可粘贴超疏水薄膜的制备

通过聚二甲基硅氧烷(PDMS)与碳纤维织物复合, 采用模板法在PDMS聚合物表面构筑微阵列结构, 制备了一种具有可重复粘贴性的超疏水薄膜. 研究结果表明, 该薄膜微结构表面的接触角为154°, 滚动角为14°, 具有低黏附的超疏水特性. 而PDMS与碳纤维织物的紧密结合, 赋予了超疏水薄膜较高的黏接力和力学性能, 断裂强度达到116.96 MPa. 所制备的超疏水薄膜可粘贴于多种材料表面, 同时经过30 d的长时间粘贴以及50次的循环粘贴后, 该薄膜依然保持着较高的黏附性能及超疏水特征, 表明超疏水薄膜具有良好的力学稳定性及耐久性, 满足长时间可重复使用的要求, 可应用于对破损超疏水涂层的快速、 大面积粘贴修复.     

超声刻蚀法构建分级结构的超疏水表面

在湿法刻蚀和超声空化的基础上, 采用超声刻蚀法制备了具有微纳米分级结构的超疏水表面. 以等体积比的硝酸/乙醇(体积分数为4%)和双氧水(质量分数为30%)的混合溶液作为刻蚀剂, 在室温下对60Si2Mn钢、 60^#钢、 T10钢、 Cr06钢、 65Mn钢和硅钢表面超声刻蚀2~10 min, 构建出多种形貌的微纳米分级结构. 上述表面经氟硅烷修饰后具有超疏水性, 水的表观接触角高达157.0°, 155.8°, 157.4°, 154.9°, 157.6°和156.8°, 滚动角分别为6.5°, 19.2°, 6.1°, 7.8°, 6.7°和7.2°. 与常规刻蚀方法相比, 超声刻蚀的化学刻蚀作用因与空化作用耦合而得到强化和改变, 从而在钢表面构建出分级结构. 由于材料表面微结构形貌和固/液界面接触状态不同, 制得的超疏水表面表现出的润湿行为也不同. 超声刻蚀法简单易行, 成本低廉, 适用于其它金属表面构建微纳米分级结构和超疏水表面.     

溶液浸泡结合表面涂层制备超疏水-超疏油表面

超疏水-超疏油材料在防污、防水、防油等领域有广泛的应用前景而引起人们极度关注。 本文用全氟辛酸溶液浸泡锌粉制得超疏水-超疏油锌粉,用聚乙烯醇胶将超疏水-超疏油锌粉粘合、固定到玻璃、木头、塑料、不锈钢、纸片、石头表面后可制得超疏水-超疏油表面,水滴、油滴在其表面的接触角均超过150°。 锌粉与全氟辛酸反应后生成Zn[CF₃(CF₂)₆COO]₂,氟代长链烷基的低表面能化学组成与微纳米粗糙结构的协调作用使其表现出超疏水、超疏油性能。 相关研究有望为超双疏材料的设计、制备及其在自清洁、防水防油及抗污等领域的应用提供借鉴。     

一种新型钼钒多酸化合物的合成、结构与荧光性能

采用水热技术,合成了一种新型四帽Keggin结构多酸化合物[H₃Mo₈^ⅥV₈^ⅣO₄₀(AsO₄)](en)₂(4,4-bipy)₇·9H₂O(en:乙二胺;bipy:联吡啶)(1),并对化合物进行了元素分析、红外光谱、X射线光电子能谱和X射线单晶结构分析。 晶体结构分析表明, 化合物属三斜晶系,P1空间群,晶胞参数a=1.47395(5) nm,b=1.48172(6) nm,c=1.62881(7) nm,α=66.16(3)°,β=87.15(2)°,γ=63.42(1)°,V=2.8723(2) nm³,Z=1,R₁=0.0728,wR₂=0.2014。 化合物由四帽Keggin多酸阴离子、4,4'-联吡啶、乙二胺和结晶水分子构成,化合物分子间存在大量的氢键,使化合物1形成3-D超分子结构。 荧光测试表明,化合物1能发出较强的荧光,有可能成为潜在的光活性材料。     

亚磷酸锌无机-有机杂化化合物的合成与结构表征

在水热条件下, 以1,6-己二胺为模板剂合成了一个三维(3D)亚磷酸锌无机-有机杂化化合物(C₆N₂H₁₆)_0.5ZnHPO₃(ZnHPO-CJ15), 并对其单晶结构进行了解析. 结果表明, ZnHPO-CJ15晶体属单斜晶系, P2₁/c空间群, a=1.19587(7) nm, b=0.82766(5) nm, c=0.77756(5) nm, α=90.00°, β=95.8370(10)°, γ=90.00°, V=0.76562(8) nm³, Z=1. ZnHPO-CJ15具有层柱状结构, 其骨架结构是由ZnO₃N四面体和HPO₃假四面体连接构成的二维4×8元环网层结构, 层与层之间由1,6-己二胺分子与Zn配位柱撑连接形成三维结构.     

