 核磁共振分析聚合物为碘封端结构, 碘原子封端的聚合物链所占比为91.6%.     

Ru3(CO)9(TPPTS)3催化的水/有机两相芳香硝基化合物CO选择性还原的研究

将水溶性膦/钌配合物Ru₃(CO)₉(TPPTS)₃(TPPTS:三苯基膦三-间磺酸钠)用于以CO为还原剂的水/有机两相芳香硝基化合物选择还原为芳胺的反应,发现相转移催化剂对反应有明显的促进作用,其中以添加十六烷基三甲基溴化铵(CTAB)的效果最好.以邻氯硝基苯为底物考察了相转移催化剂浓度、NaOH浓度、反应温度、压力等对反应转化率和选择性的影响.当反应条件为120℃,4MPa,3mol/LNaOH时,反应8h,邻氯硝基苯的转化率和邻氯苯胺的选择性均可达到99.9%.而且对含有羰基、氰基的芳香硝基化合物也有很高的活性和选择性.催化剂循环3次后,邻氯硝基苯的转化率和邻氯苯胺的收率仍可达到92%.     

气态碘在COF-103上吸附的理论研究

采用第一性原理和巨正则蒙特卡罗方法,模拟研究了气态碘分子(I₂)在共价有机框架材料(COF-103)中的吸附行为,并讨论了气态氧化物、氯化物和挥发性有机化合物(VOCs)等杂质气体的竞争吸附影响.结果表明,I₂偏向以垂直方式吸附于COF-103苯环的碳原子位,其中,长程色散相互作用具有重要的贡献,色散能在吸附能中的占比最多可达46%.I₂与COF-103之间存在少量电荷转移,且可能形成具有弱共价相互作用的次级键.杂质气体中苯分子(C₆H₆)的吸附能和等量吸附热最大,与COF-103的亲和性最强,并且可以占据I₂的吸附位点,从而引起I₂吸附量的显著降低.     

弱配位辅助的Ru催化C-H环化反应合成新型3-芳基异香豆素类化合物

以2-氧硫叶立德芳乙酮类化合物为原料,通过弱配位辅助的Ru催化C-H活化过程简捷高效地构建了异香豆素类化合物,并推测了反应机理。以[RuCl₂(p-cymene)]₂为催化剂,HFIP为溶剂,AgNTf₂为添加剂,KOAc为碱,以33%~91%收率合成了14个目标产物,其中3个化合物未见文献报道,其结构经¹H NMR, ¹³C NMR和HR-MS(ESI)表征。反应条件温和,反应位点选择性高,底物普适性好,耐受多种官能团。     

仲胺转化为甲酰胺的接力催化（英文）

甲酰胺是重要的化工原料,广泛应用于农药和医药生产中,其合成方法备受关注.目前,主要通过胺与不同甲酰化试剂(甲酸、甲酸盐、甲酰胺和CO₂等)的N-甲酰化反应合成甲酰胺.但由于转酰化反应生成的副产物不可避免,原子经济性100%的直接甲酰化成为更理想的合成路径.典型的甲酰胺代表是N,N-二甲基甲酰胺(DMF),工业上通过CH₃OH-NaOCH₃催化剂催化二甲胺和CO直接甲酰化生成DMF.近年研究者发展了多种直接甲酰化的催化体系,例如N-杂环卡宾、KOH、K₂CO₃和Co@N掺杂碳催化剂和PdCo双金属催化剂等.本课题组也报道了Ru修饰的氧化铈(Ru/CeO₂)和羟基磷灰石(Ru-HAP)催化的胺直接甲酰化(Green Chem.,2017,19,88-92和ChemCatChem,2021,13,41594163).然而,相较于伯胺,仲胺的直接甲酰化合成甲酰胺更加困难.因此,开发一种新的仲胺转化策略进而合成高附加值的甲酰胺非常必要.本文发展了一种基于羟基磷灰石负...     

一种合成多氟联苯类化合物的新方法

以CuI为催化剂,芳胺与多氟苯经重氮化/偶联一锅反应生成了6个多氟取代的联苯类化合物(3a~3f),收率56%~82%,其结构经¹H NMR, ¹⁹F NMR和EI-MS确证。在最佳反应条件［1a 2 mmol, 20%CuI为催化剂,150%四丁基碘化铵为碘化试剂,V(DMSO）:V（MeCN）=1 : 1为溶剂,于130 ℃反应4 h］下,3a收率75%。     

Molecular iodine preconcentration and determination in aqueous samples using poly(vinylpyrrolidone) containing membranes

