极化X光谱诊断铝激光等离子体的电子密度

为了准确诊断激光等离子体的电子密度,提出了一种基于极化光谱的类氦共振线与互组合线相对强度比诊断电子密度的方法.该法考虑了激光等离子体发射的X射线存在极化的特性,用极化光谱理论对测量的类氦共振线和互组合线光谱相对强度比进行精密校正,再推导等离子体的电子密度.在2×10 J激光装置上进行了实验,使用极化PET（002）晶体谱仪测量了Al类氦离子光谱,利用光谱的极化特性推出Al等离子体的电子密度约为1.5×1020 cm－3.结果表明极化X光谱推导等离子体电子密度方法适合激光高温高密等离子体诊断.     

120TW/30fs激光产生的Al等离子体X射线发射谱分析

在SILEX激光装置上利用超强超短激光(120TW/30fs)与Al靶相互作用产生热稠密等离子体.采用类氢共振线与类氦共振线线强比诊断得到电子温度在480～670eV之间,采用类锂jkl伴线与类氦共振线强度比得到电子温度在430～610eV之间,两种诊断方法得到的结果基本一致.用类氦互组合线与类氦共振线强度比方法获得电...     

用He-like离子特征谱线测量等离子体电子温度和电子密度

本文详细叙述了利用He-like离子的特征谱线诊断等离子体的电子密度和电子温度的方法,给出了共振线与双电子伴线的强度比随电子温度的变化曲线和共振线与互组合线的强度比随电子密度的变化曲线。并且根据实验测得的上述两组谱线的强度比,定出激光产生等离子体的电子温度和电子密度。     

铜等离子体电子温度和密度随激光功率的变化

一、引言 激光等离子体X射线(LPX)诊断,是了解等离子体与激光相互作用的最基本手段,也是最早开始研究的课题。早在1968年,Jkunze等人利用类氦离子的组合线与共振线强度比与密度关系,第一次从θ-pinch中测出碳等离子体的电子密度。之后Boiko也计算了镁     

硅类氦离子谱线组的强度诊断

一、引 言 类氦离子共振线的长波侧,除了互组合线外,还存在着大量的双电子伴线。这种双电子伴线跃迁的上能态,有两种形成机制:类氦离子的双电子复合和类锂离子的内壳层激发。有些伴线主要是双电子复合引起的,另一些伴线主要是内壳层激发引起的,还有一些伴线则同时由这两种机制引起。 根据实验测得的类氦离子共振线与互组合线的强度比,可以估算等离子体的电子密度Ne;根据双电子复合伴线与共振线的强度比,可以估算电子温度Te。此外,根据内壳层激     

等离子体效应对类氦氖Kα线系电偶极辐射的影响

采用离子球模型，通过自洽求解Boltzmann方程和Poisson方程，得到类氦氖离子Kα线系的两条电偶极辐射光谱能量随等离子体环境的漂移.结果显示，Kα线系电偶极谱线随等离子体电子密度增大发生红移，红移量与等离子体电子密度有近似的正比关系；随着等离子体电子温度的降低，光谱红移对等离子体电子密度的敏感性增大.另外，所研究的两条谱线间的能量间隔随等离子体电子密度的增大而减小，减小量随等离子体电子密度的变化也呈现出近似的线性规律.值得注意的是，类氦氖Kα线系中两条电偶极谱线分别为互组合线与共振谱线，而其能量差就是1s2p(³P₁)的交换能，因此进一步发现能级中交换能将随等离子体环境变化的规律.所观察到的光谱红移和精细结构分裂在高密度等离子体中都有明显的变化，对探索高密度等离子体的诊断新方法有重要意义. 关键词： 光谱漂移 交换能 等离子体 类氦离子     

辐射输运实验中的Al等离子体发射光谱研究

SGII装置上用八路激光注入金腔产生高温辐射源,然后利用该辐射源来加热输运腔中的掺Al泡沫样品.从测量得到的Al类氦离子发射光谱可以观察到a—d,qr伴线的强度明显高于jkl伴线的强度,由此可以确定出光子激发和电离过程对输运腔中等离子体的形成不可忽略.除此之外,还观察到较强的互组合线发射,这表明存在一个低密度区域.最后考虑到实验测量得到的Al类氦离子发射光谱是时间、空间积分,利用两个状态等离子体的发射光谱合成再现了实验光谱. 关键词： 发射光谱 辐射加热 光谱诊断     

激光等离子体X射线极化光谱诊断

针对波长为0.5～0.8 nm的激光等离子体X射线极化度的诊断,研制了一种新型适用的基于宅问分辨的极化谱仪.在极化谱仪内的垂直和水平通道上分别布置正交的季戊四醇(PET)晶体色散元件.信号采用成像板进行接收,有效接收面积为30 mm×80 mm,从等离子体光源经品体到成像板的光程长为240 mm.通过实验成像板获得了铝激光等离子体X射线的光谱空间分辨信号,分析了获得的类氦谱线和类锂伴线并计算其极化度,并分析了负极化的原因.实验结果表明该谱仪获得的X射线极化度测量值与理论值相符,适合激光等离子体X射线极化光谱的诊断.     

等离子体效应对类氦氖Kα线系电偶极辐射的影响

采用离子球模型,通过自洽求解Boltzmann方程和Poisson方程,得到类氦氖离子Kα线系的两条电偶极辐射光谱能量随等离子体环境的漂移.结果显示,Kα线系电偶极谱线随等离子体电子密度增大发生红移,红移量与等离子体电子密度有近似的正比关系;随着等离子体电子温度的降低,光谱红移对等离子体电子密度的敏感性增大.另外,所研究的两条谱线间的能量间隔随等离子体电子密度的增大而减小,减小量随等离子体电子密度的变化也呈现出近似的线性规律.值得注意的是,类氦氖Kα线系中两条电偶极谱线分别为互组合线与共振谱线,而其能量差就是1s2p(3P1)的交换能,因此进一步发现能级中交换能将随等离子体环境变化的规律.所观察到的光谱红移和精细结构分裂在高密度等离子体中都有明显的变化,对探索高密度等离子体的诊断新方法有重要意义.     

Ti类氦Kα线在高温稠密等离子体中的漂移

采用离子球模型,通过自洽求解Dirac方程和Poisson方程,得到类氦Ti离子Kα线系的两条电偶极辐射光谱能量随不同等离子体环境的变化关系.同时分析了束缚电子交换能随等离子体环境的变化规律.结果表明：光谱能量漂移量随等离子体电子密度变化呈现出很好的线性关系.对此,拟合得到Ti类氦Kα线光谱能量漂移量随等离子体环境参数变化的公式,对探索高温高密度等离子体诊断方法具有一定意义. 关键词： 类氦离子 自洽场离子球模型 光谱漂移 等离子体诊断     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.