聚酯织物表面耐用超疏水涂层的制备及在油水分离中的应用

使用在含有甲基MQ(M:单官能团Si-O单元R₃SiO_1/2, Q:四官能团Si-O单元SiO₂)硅树脂与疏水SiO₂的二甲苯溶液中浸渍的方法,在聚酯织物表面制备了耐用超疏水涂层。经过处理后,微米级聚酯纤维表面被紧密的疏水纳米颗粒包裹,通过这种方法降低了纤维的表面能。聚酯织物展现出良好的超疏水特性,与水滴的静态接触角为156°,滚动角为5°。得到的超疏水聚酯织物在机械磨损、酸碱环境及紫外线照射条件下,表现出了良好的稳定性。此外,用超疏水聚酯织物作为过滤材料得到的油水分离效率达99%以上。该方法为大面积工业制备超疏水织物提供了新的思路。     

AOPAN@Mg(OH)2多层次电纺纤维膜的制备及除铬性能

以含有—NH₂和C═N的偕胺肟化聚丙烯腈(AOPAN)纳米纤维膜为载体, 通过水热法在AOPAN纳米纤维膜表面原位生长片状Mg(OH)₂纳米粒子, 得到具有多层次结构的有机-无机电纺复合纳米纤维膜[AOPAN@Mg(OH)₂], 并研究了AOPAN@Mg(OH)₂的除铬性能. 研究结果表明, 当水热温度为40 ℃, 水热时间为7 h时, AOPAN纳米纤维膜表面形成了明显的多层次结构的Mg(OH)₂纳米晶体. 当溶液pH=2时, AOPAN@Mg(OH)₂复合纳米纤维膜对Cr(Ⅵ)的吸附符合Langmuir模型, 且满足二级动力学方程, 5 h后最大吸附量达到123.5 mg/g. AOPAN@Mg(OH)₂复合纳米纤维膜中含有—NH₂基团和Mg(OH)₂纳米粒子, 在酸性条件下可以质子化为带正电的—N\begin{array}{c}{H}_3^{+}\end{array}和Mg(OH)₂H⁺, 通过静电吸附更易与HCr\begin{array}{c}{O}_4^{-}\end{array}结合. 此类复合纳米纤维膜材料在水体中易取出, 并且在稀NaOH溶液中可以解吸附, 循环使用4次去除率仍可以保持在50%以上.     

三嗪-吡唑钌配合物的合成、结构及光催化活性

光催化具有无污染、安全高效等优点,已成为环保领域的研究热点。 本文选择2,4-二(3,5-二甲基吡唑)-6-二乙基胺-1,3,5-三嗪(L₁)和2, 6-二[3-(5-甲基吡唑基)]吡啶(L₂)为配体、以RuCl₃为金属源,合成了3种配合物[Ru(L₁)Cl₃](1)、[Ru(L₂)₂]·Cl₃(2)和[Ru(L₂)₂]·(H₂BTC)·(HBTC)·H₂O(3),同时进行了IR、UV-Vis、TG及X射线衍射等表征,并对配合物在光催化降解罗丹明B方面进行了探讨,结果表明,配合物13均具有一定程度的光降解效果,降解效果分别为46.8%、44.7%和40.4%。 相同条件下,加入H₂O₂后的配合物13的降解效果比金属盐、配体及H₂O₂单独存在时的降解效果好。     

不同超疏水铜表面的湿法氧化制备及抗冷凝性能

分别以过硫酸钾、 过硫酸铵及氨水为氧化剂, 在铜表面制得纳米结构, 并用十七氟癸基三乙氧基硅烷(FAS-17)进一步氟化处理, 获得了差异化超疏水表面. 比较了不同氧化剂对反应结果的影响, 并分析了氧化反应的历程. 实验结果表明, Cu首先被O₂氧化成CuO超薄层, 然后水解变成Cu(OH)₂, 并进一步被OH^-或NH₄OH络合成蓝色溶液. 不同形貌纳米结构是Cu(OH)₂在饱和析出过程中沿固定晶面堆砌的结果. 最后对不同纳米结构超疏水表面的耐水蒸气冷凝情况及微观机理进行了分析, 证实只有较密、 较垂直的纳米针结构表面才耐水蒸气冷凝, 即冷凝水滴在其上出现快速自迁移现象.     