Membranes for preconcentration of molecular iodine were developed by two different routes: (i) UV-grafting of 1-vinyl-2-pyrrolidone in the pores of microporous poly(propylene) host membrane (grafted membrane), and (ii) physical immobilization of preformed poly(vinylpyrrolidone) (PVP) in a plasticized cellulose triacetate matrix to form the polymer inclusion membrane (PVP-PIM). The UV-grafted PVP-membrane was found to be hydrophilic (water uptake capacity = 166 wt.%), while the PVP-PIM was found to be highly hydrophobic (≈2 wt.%). PVP-PIM was found to uptake only I₂ from aqueous sample whereas I₂ and I₃⁻ were sorbed in the grafted membrane. This selectivity of PVP-PIM towards I₂ was attributed to its hydrophobicity that allows only neutral I₂ to interact with PVP in the membrane matrix. Thus, the selective preconcentration and quantitative determination of I₂ in aqueous sample was carried out using PVP-PIM. As PVP-PIM was optically transparent, the characteristic absorbance of PVP–I₂ complex (λ_max = 361 nm) could be used for quantitative determination of I₂ in the membrane. The instrumental neutron activation analysis (INAA) of the I₂-loaded PIM samples indicated that 82% could be sorbed into the PIM samples from the solution within 10 min of equilibration time. This membrane was applied to I₂ determinations in the samples of ¹³¹I radiotracer. The concentration level of iodine species in these samples were in sub-ppb level. Therefore, these samples were ideal for testing the preconcentration efficiency of the membrane towards I₂ by monitoring the radioactivity of ¹³¹I. The amounts of I₂ in the aqueous samples were standardized by conventional solvent extraction of I₂ with the chloroform for validating the preconcentration efficiency of PVP-PIM. The detection limit of I₂ in aqueous samples by INAA hyphenated with PVP-PIM was found to be 0.3 ppb for a sample size of 25 mL.     

Application of an electrochemical membrane reactor to the thermochemical water splitting IS process for hydrogen production

The Bunsen reaction (SO₂ + I₂ + 2H₂O = H₂SO₄ + 2HI) in the thermochemical IS process to produce hydrogen was successfully employed using an electrochemical membrane reactor. H₂SO₄ and HI were concentrated in the anode side and the cathode side of the reactor, respectively. I₂ is the dominant bulk of the recycling chemicals in this process, and I₂ concentration at the outlet of the reactor was reduced ca. 93% by using this technique. The electric energy consumption for the reaction was about 50% smaller by reducing the concentration of I₂ indicating that the IS process can be operate efficiently at low I₂ concentration. The reaction was carried out for 4 h, and the HI concentration was increased by 26%. This amount was the same within 10% as the values calculated from the total loaded electricity. In order to decrease the overpotential at the anode side, small amount of HI was added to the anode side solution. The total voltage was reduced by 0.03 V by the addition of HI.     

Synthese und Eigenschaften einiger Iodtrisilane

The syntheses and properties of the iodotrisilanes (IH₂Si)₂SiH₂, (IH₂Si)₂SiHI, I₃SiSiI₂SiH₃, (I₃Si)₂SiH₂ and Si₃I₈ are reported. All trisilanes were synthesized from the appropriate phenyltrisilanes and hydrogen iodide, with the exception of I₅Si₃H₃, which was prepared by thermolysis of I₃SiSiH₃. The ²⁹ Si-chemical shifts and ²⁹Si²⁹Si-coupling constants are reported. ab]Die Synthesen und Eigenschaften der Iodtrisilane (IH₂Si)₂SiH₂, (IH₂Si)₂SiHI, I₃SiSiI₂SiH₃, (I₃Si)₂SiH₂ und Si₃I₈ werden beschrieben. Bis auf I₅Si₃H₃, das während der Thermolyse von I₃SiSiH₃, entstand, wurden alle Iodtrisilane aus den entsprechenden Phenyltrisilanen mit Iodwasserstoff hergestellt. Die ²⁹Si-Verschiebungen und ²⁹Si²⁹Si-Kopplungskonstanten werden mitgeteilt.     

正常与癌症肺组织的傅里叶变换红外光谱差异的研究

傅里叶变换红外(FTIR)光谱可以在分子水平上研究细胞和组织等复杂的生命体系,提供分子结构和组成的信息.我们发展了一种用于直接测定肿瘤及正常组织红外光谱的方法,对16例肺癌及其癌旁正常组织进行了测定.结果表明,对于正常和癌变的肺组织,FTIR光谱中存在显著差异,相关谱带的相对峰高比可以表征这些差异.因此,傅里叶变换红外光谱可以用来诊断癌症与正常的肺组织,有望成为肿瘤快速诊断的新方法.     

Detection of Cholangiocarcinoma with Fourier Transform Infrared Spectroscopy and Radial Basis Function Neural Network Classification

The aim of this study was to explore the possibility of applying Fourier transform infrared(FTIR) spectroscopy as a medical diagnostic tool based on a neural network classifier for detecting and classifying cholangiocarcinoma. A total of 51 cases of bile duct tissues were obtained and later characterized by FTIR spectroscopy prior to pathological diagnosis. The criteria for classification included 30 parameters for each FTIR spectra, including peak position(P), intensity(I) and full width at half-maximum(FWHM), were measured, calculated and subsequently compared against the normal and cancer groups. The FTIR spectra were classified by the radial basis function(RBF) network model. For establishing the RBF, 23 cases were used to train the RBF classifier, and 28 cases were applied to validate the model. Using the RFB model, nine parameters were observed to be pronouncedly different between cancerous and normal tissue, including I₁₆₄₀, I₁₅₅₀, I₁₄₆₀, I₁₄₀₀, I₁₂₅₀, I₁₁₂₀, I₁₀₈₀, I₁₀₄₀ and P₁₀₄₀. In the RBF training classification, the accuracy, sensitivity, and specificity of diagnosis were 82.6%, 80.0%, and 84.6%, respectively. While validating the classification, the accuracy, sensitivity, and specificity of diagnosis were 78.6%, 75.0%, and 81.2%, respectively. The results suggest that FTIR spectroscopy combined with neural network classifier could be applied as a medical diagnostic tool in cholangiocarcinoma diagnosis.     