三环已基锡L-扁桃酸酯配合物的合成、结构及性质

三环己基氢氧化锡与L-扁桃酸(物质的量比1:1)在苯和乙醇混合溶剂中反应合成了三环己基锡L-扁桃酸酯。 经X射线衍射方法测定了其晶体结构,配合物属斜方晶系,空间群为P2₁2₁2₁,晶体学参数a=0.80825(4) nm,b=1.77151(8) nm,c=1.8385(2) nm,α=β=γ=90°,V=2.6324(2) nm³,Z=4,D_c=1.310 g/nm³,μ(MoKα)=9.92 cm^-1,F(000)=1080,R₁=0.0472,wR₂=0.1341。 中心锡原子与环己基碳原子和氧原子构成畸型四面体。 对其结构进行量子化学从头计算,探讨了配合物的稳定性、分子轨道能量以及一些前沿分子轨道的组成特征。 研究了配合物的热稳定性、电化学性能、圆二色谱和体外抗癌活性。     

表面化学接枝改性阻燃棉织物的制备与性能

采用高碘酸钠对棉织物表面进行选择性氧化生成醛基,选取乙二胺与醛基反应,通过膦氢化加成反应将阻燃剂亚磷酸二甲酯接枝到棉织物表面,最后通过三羟甲基三聚氰胺对棉织物表面进行接枝改性,制备了含三羟甲基三聚氰胺/乙二胺/亚磷酸二甲酯阻燃棉织物.通过傅里叶红外光谱（FTIR）对改性后棉织物的结构进行了表征,通过极限氧指数（LOI）测试研究了其阻燃性能,通过锥形量热测试研究了其燃烧行为,通过在40℃皂水中洗涤10次考察了其耐水性能,通过扫描电子显微镜测试了其表面及燃烧后炭层的形貌.研究结果表明,经表面改性后,棉织物的LOI值由（19.5±1.0）%提高到了（43.1±1.0）%,经耐水洗测试后,LOI值仅下降至（42.6±1.0）%,保持了非常好的阻燃性能,表明通过表面接枝方法制备的三羟甲基三聚氰胺/乙二胺/亚磷酸二甲酯阻燃棉织物具有非常好的耐水洗性能.表面阻燃改性提高了棉织物在燃烧过程中的成炭性能,形成的连续膨胀的炭层较好地保护了内部织物,抑制了织物的降解和燃烧,从而提高了棉织物的阻燃性能.     

Preparation and characterization of flame‐retardant lamellar Mg(OH)2 thin films on citric acid‐treated cotton fabrics

Preparation and characterization of lamellar magnesium hydroxide (Mg(OH)₂) thin films on cotton fabrics are reported in this paper. Mercerized cotton fabrics were treated with citric acid, so carboxyl groups were introduced to the surface of the fabrics. Mg(OH)₂ seeds were first adsorbed on the citric acid‐treated cotton fabrics and then Mg(OH)₂ thin films grew on the fabric through secondary growth method. Kinetics and isotherm studies found that the adsorption of Mg(OH)₂ seeds on citric acid‐treated cotton fabrics followed pseudo second‐order kinetic model and Langmuir isotherm. This indicated that Mg(OH)₂ seeds adsorption was monolayer chemical adsorption driven by electric attraction between positively charged Mg(OH)₂ seeds and ? COO^? ions on the cotton fiber surface. The X‐ray diffraction (XRD) and SEM characterizations of the Mg(OH)₂ thin films covered cotton fabrics found that standing flaky Mg(OH)₂ crystals formed a shell of porous but continuous network on cotton fabric surface. Owing to the Mg(OH)₂ thin film covering, the fabric had fireproof property, lower thermal conductivity and higher optical absorbance in the UV, Vis and IR regions. Copyright © 2010 John Wiley & Sons, Ltd.     

A simple method for determining the total amount of physically and chemically bound water of different cements

A novel environmentally friendly flame-retardant compound, diethyl 3-(triethoxysilanepropyl) phosphoramidate (DTP) was synthesized via a simple one-step procedure with good yield and characterized by FT-IR and ¹H-NMR, ³¹P-NMR and ²⁹Si-NMR. The synthesized compound was coated onto cotton fabrics with different levels of add-ons (5–17 mass%) using the traditional pad-dry-cure method. SEM and XPS were conducted to characterize the surfaces of the coated cotton fabrics. The XPS results showed that DTP was attached to cotton through covalent bond. Cone calorimeter test showed that the cotton fabric treated with DTP became less flammable due to the lower HRR, THR and CO₂/CO ratio. The modified cotton fabrics exhibited efficient flame retardancy, which was evidenced by limiting oxygen index (LOI) and vertical flammability test. Cotton fabrics treated with DTP in 5–17 mass% add-ons had high LOI values of 23–32%. Thermogravimetric analysis results show that the usage of DTP promotes degradation of the cotton fabrics and catalyzes its char formation.     

Design and fabrication of thin polymer coating on cotton fabric surface to impart hydrophobicity: An admicellar polymerization approach

The fluorinated poly(trifluoroethylmethacrylate) thin polymers were successfully prepared through free radical initiating admicellar polymerization approach using fluorosurfactant and 2,2,2-trifluoroethylmethacrylate (TFEM, monomer) system, which was initiated with potassium persulfate (KPS) initiator. The structure of the resultant polymer and morphology of the modified cotton fabric surfaces were confirmed by SEM and EDX analysis. The surface wettability of the modified cotton fabric was characterized by a water drop stay time and contact angle (CA) measurement. The coated cotton fabric exhibited excellent hydrophobicity with a water contact angle of 137.79°.     

Preparation of durable superhydrophobic surface by sol–gel method with water glass and citric acid

Durable superhydrophobic surface on cotton fabrics has been successfully prepared by sol–gel method. Cellulose fabric was first coated with silica sol prepared with water glass and citric acid as the acidic catalyst. The silica coated fabric was then padded with hydrolyzed hexadecyltrimethoxysilane afterwards obtaining low surface energy. Water contact angle and hydrostatic pressure were used to characterize superhydrophobicity and washing durability. Scanning electron microscopy was used to characterize the surface morphology changes after certain washing times. All results showed good durable hydrophobicity on cellulose fabrics. In addition, the influence of citric acid and sodium hypophosphite (NaH₂PO₂) on the durability of hydrophobicity was also investigated. The durability of treated cotton improved with the increase of concentration of citric acid in the presence of NaH₂PO₂. It could be concluded that citric acid acted as multi-functional heterogeneous grafting chemicals to improve washing durability of hydrophobicity by forming the ester bonds between cotton fabric and silica sol and improved the durability of hydrophobicity.     

Hierarchical structure microspheres of PCL block copolymers via electrospraying as coatings for fabric with mechanical durability and self‐cleaning ability

The various morphology and structure microspheres were fabricated via one‐step single‐solvent electrospraying of hydrophilic and hydrophobic block modified copolymer of polycaprolactone (PCL). A honeycomb‐like hierarchical structure microspheres of PCL‐b‐PTFOA(4h) and abundant nanometer pores of PCL‐b‐PEG400 microspheres were obtained due to the solvent evaporation, thermally and polymer diffusion‐induced phase separation effect. Furthermore, a superhydrophobic coatings and robust superhydrophobic‐coated cotton woven fabric surfaces were prepared by using PCL‐b‐PTFOA(4h) microspheres with hierarchical structure and low surface energy. The contact angle (CA) and sliding angle (SA) of PCL‐b‐PTFOA(4h) microspheres‐coated cotton woven fabric surfaces reached 164.4 ± 5.5° and 6.8 ± 0.5°, respectively, which allows for self‐cleaning. The self‐cleaning test demonstrated that the coated superhydrophobic surface could shed aqueous dyes and dust without any trace. The superhydrophobic‐coated fabric shows good soaping fastness against mechanical abrasion without significant reduction of CA. This electrospraying coating of block copolymers can provide a simple, facile, and promising technique for producing multifunctional textiles.     

Synthesis and characterization of a novel phosphorus–nitrogen‐containing flame retardant and its application for textile

The economic and environmentally friendly flame‐retardant compound, tetramethyl (6‐chloro‐1,3,5‐triazine‐2,4‐diyl)bis(oxy)bis(methylene) diphosphonate ( CN‐1 ), was synthesized by a simple two‐step procedure from dimethyl phosphate, and its chemical structure was characterized by ¹H, ¹³C, and ³¹P nuclear magnetic resonance and gas chromatography mass spectroscopy. Using the traditional pad–dry–cure method, we obtained several different add‐ons (wt%) by treating cotton twill fabric with flame retardant ( CN‐1 ). Thermogravimetric analysis, in an air and nitrogen atmosphere, of the modified cotton showed that decomposition occurred ~230°C with 16% residue weight char yield at 600°C, indicating high thermal stability for all treated levels. Limiting oxygen index (LOI) and the vertical flammability test were employed to determine the effectiveness of the flame‐retardant treatments on the fabrics. LOI values increased from ~18 vol% oxygen in nitrogen for untreated fabric to maximum of 34 vol% for the highest treatment level. Fabrics with higher levels of flame retardant also easily passed the vertical flammability test. Furthermore, Fourier transform infrared and scanning electron microscopy were utilized to characterize the chemical structure as well as the surface morphology of the flame‐retardant treated twill fabrics, including char area and the edge between unburned fabric and char area. Copyright © 2011 John Wiley & Sons, Ltd.     