甲状腺癌微转移淋巴结的红外光谱检测

采用衰减全反射(ATR)探头和傅里叶变换红外光谱(FTIR)仪测定了新鲜离体的甲状腺癌微转移颈部淋巴结(16枚)和非转移性淋巴结(16枚)的FTIR光谱, 配对比较了两组光谱13个谱带的峰位、相对峰强及半高宽等38个FTIR参数, 明确了甲状腺癌微转移淋巴结的光谱特征.结果表明, 与非转移性淋巴结相比, 微转移淋巴结光谱中与蛋白、脂质、糖类和核酸相关的谱带均发生了明显变化:与蛋白质相关的谱带的相对峰强I₃₂₈₀/I₁₄₆₀和I₁₆₄₀/I₁₄₆₀显著升高, 半高宽F₁₆₄₀显著增宽, 而F₁₅₄₆则变窄; 与脂类相关的相对峰强I₁₄₀₀/I₁₄₆₀明显增高; 与糖类相关的1165 cm^-1处谱带的相对峰强I₁₁₆₅/I₁₄₆₀显著降低; 与核酸相关的1240 cm^-1处谱带的相对峰强I₁₂₄₀/I₁₄₆₀显著升高.结果表明, FTIR能够检测出甲状腺癌的微转移淋巴结, 可能应用于甲状腺癌病人的精准手术治疗.     

NO2、H2O和N2对碘荧光的猝灭

核燃料后处理工业产生的废气中的129I2被排到大气中会造成严重的环境污染,因此迫切需要一种简便、快速而又足够灵敏的检测方法．中子活化分析法的检测极限可达4·0×107mole／cm3[1],虽然其灵敏度可满足要求,但因耗时长无法用于实时监测·激光诱导荧光法（LIF）是一种选择性好且灵敏度高的方法,已被广泛用于痕量物质的测定．该方法用于测定微量碘也已有报道[2,3],Goles等[3]用单模CW激光在580nm波长激发碘分子,用光子计数检测,测定纯129I2检测极限为2×109mole／cm3．但LIF法的最大缺点是荧光的猝灭会使检测灵敏度显著下降．Atsu…     

Oxidative-addition to a four-coordinate tin(II) complex supported by octamethyldibenzotetraaza[14]annulene dianion ligation, [η-Me8taa]Sn: The syntheses and structures of [η-Me8taa]SnI2 and *[η-Me8taa]SnI(THF)**I3*

The four-coordinate tin(II) complex [η⁴-Me₈taa]Sn undergoes oxidative addition of I₂ to give six-coordinate [η⁴-Me₈taa]SnI₂, in which the iodide ligands exhibit a trans arrangment. Abstraction of I⁻ from [η⁴-Me₈taa]SnI₂ is facile, as indicated by the rapid formation of the triiodide derivative *[η⁴-Me₈taa]SnI(THF)**I₃* upon treatment with I₂ in the presence of THF. The molecular structures of [η⁴-Me₈taa]SnI₂ and *[η⁴-Me₈taa]SnI(THF)**I₃* have been determined by X-ray diffraction.     

Angular momentum polarization in molecular beams of I2 and Na2

The degree of molecular alignment, due to nozzle expansion, has been determined in supersonic beams of I₂ and Na₂, using the technique of laser-induced fluorescence. It is found that the anisotropic distribution of angular momenta is of the form 1 + ₂P₂(cos ). The alignment appears to be small for I₂ while for Na₂ a considerably larger effect is measured. Two internal states are studied, v = 0, J = 28 and v = 3, J = 43; both under various source conditions. It is found that the alignment depends on the internal state of the molecule and for each state can be described as a unique function of pd, the product of source pressure and nozzle diameter. The results are explained using a moel based on scattering between atoms and dimers with different velocity distributions. It is suggested that alignment may be a general feature in seeded molecular beams containing nonspherical components.     

利用H2O2-KI-鲁米诺体系化学发光法测定痕量钼

钼(Ⅵ)可以催化H₂O₂氧化I^-的反应,生成的I₂在碱性水溶液中能氧化鲁米诺而产生化学发光^[1],本文将这两个反应结合起来,建立了铝的化学发光分析法,方法有较高的灵敏度,检出限为6×10^-10g/cm³Mo,测定的相对标准偏差小于6%,工作曲线的线性范围是1×10^-9～1×10^-7g/cm³Mo,用EDTA作掩蔽剂,排除了大多数金属离子的干扰,方法有较好的选择性,应用此法对一些粮食样品中的痕量钼进行了测定,结果比较满意。