Study of flame-retardant finishing of cellulose fibres: Organic–inorganic hybrid versus conventional organophosphonate

The aim of this study was to introduce a non-formaldehyde inorganic–organic hybrid sol–gel flame-retardant precursor (SiOP) containing phosphorous, nitrogen, and silicon and to compare its functional properties with those of the conventional formaldehyde-containing organic flame-retardant agent, organophosphonate (OP). SiOP was used at concentrations of 2%, 4%, and 8%, and OP was used at a concentration of 200 g/dm³. Both agents were applied to 100% cotton (CO) woven fabric by the pad-dry-cure method under the appropriate conditions. The presence of the SiOP and OP coatings on the CO fabric was confirmed by scanning electron microscopy, energy dispersive X-ray spectroscopy and Fourier-transform infrared spectroscopy. The results of the vertical tests of flammability and the thermogravimetric analyses showed that the presence of the SiOP coating changed the thermal degradation pathway of the CO fabric and resulted in an increase in the thermo-oxidative stability of the cellulose fibres. The thermo-oxidative stability was enhanced by the addition of higher amount of dry solids. At comparable dry solids contents, OP preserved significantly greater flame retardancy and thermo-oxidative stability than did SiOP. These results indicated that the SiOP precursor could not act as an effective alternative to the OP agent in the flame-retardant protection of CO fabric.     

Synthesis of organo-modified α-zirconium phosphate and its effect on the flame retardancy of IFR poly(lactic acid) systems

Novel intumescent flame-retardant poly(lactic acid) (PLA/IFR)/organo-modified α-zirconium phosphate(OZrP) nanocomposites were prepared via incorporation of charring agent (CA), ammonium polyphosphate (APP) and OZrP into PLA. OZrP was synthesized directly by a solvent thermal method. The morphological characterization of PLA/IFR/OZrP nanocomposites was conducted by wide angle X-ray diffraction (WXRD) and transmission electron microscopy (TEM). The effect of the OZrP on flame retardancy and the thermal stability of PLA/IFR composites were studied by thermogravimetric analysis (TGA), limiting oxygen index (LOI), vertical burning test (UL-94) and cone calorimeter test. The TGA data illustrated that the OZrP could increase the residue and significantly improve the flame retardancy of PLA/IFR/OZrP nanocomposites showing an excellent synergistic effect. The addition of OZrP to the flame-retardant PLA increases the LOI and enhances the UL-94 rating. Cone calorimeter tests gave clear evidence that the incorporation of OZrP into PLA/IFR composites resulted in the significant reduction of the heat release rate (HRR), low total heat release (THR) and high amount of char residues during combustion. The flame-retardant mechanism of PLA/IFR/OZrP nanocomposites may correspond to the intumescent flame-retardant mechanism and catalyzed carbonization mechanism caused by OZrP.     

Comparison of different reactive organophosphorus flame retardant agents for cotton. Part II: Fabric flame resistant performance and physical properties

N-Methylol dimethylphosphonopropionamide (MDPA) is one of the most commonly used durable flame retardant agents for cotton. In our previous research, we developed a new flame retardant finishing system based on a hydroxy-functional organophosphorus oligomer (HFPO) and bonding agents, such as dimethyloldihydroxyethyleneurea (DMDHEU) and trimethylolmelamine (TMM). In this research, we compared the flame resistant performance as well as physical properties of the cotton fabric treated with these two flame retardant finishing systems. The cotton fabric treated with MDPA/TMM has a higher initial limiting oxygen index (LOI) than that of the fabric treated with HFPO/TMM due to higher nitrogen content in the system. The LOI of the cotton fabric treated with the HFPO and MDPA systems becomes identical when the treated fabric contains equal amount of phosphorus and nitrogen. The MDPA/TMM shows higher laundering durability on cotton than HFPO/TMM system. The fabric treated with HFPO/TMM and MDPA/TMM has low wrinkle resistance and low strength loss whereas the fabric stiffness significantly increases when the TMM concentration is increased.